PPS/PA66/GF复合材料的制备及性能研究

在聚苯硫醚（PPS）树脂基体中引入聚酰胺66（PA66）,随着PA66含量增加,PPS/PA66共混物的拉伸强度和弯曲强度逐渐下降,结合PPS/PA66共混物的相形貌分析,提出了通过玻璃纤维（GF）的引入,制备具有互锁结构的PPS/PA66/GF三元体系复合材料,达到同时提高复合材料的强度、刚度及韧性的目的。分别考察了短玻璃纤维（SGF）和中长玻璃纤维（LGF）增强PPS/PA66的综合性能。结果表明,GF的引入显著提高了共混物的力学性能,同时,PPS/PA66/SGF和PPS/PA66/LGF复合材料的扫描电子显微镜和动态力学性能分析都表明共混物内部形成了一个高度互锁的结构。     

Preparation and Mechanical Properties of Long Glass Fiber Reinforced PA6 Composites Prepared by a Novel Process

Summary: Long glass fiber reinforced PA6 (LGF/PA6) prepregs were prepared by impregnating PA6 oligomer melt into reinforcing glass fiber followed by subsequent solid‐state polymerization (SSP) to obtain LGF/PA6 composite pellets. A conventional injection‐molding machine suitable for short glass fiber reinforced composites was applied to the processing of the prepared composites, which reduced the fiber length in the final products. Mechanical properties, thermal property, and fiber length distribution of injection molding bars were investigated. Scanning electron microscopy (SEM) was used to observe the impact fracture surfaces and the surfaces of glass fiber after the SSP. It was found that the LGF/PA6 composites were of favorable mechanical properties, especially the impact strength, although the average length of glass fiber was rather short. By this novel process, the content of glass fiber in composite could be high up to 60 wt.‐% and the maximum level of heat distortion temperature (HDT) was close to the melting temperature of PA6. SEM images indicated the favorable interfacial properties between the glass fiber and matrix. The glass fiber surfaces were further observed by SEM after removing the matrix PA6 with a solvent, the results showed that PA6 macromolecules were grafted onto the surface. Furthermore, the grafting amount of PA6 was increased with SSP time.

SEM images of impact fracture surfaces of LGF/PA6 composites (left) and of glass fiber surfaces after removing PA6 with 5 h SSP (right).     

Performance of long glass fiber‐reinforced polypropylene composites at different injection temperature

Long glass fiber‐reinforced polypropylene composites were prepared using self‐designed impregnation device. Effects of the different injection temperature on mechanical properties, crystallization, thermal, and dynamic mechanical properties of long glass fiber‐reinforced polypropylene composites were discussed. The differential scanning calorimetry (DSC) results indicate that the melting peak temperature of PP/LGF composites gradually reduced, however, the crystallinity of PP/LGF composites gradually increased with increasing injection temperature. Thermo‐gravimetric analyzer (TGA) results demonstrate that with increasing injection temperature, the temperature of the PP/LGF composites melt increased, the viscosity of the PP/LGF composites melt lowered, the mold filling of the PP/LGF composites melt was easy, the shear force of glass fiber was relatively low, which made the residual length of glass fiber in products increase. Dynamic thermal mechanical analyzer (DMA) results show that the storage modulus of PP/LGF composites is the highest while the injection temperature is at 290°C, and the peak value of tan σ of PP /LGF composites at 290°C is minimal, which indicates that the mechanical properties of PP /LGF composites at 290°C is the best. What' more, the injection temperature at 290°C significantly ameliorated “glass fiber rich skin” of products of glass fiber‐reinforced composites. J. VINYL ADDIT. TECHNOL., 24:233–238, 2018. © 2016 Society of Plastics Engineers     

Influence of thermooxidative aging on the static and dynamic mechanical properties of long‐glass‐fiber‐reinforced polyamide 6 composites

The static and dynamic mechanical properties, thermal behaviors, and morphology of pure long‐glass‐fiber‐reinforced samples [polyamide 6 (PA6)/long glass fiber (LGF)] with different thermal exposure times at 160°C were studied by comparison with stabilized samples in this study. The aging mechanism of the PA6/LGF samples under heat and oxygen was studied with the methods of thermal Fourier transform infrared (FTIR), differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy (SEM), and so on. The results indicate that the static mechanical strength, melting temperature, and crystallization temperature decreased because of the decomposition of the macromolecular chain of PA6 resin and the debonding of the interface between the glass fibers and matrix. The glass‐transition temperature and crystallinity also increased and decreased, respectively, after aging. The macromolecular chain decomposition dominated in the subsequent aging process; this resulted in many sharp and brittle microcracks appearing on the surfaces of the aged samples, as shown by SEM and the FTIR spectra. The existence of stabilizers endowed the PA6/LGF composites with better retention of static and dynamic mechanical properties. The reason was that the metal ions of the copper salt antioxidant acted as an anti‐aging catalyst in the reinforced PA6 system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39594.     

长玻璃纤维增强聚丙烯复合材料的力学性能研究

采用熔体浸渍技术制备了长玻璃纤维母料(LGF/PP-g-MAH/PP)增强聚丙烯(PP)复合材料(LGF/PP)。通过双螺杆挤出机制备了同等配比的短玻纤增强聚丙烯(SGF/PP)复合材料。研究了LGF含量、环氧树脂(EP)和固化剂(2E4MZ)对LGF/PP复合材料的力学性能影响。结果表明:当LGF质量分数为35%～40%时,LGF/PP的综合力学性能最好,且明显优于同样组成的SGF/PP复合材料。EP和含固化剂(2E4MZ)的EP对LGF/PP复合材料的力学性能提高有一定的作用。SEM照片分析表明:EP的加入能改善玻纤与聚丙烯基体的界面粘接。     

耐水解玻璃纤维增强尼龙66的制备及性能研究

制备了长玻璃纤维（LGF）和短玻璃纤维（SGF）增强尼龙66（PA66）,考察了GF、GF分散剂、耐水解改性剂（MPP）对增强PA66性能的影响。结果表明,选择SGF可获得较好力学性能和表面质量的增强PA66;随着SGF含量的增加,材料的拉伸强度、弯曲强度有大幅度的提高,冲击强度则先升高后降低;GF分散剂的加入改善了材料的表面质量;MPP的加入使材料的耐水解性有明显提高。     

Short glass fiber reinforced ABS and ABS/PA6 composites: Processing and characterization

In this study acrylonitrile‐butadiene‐styrene (ABS) terpolymer was reinforced with 3‐aminopropyltrimethoxysilane (APS)‐treated short glass fibers (SGFs). The effects of SGF concentration and extrusion process conditions, such as the screw speed and barrel temperature profile, on the mechanical properties of the composites were examined. Increasing the SGF concentration in the ABS matrix from 10 wt% to 30 wt% resulted in improved tensile strength, tensile modulus and flexural modulus, but drastically lowered the strain‐at‐break and the impact strength. The average fiber length decreased when the concentration of glass fibers increased. The increase in screw speed decreased the average fiber length, and therefore the tensile strength, tensile modulus, flexural modulus, and impact strength were affected negatively and the strain‐at‐break was affected positively. The increase in extrusion temperature decreased the fiber length degradation, and therefore the tensile strength, tensile modulus, flexural modulus, and impact strength increased. At higher temperatures the ABS matrix degraded and the mechanical strength of the composites decreased. To obtain a strong interaction at the interface, polyamide‐6 (PA6) at varying concentrations was introduced into the ABS/30 wt% SGF composite. The incorporation and increasing amount of PA6 in the composites broadened the fiber length distribution (FLD) owing to the low melt viscosity of PA6. Tensile strength, tensile modulus, flexural modulus, and impact strength values increased with an increase in the PA6 content of the ABS/PA6/SGF systems due to the improved adhesion at the interface, which was confirmed by the ratio of tensile strength to flexural strength as an adhesion parameter. These results were also supported by scanning electron micrographs of the ABS/PA6/SGF composites, which exhibited an improved adhesion between the SGFs and the ABS/PA6 matrix. POLYM. COMPOS. 26:745–755, 2005. © 2005 Society of Plastics Engineers     

Mechanical,thermal, and dynamic mechanical properties of long glass fiber‐reinforced thermoplastic polyurethane/polyoxymethylene composites

Long glass fiber (LGF)‐reinforced thermoplastic polyurethane (TPU) elastomers and polyoxymethylene (POM) (LGF/TPU/POM) composites were prepared by using self‐designed impregnation device. Dynamic mechanical properties of the LGF/TPU/POM composites have been investigated by using dynamic mechanical thermal analysis. The results indicated that the storage modulus and glass transition temperature of the composites increase with increasing the glass fibers content and scanning frequencies. In addition, the Arrhenius relationship has been used to calculate the activation energy of α‐transition of the LGF/TPU/POM composites. The thermal stability of the LGF/TPU/POM composites was investigated by thermogravimetric analysis. The consequence demonstrated that the thermal stability increase with augmenting the content of glass fibers. The mechanical properties of the composites are investigated by a universal testing machine and a ZBC‐4 Impact Pendulum. The results demonstrated the mechanical properties of the composites aggrandize with augmenting the glass fibers content. The good dispersion of the LGFs in the matrix resins is obtained from scanning electron micrographs. POLYM. COMPOS., 35:2067–2073, 2014. © 2014 Society of Plastics Engineers     

Effect of impregnation time on performance of long glass fiber‐reinforced polypropylene composites

Long glass fiber (LGF)‐reinforced polypropylene (PP) composites were prepared using self‐designed impregnation device. Effects of impregnation time on mechanical properties, crystallization, dynamic mechanical properties, and morphology of PP/LGF composites were investigated. The experiment results demonstrate that the excellent tensile strength, Notched Izod impact strength was 152.9 MPa, 31.2 KJ/m², respectively, and the stiffness of PP/LGF composites was higher, when the impregnation time was 7.03 s. The excellent interfacial adhesion between PP and glass fiber indicates that PP/LGF composites possess the outstanding mechanical properties. The impregnation time scarcely influenced thermal properties of PP/LGF composites. J. VINYL ADDIT. TECHNOL., 24:174–178, 2018. © 2016 Society of Plastics Engineers     

长玻纤增强尼龙66复合材料性能的研究

在自制装置中用硅烷偶联剂KH550对长玻纤(LGF)进行表面处理后,采用熔融共混法制备了尼龙66/长玻纤复合材料。采用微机全自动热膨胀系数测定仪记录了玻纤增强尼龙66复合材料的热膨胀曲线,分析了玻纤含量、温度对复合材料热膨胀系数的影响,结果表明,随着玻纤含量的增加,复合材料的热膨胀系数显著下降,最大降低了74.2%;随着温度的升高,复合材料的热膨胀系数先增大后减小最后趋于平衡,转折温度在37℃左右。测试了复合材料的力学性能,结果显示复合材料的拉伸强度、弯曲强度和缺口冲击强度随玻纤含量的增加而大幅度提高,最大分别增加了173%、186%和283%。通过扫描电镜观察到玻纤嵌入尼龙66基体中,与尼龙66形成了良好的界面黏结。     

长玻璃纤维增强PA66复合材料的综合性能及其影响因素研究

利用定制的熔融浸渍装置制备了长玻璃纤维增强聚酰胺66(PA66/LGF)复合材料,并对其力学性能、界面黏结性等进行了表征,探讨了玻璃纤维含量、润滑剂含量、相容剂含量以及切粒长度等因素对复合材料性能的影响,得到了PA66/LGF复合材料优化的配方设计与切粒长度.结果表明,当玻璃纤维含量为43％(质量分数,下同)、切粒长度...     

Study on short glass fiber‐reinforced poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) composites

Biobased non‐fossil polyester poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P3/4HB) containing 4.0 mol % 4‐hydroxybutyrate (4HB) was melt‐mixed with short glass fibers (SGF) via a co‐rotating twin‐screw extruder. The compositing conditions, average glass fiber length and distribution, thermal, crystallization, and mechanical properties of the P3/4HB/SGF composites were investigated. Calcium stearate, two kinds of paraffin wax and modified ethylene bis‐stearamide (TAF) were investigated as lubricants for the P3/4HB/SGF composites. It revealed that TAF is the most efficient lubricant of the P3/4HB/SGF composites. Coupling agents 2,2′‐(1,3‐phenylene)bis‐2‐oxazoline (1,3‐PBO) and pyromellitic dianhydride (PMDA) were used as end‐group crosslinkers to reduce the degradation of P3/4HB and increase the mechanical properties of the P3/4HB/SGF composites. It showed that 1,3‐PBO is the efficient coupling agent. The optimum condition of the P3/4HB/SGF composites is 1.5 phr TAF, 1.0 phr 1,3‐PBO, and 30 wt % glass fiber content. And the maximum of tensile strength, tensile modulus, and impact strength of the composites is 3.7, 6.6, 1.8 times of the neat P3/4HB polymer, respectively. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

UV老化对ZnO填充PA6/LGF复合材料性能的影响

用熔融共混法制备出长玻璃纤维(LGF)含量为30%的LGF增强尼龙6(PA6)/ZnO(PA6/LGF/ZnO)复合材料,并采用氙灯紫外(UV)老化法研究了ZnO含量为0%~8%及UV老化时间为0~800 h对复合材料力学性能和结晶性能的影响。结果表明,经UV辐照后,PA6/LGF/ZnO复合材料的拉伸强度升高,韧性下降,其中当ZnO添加量为6%时,复合材料在800 h老化后的拉伸强度和缺口冲击强度保留率较未添加ZnO的复合材料分别提高了5.39%和4.98%。SEM分析表明在UV老化过程中,LGF与PA6基体之间的界面并未受到明显破坏,老化主要集中发生在PA6基体上。随着老化时间的延长,PA6/LGF复合材料中的PA6出现UV交联而使其结晶度从26.19%降低至20.70%;对于ZnO含量为6%的PA6/LGF/ZnO复合材料,老化800 h后其结晶度仅从22.92%下降至21.34%,PA6/LGF/ZnO复合材料整体上的结晶性能趋于稳定。     

Extrusion blow molding of long fiber reinforced polyolefins

A 58% (by weight) long glass fiber reinforced (LGF)‐HDPE master batch was blended with a typical blow molding HDPE grade. HDPE composites having between 5% and 20% (by weight) long fiber content were extruded at different processing conditions (extrusion speed, die gap, hang time). The parison swell (diameter and thickness) decreased with increasing fiber content. Although the HDPE exhibited significant shear rate dependence, the LGF/HDPE composites were shear rate insensitive. Both the diameter and weight swell results also indicated very different sagging behavior. The LGF/HDPE parisons did sag as a solid‐body (equal speed at different axial locations) governed by the orientation caused by the flow in the die. Samples taken from blown bottles showed that fiber lengths decreased to 1‐3 mm, from the original 11 mm fiber length fed to the extruder. No significant difference in fiber length distribution was found when samples for different regions of the bottle were analyzed. SEM micrographs corroborate the absence of fiber segregation and clustering or the occurrence of fiber bundles (homogeneous spatial fiber distribution) as well as a preferential fiber orientation with the direction of flow. The blowing step did not change the orientation of the fibers. Five‐percent (5%) and 10% LGF/HDPE composites could be blown with very slight variations to the neat HDPE inflation conditions. However, 20% LGF/HDPE composites could not be consistently inflated. Problems related to blowouts and incomplete weldlines were the major source of problems.     

Influence of thermo‐oxidative aging on the dynamical mechanical properties and thermal degradation kinetics of glass fiber‐reinforced PA10T composites

Unveiling the fundamental thermal‐oxidative aging mechanism and thermal degradation kinetics of the poly(decamethyleneterephthalamide) (PA10T)/ glass fiber (GF) composites under different aging temperatures (160°C, 200°C, and 240°C) for 0–50 days will facilitate the understanding of the interaction between matrix PA10T and GF. The results revealed that the decrease of mechanical properties referring to tensile strength, flexural strength and notched impact strength, and the occurrence of debonding phenomenon between PA10T matrix and GF were increasingly obvious after longer aging time at higher aging temperature. At the same time, the decline of crystalline was mainly ascribed to the thermal‐oxidative aging effect, which triggered the deterioration of mechanical properties of PA10T/GF composites. Accordingly, the enhancement of rigidity were probably attributed to the higher temperature aging effect with the aging time prolonging in PA10T/GF composites, while the interfacial debonding between GF and resin matrix obviously occurred with the increase of aging time. In a word, it is believed that investigating the fundamental thermal‐oxidative aging of PA10T/GF composites would be beneficial to optimize and control the service life and applications of materials. POLYM. ENG. SCI., 59:643–656, 2019. © 2018 Society of Plastics Engineers     

长玻纤增强热塑性复合材料阻燃改性及老化性能研究进展

综述了近几年来长玻璃纤维(LGF)增强热塑性复合材料的发展现状,重点以聚丙烯为例,介绍了纤维含量、分布及纤维与基体之间相容性等因素对LGF增强热塑性复合材料性能的影响;重点以尼龙6为例,对LGF增强热塑性复合材料的阻燃改性及老化性能的相关研究进行了阐述。最后对未来LGF增强热塑性复合材料改性及抗老化研究的重点和方向进行了展望。     

Preparation,structure, and properties of the PTT/SGF composites

Short glass fiber reinforced poly(trimethylene terephthalate) composites (PTT/SGF) were prepared by twin screw extruder. The structural feature and physical properties of these composites were studied by scanning electron microscope, differential scanning calorimetry, thermalgravimetric analyzer, capillary rheometer, universal tester, etc. The glass fiber was modified by the silane coupling agent before being blended with the polymer. The results suggest that there is strong interaction between SGF and PTT matrix, which leads to an increasing on the tensile strength, Young's modulus, impact strength and thermal stability of the composites with proper contents of SGF. Rheological behavior of the PTT/SGF composites melt is complicated, combining a dilate fluid at lower shear rate and a pseudo-plastic fluid at higher shear rate. The melt apparent viscosity of composites decreases with increasing SGF content because of the rigid fibers improving the flow of the melt. Moreover, the flow activation energy of the composites suggests that the melt with more SGF has lower sensitivity to the processing temperature. In conclusion, the composite with 10–20 wt% content of SGF has better properties. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Thermo‐physical,thermal degradation,and flexural properties of betel nut husk fiber reinforced vinyl ester composites

This study aims to investigate the thermo‐physical, mechanical, and thermal degradation properties of betel nut husk (BNH) fiber reinforced vinyl ester (VE) composites. These properties were evaluated as a function of fiber maturity, fiber content, and fiber orientation. Thermo‐physical properties were analyzed experimentally using a hot disk TPS method. The introduction of BNH was found to reduce the thermal conductivity of neat VE. The thermal conductivity and thermal diffusivity of BNH reinforced VE composites decreased with the increase in fiber content. Short fiber BNH reinforced VE composites showed the lowest thermal conductivity as compared to the unidirectional and random nonwoven composites. The TGA analysis shows lower resin transition peak for the BNH reinforced VE composites than the peak of neat VE. Fiber maturity had a notable effect on the flexural modulus of the BNH fiber reinforced VE composites. Incorporation of 10 wt% BNH fibers into the composite has increased the composites' flexural modulus by 46.37%. However, further increases in the fiber content reduced both flexural strength and modulus of the composites. POLYM. COMPOS., 37:2008–2017, 2016. © 2015 Society of Plastics Engineers     

Effects of polyamide 6 incorporation to the short glass fiber reinforced ABS composites: an interfacial approach

The properties of 30 wt% short glass fiber (SGF) reinforced acrylonitrile-butadiene-styrene (ABS) terpolymer and polyamide 6 (PA6) blends prepared with extrusion were studied using the interfacial adhesion approach. Work of adhesion and interlaminar shear strength values were calculated respectively from experimentally determined interfacial tensions and short beam flexural tests. The adhesion capacities of glass fibers with different surface treatments of organosilanes were evaluated. Among the different silanes tested, γ-aminopropyltrimethoxysilane (APS) was found to be the best coupling agent for the glass fibers, possibly, because of its chemical compatibility with PA6. Tensile test results indicated that increasing amount of PA6 in the polymer matrix improved the strength and stiffness of the composites due to a strong acid–base interaction at the interface. Incorporation of PA6 to the SGF reinforced ABS reduced the melt viscosity, broadened the fiber length distributions and increased the toughness of the composites. Fractographic analysis showed that the incorporation of PA6 enhanced the interactions between glass fibers and the polymeric matrix.     

剑麻纤维/长玻纤混杂增强PP复合材料的力学性能研究

采用剑麻纤维(SF)和长玻璃纤维(LGF)混杂增强聚丙烯(PP)复合材料,考察了SF/LGF的比例和含量对PP复合材料力学性能的影响。结果表明:SF/LGF在聚丙烯树脂基体中呈交叉网状分布,这有利于提高复合材料的冲击强度、弯曲模量、拉伸强度和软化点。在SF/LGF质量比为2 2∶,二者总质量分数为30%时,SF/LGF混杂增强PP复合材料的综合力学性能较好。