Enhanced fatigue life of carbon nanotube‐reinforced epoxy composites

The effects of carbon nanotube (CNT) inclusion on cyclic fatigue behavior and the residual mechanical properties of epoxy composites after different degrees of fatigue have been studied. Tension–tension cyclic fatigue tests were conducted at various load levels (25–50 MPa) to establish the relationship between stress and the number of cycles to failure (S–N curves). The residual strength and modulus were measured after loading at 30 MPa for 5000, 15,000, and 25,000 cycles. The incorporation of a small amount of CNTs increased the fatigue life of epoxy in the high‐cycle, low‐stress‐amplitude regime by 1550%. Micrographs indicate the key mechanisms for enhancement in fatigue life such as CNT crack‐bridging and pullout. POLYM. ENG. SCI., 52:1882–1887, 2012. © 2012 Society of Plastics Engineers     

Electrical and mechanical properties of carbon nanotube‐epoxy nanocomposites

In this work, electrical conductivity and thermo‐mechanical properties have been measured for carbon nanotube reinforced epoxy matrix composites. These nanocomposites consisted of two types of nanofillers, single walled carbon nanotubes (SW‐CNT) and electrical grade carbon nanotubes (XD‐CNT). The influence of the type of nanotubes and their corresponding loading weight fraction on the microstructure and the resulting electrical and mechanical properties of the nanocomposites have been investigated. The electrical conductivity of the nanocomposites showed a significantly high, about seven orders of magnitude, improvement at very low loading weight fractions of nanotubes in both types of nanocomposites. The percolation threshold in nanocomposites with SW‐CNT fillers was found to be around 0.015 wt % and that with XD‐CNT fillers around 0.0225 wt %. Transmission optical microscopy of the nanocomposites revealed some differences in the microstructure of the two types of nanocomposites which can be related to the variation in the percolation thresholds of these nanocomposites. The mechanical properties (storage modulus and loss modulus) and the glass transition temperature have not been compromised with the addition of fillers compared with significant enhancement of electrical properties. The main significance of these results is that XD‐CNTs can be used as a cost effective nanofiller for electrical applications of epoxy based nanocomposites at a fraction of SW‐CNT cost. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical and thermal properties of functionalized multiwalled carbon nanotubes and multiwalled carbon nanotube–polyurethane composites

Multiwalled carbon nanotube (MWNT)–polyurethane (PU) composites were obtained by an in situ polycondensation approach. The effects of the number of functional groups on the dispersion and mechanical properties were investigated. The results showed that the functionalized MWNTs had more advantages for improving the dispersion and stability in water and N,N′‐dimethylformamide. The tensile strength and elongation at break of the composites exhibited obvious increases with the addition of MWNT contents below 1 wt % and then decreases with additions above 1 wt %. The maximum values of the tensile strength and elongation at break increased by 900 and 741%, respectively, at a 1 wt % loading of MWNTs. Differential scanning calorimetry measurements indicated that the addition of MWNTs resulted in an alteration of the glass‐transition temperature of the soft‐segment phase of MWNT–PU. Additionally, new peaks near 54°C were observed with differential scanning calorimetry because of the microphase‐separation structures and alteration of the segment molecular weights of the hard segment and soft segment of PU with the addition of MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of hyperbranched epoxy resin on mechanical properties of short carbon fiber‐reinforced epoxy composites

Short carbon fiber‐reinforced composites (SCFRCs) have attracted increasing attention owing to their comprehensive performance and easy processing route. However, the imperfect interfacial adhesion and serious stress concentration at the fiber/matrix interface have hampered their engineering application. In this article, we first report the preparation of SCFRC modified by a low‐viscosity liquid hyperbranched epoxy resin (Hyper E102). We then investigated the effect of Hyper E102 content on thermal and mechanical properties. The results show that the overall performance of the SCFRC first increases and then decreases with the increasing content of Hyper E102. With the incorporation of 12 phr Hyper E102, the tensile strength, fracture toughness, notched, and unnotched impact strength of SCFRC were increased by 16.7, 74.9, 95.3, and 194.5%, respectively. The toughening and reinforcing mechanisms were attributed to the following three aspects. First, the Hyper E102 improves the impregnation property of epoxy matrix against fibers, which helps form a better interfacial adhesion. Second, the incorporation of Hyper E102 reduces the internal stress level and stress concentration of the SCFRC. Finally, the critical crack length inside the SCFRC can be remarkably increased with the incorporation of Hyper E102, which can enhance the damage tolerance of a composite. POLYM. COMPOS., 37:2727–2733, 2016. © 2015 Society of Plastics Engineers     

Double‐wall carbon nanotube‐reinforced polyester nanocomposites: Improved dispersion and mechanical properties

Double‐walled carbon nanotube (DWCNT)‐reinforced polyester nanocomposites were prepared and tested to characterize their mechanical properties. The DWCNTs were functionalized to improve their dispersion within the polyester matrix. The improvement in the mechanical properties shows that the functionalized DWCNTs have better distribution within, and good adhesion with, the polyester matrix. A comparison of the mechanical properties of nanocomposites reinforced by functionalized and nonfunctionalized DWCNTs confirms that the functionalization leads to substantially improved composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Pseudoreinforcement effect of multiwalled carbon nanotubes in epoxy matrix composites

The carbon nanotube possesses outstanding physical properties. Theoretically, adding carbon nanotubes into a polymer matrix can remarkably improve the mechanical properties of the polymer matrix. In the present work, a series of composites was prepared by incorporating multiwalled carbon nanotubes (MWNTs) into an epoxy resin. The influences of MWNT content and curing temperature on the flexural properties of the epoxy resin were investigated. The results showed that a very low MWNT content should be used to ensure homogeneous dispersion of MWNTs in the epoxy matrix. A higher MWNT content may lead to deteriorated mechanical properties of the composites because of the aggregation of MWNTs. A decline in the flexural properties of the neat epoxy resin with increasing curing temperature was found. However, under the same curing conditions, improvement in flexural properties was observed for the composite with the low MWNT content and a mild curing temperature. The improvement was far beyond the predictions of the traditional short‐fiber composite theory. In fact, this improvement should be attributed to the retarding effect of MWNTs on the curing reaction of epoxy matrix. Therefore, the improvement in the flexural properties was only a pseudoreinforcement effect, not a nano‐reinforcement effect of the MWNTs on the epoxy resin. Perhaps, it is better for MWNTs to be used as functional fillers, such as electrical or thermal conductive fillers, than as reinforcements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3664–3672, 2006     

Dielectric properties of epoxy composites with modified multiwalled carbon nanotubes

We report here a high dielectric percolative polymer nanocomposite, fabricated by a combination of triethylene-tetramine (TETA) modified multiwalled carbon nanotube (named as TETA-MWNT) within epoxy resin matrix. In this composite system, with various TETA-MWNT volume fractions, the dielectric constant (K) is well fitted by the scaling law of the percolation theory with the percolation threshold f _c is 0.042 and the critical exponent p is 0.786. At 1,000 Hz of room temperature, the value of the dielectric constant is as high as 421 with the TETA-MWNT content of 4.14vol%, which is almost 60 times higher than that of epoxy resin. In contrast, a simple blend of pristine MWNT in epoxy composite shows evident lower dielectric constant and much higher loss with the same volume fraction.     

Thermal and mechanical properties of wood‐plastic composites filled with multiwalled carbon nanotubes

Wood plastic composites (WPCs) are a new generation of green composites which can come mostly from recycled materials. This study focuses on the thermal conductivity and mechanical properties of WPCs filled multiwalled carbon nanotubes (MWCNTs). The thermal conductivity increases with increasing amount of MWCNTs and decreases with increasing temperature. By comparing the temperature changes of specimens during heating and cooling processes, WPCs with higher MWCNTs contents presents higher average temperature when heated until equilibrium temperature. From differential scanning calorimeter test, the melting temperatures of MWNTs reinforced WPCs change slightly, but the crystallinity is reduced with the increasing amount of MWCNTs. Based on a series of laboratory experiments carried out to investigate the mechanical performance, it can be concluded that the addition of the MWCNTs decreases the mechanical properties of WPCs due to the decohesion between thermoplastic matrix and MWCNTs particles under stress. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46308.     

The effect of carbon nanotube hydrophobicity on the mechanical properties of carbon nanotube‐reinforced thermoplastic polyurethane nanocomposites

Double walled carbon nanotubes (DWNT) were functionalized by reacting methanol, dodecylamine, or octadecylamine with a toluene 2,4‐diisocyanate linker through a two‐stage reaction procedure. TGA coupled with FTIR analysis of both the decomposition products and the DWNT samples demonstrated that the functionalization procedure was successful and proceeded as expected for all samples. A preliminary investigation of the reinforcing capabilities of the functionalized DWNT in a thermoplastic polyurethane host polymer was then conducted. Tensile testing of the resultant nanocomposites demonstrated that the octadecylamine functionality provided the greatest enhancement in tensile strength and toughness. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Comparison of mechanical properties of epoxy composites reinforced with stitched glass and carbon fabrics: Characterization of mechanical anisotropy in composites and investigation on the interaction between fiber and epoxy matrix

The primary purpose of the study is to evaluate and compare the mechanical properties of epoxy‐based composites having different fiber reinforcements. Glass and carbon fiber composite laminates were manufactured by vacuum infusion of epoxy resin into two commonly used noncrimp stitched fabric (NCF) types: unidirectional and biaxial fabrics. The effects of geometric variables on composite structural integrity and strength were illustrated. Hence, tensile and three‐point bending flexural tests were conducted up to failure on specimens strengthened with different layouts of fibrous plies in NCF. In this article, an important practical problem in fibrous composites, interlaminar shear strength as measured in short beam shear test, is discussed. The fabric composites were tested in three directions: at 0°, 45°, and 90°. In addition to the extensive efforts in elucidating the variation in the mechanical properties of noncrimp glass and carbon fabric reinforced laminates, the work presented here focuses, also, on the type of interactions that are established between fiber and epoxy matrix. The experiments, in conjunction with scanning electron photomicrographs of fractured surfaces of composites, were interpreted in an attempt to explain the failure mechanisms in the composite laminates broken in tension. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Thermal and mechanical properties of carbon nanotube/epoxy nanocomposites reinforced with pristine and functionalized multiwalled carbon nanotubes

In this study, the effects of functionalization and weight fraction of mutliwalled carbon nanotubes (CNTs) were investigated on mechanical and thermomechanical properties of CNT/Epoxy composite. Epoxy resin was used as matrix material with pristine‐, COOH‐, and NH₂‐functionalized CNTs as reinforcements in weight fractions of 0.1, 0.5, and 1.0%. Varying (increasing) the weight fraction and changing type (pristine or functionalized) of CNTs caused increment in Young's modulus and tensile strength as observed during mechanical tests. CNT reinforcement improved thermal stability of the nanocomposites as observed by thermogravimetric analysis. Thermomechanical analysis showed a slight reduction in free volume of the polymer, that is a drop in coefficient of thermal expansion, prior to glass transition temperature (T_g) beside a slight increase in T_g value. Dynamic mechanical analysis indicated an increase in storage modulus and T_g owing to the strength addition of CNT to the matrix alongside the hardener. Scanning electron microscopy analysis of the fractured surface(s) revealed that CNTs were well dispersed with no agglomeration and resulted in reinforcing the matrix. POLYM. COMPOS., 36:1891–1898, 2015. © 2014 Society of Plastics Engineers     

Extension‐induced mechanical reinforcement in melt‐spun fibers of polyamide 66/multiwalled carbon nanotube composites

In this work, polyamide 66 (PA66) and its composites with multiwalled carbon nanotubes (MWNTs) were melt spun into fibers at different draw ratios. PA66 fibers at high draw ratio demonstrate a 40% increase in tensile strength, 66% increase in modulus and a considerable increase in toughness. It is demonstrated that this reinforcement can be mainly attributed to high‐draw‐ratio‐induced good dispersion and orientation of MWNTs, particularly the enhanced interfacial adhesion between MWNT and matrix thanks to interfacial crystallization. Our work provides a simple but efficient method to achieve good dispersion and strong interfacial interaction through melt spinning. Copyright © 2011 Society of Chemical Industry     

Mechanical behavior of carbon nanofibre‐reinforced epoxy composites

Epoxy resins are widely used in a variety of applications because of their high chemical and corrosion resistance and good mechanical properties. But few types of epoxy resins are brittle and possess low toughness which makes them unsuitable for several structural applications. In this work, carbon nanofibres have been dispersed uniformly into the epoxy resin at a very low concentration (0.07 vol. %). Improvement of 98% in Young modulus, 24% in breaking stress and 144% in work of rupture was achieved in the best sample. The emphasis is on achieving uniform dispersion of carbon nanofibers into epoxy resin using a combination of techniques such as ultrasonication, use of solvent and surfactants. The fracture surfaces of the specimens were studied under scanning electron microscope to see the fracture mechanism of nanocomposites under tensile load and correlate it to the enhancement in their properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of multiwalled carbon nanotubes on the processing behavior of epoxy powder compositions and on the mechanical properties of their fiber reinforced composites

This study reports the preparation of advanced carbon fiber composites with a nanocomposite matrix prepared by dispersing multiwall carbon nanotubes (CNTs) in a powder type epoxy oligomer with two different processing techniques (1) master batch dilution technique and (2) direct mixing (with the help of twin‐screw extruder in both cases). The master batch technique shows a better efficiency for the dispersion of the CNTs aggregates. The rheological results demonstrate that the incorporation of the CNTs into the epoxy oligomer leads, as expected, to a marked increase in the viscosity and of the presence of a yield stress point that also depends on the processing technique adopted. Carbon fiber (CFRP) and glass fiber (GFRP) composite materials were produced by electrostatic spraying of the epoxy matrix formulations on the carbon and glass fabric, respectively, followed by calendering and mold pressing. The mechanical properties of the obtained epoxy/CNT‐matrix composite materials, such as interlaminar fracture toughness, flexural strength, shear storage and loss moduli are discussed in terms of the processing techniques and fabric material. The incorporation of 1 wt% CNTs in the epoxy matrix results in a relevant increase of the fracture toughness, flexural strength and modulus of both CFRP and GFRP. POLYM. COMPOS., 37:2377–2383, 2016. © 2015 Society of Plastics Engineers     

Wedge test of carbon‐nanotube‐reinforced epoxy adhesive joints

Epoxy adhesives reinforced with carbon nanotubes (CNTs) were developed. The distribution of the CNTs in the epoxy matrix was observed with transmission electron microscopy. Joints were formed by unclad 2024‐T3 aluminum adherents bonded with the CNT‐filled epoxy adhesives. The durability of the joints was studied with a wedge test under water at 60°C. The addition of CNTs to the epoxy greatly improved the adhesive joint durability. The initial crack length of the joint with 1 wt % CNTs, which was obtained before the wedge specimen was put into water, was only about 7% of that with neat epoxy. After immersion of the specimens in 60°C water, the joint with neat epoxy failed after 3 h, but all of the joints adhered with different fractions of CNTs were still bound together after the experimental time of 90 h. The significant enhancement by CNTs of the adhesive joint durability was mainly attributed to the high mechanical properties of the CNTs and their ability to resist water. Nevertheless, the experimental results also reveal that the durability of the joints showed an optimum value at approximately 1 wt % CNTs, beyond which a decrease in the property was observed. In addition, the failure mechanism of the joints was also investigated in terms of interfacial failure and cohesive failure. Cohesive dominated failure was found for the joint bonded with 1 wt % CNT‐filled epoxy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

短碳纤维增强碳化硅基复合材料的制备

短纤维的分散均匀性一直是短纤维复合材料应用受限的主要原因．采用固相球磨分散和熔融渗硅工艺,可得到均匀分散的短碳纤维增强碳化硅基复合材料．并利用金相显微镜见察复合材料微观形貌,测试复合材料的抗弯强度和断后韧性．     

Effect of thermal fatigue on the mechanical properties of epoxy matrix composites reinforced with olive pits powder

This study is focused on the investigation of the effect of thermal shock cycling on the mechanical properties of cellulose based reinforced polymer composites. Polymer composites reinforced with olive pits powder at different filler‐volume fractions were manufactured. An increase in the bending modulus on the order of 48% was achieved. On the other hand, results showed that the bending strength remained almost unaffected from the amount of filler introduced. Next, the effect of thermal shock cycling on the mechanical behaviour of the thus manufactured composites was investigated. Theoretical predictions for both the properties variation with number of thermal shock cycles applied as well as with filler‐volume fraction were derived using the residual properties model (RPM) and the modulus predictive model (MPM), respectively. Predicted values were compared with respective experimental results. In all cases, a fair agreement between experimental findings and theoretical predictions was found. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Dynamic mechanical properties of some epoxy matrix composites

Dynamic mechanical properties of some epoxy matrix composites have been studied, comparing experimental data with theoretical models. The matrix in all composite samples was Shell Epon 828, a diglycidyl ether of bisphenol A, cured with meta-phenylenediamine. Fibrous composite samples were made with glass and graphite fibers. Particulate composite samples were made with glass microspheres, atomized aluminum, powdered silica, alumina, asbestos, mica, carbon black, and graphite. The dynamic elastic modulus and damping of these samples were measured at temperatures between 85° and 345°K by a free-free flexural resonance technique. The dynamic modulus of parallel fiber composites follows the linear rule of mixtures for low fiber volume fractions; deviations from linearity at higher volume fractions appear to be due to defects caused by the sample fabrication technique. Dynamic moduli of the particulate composites conform, within experimental error, to the static modulus theory of Wu up to filler volume fractions of 0.35 to 0.40. Deviations from Wu's theory at higher volume fractions may be due to agglomeration of filler particles. The damping of particulate composites with quasi-spherical filler particles appears to follow the rule of mixtures. In particulate composites with needle- and flake-type fillers, and in fibrous composites, the fillers are more highly stressed; with more of the strain energy in the low-damping fillers, overall damping is reduced. Damping greater than that attributable to the matrix and filler may be due to slippage at the interface between them. In addition to supporting Wu's theory of the elastic modulus of a particulate composite, this study demonstrates the utility of the nondestructive free-free flexural resonance techniques for obtaining a large body of reliable data in a short time from relatively few small samples. This greatly facilitates the experimental testing of theoretical models and the evaluation of fillers, matrix materials, and fabrication techniques.     

The effect of surface treatments on the mechanical properties of basalt‐reinforced epoxy composites

Basalt fiber is an emerging alternative reinforcement to glass or carbon depending upon the application. An important contributing parameter to ultimate performance of any composite is the fiber–‐matrix interface, to which toughness and compressive strength are intimately related. To better understand this matrix fiber interaction in controlling properties, we compared different modification strategies and the impact upon the properties of composites. Strategies focussing upon mechanical interlocking through increased surface roughness and covalent chemical bonding using sol/get methods were explored. Combined methods were also used to explore synergistic behavior as well as the use of aliphatic triethylenetetramine (TETA) to react with any covalently attached epoxy groups. Results from single ply composites showed that when the properties were fiber or fiber/matrix dominated, the sol/gel or epoxy silane method gave the largest improvement in ultimate tensile strength increasing 66% and 27% for uni‐weave 0° and 45° laminas. The combined surface modification methods exhibited increases of 45% and 13% for the same laminas. When properties were matrix dominated, the combined strategies produced the highest improvements in ultimate tensile strength of about 55% compared with 37% for sol/gel modification. For 16‐ply plain weave laminates, epoxy silane surface treatments produced the greatest improvements in compressive and interlaminar shear strengths, increasing 52% and 21%, respectively. This correlated with fiber‐ and fiber/matrix‐dominated results from single ply laminas. The combined treatment using TETA however decreased shear and compressive strength by about 20%, while scanning electron microscopy (SEM) evaluation and dynamic mechanical thermal analysis (DMTA) attributed this to increased resin ductility and plasticization. © 2013 Society of Plastics Engineers