Compact wideband bandpass filter with equiripple response in both magnitude and delay

Aiming at the reduction of the in‐band delay variation, a wideband bandpass filter with equiripple response in both magnitude and group delay is presented and studied. The filter is composed of one section of end‐connected coupled line and two short‐circuited shunt transmission line stubs, all of them are uniform and equal in electrical length. Design formulas are given to calculate the characteristic impedances of the lines to meet the filtering specifications. By changing the coupling strength of the coupled line section, the group delay can be controlled to be equiripple in band, while the remaining equiripple response in magnitude unchanged. For verification, a filter sample is fabricated and measured. In experiment, it exhibits a delay variation of 0.11 ns and minimal insertion loss of 0.2 dB within its passband (|S₁₁| < ?14 dB) from 0.48 to 1.46 GHz, which validates the theoretical predictions.     

Wideband and spurious‐suppressed differential bandpass filter based on strip‐loaded slot‐line structure

In this article, a wideband and spurious‐suppressed differential bandpass filter based on strip‐loaded slot‐line structure is presented. By means of the differential microstrip‐slot‐line‐microstrip transition, the proposed filter has a wideband bandpass filtering response. Simultaneously, the utilization of the strip‐loaded slot‐line extends its upper stop‐band. The proposed bandpass filter has wider upper‐stopband, wideband bandpass response, and intrinsic high common‐mode (CM) suppression. To verify the design concept, one filter example has been designed, fabricated, and measured. It has a differential‐mode (DM) 3‐dB fractional bandwidth of 157% with a low 0.82 dB minimum insertion loss. What's more, it shows a very wide 20 dB DM stop‐band bandwidth of 6.5 f_0d. The experienced results are in good agreement with the theoretical and simulated results.     

Spoof surface plasmon polariton band‐stop filter with single‐loop split ring resonators

A novel band‐stop filter with single‐loop split ring resonators (SRRs) is proposed for spoof surface plasmon polaritons (SPPs) at millimeter wave frequencies, achieving a miniaturized size of 0.052λ₀ × 0.278λ₀ at its resonant frequency. The SRRs provide both a low‐pass response as the rectangular corrugations used in the conventional SPPs and an additional band‐stop response induced by the resonance of SRRs. To verify this design, a back‐to‐back device with two coplanar waveguides as the input and output feeding was fabricated and characterized, the measured S‐parameters of which agree well with the simulation. The measured stop band is centered at 49 GHz with a ?10‐dB bandwidth of 4.1 GHz and a high Q‐factor of 93, in which the maximum attenuation is 31 dB. The filter has a low insertion loss of less than 2.8 dB in the pass band. Such approaches may find many applications to achieve compact millimeter wave circuits.     

Novel configuration of ultra‐wide band uni‐planar configuration of complementary split ring resonator composite right/left‐handed based band pass filter with sharp roll off and good stopband attenuation

In this paper, a compact novel simple design of ultra‐wide bandpass filter with high out of band attenuation is presented. The filter configuration is based on combining an ultra‐wide band composite right/left‐handed (CRLH) band pass filter (BPF) with simple uni‐planar configuration of complementary split ring resonator (UP‐CSRR). By integrating two UP‐CSRR cells, the ultra‐wideband CRLH filter roll‐off and wide stopband attenuation are enhanced. The filter has 3 dB cutoff frequencies at 3.1 GHz and 10.6 GHz with insertion loss equals 0.7 dB in average and minimum and maximum values of 0.48 dB and 1.05 dB, respectively over the filter passband. Within the passband. The transition band attenuation from 3 dB to 20 dB is achieved within the frequency band 1.9 GHz to 3.1 GHz (48%) at lower cutoff and the frequency band 10.6 GHz to 11.4 GHz (7%) at upper stopband. Moreover, the filter has a wide stopband attenuation >20 dB in frequencies 11 GHz to 13.6 GHz (21%) and ends with 3 dB cutoff frequency at 14.8 GHz. Furthermore, the designed filter size is very compact (23 × 12 mm²) whose length is only about 0.17 λ_g at 6.85 GHz. The filter performance is examined using circuit modeling, full‐wave simulations, and experimental measurements with good matching between all of them.     

A compact reconfigurable bandpass/lowpass filter with independent transmission zeros based on generalized NRI metamaterial

This article introduces a new design and analysis of a compact reconfigurable bandpass/lowpass filter based on compact negative refractive index metamaterial transmission line. The filter equivalent circuit has been designed as a cascade of three cells of bisected‐Π/Π configuration. The reconfigurable function was achieved using inserted switches in ON and OFF modes within the cells. The filter works as bandpass when all switches are in ON condition and for lowpass switch‐1 is in OFF and switch‐2 in ON condition. The low pass filter has 3‐dB cutoff frequency of 3.25 GHz with a selectivity of 170 dB/GHz. The bandpass filter is cantered at 3.65 GHz and has a well‐matched pass band with insertion loss of 0.2 dB and wide stop band with two transmission zeros (TZs). The frequency positions of TZs are independently varying with series and shunt loading elements. The filter performance has been validated through circuit model, electromagnetic simulation, and experimental measurements. The electrical size of bandpass filter excluding feed line is 0.22 λ_g × 0.20 λ_g (12 × 11 mm²) at center frequency of 3.65 GHz and for lowpass filter is 0.19 λ_g × 0.18 λ_g at cutoff frequency of 3.25 GHz. The filter can be applied in suitable for different wireless applications.     

Compact tri‐notched ultrawideband bandpass filter design using CSRR,DGS, and FMRR configurations

The folded multiple‐mode resonators with complementary split ring resonator (CSRR), and defected ground structures (DGS) are introduced for notched ultrawideband (UWB) bandpass filter (BPF) design in this article. Using the CSRR, FMRR, notched wide‐band BPF, a notch response can exist in the UWB passband for blocking the interference. Adjusting the size factor of CSRR, the wide tuning ranges of notch frequencies included the desired frequencies of 5.2/5.8 GHz are achieved. The lower insertion loss (0.31 dB), higher rejection level (?48.40 dB), wider bandwidth (FBW 75%), and wider stopband (extended to 2.01 f₀ below ?20 dB rejection level) of UWB band at the central frequency f₀ = 4.58 GHz are obtained. Second, design a CSRR, DGS, FMRR, tri‐notched UWB filter, the wider bandwidth (3.1–9.8 GHz) with FBW = 126%, lower insertion loss (0.26 dB), and higher rejection level (?44 dB) of UWB band at central frequency f₀ = 5.6 GHz are presented. Using the CSRR and interdigital couple, three notch responses can exist in the UWB passband for blocking the interference signals. Adjusting the size factor of CSRR and interdigital couple, the wide tuning ranges of notch frequencies included the desired frequencies of 5.18/6.10/8.08 GHz are achieved. The wide tuning ranges of three notched frequencies cover from 5.0 to 8.4 GHz. It is a simple way to control the notch responses. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:571–579, 2014.     

Exponential H∞ filter design for stochastic time‐varying delay systems with Markovian jumping parameters

In this paper, the exponential H_∞ filter design problem is investigated for a general class of stochastic time‐varying delay system with Markovian jumping parameters. The stochastic uncertainties appear in both the dynamic and the measurement equations and the state delay is assumed to be time‐varying. Attention is focused on the design of mean‐square exponentially stable and Markovian jump filter such that the filtering error systems are mean‐square exponentially stable and the estimation error satisfies a given H_∞ performance. By introducing some slack matrix variables, delay‐dependent sufficient conditions for the solvability of the above problem are presented in terms of linear matrix inequalities (LMIs). In addition, the decay rate can be a given positive value without any other constraints. When the proposed LMIs are feasible, an explicit expression of the desired H_∞ filter can be given. A numerical example is provided to illustrate the effectiveness of the proposed design approach. Copyright © 2009 John Wiley & Sons, Ltd.     

Compact ultra‐wideband bandpass filter with configurable stopband based on diamond‐shape resonator

An ultra‐wideband compact bandpass filter (BPF) with configurable stopband by tuning transmission zeroes is proposed in this paper. The ultra‐wideband bandpass response is based on a diamond‐shape resonator consisting of a pair of broadside coupled diamond‐shape microstrip lines, within which a diamond shape defected ground structure (DGS) is etched in the middle. Flexible transmission zeros realized by open and short stubs can be easily adjusted to improve band selectivity and harmonic suppression. Measurement result shows that the dedicated device has a 3 dB fractional bandwidth of 148% (0.94‐6.36 GHz) with 20 dB rejection stopband from 6.87 to 9.7 GHz (77.5%) which agrees good with the simulate performance. The overall size of the proposed BPF is 0.27 λ_g × 0.23 λ_g.     

Five‐order narrow‐band tunable superconducting filter

This article designed a five‐order narrow‐band tunable superconducting filter. The superconducting microstrip circuit was loaded by varactors diode. The center frequency of the tunable can be tuned through the changing of the bias voltage added in the varactors diode. The whole device has a parallel coupling structure and the filter circuit was fabricated by DyBa₂Cu₃O₇ superconducting film with 0.5 mm thickness and 2 in. LaAlO₃ as the substrate. The frequency can be continuously adjusted from 235 MHz to 250 MHz. The insertion loss of the filter was in the range of 2.51 dB to 9.64 dB. The bandwidth of the tunable filter was in the range of 0.5 MHz to 0.9 MHz. The out‐of‐band rejection was better than 70 dB. The measured results are in good agreement with the simulated ones.     

A dual‐band superconducting filter with a large bandwidth ratio

In this study, we propose a stepped‐impedance‐stub loaded interdigital capacitor resonator for design of a dual‐band band‐pass filter with a large bandwidth ratio. The presented resonator has strong and weak couplings in the upper passbands (UPs) and lower passbands (LPs), respectively, so as to form a large upper/lower bandwidth ratio. Adopting a dual‐branch phase‐matched feedline structure can meet the external quality factors required for the UP/LP. Therefore, these two passbands, defined by their respective center frequencies and bandwidths, can be manipulated independently. A four‐pole dual‐band example filter with a lower bandwidth of 20 MHz at 1576 MHz and an upper bandwidth of 200 MHz at 2450 MHz is successfully designed on an YBCO/MgO superconducting wafer. The filter exhibits excellent frequency responses. The upper/LPs show insertion losses below 0.07/0.22 dB and return losses above 15.3/15.3 dB. The stopband rejection is better than 57 dB until the first spurious passband up to 6150 MHz (3.9f_L).     

Compact ultra‐wideband bandpass filter with variable notch characteristics based on transversal signal‐interaction concepts

A novel technique is presented to design highly compact microstrip ultra‐wideband (UWB) bandpass filters that exhibit high selectivity quasi‐elliptical response. The design is based on transversal signal‐interaction concepts that enable the inclusion of single or dual notch‐bands within the filter's passband to eliminate interference from other services that coexist within the UWB spectrum. The filter configuration comprises of two transmission paths which include folded T‐shaped stepped impedance resonators (SIRs) that are capacitively coupled with the input/output lines to enable signal transmission. It is shown that by combining the filters of different passband centre frequencies an UWB filter can be realised with either a single‐ or dual‐notch function. The theoretical performance of the filter is corroborated via measurements to confirm that the proposed filter exhibits UWB passband of 123% for a 3 dB fractional bandwidth, a flat group‐delay with maximum variation of less than 0.3 ns, passband insertion loss less than 0.94 dB, high selectivity, a sharp rejection notch‐band with attenuation of ?23 dB, and a good overall out‐of‐band performance. Furthermore, the filter occupies a significantly small area of 94 mm² compared with its classical counterparts. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:549–559, 2014.     

Coupled‐line band‐pass filter with T‐shaped structure for high frequency selectivity and stopband rejection

A coupled‐line band‐pass filter (BPF) with T‐shaped stub structure is presented. Five transmission poles within the passband and eight deep transmission zeros (TZs) from 0 to 2f₀ (f₀ denotes filter's center frequency) are realized through input impedance calculations. With the simple T‐shaped structure, the positions of six TZs can be appropriately adjusted to achieve high frequency selectivity and stopband rejection. For demonstration, a BPF prototype centered at 2.05 GHz is designed and fabricated, whose measured rejection levels are of over 45.5 dB at lower stopband and better than 19.5 dB at upper stopband. The simulation and measurement results are in good agreement, which validates the design idea.     

High gain flexible liquid crystal polymer based 8‐element printed antenna for millimetric wave applications

In this article, an offset fed printed dipole antenna 2‐element, 4‐element, and 8‐element arrays are developed and analyzed for millimeter wave applications. The 8‐element array antenna is of compact size with dimensions 43.6 × 25.1 × 0.25 mm³. It achieved a broad impedance bandwidth (S₁₁ < ?10 dB) of 15.7 GHz from 24.7 to 40.4 GHz. The mutual coupling between array elements is less than ?35 dB in the operating band. The antenna achieved a gain of 12.62 to 13.1 dB. The 8‐element array antenna is fabricated on liquid crystal polymer material and tested. Impedance matching, far field radiation characteristics, co‐polarized and cross‐polarized patterns and group delay are analyzed in simulation and experimental measurement. The investigated results are in good agreement and hence, the developed array antenna is attractive for wideband millimeter wave applications.     

High inter‐port isolation dual circularly polarized slot antenna with interdigital capacitor

A planar dual circularly polarized slot antenna is presented. The designed antenna has two tilted “8” shaped slots fed by microstrip lines, one each for transmission (T_X) and reception (R_X) operations. The isolation between the two ports (T_X and R_X) is augmented by means of an interdigital capacitor based bandstop filter. The proposed antenna has an impedance bandwidth of 361 MHz centered at 2.293 GHz (2.113‐2.474 GHz) with the isolation between the ports being >17.6 dB which goes up to a value as high as 46 dB within the band of operation. The 3 dB axial ratio (AR) bandwidth is 11.52% centered at 2.1275 GHz (2.005‐2.25 GHz). Because of its high inter‐port isolation within the AR bandwidth, the design is suitable as a full‐duplex antenna for applications in S‐band.     

Widely separated dual‐band half‐mode SIW bandpass filter

A novel half‐mode substrate integrated waveguide (HMSIW) based dual‐band bandpass filter (DBBPF) is proposed. Back to back connected two defected ground structure (DGS) resonators on the top layer of HMSIW cavity constitute the passband with two transmission zeros (TZs) at a lower frequency. The higher modes TE₃₀₁ and TE₃₀₂ of HMSIW cavity give the passband response at higher frequency using the mode shifting technique with slot perturbation. The source‐load coupling has been used to create finite frequency TZs to improve the selectivity of the second passband. Therefore, the proposed filter gives two widely separated passbands, center frequencies (CFs) at 5.83 and 18.1 GHz with an attenuation of greater than 10 dB between the passbands. The synthesized filter is fabricated using a low‐cost single layer PCB process, and the measured S‐parameters are almost mimic the EM‐simulation results.     

Event‐triggered filter design for Markovian jump delay systems with nonlinear perturbation using quantized measurement

This paper deals with the problem of mixed passivity and H_∞ filter design for a class of Markovian jump delay systems with nonlinear perturbation under event‐triggered scheme and quantization. Firstly, based on an integral inequality, a new sufficient condition for the stochastic stability and performance analysis of the filtering error system is proposed. Secondly, a mode‐dependent condition for the solvability of the filter design problem is given in terms of linear matrix inequalities (LMIs). The filter parameters can be derived using feasible solutions of the presented LMIs. Finally, three numerical examples are given to illustrate the effectiveness and advantages of the proposed filter design method.     

A wideband circularly polarized slot antenna with antipodal strips for WLAN and C‐band applications

A single‐fed circularly polarized square shaped wide slot antenna with modified ground plane and microstrip feed has been presented. The field in the slot is perturbed by introducing an antipodal strips section attached with a microstrip line to produce circular polarization in a wide band of frequencies. The antipodal strip section consists of a group of four strips of unequal length and separation. The presence of asymmetric perturbations in the slot is mainly responsible for exciting two orthogonal modes in the slot having equal magnitude and 90° phase difference which results in circular polarization. A wide bandwidth of 3.3 GHz (4.4 GHz‐7.7 GHz) has been achieved for an axial ratio value AR < 3 dB with the minimum axial ratio value being 0.3 dB. The impedance bandwidth for |S₁₁| < ?10 dB ranges from 4.3 GHz to 8 GHz, and therefore covers most of the C‐band communication systems. The antenna exhibits stable radiation patterns throughout the circular polarization bandwidth with a gain around 6 dBi in entire operational bandwidth. A prototype of antenna was fabricated and measured. The antenna has a planar size 0.40λ₀ × 0.40λ₀ and thickness of 0.02λ₀ where λ₀ is the wavelength in free space at the lowest frequency. With its compact size and low profile, the antenna is a favorable choice for WLAN (5.15‐5.85 GHz) and a wide variety of C‐band wireless applications.     

A compact uniplanar ultra‐wideband frequency selective surface for antenna gain improvement and ground penetrating radar application

A simple structured single layered frequency selective surface (FSS) that has unit cell size of 11 × 11 mm², substrate thickness of 0.8 mm only and capable to work in a very widespread band from 0.001 to more than 17 GHz is proposed in this article. The FSS is competent to augment the gain of a UWB monopole antenna by 2 to 3.5 dBi when integrated at the back of antenna. The performances of “antenna‐FSS” structure is evaluated by simulation and experimental measurement where good correlations are obtained. The integrated structure provides wide impedance band (S₁₁ < ?10 dB) from 2.82 to 19.94 GHz (more than 150%) with improved broadside radiation and high radiation efficiency profile. The transient and frequency domain characteristics of “antenna‐FSS” composite structure are also evaluated in close proximity of diverse sub‐surfaces such as dry sand, wet sand, wood and concrete where an almost unaltered impedance band profile, linear transfer function response and non‐varying group delay responses are achieved which establishes the applicability of the composite structure in ground penetrating radar for low depth sub‐surface scanning applications.     

A self‐packaged wideband filtering power divider based on substrate‐integrated suspended line

In this study, a filtering power divider (FPD) is proposed by utilizing one T‐shaped tri‐mode stepped‐impedance resonator with input/output coupling structures based on substrate‐integrated suspended line (SISL). The circuit topology and SISL technology are combined together to reach balance in performances such as compact size, wideband, high frequency selectivity, low loss, good in‐band isolation, wide stopband, and self‐packaging so that there are no obvious flaws. Wide bandwidth and two near‐band transmission zeros are contributed by the proposed circuit topology. Good isolation can be obtained by comparing different coupling schemes with one resistor. An additional transmission zero for extending the upper stopband can be achieved by the two closely placed stubs without increasing the size of the design. Low loss and self‐packaging can be realized by SISL technology. For demonstration, a prototype is implemented with the size of 0.5λ_g × 0.28λ_g, which exhibits the 1‐dB fractional bandwidth of 26.3%, the frequency selectivity of 0.25/0.37 at the lower/upper edges of the passband, and the insertion loss of 1.1 dB (including transition) at the center frequency (f₀) of 3.34 GHz, while the in‐band isolation is higher than 20 dB and the 15‐dB stopband is achieved up to 3.74 f₀.     

A bandpass filter using asymmetric stepped‐impedance resonators and symmetric T‐shape interdigital capacitor structures with wide out‐of‐band rejection

In this study, a novel stepped impedance resonator (SIR) is proposed. This SIR is composed of two stepped impedance transmission‐lines and an interdigital capacitor structure. The proposed resonator has a high ratio of the first spurious frequency f_s to the fundamental frequency f₀ and is suitable to design wide stopband filters. An equivalent model is used to analyze the resonant properties of the resonator. The design guidelines of the proposed resonator are summarized. Moreover, the coupling properties of the resonator are simulated and analyzed. Finally, a small high‐temperature superconducting bandpass filter is designed and fabricated using the proposed SIRs. The stopband of the filter is extended up to 4.0 f₀ and 3.5 f₀ with 30 and 60 dB out‐of‐band rejection levels, respectively.