Response analysis and comparison of a spar‐type floating offshore wind turbine and an onshore wind turbine under blade pitch controller faults

This paper analyses the effects of three pitch system faults on two classes of wind turbines, one is an onshore type and the other a floating offshore spar‐type wind turbine. A stuck blade pitch actuator, a fixed value fault and a bias fault in the blade pitch sensor are considered. The effects of these faults are investigated using short‐term extreme response analysis with the HAWC2 simulation tool. The main objectives of the paper are to investigate how the different faults affect the performance of wind turbines and which differences exist in the structural responses between onshore and floating offshore wind turbines. Several load cases are covered in a statistical analysis to show the effects of faults at different wind speeds and fault amplitudes. The severity of individual faults is categorized by the extreme values the faults have on structural loads. A pitch sensor stuck is determined as being the most severe case. Comparison between the effects on floating offshore and onshore wind turbines show that in the onshore case the tower, the yaw bearing and the shaft are subjected to the highest risk, whereas in the offshore case, the shaft is in this position. Copyright © 2014 John Wiley & Sons, Ltd.     

Open‐loop frequency response analysis of a wind turbine using a high‐order linear aeroelastic model

Wind turbine controllers are commonly designed on the basis of low‐order linear models to capture the aeroelastic wind turbine response due to control actions and disturbances. This paper characterizes the aeroelastic wind turbine dynamics that influence the open‐loop frequency response from generator torque and collective pitch control actions of a modern non‐floating wind turbine based on a high‐order linear model. The model is a linearization of a geometrically non‐linear finite beam element model coupled with an unsteady blade element momentum model of aerodynamic forces including effects of shed vorticity and dynamic stall. The main findings are that the lowest collective flap modes have limited influence on the response from generator torque to generator speed, due to large aerodynamic damping. The transfer function from collective pitch to generator speed is affected by two non‐minimum phase zeros below the frequency of the first drivetrain mode. To correctly predict the non‐minimum phase zeros, it is essential to include lateral tower and blade flap degrees of freedom. Copyright © 2013 John Wiley & Sons, Ltd.     

Aerodynamic simulations of offshore floating wind turbine in platform‐induced pitching motion

Forfloating offshore wind turbines, rotors are under coupled motions of rotating and platform‐induced motions because of hydrodynamics impacts. Notably, the coupled motion of platform pitching and rotor rotating induces unsteadiness and nonlinear aerodynamics in turbine operations; thus having a strong effect on the rotor performances including thrust and power generation. The present work aims at developing a computational fluid dynamics model for simulations of rotor under floating platform induced motions. The rotor motion is realized using arbitrary mesh interface, and wind flows are modelled by incompressible Navier‐Stokes flow solver appended by the k  ? ω shear stress transport turbulence model to resolve turbulence quantities. In order to investigate the fully coupled motion of floating wind turbine, the six degree of freedom solid body motion solver is extended to couple with multiple motions, especially for the motion of rotor coupled with the prescribed surge‐heave‐pitch motion of floating platform. The detailed methodology of multiple motion coupling is also described and discussed in this work. Both steady and unsteady simulations of offshore floating wind turbine are considered in the present work. The steady aerodynamic simulation of offshore floating wind turbine is implemented by the multiple reference frames approach and for the transient simulation, the rotor motion is realized using arbitrary mesh interface. A rigorous benchmark of the present numerical model is performed by comparing to the reported literatures. The detailed elemental thrust and power comparisons of wind turbine are carried out by comparing with the results from FAST developed by National Renewable Energy Laboratory and various existing numerical data with good agreement. The proposed approach is then applied for simulations of National Renewable Energy Laboratory 5MW turbine in coupled platform motion at various wind speeds under a typical load case scenario. Transient effect of flows over turbines rotor is captured with good prediction of turbine performance as compared with existing data from FAST. Copyright © 2016 John Wiley & Sons, Ltd.     

Assessment of a comprehensive aeroelastic tool for horizontal‐axis wind turbine rotor analysis

This paper presents the development of a computational aeroelastic tool for the analysis of performance, response and stability of horizontal‐axis wind turbines. A nonlinear beam model for blades structural dynamics is coupled with a state‐space model for unsteady sectional aerodynamic loads, including dynamic stall effects. Several computational fluid dynamics structural dynamics coupling approaches are investigated to take into account rotor wake inflow influence on downwash, all based on a Boundary Element Method for the solution of incompressible, potential, attached flows. Sectional steady aerodynamic coefficients are extended to high angles of attack in order to characterize wind turbine operations in deep stall regimes. The Galerkin method is applied to the resulting aeroelastic differential system. In this context, a novel approach for the spatial integration of additional aerodynamic states, related to wake vorticity and dynamic stall, is introduced and assessed. Steady‐periodic blade responses are evaluated by a harmonic balance approach, whilst a standard eigenproblem is solved for aeroelastic stability analyses. Drawbacks and potentialities of the proposed model are investigated through numerical and experimental comparisons, with particular attention to rotor blades unsteady aerodynamic modelling issues. Copyright © 2016 John Wiley & Sons, Ltd.     

Impact of mooring lines dynamics on the fatigue and ultimate loads of three offshore floating wind turbines computed with IEC 61400‐3 guideline

The calculation of loads for floating offshore wind turbines requires time‐domain integrated simulation tools where most of the physical concepts involved in the system dynamics are considered. The loads at the different components are used for the structural calculation and influence the design noticeably. This study quantifies the influence of mooring dynamic models on the calculation of fatigue and ultimate loads with integrated tools and compares its performance with a lower computational cost quasi‐static mooring model. Three platforms representing the principal topologies (spar, semisubmersible and tension‐leg platform) were assumed to be installed at the same 200 m depth location in the Irish coast. For each platform, the fatigue and ultimate loads were computed with an integrated floating wind turbine simulation code using both, a quasi‐static and a fully dynamic moorings model. More than 3500 simulations for each platform and mooring model were launched and post‐processed according to the IEC 61400‐3 guideline in an exercise similar to what a certification entity may require to an offshore wind turbine designer. The results showed that the impact of mooring dynamics in both fatigue and ultimate loads increases as elements located closer to the platform are evaluated; the blade and the shaft loads are only slightly modified by the mooring dynamics in all the platform designs; the tower base loads can be significantly affected depending on the platform concept; and the mooring lines tensions strongly depend on the lines dynamics, both in fatigue and extreme loads for all the platform concepts evaluated. Copyright © 2016 John Wiley & Sons, Ltd.     

Development of an aeroelastic code based on three‐dimensional viscous–inviscid method for wind turbine computations

Aerodynamic and structural dynamic performance analysis of modern wind turbines are routinely estimated in the wind energy field using computational tools known as aeroelastic codes. Most aeroelastic codes use the blade element momentum (BEM) technique to model the rotor aerodynamics and a modal, multi‐body or the finite‐element approach to model the turbine structural dynamics. The present work describes the development of a novel aeroelastic code that combines a three‐dimensional viscous–inviscid interactive method, method for interactive rotor aerodynamic simulations (MIRAS), with the structural dynamics model used in the aeroelastic code FLEX5. The new code, called MIRAS‐FLEX, is an improvement on standard aeroelastic codes because it uses a more advanced aerodynamic model than BEM. With the new aeroelastic code, more physical aerodynamic predictions than BEM can be obtained as BEM uses empirical relations, such as tip loss corrections, to determine the flow around a rotor. Although more costly than BEM, a small cluster is sufficient to run MIRAS‐FLEX in a fast and easy way. MIRAS‐FLEX is compared against the widely used FLEX5 and FAST, as well as the participant codes from the Offshore Code Comparison Collaboration Project. Simulation tests consist of steady wind inflow conditions with different combinations of yaw error, wind shear, tower shadow and turbine‐elastic modeling. Turbulent inflow created by using a Mann box is also considered. MIRAS‐FLEX results, such as blade tip deflections and root‐bending moments, are generally in good agreement with the other codes. Copyright © 2017 John Wiley & Sons, Ltd.     

Aeroelastic stability predictions for a MW‐sized blade

Classical aeroelastic flutter instability historically has not been a driving issue in wind turbine design. In fact, rarely has this issue even been addressed in the past. Commensurately, among the wind turbines that have been built, rarely has classical flutter ever been observed. However, with the advent of larger turbines fitted with relatively softer blades, classical flutter may become a more important design consideration. In addition, innovative blade designs involving the use of aeroelastic tailoring, wherein the blade twists as it bends under the action of aerodynamic loads to shed load resulting from wind turbulence, may increase the blade's proclivity for flutter. With these considerations in mind it is prudent to revisit aeroelastic stability issues for a MW‐sized blade with and without aeroelastic tailoring. Focusing on aeroelastic stability associated with the shed wake from an individual blade turning in still air, the frequency domain technique developed by Theodorsen for predicting classical flutter in fixed wing aircraft has been adapted for use with a rotor blade. Results indicate that the predicted flutter speed of a MW‐sized blade is slightly greater than twice the operational speed of the rotor. When a moderate amount of aeroelastic tailoring is added to the blade, a modest decrease (12%) in the flutter speed is predicted. By comparison, for a smaller rotor with relatively stiff blades the predicted flutter speed is approximately six times the operating speed. When frequently used approximations to Theodorsen's method are implemented, drastic underpredictions result, which, while conservative, may adversely impact blade design. These underpredictions are also evident when this MW‐sized blade is analysed using time domain methods. Published in 2004 by John Wiley & Sons, Ltd.     

Design and model confirmation of the intermediate scale VolturnUS floating wind turbine subjected to its extreme design conditions offshore Maine

Floating offshore wind turbines are gaining considerable interest in the renewable energy sector. Design standards for floating offshore wind turbines such as the American Bureau of Shipping (ABS) Guide for Building and Classing Floating Offshore Wind Turbine Installations are relatively new and few if any floating wind turbines have yet experienced the prescribed design extreme environmental conditions. Only a few pilot floating turbines have been deployed in Europe and Japan. These turbines have been designed for long return period storm events and are not likely to see their extreme design conditions during early deployment periods because of the low probability of occurrence. This paper presents data collected for an intermediate scale floating semi‐submersible turbine intentionally placed offshore Maine in a carefully selected site that subjects the prototype to scale extreme conditions on a frequent basis. This prototype, called VolturnUS 1:8, was the first grid‐connected offshore wind turbine in the Americas, and is a 1:8 scale model of a 6 MW prototype. The test site produces with a high probability 1:8 scale wave environments, and a commercial turbine has been selected so that the wind environment/rotor combination produces 1:8‐scale aerodynamic loads appropriate for the site wave environment. In the winter of 2013–2014, this prototype has seen the equivalent of 50 year to 500 year return period storms exercising it to the limits prescribed by design standards, offering a unique look at the behavior of a floating turbine subjected to extreme design conditions. Performance data are provided and compared to full‐scale predicted values from numerical models. There are two objectives in presenting this data and associated analysis: (i) validate numerical aeroelastic hydrodynamic coupled models and (ii) investigate the performance of a near full‐scale floating wind turbine in a real offshore environment that closely matches the prescribed design conditions from the ABS Guide. Copyright © 2015 John Wiley & Sons, Ltd.     

Time‐accurate blade surface static pressure behaviour on a rotating H‐Darrieus wind turbine

Time‐accurate blade pressure distributions on a rotating H‐Darrieus wind turbine at representative tip speed ratios during start‐up are presented here, which allow blade dynamic stall and laminar separation bubbles to be observed clearly and which provide a rare experimental demonstration of the flow curvature effect inherent in H‐Darrieus turbine operation. The convection of a dynamic stall vortex along the blade surface at high reduced frequency has also been clearly identified. This study provides new information of the complex aerodynamics of the vertical axis wind turbines (VAWTs) and provides unique experimental data to validate the transient blade static surface pressure distribution predicted by CFD models. To the best of the authors' knowledge, this is the first time that the instantaneous pressure variation around the blade has been measured and recorded directly for an H‐Darrieus wind turbine.     

Site‐specific Design Optimization of Wind Turbines

This article reports results from a European project, where site characteristics were incorporated into the design process of wind turbines, to enable site‐specific design. Two wind turbines of different concept were investigated at six different sites comprising normal flat terrain, offshore and complex terrain wind farms. Design tools based on numerical optimization and aeroelastic calculations were combined with a cost model to allow optimization for minimum cost of energy. Different scenarios were optimized ranging from modifications of selected individual components to the complete design of a new wind turbine. Both annual energy yield and design‐determining loads depended on site characteristics, and this represented a potential for site‐specific design. The maximum variation in annual energy yield was 37% and the maximum variation in blade root fatigue loads was 62%. Optimized site‐specific designs showed reductions in cost of energy by up to 15% achieved from an increase in annual energy yield and a reduction in manufacturing costs. The greatest benefits were found at sites with low mean wind speed and low turbulence. Site‐specific design was not able to offset the intrinsic economic advantage of high‐wind‐speed sites. It was not possible to design a single wind turbine for all wind climates investigated, since the differences in the design loads were too large. Multiple‐site wind turbines should be designed for generic wind conditions, which cover wind parameters encountered at flat terrain sites with a high mean wind speed. Site‐specific wind turbines should be designed for low‐mean‐wind‐speed sites and complex terrain. Copyright © 2002 John Wiley & Sons, Ltd.     

Stability analysis of pitch‐regulated,variable‐speed wind turbines in closed loop operation using a linear eigenvalue approach

A multi‐body aeroelastic design code based on the implementation of the combined aeroelastic beam element is extended to cover closed loop operation conditions of wind turbines. The equations of a controller for variable generator speed and pitch‐controlled operation in high wind speeds are combined with the aeroelastic equations of motion for the complete wind turbine, in order to provide a compound aeroservoelastic system of equations. The control equations comprise linear differential equations for the pitch and generator torque actuators, the control feedback elements (proportional–integral control) and the various filters acting on the feedback signals. In its non‐linear form, the dynamic equations are integrated in time to provide the reference state, while upon linearization of the system and transformation in the non‐rotating frame, the linear stability equations are derived. Stability results for a multi‐MW wind turbine show that the coupling of the controller dynamics with the aeroelastic dynamics of the machine is important and must be taken into account in view of defining the controller parameters. Copyright © 2008 John Wiley & Sons, Ltd.     

Indicial lift response function: an empirical relation for finite‐thickness airfoils,and effects on aeroelastic simulations

The aeroelastic response of wind turbines is often simulated in the time domain by using indicial response techniques. Unsteady aerodynamics in attached flow are usually based on Jones's approximation of the flat plate indicial response, although the response for finite‐thickness airfoils differs from the flat plate one. The indicial lift response of finite‐thickness airfoils is simulated with a panel code, and an empirical relation is outlined connecting the airfoil indicial response to its geometric characteristics. The effects of different indicial approximations are evaluated on a 2D profile undergoing harmonic pitching motion in the attached flow region; the resulting lift forces are compared with computational fluid dynamics (CFD) simulations. The relevance for aeroelastic simulations of a wind turbine is also evaluated, and the effects are quantified in terms of variations of equivalent fatigue loads, ultimate loads, and stability limits. The agreement with CFD computations of a 2D profile in harmonic motion is improved by the indicial function accounting for the finite‐thickness of the airfoil. Concerning the full wind turbine aeroelastic behavior, the differences between simulations on the basis of Jones's and finite‐thickness indicial response functions are rather small; Jones's flat‐plate approximation results in only slightly larger fatigue and ultimate loads, and lower stability limits. Copyright © 2012 John Wiley & Sons, Ltd.     

Aerodynamic shape optimization of wind turbine blades using a Reynolds‐averaged Navier–Stokes model and an adjoint method

Computational fluid dynamics (CFD) is increasingly used to analyze wind turbines, and the next logical step is to develop CFD‐based optimization to enable further gains in performance and reduce model uncertainties. We present an aerodynamic shape optimization framework consisting of a Reynolds‐averaged Navier Stokes solver coupled to a numerical optimization algorithm, a geometry modeler, and a mesh perturbation algorithm. To efficiently handle the large number of design variables, we use a gradient‐based optimization technique together with an adjoint method for computing the gradients of the torque coefficient with respect to the design variables. To demonstrate the effectiveness of the proposed approach, we maximize the torque of the NREL VI wind turbine blade with respect to pitch, twist, and airfoil shape design variables while constraining the blade thickness. We present a series of optimization cases with increasing number of variables, both for a single wind speed and for multiple wind speeds. For the optimization at a single wind speed performed with respect to all the design variables (1 pitch, 11 twist, and 240 airfoil shape variables), the torque coefficient increased by 22.4% relative to the NREL VI design. For the multiple‐speed optimization, the torque increased by an average of 22.1%. Depending on the CFD mesh size and number of design variables, the optimization time ranges from 2 to 24h when using 256 cores, which means that wind turbine designers can use this process routinely. Copyright © 2016 John Wiley & Sons, Ltd.     

A CFD study of coupled aerodynamic‐hydrodynamic loads on a semisubmersible floating offshore wind turbine

The prediction of dynamic characteristics for a floating offshore wind turbine (FOWT) is challenging because of the complex load coupling of aerodynamics, hydrodynamics, and structural dynamics. These loads should be accurately calculated to yield reliable analysis results in the design phase of a FOWT. In this study, a high‐fidelity fluid‐structure interaction simulation that simultaneously considers the influence of aero‐hydrodynamic coupling due to the dynamic motion of a FOWT has been conducted using computational fluid dynamics based on an overset grid technique. The DeepCwind semisubmersible floating platform with the NREL 5‐MW baseline wind turbine model is considered for objective numerical verification with the NREL FAST code. A state‐of‐the‐art computational model based on the coupled computational fluid dynamics and dynamic structure analysis is constructed and analyzed to solve multiphase flow, 6 degrees of freedom motions of OC4 semisubmersible FOWT. A quasi‐static mooring solver is also applied to resolve the constraint motion of floater because of a 3‐line mooring system. The influence of tower shadow on the unsteady aerodynamic performance and loads is also demonstrated. Finally, complex unsteady flow fields considering blade and tower interference effects among blade‐tip vortices, shedding vortices, and turbulent wakes are numerically visualized and investigated in detail.     

Aeroelastic design of large wind turbine blades considering damage tolerance

Modern offshore turbine blades can be designed for high fatigue life and damage tolerance to avoid excessive maintenance and therefore significantly reduce the overall cost of offshore wind power. An aeroelastic design strategy for large wind turbine blades is presented and demonstrated for a 100 m blade. High fidelity analysis techniques like 3D finite element modeling are used alongside beam models of wind turbine blades to characterize the resulting designs in terms of their aeroelastic performance as well as their ability to resist damage growth. This study considers a common damage type for wind turbine blades, the bond line failure, and explores the damage tolerance of the designs to gain insight into how to improve bond line failure through aeroelastic design. Flat‐back airfoils are also explored to improve the damage tolerance performance of trailing‐edge bond line failures. Copyright © 2016 John Wiley & Sons, Ltd.     

Rapid optimization of stall‐regulated wind turbine blades using a frequency‐domain method: Part 2, cost function selection and results

A fast and effective frequency‐domain optimization method was developed for stall‐regulated blades. It was found that when using linearized dynamics, typical cost functions employing damage‐equivalent root bending moments are not suitable for stall‐regulated wind turbines: when the cost function is minimized, the edgewise damping can be low, and the flapwise damping can approach zero during an extreme operating gust. A new cost function is proposed that leads to nicely balanced stall behavior and damping over the entire operating windspeed range. The method was used to design the blades of two multi‐MW, stall‐regulated, offshore wind turbines, comparable with the NREL 5 MW and NTNU 10 MW pitch‐regulated turbines. It is shown that the optimal stall‐regulated blade has a unique aerodynamic profile that gives high flapwise and edgewise damping and a uniform mean power output above the rated windspeed. The blades are described in sufficient detail that they can be used in further aeroelastic analyses, to compare large stall‐regulated and pitch‐regulated turbines. Copyright © 2014 John Wiley & Sons, Ltd.     

Wave‐current interaction effects on structural responses of floating offshore wind turbines

This paper proposes a model considering the wave‐current interactions in dynamic analyses of floating offshore wind turbines (FOWTs) and investigates the interaction effects on the FOWT responses. Waves when traveling on current are affected by the current, leading to frequency shift and shape modification. To include such interactions in FOWT analysis, which has not been considered by the researchers till date, a nonlinear hydrodynamic model for multicable mooring systems is presented that is able to consider the cable geometric nonlinearity, seabed contact, and the current effect. The mooring model is then coupled with a spar‐type FOWT model that handles the structural dynamics of turbine blades and tower, aerodynamics of the wind‐blade interaction, and wave‐current effects on the spar. The analytical wave‐current interaction model based on Airy theory considering the current effect is used in the computation of flow velocity and acceleration. Numerical studies are then carried out based on the NREL offshore 5‐MW baseline wind turbine supported on top of the OC3‐Hywind spar buoy. Two cases, (1) when the currents are favorable and (2) when the currents are adverse, are examined. Differences of up to 15% have been observed by comparing the cable fairlead tension obtained excluding and including the wave‐current interactions. In particular, when irregular waves interact with adverse current, a simple superposition treatment of the wave and the current effects seems to underestimate the spar motion and the cable fairlead tension. This indicates that the wave‐current interaction is an important aspect and is needed to be considered in FOWT analysis.     

Characterization of the unsteady aerodynamics of offshore floating wind turbines

Large‐scale offshore floating wind turbines were first proposed in 1972 by Prof. William E. Heronemus at the University of Massachusetts. Since then, very little progress has been made in the deployment of these systems despite the significant advantages afforded by floating wind turbines, namely access to superior wind resources and increased placement flexibility. Aside from the large capital costs associated with construction, one of the most significant challenges facing offshore floating wind turbines is a limited simulation and load estimation capability. Many wind turbine aerodynamic analysis methods rely on assumptions that may not be applicable to the highly dynamic environment in which floating wind turbines are expected to operate. This study characterizes the unique operating conditions that make aerodynamic analysis of offshore floating wind turbines a challenge. Conditions that may result in unsteady flow are identified, and a method to identify aerodynamically relevant platform modes is presented. Operating conditions that may result in a breakdown of the momentum balance equations are also identified for different platform configurations. It is shown that offshore floating wind turbines are subjected to significant aerodynamic unsteadiness fixed‐bottom offshore turbines. Aerodynamic analysis of offshore floating wind turbines may require the use of higher‐fidelity ‘engineering‐level’ models than commonly in use today. Copyright © 2012 John Wiley & Sons, Ltd.     

A decoupling control strategy for wind turbine blades equipped with active flow controllers

The use of active controls has shown to be of substantial help in supporting the increasing size of wind turbines by reducing peak stresses and fatigue loads. In this respect, this paper proposes the use of intuitive frequency‐based control strategies for reducing loads in wind turbine blades equipped with multi‐input multi‐output (MIMO) active flow controllers. For that purpose, a loop‐shaping approach is considered for analysing the dynamic of actively controlled wind turbine blades. Preliminary aeroelastic simulations are carried out to validate the results. It is shown that the MIMO vibration control problem can effectively be decomposed into a number of decoupled single‐input single‐output control problems because of the strong correlation between the dominant aeroelastic blade dynamics and actuator deployments. As a result, it is demonstrated that classical single‐input single‐output control systems can perform as efficiently as MIMO controllers for damping the aeroelastic dynamics of wind turbine blades. Copyright © 2016 John Wiley & Sons, Ltd.     

Impact of fault ride‐through requirements on fixed‐speed wind turbine structural loads

The emphasis in this article is on the impact of fault ride‐through requirements on wind turbines structural loads. Nowadays, this aspect is a matter of high priority as wind turbines are required more and more to act as active components in the grid, i.e. to support the grid even during grid faults. This article proposes a computer approach for the quantification of the wind turbines structural loads caused by the fault ride‐through grid requirements. This approach, exemplified for the case of a 2MW active stall wind turbine, relies on the combination of knowledge from complimentary simulation tools, which have expertise in different specialized wind turbines design areas. Two complimentary simulation tools are considered i.e. the detailed power system simulation tool PowerFactory from DIgSILENT and the advanced aeroelastic computer code HAWC2, in order to assess of the dynamic response of wind turbines to grid faults. These two tools are coupled sequently in an offline approach, in order to achieve a thorough insight both into the structural as well as the electrical wind turbine response during grid faults. The impact of grid requirements on wind turbines structural loads is quantified by performing a rainflow and a statistical analysis for fatigue and ultimate structural loads, respectively. Two cases are compared i.e. one where the turbine is immediately disconnected from the grid when a grid fault occurs and one where the turbine is equipped with a fault ride‐through controller and therefore it is able to remain connected to the grid during the grid fault. Copyright copy; 2010 John Wiley & Sons, Ltd.