Effect of packing pressure on fiber orientation in injection molding of fiber‐reinforced thermoplastics

Injection molding of fiber‐reinforced polymeric composites is increasing with demands of geometrically complex products possessing superior mechanical properties of high specific strength, high specific stiffness, and high impact resistance. Complex state of fiber orientation exists in injection molding of short fiber reinforced polymers. The orientation of fibers vary significantly across the thickness of injection‐molded part and can become a key feature of the finished product. Improving the mechanical properties of molded parts by managing the orientation of fibers during the process of injection molding is the basic motivation of this study. As a first step in this direction, the present results reveal the importance of packing pressure in orienting the fibers. In this study, the effects of pressure distribution and viscosity of a compressible polymeric composite melt on the state of fiber orientation after complete filling of a cavity is considered experimentally and compared with the simulation results of Moldflow analysis. POLYM. COMPOS. 28:214–223, 2007. © 2007 Society of Plastics Engineers     

Properties enhancement of short glass fiber‐reinforced thermoplastics via sandwich injection molding

This article demonstrates using sandwich injection molding in order to improve the mechanical properties of short glass fiber‐reinforced thermoplastic parts by investigating the effect of fiber orientation, phase separation, and fiber attrition compared to conventional injection molding. In the present case, the effect of short glass fiber content (varying from 0–40 wt%) within the skin and core materials were studied. The results show that the mechanical properties strongly depend not only on the fiber concentration, but also on the fiber orientation and the fiber length distribution inside the injection‐molded part. Slight discrepancies in the findings can be assumed to be due to fiber breakage occurring during the mode of processing. POLYM. COMPOS., 26:823–831, 2005. © 2005 Society of Plastics Engineers     

Measurement and numerical prediction of fiber‐reinforced thermoplastics' thermal conductivity in injection molded parts

Recent improvements in injection molding numerical simulation software have led to the possibility of computing fiber orientation in fiber reinforced materials during and at the end of the injection molding process. However, mechanical, thermal, and electrical properties of fiber reinforced materials are still largely measured experimentally. While theoretical models that consider fiber orientation for the prediction of those properties exist, estimating them numerically has not yet been practical. In the present study, two different models are used to estimate the thermal conductivity of fiber reinforced thermoplastics (FRT) using fiber orientation obtained by injection molding numerical simulation software. Experimental data were obtained by measuring fiber orientation in injection molded samples' micrographs by image processing methods. The results were then compared with the numerically obtained prediction and good agreement between numerical and experimental fiber orientation was found. Thermal conductivity for the same samples was computed by applying two different FRT thermal conductivity models using numerically obtained fiber orientation. In the case of thermal conductivity, predicted results were consistent with experimental data measurements, showing the validity of the models. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39811.     

Manufacturing and testing of long basalt fiber reinforced thermoplastic matrix composites

In this work, long basalt fiber reinforced composites were investigated and compared with short basalt fiber reinforced compounds. The results show that long fiber reinforced thermoplastic composites are particularly advantageous in the respects of dynamic mechanical properties and injection molding shrinkage. The fiber orientation in long basalt fiber reinforced products fundamentally differs from short basalt fiber reinforced ones. This results in more isotropic molding shrinkage in case of long basalt fiber reinforced composites. The main advantage of the used long fiber thermoplastic technology is that the special long fiber reinforced pellet can be processed by most conventional injection molding machines. During extrusion compounding the fibers in the compound containing 30 wt% fibers are fragmented to an average length of 0.48 mm (typical of short fiber reinforced thermoplastic compounds), this length decreases further during injection molding to 0.20 mm. Contrarily using long fiber reinforced pellets and cautious injection molding parameters, an average fiber length of 1.8 mm can be achieved with a conventional injection molding machine, which increased the average length/diameter ratio from 14 to 130. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

基于Mori⁃Tanaka方法的短纤维复合材料开孔板分析

基于Mori?Tanaka均匀化方法,对短纤维复合材料开孔板力学性能进行研究。首先,使用Mori?Tanaka方法预测单向和二维2种分布形式的短纤维复合材料应力?应变曲线曲线。其次,通过试验方法分析不同区域纤维取向对开孔板力学性能的影响。最后,使用多尺度方法研究不同注塑位置和不同开孔方式对开孔板力学性能的影响,该部分在宏观有限元分析中耦合了注塑模拟的纤维方向分布以及Mori?Tanaka均匀化方法得到的复合材料参数。结果表明,短边注塑开孔板综合力学性能更好;孔周围纤维分布是影响应力集中的主要因素;整体的纤维取向分布影响开孔板的刚度;单向纤维材料的角度对材料性能的影响不是单调的。     

Practical use of the statistically modified laminate model for injection moldings. Part 1: Method and verification

The fibers in injection molded FRP provide the material's strength and stiffness; however, they also supply many of the problems. Preferential orientation of fibers during molding can reduce strength and stiffness below expected values in critical directions, or induce warpage in thin walled sections. Makers of short fiber reinforced injection molded products typically use computer aided engineering packages to optimize product performance and manufacturing variables. However, the reliability of the fiber orientation simulation can be limited, and the method is not easily understood, making an assessment of accuracy for a given situation difficult. In addition, the structural module of flow analysis packages is often a basic package with many features missing. This paper presents a structural analysis system for injection molded parts made of short fiber reinforced plastics. A full-featured commercial structural analysis code is interfaced with a flow analysis program using a practical material model that takes into account the effects of local fiber orientation. The system is completely open to the user, and can be modified as required.     

Prediction of fiber orientation in a rotating compressing and expanding mold

In the rotating/compressing/expanding mold (RCEM), one mold wall can expand, compress, and rotate during injection molding, thus offering opportunities to control the thermomechanical history of a polymer and its microstructure. A computer simulation of flow and fiber orientation in RCEM was developed. The predictive model extends the generalized Hele‐Shaw formulation to account for compression/expansion and rotation of the mold wall, and uses the Folgar–Tucker model for fiber orientation predictions. A 20% GF polypropylene was molded under various molding conditions. The predicted fiber orientation distributions were compared with experiments. The model compares favorably with experiments, provided that the fiber orientation equation is modified by a strain‐reduction factor that slows the transient development of fiber alignment. The effect of fountain flow on orientation must also be included to correctly predict fiber orientation near the mold walls, mainly for the case of stationary and linear motions of the mold surface. Compression or expansion of the mold has only a small effect on fiber orientation, but rotation of the mold dramatically changes the orientation, causing fibers to align in the tangential direction across the entire thickness of the molding. This rotation action perturbs the fountain flow and becomes the dominant factor affecting fiber alignment across the entire cavity thickness. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Nonisothermal transient filling simulation of fiber suspended viscoelastic liquid in a center‐gated disk

The present study numerically investigates a fiber orientation in injection‐molded short fiber reinforced thermoplastic composite by using a rheological model, which includes the nonlinear viscoelasticity of polymer and the anisotropic effect of fiber in the total stress. A nonisothermal transient‐filling process for a center‐gated disk geometry is analyzed by a finite element method using a discrete‐elastic‐viscous split stress formulation with a matrix logarithm for the viscoelastic fluid flow and a streamline upwind Petrov–Galerkin method for convection‐dominated problems. The numerical analysis result is compared to the experimental data available in the literature in terms of the fiber orientation in center‐gated disk. The effects of the fiber coupling and the slow‐orientation kinetics of the fiber are discussed. Also, the effect of the injection‐molding processing condition is discussed by varying the filling time and the mold temperature. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers     

Effects of fiber orientation on strain concentrations in glass reinforced polyamides

Orientation of reinforcement fibers in injection molded parts is a key factor in determining their strength and stiffness: therefore stress-strain analyses based on isotropic material models produce only rough results. We present a flow/strain analysis methodology that accounts for the actual anisotropic material properties and fiber orientation. Material properties are determined by experiment, fiber orientation is inferred from flow simulation results (velocity vectors). Stress/strain fields are calculated by means of finite element analysis. Results show that for notched parts molded from short glass reinforced polyamide resin, there is a significant dependence of the strain concentration on the local fiber orientation resulting from different injection molding conditions.     

Injectin molding of short fiber reinforced thermoplastics in a center‐gated mold

We have studied injection molding of a rectangular box using short fiber reinforced polypropylene. The fiber orientation distribution and the local stiffness properties in radial and transverse directions have been measured in the bottom plane. The deduced orientation tensors are compared with predictions of a commercial computer code. Discrepancies are related to approximations made in the calculations and effects not accounted for by the present modeling approach. In the calculations the fiber interaction coefficient was varied seeking to fit experiments. We comment on the out‐of‐plane components of the orientation tensor, the relative thickness of skin and core layers, and the radial dependence of the fiber orientation in each layer. Values of the components of the 4^th‐order orientation tensor calculated from the measured orientation distribution are used to compare different closure approximations referred in the literature. Anisotropy in the stiffness properties, calculated form the measured fiber orientation, agree well with measurements.     

Short Fiber orientation and its Effects on the Properties of Thermoplastic Composite Materials

I. INTRODUCTION

While it is true that preform processes involving the use of long or continuous fibers are known and used in the manufacture of reinforced thermoplastic articles–Azdel [1] or STX sheet [2], for example–it is generally the case that such articles are formed by injection molding. Both the feedstock requirements for this process and the occurrence of high melt shear during it ensure that only short fibers will be present in the finished article. Although the use of slow screw speeds, slow injection rates, low back pressure, wide sprues, runners, and gates, and large radii of curvature avoids fiber breakage during molding, such conditions are not often found in practice. Furthermore, the necessity of incorporating reground material into the feedstock also ensures short fiber lengths in the final part, lengths not greatly in excess of the critical length required for effective stress transfer from polymer matrix to reinforcing fiber. In a practical part, design uncertainties caused by fiber length attrition are further compounded by the effects of fiber orientation. Although length distribution effects have been studied by a number of workers, both experimentally [3] and theoretically [4], relatively little has been reported on orientation effects in short fiber reinforced thermoplastics.     

Evaluation of molecular orientation in injection molded parts with microscale features by Raman spectroscopy

Molecular orientation of polycarbonate (PC) in injection‐molded parts with microscale features was characterized by means of polarized Raman spectroscopy, and the relationship between microstructure and replication was discussed. The microscale feature size of continuous v‐groove was 20 μm in depth and 50 μm in width. PC injection‐molded parts were molded with various molding conditions. The molecular orientation distribution along flow direction on the cross‐section of molding parts were evaluated by the intensity ratio of the bands at 635 to 703 cm^?1 (I₆₃₅/I₇₀₃) in the Raman spectra. Molecular orientation along the flow direction inside the v‐groove was higher than that of the core and the opposite surface region. In particular, the highest molecular orientation was at the surface of the v‐groove. Among the injection molding conditions, the mold temperature showed significant effect on the molecular orientation and replication. Higher mold temperature caused high replication and low molecular orientation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Numerical prediction of flake orientation and surface color in injection molding of flake‐pigmented thermoplastics

The present study attempts to develop physical modeling and numerical simulation system for prediction of the surface color in injection molding of flake‐pigmented thermoplastic composites. Folgar–Tucker model along with the orientation tensor is employed to predict the orientation state of pigment flakes. A phenomenological relationship between the orientation state and the surface color is proposed to estimate the surface color and color defects from the orientation prediction result. Basic studies are carried out using simple geometries with a hole or rib structure. Also a qualitative comparison between the numerical prediction and the experimental result is carried out for a complex geometry having ribs and holes. The color defects such as flow marks and weld lines could be reasonably predicted using the developed modeling and simulation system. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

A numerical simulation of short fiber orientation in compression molding

A computer simulation has been developed to predict the orientation of fibers in a thin, flat part that is compression molded from sheet molding compound. The simulation combines a finite element/control volume simulation of the mold filling flow, a second order tensor representation of the fiber orientation state and a finite element calculation for the transient orientation problem. Sample results and comparison with experiments are presented. Predictions compare favorably with experiments on SMC (sheet molding compound) plaques and a model suspension of nylon fibers and silicon oil.     

Fiber orientation and mechanical properties of short-fiber-reinforced injection-molded composites: Simulated and experimental results

A numerical simulation is presented that combines the flow simulation during injection molding with an efficient algorithm for predicting the orientation of short fibers in thin composite parts. Fiber-orientation state is represented in terms of a second-order orientation tensor. Fiber-fiber interactions are modeled by means of an isotropic rotary diffusion. The simulation predicts flow-aligned fiber orientation (shell region)near the surface with transversely aligned (core region) fibers in the vicinity of the mid-plane. The effects of part thickness and injection speed on fiber orientation are analyzed. Experimental measurements of fiber orientation in plaque-shaped parts for three different combinations of cavity thickness and injection speed are reported. It is found that gapwise-converging flow due to the growing layer of solidified polymer near the walls tends to flow-align the fibers near the entrance, whereas near the melt front, gapwise-diverging flow due to the diminishing solid layer tends to lign the fibers transverse to the flow. The effect of this gapwise-converging-diverging flow is found to be especially significant for thin parts molded at slower injection speeds, which have a proportionately thicker layer of solidified polymer during the filling process. If the fiber orientation is known, predictions of the anisotropic tensile moduli and thermal-expansion coefficients of the composite are obtained by using the equations for unidirectional composites and taking an orientation average. These predictions are found to agree reasonably well with corresponding experimental measurements.     

Fiber orientation in injection molding with rotating flow

The development of fiber orientation in injection molding was manipulated by a special molding tool, the RCEM mold, which imposes a rotation action by one of the cavity surfaces during the filling stage. Center‐gated disc moldings were produced from glass fiber reinforced polypropylene with different cavity rotation velocities, inducing distinct distributions and levels of fiber orientation. The morphologies of the moldings were characterized by optical and electronic microscopy. The through‐thickness profiles of fiber orientation were assessed by means of the orientation tensor, and the relationship between the processing thermo‐mechanical environment and the fiber orientation was established. At high rotation velocities, the resulting fiber orientation pattern is mainly controlled by the rotational motion, inducing a much more homogeneous through‐the‐thickness fiber orientation distribution, with a preferential alignment on the circumferential direction. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Combined effect of shear and nucleating agent on the multilayered structure of injection‐molded bar of isotactic polypropylene

Molten polymers are usually exposed to varying levels of shear flow and temperature gradient in most processing operations. Many studies have revealed that the crystallization and morphology are significantly affected under shear. A so‐called “skin‐core” structure is usually formed in injection‐molded semicrystalline polymers such as isotactic polypropylene (iPP) or polyethylene (PE). In addition, the presence of nucleating agent has great effect on the multilayered structure formed during injection molding. To further understand the morphological development in injection‐molded products with nucleating agent, iPP with and without dibenzylidene sorbitol (DBS) were molded via both dynamic packing injection molding (DPIM) and conventional injection molding. The structure of these injection‐molded bars was investigated layer by layer via SEM, DSC, and 2 days‐WAXD. The results indicated that the addition of DBS had similar effect on the crystal size and its distribution as shear, although the later decreased the crystal size more obviously. The combination of shear and DBS lead to the formation of smaller spherulites with more uniform size distribution in the injection‐molded bars of iPP. A high value of c‐axis orientation degree in the whole range from the skin to the area near the core center was obtained in the samples molded via DPIM with or without DBS, while in samples obtained via conventional injection molding, the orientation degree decreased gradually from the skin to the core and the decreasing trend became more obvious as the concentration of DBS increased. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rheological and mechanical behavior of long‐polymer‐fiber reinforced thermoplastic pellets

Polymer–polymer materials consist of a thermoplastic matrix and a thermoplastic reinforcement. Recent research activities concentrate on the manufacturing of semi‐finished polymer–polymer materials in other shapes than the commercially available tapes and sheets. In particular, a pellet‐like form provides the possibility of processing the polymer–polymer material by injection and compression molding. Nevertheless, the thermoplastic reinforcement is vulnerable to excessive heat and the processing usually needs special attention. The current study investigates the processing of long‐polymer‐fiber reinforced thermoplastic pellets, namely polypropylene‐polyethylene terephthalate and a single‐polymer polyethylene terephthalate, by extrusion for subsequent compression molding applications. The flow characteristics of the material as well as the preservation of the polymer reinforcement can be handled by accurate temperature control. The tensile and impact properties decrease with increasing process temperature though. Moreover, the results prove that the use of a common long‐fiber reinforced thermoplastic process chain is applicable to the newly developed polymer–polymer material. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39716.     

Integrated simulation to predict warpage of injection molded parts

Injection molding analysis programs were developed for CAE (Computer Aided Engineering) in injection molding of thermoplastics. The programs consist of mold cooling, polymer filling-packing-cooling, fiber orientation, material properties and stress analyses. These programs are integrated to predict warpage of molded parts by using a common geometric model of three dimensional thinwalled molded parts. The warpage is predicted from temperature difference between upper and lower surfaces, temperature distribution, flow induced shear stress, shrinkage, and anisotropic mechanical properties caused by fiber orientation in the integrated simulation. The integrated simulation was applied to predicting warpage of a 4-ribbed square plate of glass fiber reinforced polypropylene for examination of its validity. Predicted saddle-like warpage was in good agreement with experimental one.