Synthesis of fatty acid methyl esters via the transesterification of waste cooking oil by methanol with a barium-modified montmorillonite K10 catalyst

The transesterification of waste cooking oil (WCO) with methanol to produce fatty acid methyl esters (FAMEs) in the presence of barium-modified montmorillonite K10 (BMK10) catalyst was investigated in a batch reactor. The influence of the reaction parameters on the yield of FAME was investigated. The highest value of 83.38% was obtained with 3.5 wt% catalyst loading at 150 °C with a methanol: oil molar ratio of 12:1 during a reaction time of 5 h. BMK10 is a promising low-cost catalyst for the transesterification of WCO to produce FAME.     

Synthesis of fatty acid methyl esters via the methanolysis of palm oil over Ca3.5xZr0.5yAlxO3 mixed oxide catalyst

Novel mixed metal oxide catalyst Ca_3.5xZr_0.5yAl_xO₃ was synthesized through the coprecipitation of metal hydroxides. The textural, morphological, and surface properties of the synthesized catalysts were characterized via Brunauer–Emmett–Teller method, X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and energy-dispersive X-ray spectroscopy. The catalytic performance of the as-synthesized catalyst series was evaluated during the transesterification of cooking palm oil with methanol to produce fatty acid methyl esters (FAME). The influence of different parameters, including the calcination temperature (300–700 °C), methanol to oil molar ratio (6:1–25:1), catalyst amount (0.5–6.5 wt%), reaction time (0.5–12 h) and temperature (70–180 °C), on the process was thoroughly investigated. The metal oxide composite catalyst with a Ca:Zr ratio of 7:1 showed good catalytic activity toward methyl esters. Over 87% of FAME content was obtained when the methanol to oil molar ratio was 12:1, reaction temperature 150 °C, reaction time 5 h and 2.5 wt% of catalyst loading. The catalyst could also be reused for over four cycles.     

Biodiesel from Jojoba oil-wax: Transesterification with methanol and properties as a fuel

The Jojoba oil-wax is extracted from the seeds of the Jojoba (Simmondsia chinensis Link Schneider), a perennial shrub that grows in semi desert areas in some parts of the world. The main uses of Jojoba oil-wax are in the cosmetics and pharmaceutical industry, but new uses could arise related to the search of new energetic crops.This paper summarizes a process to convert the Jojoba oil-wax to biodiesel by transesterification with methanol, catalysed with sodium methoxide (1 wt% of the oil). The transesterification reaction has been carried out in an autoclave at 60 °C, with a molar ratio methanol/oil 7.5:1, and vigorous stirring (600 rpm), reaching a quantitative conversion of the oil after 4 h. The separation of the fatty acid methyl esters (the fraction rich in FAME, 79% FAME mixture; 21% fatty alcohols; 51% of methyl cis-11-eicosenoate) from the fatty alcohols rich fraction (72% fatty alcohols; 28% FAME mixture; 26% of cis-11-eicosen-1-ol, 36% of cis-13-docosen-1-ol) has been accomplished in a single crystallization step at low temperature (−18 °C) from low boiling point petroleum ether.The fraction rich in FAME has a density (at 15 °C), a kinematic viscosity (at 40 °C), a cold filter plugging point and a high calorific value in the range of the European standard for biodiesel (EN 14214).     

Optimization of transesterification conditions for the production of fatty acid methyl ester (FAME) from Chinese tallow kernel oil with surfactant-coated lipase

Surfactant-coated lipase was used as a catalyst in preparing fatty acid methyl ester (FAME) from Chinese tallow kernel oil from Sapium sebiferum (L.) Roxb. syn. Triadica sebifera (L.) small. FAME transesterification was analyzed using response surface methodology to find out the effect of the process variables on the esterification rate and to establish prediction models. Reaction temperature and time were found to be the main factors affecting the esterification rate with the presence of surfactant-coated lipase. Developed prediction models satisfactorily described the esterification rate as a function of reaction temperature, time, dosage of surfactant-coated lipase, ratio of methanol to oil, and water content. The FAME mainly contained fatty acid esters of C16:0, C18:0, C18:1, C18:2, and C18:3, determined by a gas chromatograph. The optimal esterification rate was 93.86%. The optimal conditions for the above esterification ratio were found to be a reaction time of 9.2 h, a reaction temperature of 49 °C, dosage of surfactant-coated lipase of 18.5%, a ratio of methanol to oil of 3:1, and water content of 15.6%. Thus, by using the central composite design, it is possible to determine accurate values of the transesterification parameters where maximum production of FAME occurs using the surfactant-coated lipase as a transesterification catalyst.     

Biodiesel production by esterification of palm fatty acid distillate

Production of fatty acid methyl ester (FAME) from palm fatty acid distillate (PFAD) having high free fatty acids (FFA) was investigated in this work. Batch esterifications of PFAD were carried out to study the influence of: including reaction temperatures of 70–100 °C, molar ratios of methanol to PFAD of 0.4:1–12:1, quantity of catalysts of 0–5.502% (wt of sulfuric acid/wt of PFAD) and reaction times of 15–240 min. The optimum condition for the continuous esterification process (CSTR) was molar ratio of methanol to PFAD at 8:1 with 1.834 wt% of H₂SO₄ at 70 °C under its own pressure with a retention time of 60 min. The amount of FFA was reduced from 93 wt% to less than 2 wt% at the end of the esterification process. The FAME was purified by neutralization with 3 M sodium hydroxide in water solution at a reaction temperature of 80 °C for 15 min followed by transesterification process with 0.396 M sodium hydroxide in methanol solution at a reaction temperature of 65 °C for 15 min. The final FAME product met with the Thai biodiesel quality standard, and ASTM D6751-02.     

Biodiesel production from soybean and Jatropha oils using cesium impregnated sodium zirconate as a heterogeneous base catalyst

Cesium modified sodium zirconate (Cs-Na₂ZrO₃) was prepared by ionic exchange from sodium zirconate (Na₂ZrO₃), which was synthesized via a solid state reaction. Both ceramics, i.e., pristine Na₂ZrO₃ and the Cs-Na₂ZrO₃, were used as basic heterogeneous catalysts in biodiesel production. Soybean and Jatropha oils were used as triglyceride sources for transesterification reactions. Parameters, such as catalyst concentration (between 0.5 and 3 wt%), reaction time, different methanol/vegetable oil molar ratios, and temperature of the reaction, were evaluated. The cesium cation influence was evaluated from the basic transesterification reactivity. The results showed that the introduction of cesium significantly modified the catalytic activity in biodiesel production. Cs enhanced the reaction kinetics in obtaining biodiesel and reduced the reaction time in comparison with pristine Na₂ZrO₃. The results showed that Cs-Na₂ZrO₃ as a basic heterogeneous catalyst exhibited the best fatty acid methyl esters (FAME) conversion for soybean oil (98.8%) at 1 wt%, 30:1 methanol/oil ratio, 65 °C, and 15 min. The best conditions for Jatropha oil (90.8%) were 3 wt%, 15:1 methanol/oil ratio, 65 °C, and 1 h. The impregnation of Na₂ZrO₃ with cesium represents a very exciting alternative heterogeneous base catalyst for biodiesel production.     

Acid-catalyzed production of biodiesel from waste frying oil

The reaction kinetics of acid-catalyzed transesterification of waste frying oil in excess methanol to form fatty acid methyl esters (FAME), for possible use as biodiesel, was studied. Rate of mixing, feed composition (molar ratio oil:methanol:acid) and temperature were independent variables. There was no significant difference in the yield of FAME when the rate of mixing was in the turbulent range 100 to 600 rpm. The oil:methanol:acid molar ratios and the temperature were the most significant factors affecting the yield of FAME. At 70 °C with oil:methanol:acid molar ratios of 1:245:3.8, and at 80 °C with oil:methanol:acid molar ratios in the range 1:74:1.9–1:245:3.8, the transesterification was essentially a pseudo-first-order reaction as a result of the large excess of methanol which drove the reaction to completion (99±1% at 4 h). In the presence of the large excess of methanol, free fatty acids present in the waste oil were very rapidly converted to methyl esters in the first few minutes under the above conditions. Little or no monoglycerides were detected during the course of the reaction, and diglycerides present in the initial waste oil were rapidly converted to FAME.     

Biodiesel production from palm oil via heterogeneous transesterification

This paper presents the study of the transesterification of palm oil via heterogeneous process using montmorillonite KSF as heterogeneous catalyst. This study was carried out using a design of experiment (DOE), specifically response surface methodology (RSM) based on four-variable central composite design (CCD) with α (alpha) = 2. The transesterification process variables were reaction temperature, x₁ (50–190 °C), reaction period, x₂ (60–300 min), methanol/oil ratio, x₃ (4–12 mol mol^?1) and amount of catalyst, x₄ (1–5 wt%). It was found that the yield of palm oil fatty acid methyl esters (FAME) could reach up to 79.6% using the following reaction conditions: reaction temperature of 190 °C, reaction period at 180 min, ratio of methanol/oil at 8:1 mol mol^?1 and amount of catalyst at 3%.     

Study on the use of MgAl hydrotalcites as solid heterogeneous catalysts for biodiesel production

This paper, reports experimental work on the use of new heterogeneous solid basic catalysts for biodiesel production: double oxides of Mg and Al, produced by calcination, at high temperature, of MgAl lamellar structures, the hydrotalcites (HT). The most suitable catalyst system studied are hydrotalcite Mg:Al 2:1 calcinated at 507 °C and 700 °C, leading to higher values of FAME also in the second reaction stage. One of the prepared catalysts resulted in 97.1% Fatty acids methyl esters (FAME) in the 1st reaction step, 92.2% FAME in the 2nd reaction step and 34% FAME in the 3rd reaction step. The biodiesel obtained in the transesterification reaction showed composition and quality parameters within the limits specified by the European Standard EN 14214. 2.5% wt catalyst/oil and a molar ratio methanol:oil of 9:1 or 12:1 at 60–65 °C and 4 h of reaction time are the best operating conditions achieved in this study. This study showed the potential of Mg/Al hydrotalcites as heterogeneous catalysts for biodiesel production.     

Fatty acid methyl ester production from wet microalgal biomass by lipase-catalyzed direct transesterification

The aim of this work was to optimize the production of fatty acid methyl ester (FAME, biodiesel) from wet Nannchloropsis gaditana microalgal biomass by direct enzymatic transesterification. This was done in order to avoid the high cost associated with the prior steps of drying and oil extraction. Saponifiable lipids (SLs) from microalgal biomass were transformed to FAME using the lipase Novozyme 435 (N435) from Candida antarctica as the catalyst, and finally the FAME were extracted with hexane. t-Butanol was used as the reaction medium so as to decrease lipase deactivation and increase mass transfer velocity. A FAME conversion of 99.5% was achieved using wet microalgal biomass homogenized at 140 MPa to enhance cell disruption, a N435:oil mass ratio of 0.32, methanol added in 3 stages to achieve a total of 4.6 cm³ g⁻¹ of oil and 7.1 cm³ g⁻¹ oil of added t-butanol, with a reaction time of 56 h. The FAME conversion decreased to 57% after catalyzing three reactions with the same lipase batch. This work shows the influence of the polar lipids contained in the microalgal biomass both on the reaction velocity and on lipase activity.     

Kinetics of biofuel generation from deodorizer distillates derived from the physical refining of olive oil and squalene recovery

The recovery of squalene from deodorizer distillate derived from the physical refining of olive oil was evaluated by combining pressurized acidic esterification in a closed system with vacuum distillation. Esterification was carried out at 341, 359, 366, 391 and 395 K. The reaction at 395 K was found to be satisfactory as it decreased the acid value by 99.21% and generated a FAME concentration of 67.53% within 1 h. In order to demonstrate that the generation of FAME from deodorizer distillate was mainly due to the transformation of FFA, the reaction extent, which characterizes the reaction and simplifies calculations, was evaluated for FFA removal and the generation of FAME. Subsequent vacuum distillation allowed the separation of one fraction rich in FAME (94%), which can be used as a biofuel and accounted for 85% of the initial mass, and another fraction that was rich in squalene (78%) and may be used for manufacturing pharmaceutical products. The global squalene yield was 117 g kg⁻¹ initial deodorizer distillate.     

The influence of free fatty acid intermediate on biodiesel production from soybean oil by whole cell biocatalyst

The whole cell of lipase-producing Rhizopus oryzae was employed as biocatalyst for transesterification of soybean oil containing oleic acid. The free fatty acid (FFA) intermediate, playing an important role in the kinetics of transesterification of soybean oil, was thoroughly investigated and characterized. The conversion was more than 97% at the initial FFA content of 5.5%. A high content of FFA could protect the lipase from denaturation. The 34.6 percent of FFA with the optimal 26-mg mL⁻¹ methanol resulted in a specific reaction rate of 420 mg h⁻¹g-dry cell⁻¹. In addition, the methanol/FFA ratio at 0.83-1.7 provides a good indication of the fatty acid methyl esters conversions for different initial FFA contents. In the transesterification process, more FFA intermediate present would become beneficial to conversion of retrograde feedstock to biodiesel. The immediately generated and original FFA content become the major rate-determining factor in the FFA-mixed transesterification process.     

Lithium ion impregnated calcium oxide as nano catalyst for the biodiesel production from karanja and jatropha oils

Lithium impregnated calcium oxide has been prepared by wet impregnation method in nano particle form as supported by powder X-ray diffraction and transmission electron microscopy. Basic strength of the same was measured by Hammett indicators. Calcium oxide impregnated with 1.75 wt% of lithium was used as solid catalyst for the transesterification karanja and jatropha oil, containing 3.4 and 8.3 wt% of free fatty acids, respectively. The reaction parameters, viz., reaction temperature, alcohol to oil molar ratio, free fatty acid contents, amount of catalyst and amount of impregnated lithium ion in calcium oxide support, have been studied to establish the most suitable condition for the transesterification reaction. The complete transesterification of karanja and jatropha oils was achieved in 1 and 2 h, respectively, at 65 °C, utilizing 12:1 molar ratio of methanol to oil and 5 wt% (catalyst/oil, w/w) of catalyst. Few physicochemical properties of the prepared biodiesel samples have been studied and compared with standard values.     

Biodiesel from mutton fat using KOH impregnated MgO as heterogeneous catalysts

The use of MgO impregnated with KOH as heterogeneous catalysts for the transesterification of mutton fat with methanol has been evaluated. The mutton fat (fat) with methanol (1:22 M ratio) at 65 °C showed > 98% conversion to biodiesel with 4 wt% of MgO–KOH-20¹ (MgO impregnated with 20 wt% of KOH) in 20 min. The reaction conditions optimized were; the amount of KOH impregnation (5–20 wt%), the amount of catalyst (1.5–4 wt%, catalyst/fat), the reaction temperature (45–65 °C), fat to methanol molar ratio (1:11–1:22) and the effect of addition of water/oleic acid/palmitic acid (upto 1 wt%). Although, transesterification of fresh fat (moisture content 0.02 wt% and free fatty acids 0.002 wt%) with methanol in the presence of KOH (homogenous catalyst) resulted in the complete conversion to biodiesel, but in the presence of additional 1 wt% of either free fatty acid or moisture content, formation of soap was observed. The MgO–KOH-20 catalyst was found to tolerate additional 1 wt% of either the moisture or FFAs in the fat.     

Transesterification of canola oil as biodiesel over Na/Zr-SBA-15 catalysts: Effect of zirconium content

A series of mesoporous Zr-SBA-15-supported Na catalysts was prepared and applied to the heterogeneous catalysis of canola oil transesterification. The effects of Si/Zr ratio, reaction time, and percentage of Na loading on the conversion to fatty acid methyl esters (FAME) were studied. The dependence of the textural structure and chemical properties of Zr-SBA-15 supports on Zr content was investigated using small-angle X-ray diffraction, Brunauer–Emmett–Teller analysis, transmission electron microscopy (TEM), and Fourier transform infrared (FTIR) spectroscopy. The results obtained from FTIR and TEM indicate that the incorporation of Zr atoms into the SBA-15 structure facilitated the formation of Brönsted acid sites and decreased the particle size of Na species. Catalysts with a higher Zr content enhanced the FAME yield. The optimum conditions determined were as follows: reaction temperature of 70 °C, 15 wt.% Na, reaction time of 6 h, and 12% catalyst content (wt.% oil) with a methanol/oil molar ratio of 6:1. The optimum conditions resulted in a FAME yield of up to 99%.     

Screening,optimization and kinetics of Jatropha curcas oil transesterification with heterogeneous catalysts

This work investigates the production of fatty acid methyl esters (FAME) from Jatropha curcas oil using a variety of heterogeneous catalysts: resins, zeolites, clays, hydrotalcites, aluminas and niobium oxide. For this purpose, a catalyst screening was first conducted in a batch reactor at the following operating conditions: oil to methanol molar ratio of 1:9, 6 h of reaction, 5 wt% catalyst, at 333 and 393 K. From the screening step, KSF clay and Amberlyst 15 catalysts were selected to carry out a 2³ full factorial central composite rotatable design so as to elucidate the effects of process variables on FAME yield. The optimum reaction conditions for both catalysts were found to be oil to methanol molar ratio of 1:12, 5 wt% of catalyst, 433 K and 6 h of reaction with a FAME yield of about 70 wt%. A kinetic study was then experimentally performed and a semi-empirical model was built to represent the experimental data. Finally, catalyst re-utilization in five successive batch experiments was evaluated at the optimized conditions.     

Optimization of biodiesel production from waste fish oil

The present study deals with the production of biodiesel using waste fish oil. The research assesses the effect of the transesterification parameters on the biodiesel yield and its properties, including temperature (40–60 °C), molar ratio methanol to oil (3:1–9:1) and reaction time (30–90 min). The experimental results were fitted to complete quadratic models and optimized by response surface methodology. All the biodiesel samples presented a FAME content higher than 93 wt.% with a maximum, 95.39 wt.%, at 60 °C, 9:1 of methanol to oil ratio and 90 min. On the other hand, a maximum biodiesel yield was found at the same methanol to oil ratio and reaction time conditions but at lower temperature, 40 °C, which reduced the saponification of triglycerides by the alkaline catalyst employed. Adequate values of kinematic viscosity (measured at 30 °C) were obtained, with a minimum of 6.30 mm²/s obtained at 60 °C, 5.15:1 of methanol to oil ratio and 55.52 min. However, the oxidative stability of the biodiesels produced must be further improved by adding antioxidants because low values of IP, below 2.22 h, were obtained. Finally, satisfactory values of completion of melt onset temperature, ranging from 3.31 °C to 3.83 °C, were measured.     

催化合成生物柴油的双金属络合物固体催化剂

制备了基于亚铁氰化锌的双金属氰化物络合物(DMC),可一步同时催化酯交换和酯化反应制备生物柴油,该催化剂体系具有不受水毒性影响的特点。用3wt%的DMC催化剂在433K,醇油摩尔比为16∶1以及水和脂肪酸含量各10wt%的条件下分别同时催化甘油三酯、脂肪酸和甲醇的酯交换、酯化反应,生物柴油产率可达98%以上。对催化剂进行X射线衍射、热重红外联用分析、元素分析、比表面积和孔体积测定、扫描电镜等手段表征,结果表明:该催化剂为晶态与非晶态组分混合结构,其表面晶态决定其在高水含量、高酸值的环境下仍具有较好的催化活性,验证得出活性位点可能为锌离子。     

Production of ethyl ester from esterified crude palm oil by microwave with dry washing by bleaching earth

The production of ethyl ester from a feed material of esterified crude palm oil with 1.7 wt% of free fatty acid (FFA) content using microwave heating was investigated. Parametric studies were carried out to investigate the optimum conditions for the transesterification process (amount of ethanol, amount of catalyst and reaction time). As a result, optimum reaction parameters for the transesterification process aided by microwave heating have been identified: a molar ratio of oil to ethanol of 1:8.5, 1.5 wt% of KOH/oil, a reaction time of 5 min and a microwave power of 70 W. Glycerin from the ester phase was separated by adding 10 wt% of pure glycerin. The ethyl ester was purified with 1.2 wt% of bleaching earth to remove the residual catalyst and residual glycerin. This transesterification process provided a yield of 85 wt% with an ester content of 98.1 wt%. The final ethyl ester product met the specifications stipulated by ASTM D6751-02.     

Optimization of heterogeneous biodiesel production from waste cooking palm oil via response surface methodology

Heterogeneous transesterification of waste cooking palm oil (WCPO) to biodiesel over Sr/ZrO₂ catalyst and the optimization of the process have been investigated. Response surface methodology (RSM) was employed to study the relationships of methanol to oil molar ratio, catalyst loading, reaction time, and reaction temperature on methyl ester yield and free fatty acid conversion. The experiments were designed using central composite by applying 2⁴ full factorial designs with two centre points. Transesterification of WCPO produced 79.7% maximum methyl ester yield at the optimum methanol to oil molar ratio = 29:1, catalyst loading = 2.7 wt%, reaction time = 87 min and reaction temperature = 115.5 °C.