A dual‐band superconducting filter with a large bandwidth ratio

In this study, we propose a stepped‐impedance‐stub loaded interdigital capacitor resonator for design of a dual‐band band‐pass filter with a large bandwidth ratio. The presented resonator has strong and weak couplings in the upper passbands (UPs) and lower passbands (LPs), respectively, so as to form a large upper/lower bandwidth ratio. Adopting a dual‐branch phase‐matched feedline structure can meet the external quality factors required for the UP/LP. Therefore, these two passbands, defined by their respective center frequencies and bandwidths, can be manipulated independently. A four‐pole dual‐band example filter with a lower bandwidth of 20 MHz at 1576 MHz and an upper bandwidth of 200 MHz at 2450 MHz is successfully designed on an YBCO/MgO superconducting wafer. The filter exhibits excellent frequency responses. The upper/LPs show insertion losses below 0.07/0.22 dB and return losses above 15.3/15.3 dB. The stopband rejection is better than 57 dB until the first spurious passband up to 6150 MHz (3.9f_L).     

A balanced dual‐band bandpass filter with a wide stopband and controllable differential‐mode frequencies and fractional bandwidths

In this article, a balanced microstrip dual‐band bandpass filter (BPF) is designed. The proposed filter is achieved by employing a microstrip U‐shape half‐wavelength resonator, a folded stub‐loaded resonator and balanced microstrip/slotline transition structures. The center frequencies and the fractional bandwidths of the two differential‐mode (DM) passbands can be controlled independently by changing the physical lengths of the two resonators and the gaps between each resonator, respectively. The balanced microstrip/slotline transition structures can achieve a wideband common‐mode (CM) suppression. Meanwhile, the DM passbands are independent from the CM responses, which significantly simplify the design procedure. In addition, a wide DM stopband is also realized. In order to validate the design strategies, a balanced dual‐band BPF centered at 2.57 and 3.41 GHz was fabricated and a good agreement between the simulated and measured results is observed.     

A balanced dual‐band BPF with independently controllable frequencies and bandwidths

A balanced second‐order dual‐band bandpass filter (BPF) with independently controllable center frequencies and bandwidths based on coupled stepped‐impedance resonators (SIRs) is designed in this article. To obtain a dual‐band differential‐mode (DM) response, two pairs of SIRs with different resonant frequencies are employed in the design. The bandwidths of the two DM passbands can be independently tuned by adjusting the coupling gaps and coupling lengths of the corresponding resonators. In addition, three transmission zeros are realized to enhance the selectivity of the DM passbands. The microstrip‐slotline transition structure is utilized to achieve a wideband common‐mode (CM) suppression. Moreover, the DM responses are independent of the CM ones, which significantly simplify the design procedure. Finally, a balanced dual‐band BPF is designed to validate the design method and a good agreement between the simulated and measured results is observed.     

Compact dual‐band bandpass filter and diplexer using hybrid resonant structure with independently controllable dual passbands

In this article, a compact dual‐band bandpass filter (BPF) is developed using a hybrid resonant structure, which consists of a microstrip stub‐loaded dual‐mode resonator and a slotline stub‐loaded dual‐mode resonator. These two resonators, both having two controllable resonant modes and one transmission zero (TZ), are analyzed and used to construct two desired passbands of a dual‐band BPF. Multiple TZs are generated by introducing a source‐load coupling, thus improving the selectivity of the passbands. Then, the dual‐band BPF is reshaped to configure a compact diplexer. The inherent TZs of the two proposed resonators are designed to improve the frequency property and port isolation of the diplexer. Finally, a dual‐band BPF and a diplexer with the lower and upper passbands centered at 2.45 and 3.45 GHz, respectively, are designed, fabricated, and measured to verify the proposed structure and method.     

A novel dual‐band bandpass filter using co‐directional split ring resonators with closely spaced passbands and wide upper stopband

In this article, interdigital capacitor loaded co‐directional split ring resonators (CDSRRs) and their dual‐band bandpass filter applications are proposed. The proposed resonator is formed by nested open loop resonators having open ends at the same place unlike conventional split ring resonators (SRRs). In addition, the inner open loop resonator has interdigital capacitor located between the open ends. The proposed resonator exhibits dual resonance behavior with a small center frequency ratio. Both of resonance frequencies can be controlled due to the changes in the interdigital capacitor and the electrical length of the outer resonator. A dual‐band microstrip bandpass filter is designed by using the proposed CDSRR. Two CDSRRs are used to obtain two poles in each passband. Overall electrical length of the designed filter is 0.23 λ_g × 0.14 λ_g (0.0329 λ_g²), where λ_g is the guided wavelength for the used substrate at the lowest passband center frequency of 1.8 GHz. A small center frequency is obtained by adjusting the second passband at 2.27 GHz. A very wide upper stopband, closely spaced passbands, low insertion losses and high selectivity at both passbands can be obtained by means of the proposed structure. The designed filter was also fabricated and tested. The measured results show a very good agreement with the predicted results.     

Dual‐band filter with high selectivity and wide stopband rejection

This article presents a highly selective dual‐passband filter based on stepped‐impedance‐resonator (SIR) and mixed electromagnetic coupling. First, the surface area of the filter is effectively reduced by the triangular topology. Second, four controllable transmission zeros are introduced by source‐load coupling feed and mixed electromagnetic, which increases the selectivity of the filter. Third, a perturbation structure is added to independently control the resonance points of each passband. Finally, the improved defect ground structure (DGS) is integrated to obtain wide stopband rejection. The measured S‐parameters are well agreement with the simulated results, which show that the center frequencies of the two passbands are 2.4 GHz and 5.2 GHz; and the passband insertion losses are 0.85 dB and 1.6 dB; and the relative bandwidths are 14.6% and 5.7%, respectively. Besides, the structure is with six transmission zeros, and 20 dB suppression for the third harmonic and the fourth harmonic are achieved. Compared with the traditional SIR double‐passband filter, this filter has many advantages, such as simple design, small size, small insertion loss, controllable frequency, high selectivity, and high spurious suppression.     

A tunable balanced dual‐band BPF with quasi‐independently controlled center frequency and bandwidth

In this paper, a balanced dual‐band bandpass filter (BPF) with high selectivity and low insertion loss performance is presented by employing stub loaded resonators (SLRs) and stepped impedance resonators (SIRs) into balanced microstrip‐slotline (MS) transition structures. The balanced MS transition structures can achieve a wideband common‐mode (CM) suppression which is independent of the differential‐mode (DM) response, significantly simplifying the design procedure. Six varactors are loaded into the resonators to achieve the electrical reconfiguration. The proposed balanced dual‐band BPF can realize quasi‐independently tunable center frequencies and bandwidths. A tuning center frequency from 2.48 to 2.85 GHz and a fractional bandwidth (20.16%‐7.02%) with more than 15 dB return loss and less than 2.36 dB insertion loss are achieved in the first passband. The second passband can realize a tuning center frequency from 3.6 to 3.95 GHz with more than 12 dB return loss and less than 2.38 dB insertion loss. A good agreement between the simulated and measured results is observed.     

Independently controllable dual‐band microstrip bandpass filter using quadruple‐mode stub‐loaded resonator

In this article, a quadruple‐mode stub‐loaded resonator (QM‐SLR) is introduced and its four modes are excited using a simple approach, which can provide a dual‐band behavior. By changing the length of the loaded stubs, independently tunable transmission characteristics of the proposed quadruple‐mode stub‐loaded resonator were extensively described for filter design. Moreover, microwave varactors were adopted to represent the length variation of the loaded stubs for the dual‐band tunability. The equivalent circuit modeling of the open stub with microwave varactor was given and discussed. Then, adopting the compact quadruple‐mode stub‐loaded resonator with three varactors, an independently controllable dual‐band bandpass filter (BPF) was designed, analyzed, and fabricated. Its separated bandwidths and transmission zeros can be tuned independently by changing the applying voltage of the microwave varactors. A good agreement between simulated and measured results verified the design methodology. The proposed filter possesses compact size, simple structure, and excellent dual‐band performances. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:602–608, 2016.     

Compact dual‐ and triband bandpass filter using frequency selecting coupling structure loaded stepped‐impedance resonator

This article presents two novel resonators, that is, frequency selecting coupling structure loaded stepped‐impedance resonator (FSCSLSIR) and π‐section loaded FSCSLSIR. The resonator behaviors and guidelines are given to design FSCSLSIR dual‐band bandpass filter (BPF) and π‐section loaded FSCSLSIR triband BPF. The proposed dual‐ and triband BPF have very compact sizes of 0.13 λ_gd × 0.06 λ_gd and 0.115 λ_gt × 0.074 λ_gt, respectively. Moreover, good return loss, low insertion loss, and high band‐to‐band isolation can be observed, and the proposed FSCSLSIR dual‐band BPF has an ultrawide stopband from 5.79 to 36 GHz. The experimental results are in good agreement with the simulations. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:427–435, 2015.     

A compact dual‐band superconducting filter with fine‐tuning coupling structure

A novel dual‐mode optimized patch capacitor loaded T‐type resonator is proposed for the design of a dual‐band filter (DBF). The resonator has its lowest even‐ and odd‐mode at the two expected passband frequencies and the first spurious mode far away from the passbands. For tuning of the two sets of coupling strengths for both passbands, open/shorted secondary coupling structures are introduced as a fine‐tuning coupling structure to increase/decrease the primary coupling strength. A four‐pole DBF with passbands centered at 2450 and 3500 MHz, respectively, is proposed and fabricated using the HTS material. The measured results of the filter indicate superior performance and good fitting with the simulation results. The return losses of both passbands and the insertion losses obtained by measurements are greater than 14 dB and less than 0.3 dB, respectively. The stopband rejection exceeds 50 dB up to 8.0 GHz.     

New multi‐standard dual‐wideband and quad‐wideband asymmetric step impedance resonator filters with wide stop band restriction

New multi‐standard wide band filters with compact sizes are designed for wireless communication devices. The proposed structures realize dual‐wideband and quad‐wideband characteristics by using a new skew‐symmetrical coupled pair of asymmetric stepped impedance resonators, combined with other structures. The first and second dual‐wideband filters realize fractional bandwidths (FBW) of 43.2%/31.9% at the central frequencies (CF) of 1.875/1.63 GHz, and second bandwidths of 580 MHz/1.75 GHz at CF of 5.52/4.46 GHz, respectively. The proposed quad‐band filter realizes its first/second/third/fourth pass bands at CF 2.13/5.25/7.685/9.31 GHz with FBW of 46.0%/11.4%/4.6% and 5.4%, respectively. The wide pass bands are attributed to the mutual coupling of the modified ASIR resonators and their bandwidths are controllable by tuning relative parameters while the wide stop band performance is optimized by the novel interdigital cross coupled line structure and parallel uncoupled microstrip line structure. Moreover, the quad band is generated by introducing the novel defected rectangle structure. These multi‐standard filters are simulated, fabricated and measured, and measured results agree well with both simulated results and theory predictions. The good in‐band and out‐of‐band performances, the miniaturized sizes and simple structures of the proposed filters make them very promising for applications in future multi‐standard wireless communication.     

Dual‐band band pass filter using stub‐loaded open‐loop resonators with wide controllable bandwidths

Two dual‐band band pass filters (BPF) using stub‐loaded open‐loop (SLOL) resonator are presented in this article. A novel coupling tuning method by changing the relative coupling position of the resonators is proposed to control the bandwidth of each passband in a wide range. Transmission zeros are created to improve the selectivity by source‐load coupling. Because of the large ratio of two bandwidths, a novel dual‐band matching method is proposed to match the different load impedances at two passband frequencies to the same source impedance. Hence, relax the fabrication requirement of gap. The proposed dual‐band band pass filter is designed and fabricated. The measured 3 dB fractional bandwidths (FBWs) of two 2.45/5.25 GHz dual‐band BPFs are 6.5%/14.5% and 9.8%/5.5%, respectively. The results are in good agreement with the simulation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:367–374, 2014.     

Independently controllable dual‐band filter using single quad‐mode silver‐loaded dielectric resonator

This article proposes a novel bandpass filter with two controllable passbands using a single quad‐mode silver‐loaded dielectric resonator (DR). The silver plane is inserted in the middle of the cubic DR and two degenerate pairs are used to build the two passbands. Because of the distinct E‐field distributions, the silver plane has significant effect on the degenerate pair (TE^x₁₁₂ and TE^y₁₁₂), whereas another one (TE^x₁₁₁ and TE^y₁₁₁) remains unchanged. With the aid of the silver plane, both center frequencies and bandwidths of the two bands can be controlled independently. To verify the proposed idea, a prototype dual‐band BPF is designed and fabricated. Good agreement between simulated and measured results can be observed.     

Ultra‐compact dual mode dual band filter based on separate electric and magnetic coupling paths

A pair of dual mode independent controllable resonators used to realize dual band pass filter with good frequency selectivity and isolation is presented. The resonators are directly connected to input/output and are coupled through electric and magnetic coupling in two different paths. Magnetic coupling between the resonators is achieved using a common grounded via‐hole between the two set of quarter‐wavelength resonators. Electric coupling is achieved through open edge coupling of the resonators. Two independent resonators with Separate Electric and Magnetic Coupling (SEMC) paths produce an independently controllable dual band filter response and also additional transmission zeros (TZs) at the edges of the pass bands. The TZs are introduced to improve the selectivity of the filter. Filter exhibits desired pass band response at the Universal Mobile Telecommunications System (UMTS) band (1.95‐2.2 GHz) and Worldwide Interoperability for Microwave Access (WiMAX) band (3.4‐3.6 GHz). Proposed compact filter is implemented on RT/Duroid 5880 (ε_r = 2.2) substrate with thickness of 0.785 mm and surface area of 15 × 12 sq. mm.     

A bandpass filter using asymmetric stepped‐impedance resonators and symmetric T‐shape interdigital capacitor structures with wide out‐of‐band rejection

In this study, a novel stepped impedance resonator (SIR) is proposed. This SIR is composed of two stepped impedance transmission‐lines and an interdigital capacitor structure. The proposed resonator has a high ratio of the first spurious frequency f_s to the fundamental frequency f₀ and is suitable to design wide stopband filters. An equivalent model is used to analyze the resonant properties of the resonator. The design guidelines of the proposed resonator are summarized. Moreover, the coupling properties of the resonator are simulated and analyzed. Finally, a small high‐temperature superconducting bandpass filter is designed and fabricated using the proposed SIRs. The stopband of the filter is extended up to 4.0 f₀ and 3.5 f₀ with 30 and 60 dB out‐of‐band rejection levels, respectively.     

Design of high selectivity tri‐band bandpass filter with wide upper stopband

This article presents a dual‐plane structure high selectivity tri‐band bandpass filter (BPF) which consists of a pair of T‐shaped microstrip feed lines with capacitive source‐load coupling as well as spur lines embedded, and three resonators, i.e., a dual‐mode stub‐loaded stepped impedance resonator and two nested dual‐mode defected ground structure resonators. Using the intrinsic characteristics of the resonators and feed lines, nine transmission zeros near the passband edges and in the stopband can be generated to achieve high selectivity. An experimental tri‐band BPF located at 2.4/5.7 GHz [wireless local area networks (WLAN) application] and 3.5 GHz [worldwide interoperability for microwave access (WiMAX) application] has been simulated and fabricated. Good agreement between the simulated and measured results validates the design approach. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Dual‐band differential bandpass filter using stepped impedance resonators

In this article, a novel dual‐band differential bandpass filter using (SIRs) is designed. To demonstrate the design ideas, the differential and common mode equivalent half circuits are built and studied. Two resistors are connected between the two ends of the SIRs to consume the power in common mode. A capacitor is connected between the Ground and Center of the SIR to adjust the spurious frequencies, also strength the coupling of the two SIRs. The theoretical analysis shows the second band can be obtained by the proper impedance ratios of the resonances and the capacitor connected to the resonator. Two through ground vias (TGVs) connecting the top and bottom sides of the SIR filter, are used to realize the common mode rejection. To investigate the proposed filter in detail, a set of design equations are derived based on the circuit theory and transmission line theory. A phototype dual‐band differential filter operating at 1.5 and 2.75 GHz has been realized to validate the proposed concept and theory. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:468–473, 2015.     

Compact low‐cost microstrip lowpass filter with sharp roll‐off and wide attenuation band

A compact low‐cost lowpass filter (LPF) with sharp roll‐off and wide attenuation band using stepped impedance resonator loaded with interdigital fingers and U‐shaped resonator is recommended in this article. The proposed LPF has a cut‐off frequency of 1.2 GHz with a sharp roll‐off 135 dB/GHz and passband insertion loss 0.35 dB. An array of two different shapes of defected ground structures are etched in the ground plane for introducing additional transmission zeroes to enhance the stopband performance. The relative stopband suppression is achieved up to 171% with a suppression factor of 2. The proposed structure is modelled, fabricated, and measured. The measurement results are found to be well‐matched with the simulated ones. Eventually, a high figure of merit of 21 600 is achieved.     

Synthesis method of lumped dual–band filters with controllable bandwidths

This article presents a synthesis method for lumped dual‐band filters by directly adopting traditional Pi‐shaped and Г‐shaped capacitive networks as dual‐mode admittance inverters (J inverters). By following classic coupled‐resonator filter theory, the equivalent circuits (parallel LCs) of the dual‐mode resonators between the J inverters are derived separately at the two passbands. Each dual‐mode resonator is first approximately constructed with a series combination of the two parallel lumped circuit (LC) resonators, and then the element values are iteratively updated for better accuracy. A design example is given and good agreement is achieved between the simulated and measured results, demonstrating the feasibility of the synthesis method. The passband bandwidths are fully controllable. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:75–80, 2015.     

A compact dual‐band crossover using coplanar‐waveguide‐fed dual‐mode ring resonators

In this article, a compact dual‐band crossover using dual‐mode ring resonators by Coplanar‐Waveguide (CPW)‐Fed scheme is proposed. It contains 2 homocentric square ring resonators on the top layer to obtain the dual‐band responses. CPW feeding lines and open stubs are placed on the bottom layer to feed the ring resonators and adjust coupled strength. The center frequencies and bandwidths for each passband can be individually controlled easily. To prove the design concept, a compact dual‐band crossover operated at 1.57 and 2.45 GHz is designed and fabricated. The measured results show good agreement with the simulation ones results a wide frequency range.