Investigation on the Microstructure and Dielectric Properties of BaTiO3–Nb2O5–Fe2O3 Materials Doped with La2O3

The influence of La₂O₃ doped on the microstructure and dielectric properties, including the phase structure, temperature dependence of permittivity, and the hysteresis loop of BaTiO₃–Nb₂O₅–Fe₂O₃ (BTNF) materials has been investigated in X-ray diffraction, SEM, and LCR analyzer, respectively. Experiments revealed that incorporation of proper content of La₂O₃ basically soluted in the lattice of BaTiO₃ and can control the grain-growth, reduce the dielectric loss of the BTNF materials. The development of microstructure promoted by the additives can result in the improvement of the dielectric constant. When the doping concentration of La₂O₃ was 3.846 wt%, the relative dielectric constant of the sample sintered at 1280°C only for 2 h could reach 4308, and improve the dielectric-temperature characteristics markedly. As a result, a novel Y5P can be achieved in the BTNF ceramics, which is very promising for practical use in Y5P multilayer ceramic capacitors.     

Subsolidus Phase Relationships in the System Fe2O3–Al2O3–TiO2 between 1000° and 1300°C

Subsolidus phase equilibria in the system Fe₂O₃–Al₂O₃–TiO₂ were investigated between 1000° and 1300°C. Quenched samples were examined using powder X-ray diffraction and electron probe microanalytical methods. The main features of the phase relations were: (a) the presence of an M₃O₅ solid solution series between end members Fe₂TiO₅ and Al₂TiO₅, (b) a miscibility gap along the Fe₂O₃–Al₂O₃ binary, (c) an α-M₂O₃( ss ) ternary solid-solution region based on mutual solubility between Fe₂O₃, Al₂O₃, and TiO₂, and (d) an extensive three-phase region characterized by the assemblage M₃O₅+α-M₂O₃( ss ) + Cor( ss ). A comparison of results with previously established phase relations for the Fe₂O₃–Al₂O₃–TiO₂ system shows considerable discrepancy.     

In Situ Formation of Hexaferrite Magnets within a 3Y-TZP Matrix: La2O3–ZnO–Fe2O3 and BaO–Fe2O3 Systems

The in situ formation of magnetoplumbite-type (M-type) hexaferrites within a 3Y-TZP matrix was examined for the La₂O₃–ZnO–Fe₂O₃ and BaO–Fe₂O₃ systems. The formation of barium hexaferrite (Ba-M) was rapid enough at a temperature of 1300°C for 2 h to result in a uniform dispersion of fine Ba-M particles in a tetragonal zirconia polycrystal (TZP) matrix. However, the formation of lanthanum-substituted hexaferrite (La-M) was rather sluggish, despite the existence of a charge-compensating divalent oxide. The 3Y-TZP/20-wt%-BaFe₁₂O₁₉ in situ composite possessed good magnetic properties, as well as moderately good mechanical properties.     

Phase Relations in the System Iron Oxide—Cr2O3 in Air

The quenching method has been used to determine approximate phase relations in the system iron oxide-Cr₂O₃ in air. Only two crystalline phases, a sesquioxide solid solution (Fe₂O₃–Cr₂O₃) with corundum structure and a spinel solid solution (approximately FeO ·Fe₂O₃–FeO – Cr₂O₃), occur in this system at conditions of temperature and O₂ partial pressure (0.21 atm.) used in this investigation. Liquidus temperatures increase rapidly as Cr₂O₃ is added to iron oxide, from 1591°C. for the pure iron oxide end member to a maximum of approximately 2265°C. for Cr₂O₃. Spinel(ss) is the primary crystalline phase in iron oxide-rich mixtures and sesquioxide (ss) in Cr₂O₃–rich mixtures. These two crystalline phases are present together in equilibrium with a liquid and gas (po₂= 0.21 atm.) at approximately 2075°C.     

Phase Relations In The Pseudo-Ternary System La2O3–SrO–Fe2O3

The phase relations in the pseudo-ternary system La₂O₃–SrO–Fe₂O₃ have been investigated in air. Isothermal sections at 1100° and 1300°C are presented based on X-ray diffraction and thermal analysis of annealed samples. Extended solid solubility was observed for the compounds Sr _{n +1− v} La _v Fe _n O_{3 n +1−δ} ( n =1, 2, 3, and ∞) and Sr_{1− x} La _x Fe₁₂O₁₉, while only limited solubility of La in Sr_{4− z} La _z Fe₆O_13±δ was observed. At high Fe₂O₃ content, a liquid with low La₂O₃ content was stable at 1300°C.     

Two-Phase Coexistence in Single-Grain BaTiO3–(Mn0.5Zn0.5)Fe2O4 Composites, Via Solid-State Reaction

We have developed a synthesis method of single-grain two-phase BaTiO₃–(Mn_0.5Zn_0.5)Fe₂O₄ nanomaterials via a solid state reaction. The grains of BTO-rich samples were found to have a rod-like morphology with a high aspect ratio and a diameter of 200 nm, whereas the grains of MZF-rich samples had a tetrahedral/octahedral cross-section with a span of 200 nm. Such a synthesis of two-phase perovskite/spinel single-crystal grains with different grain geometries offers the potential to build new types of multiferroic materials.     

Phase Relationships in the Si3N4–SiO2–Lu2O3 System

Phase relationships in the Si₃N₄–SiO₂–Lu₂O₃ system were investigated at 1850°C in 1 MPa N₂. Only J-phase, Lu₄Si₂O₇N₂ (monoclinic, space group P 2₁/ c , a = 0.74235(8) nm, b = 1.02649(10) nm, c = 1.06595(12) nm, and β= 109.793(6)°) exists as a lutetium silicon oxynitride phase in the Si₃N₄–SiO₂–Lu₂O₃ system. The Si₃N₄/Lu₂O₃ ratio is 1, corresponding to the M-phase composition, resulted in a mixture of Lu–J-phase, β-Si₃N₄, and a new phase of Lu₃Si₅ON₉, having orthorhombic symmetry, space group Pbcm (No. 57), with a = 0.49361(5) nm, b = 1.60622(16) nm, and c = 1.05143(11) nm. The new phase is best represented in the new Si₃N₄–LuN–Lu₂O₃ system. The phase diagram suggests that Lu₄Si₂O₇N₂ is an excellent grain-boundary phase of silicon nitride ceramics for high-temperature applications.     

Formation of Core-Shell Structure in the BaTiO3-SrTiO3 System

When a 1-mol%-Fe₂O₃-added 0.67BaTiO₃-0.33SrTiO₃ (mole ratio) powder compact was sintered at 1380°C, a core-shell structure was developed. The core phase formed via solid-state interdiffusion of barium and strontium ions between BaTiO₃ and SrTiO₃ particles. In contrast, the shell phase formed via a solution-precipitation process in the presence of an Fe₂O₃-containing liquid phase. Energy-dispersive X-ray analysis showed that the core was a strontium-rich paraelectric phase and the shell was a barium-rich ferroelectric phase at room temperature. The core-shell structure developed in the BaTiO₃-SrTiO₃ system suggests the possibility of obtaining a variety of phase distributions with different Curie temperatures.     

Hydrothermal Soft Chemical Synthesis and Particle Morphology Control of BaTiO3 in Surfactant Solutions

Barium titanate (BaTiO₃) particles with book-like and spherical morphology were prepared by using a hydrothermal soft chemical process in the presence of a cationic surfactant. A layered titanate of H_1.07Ti_1.73O₄ with a lepidocrocite-like structure and plate-like particle morphology was used as the precursor. The layered titanate was hydrothermally treated in a Ba(OH)₂–(HTMA-OH) ( n -hexadecyltrimethylammonium hydroxide) solution or a Ba(OH)₂–(HTMA-Br) ( n -hexadecyltrimethylammonium bromide) solution in a temperature range of 80°–250°C to prepare BaTiO₃. The intercalation reaction of HTMA⁺ with the layered titanate promotes the structural transformation reaction from the layered titanates to BaTiO₃, while it inhibits the structural transformation reaction to anatase under the hydrothermal conditions. The particle morphology of BaTiO₃ prepared by this method dramatically changes with changing reaction conditions. HTMA⁺ plays an important role in changing particle morphology in the hydrothermal soft chemical process.     

Synthesis, Densification, and Phase Evolution Studies of Al2O3–Al2TiO5–TiO2 Nanocomposites and Measurement of Their Electrical Properties

Alumina–aluminum titanate–titania (Al₂O₃–Al₂TiO₅–TiO₂) nanocomposites were synthesized using alkoxide precursor solutions. Thermal analysis provided information on phase evolution from the as-synthesized gel with an increase in temperature. Calcination at 700°C led to the formation of an Al₂O₃–TiO₂ nanocomposite, while at a higher temperature (1300°C) an Al₂O₃–Al₂TiO₅–TiO₂ nanocomposite was formed. The nanocomposites were uniaxially compacted and sintered in a pressureless environment in air to study the densification behavior, grain growth, and phase evolution. The effects of nanosize particles on the crystal structure and densification of the nanocomposite have been discussed. The sintered nanocomposite structures were also characterized for dielectric properties.     

Subsolidus Phase Relations in the Ga2O3-In2O3-SnO2 System

Subsolidus phase relationships in the Ga₂O₃–In₂O₃–SnO₂ system were studied by X-ray diffraction over the temperature range 1250–1400°C. At 1250°C, several phases are stable in the ternary system, including Ga₂O₃( ss ), In₂O₃( ss ), SnO₂, Ga_{3− x} In_{5+ x} Sn₂O₁₆, and several intergrowth phases that can be expressed as Ga_{4−4 x} In_{4 x} Sn _{n −4}O_{2 n −2} where n is an integer. An In₂O₃–SnO₂ phase and Ga₄SnO₈ form at 1375°C but are not stable at 1250°C. GaInO₃ did not form over the temperature range 1000–1400°C.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Phase Equilibrium Relationships at Liquidus Temperatures in the System FeO–Fe2O3–Al2O3–SiO2

Phase equilibrium data at liquidus temperatures are presented for mixtures in the system FeO–Fe₂O₃–Al₂O₃–SiO₂. The volume located between the 1 and 0.2 atm. O₂ isobaric surfaces of the tetrahedron representing this system was studied in detail. Scattered data were obtained at lower O₂ pressures. Results obtained in the present investigation were combined with data in the literature to construct a phase equilibrium diagram, at liquidus temperatures, for the entire system FeO–Fe₂O₃–Al 2 O₃–SiO₂. Methods for interpretation of the diagram are explained.     

Weakly Coupled Relaxor Behavior of BaTiO3–BiScO3 Ceramics

The structural and dielectric properties of (1− x )BaTiO₃– x BiScO₃ ( x =0–0.5) ceramics were investigated to acquire a better understanding of the binary system, including determination of the symmetry of the phases, the associated dielectric properties, and the differences in the roles of Bi₂O₃ and BiScO₃ substitutions in a BaTiO₃ solid solution. The solubility limit for BiScO₃ into the BaTiO₃ perovskite structure was determined to be about x =0.4. A systematic structural change from the ferroelectric tetragonal phase to a pseudo-cubic one was observed at about x =0.05–0.075 at room temperature. Dielectric measurements revealed a gradual change from proper ferroelectric behavior in pure BaTiO₃ to highly diffusive and dispersive relaxor-like characteristics from 10 to 40 mol% BiScO₃. Several of the compositions showed high relative permittivities with low-temperature coefficients of capacitance over a wide range of temperature. Quantification of the relaxation behavior was obtained through the Vogel–Fulcher model, which yielded an activation energy of 0.2–0.3 eV. The attempt characteristic frequency was 10¹³ Hz and the freezing temperature, T _f, ranged from −177° to −93°C as a function of composition. The high coercive fields, low remanent polarization, and high activation energies suggest that in the BiScO₃–BaTiO₃ solid solutions, the polarization in nanopolar regions is weakly coupled from region to region, limiting the ability to obtain long-range dipole ordering in these relaxors under field-cooled conditions.     

Kinetics of Solid-State Reaction of Bi2O3 and Fe2O3

Solid-state reactions of equimolar mixtures of Bi₂O₃ and Fe₂O₃ from 625° to 830°C and their kinetics were investigated. The reaction rates were determined from the integrated X-ray diffraction intensities of the strongest peaks of the reactants and products. The activation energy for the formation of BiFeO₃ was 96.6±9.0 kcal/mol; that for a second-phase compound, Bi₂Fe₄O₉, which formed above 675°C, was 99.4±9.0 kcal/mol. Specific rate constants for these simultaneous reactions were obtained. The preparation of single-phase BiFeO₃ from the stoichiometric mixture of Bi₂O₃ and Fe₂O₃ is discussed.     

Novel Fabrication Route to Al2O3–TiN Nanocomposites Via Spark Plasma Sintering

A novel method for the preparation of Al₂O₃–TiN nanocomposites was developed. A mixture of TiO₂, AlN, and Ti powder was used as the starting material to synthesize the Al₂O₃–TiN nanocomposite under 60 MPa at 1400°C for 6 min using spark plasma sintering. X-ray diffractometry, scanning electron microscopy, and transmission electron microscopy were used for detailed microstructural analysis. Dense (up to 99%) nanostructured Al₂O₃–TiN composites were successfully fabricated, the average grain size being less than 400 nm. The fracture toughness ( K _{I C} ) and bending strength (σ_b) of the nanostructured Al₂O₃–TiN composites reached 4.22±0.20 MPa·m^1/2 and 746±28 MPa, respectively.     

Polymorphism and Dielectric Properties of Nb-Doped BaTiO3

A working subsolidus phase diagram for the system BaTiO₃–Ba₅Nb₄O₁₅ has been determined by firing sol–gel-synthesized samples over a range of temperatures. The main difference from previous diagrams is the greater extent of the Nb-doped BaTiO₃ cubic solid solutions, BaTi_{1−5 x} Nb_{4 x} O₃, at lower temperatures with x extending to 0.09 at 900°C, but only 0.05 at 1400°C. Electrical property measurements show that compositions with large x ( x ≥0.0025) are highly insulating for pellets sintered at 1300°C in air, followed by a slow cool. Compositions with low x , however, exhibit a residual semiconducting grain core and are not fully reoxidized readily. Composition dependence of the dielectric properties shows a continuous and smooth transition from classic ferroelectric behavior with pure BaTiO₃ to normal dielectric response with a temperature-independent relative permittivity of approximately 22–24 for x >∼0.08. At intermediate compositions, ranges of both relaxor ferroelectric and quasi-ferroelectric behavior are observed. Possible reasons for an observed anomalous increase in value of the permittivity at the ferroelectric transition temperature at low x , which is superposed on an overall decrease in permittivity with increasing x , are discussed.     

Phase Diagram of the Bi4Ti3O12–BaTiO3–(Na1/2Bi1/2)TiO3 System

The phases formed in the ternary system (Na_1/2Bi_1/2)TiO₃–Bi₄Ti₃O₁₂–BaTiO₃ (NBT–BTO–BT) were studied at 1150°C in air. A very accurate picture of the ternary phase diagram was obtained examining almost 90 different compositions, exploiting low-angle XRD analyses to study the layer compounds. New compounds with five perovskite blocks ( m =5) were discovered deep in the phase diagram. No compounds with m >5 were found. It was also established that pure perovskite compounds can be obtained only at compositions very close to the NBT–BT line. The relationships between the phases is discussed and it is hypothesized that the number of perovskite blocks in the system is determined by charged sites being created by the progressive substitution of Bi³⁺ in the A site of the perovskite blocks of BTO with the A cations of the perovskite end-member.     

SiO2/Fe2O3 Mesoporous Composite Prepared With an Activated Carbon Template in Supercritical Carbon Dioxide

SiO₂/Fe₂O₃ mesoporous composites have been prepared with a nanoscale casting process using an activated carbon (AC) template in supercritical carbon dioxide (SC CO₂). The composite precursor and acetone solvent (for Fe₂O₃ precursor) were dissolved in SC CO₂, and then coated on the AC in the desired supercritical condition. After removal of the AC template by calcinations in air at 600°C, SiO₂/Fe₂O₃ mesoporous composite were obtained. Temperature, pressure, and composite precursor ratio effects were studied. Scanning electron microscopy result shows that the porous structure of AC template had been well replicated by the composite product. Transmission electron micrograph indicates that nano iron oxides were well dispersed in the composite product.     

Phases in the Binary Systems PbO—La2O3, Gd2O3, and Sm2O3

In the binary system PbO–La_zO₃ only one compound, 4PbO.La₂O₃, exists; it is flanked by two eutectics. The structure of the compound, although of lower symmetry, is intimately related to the C modification of the rare earths. Below 800° to 1000°C, metastable solid solutions are formed from oxide mixtures coprecipitated from mixed solutions of the nitrates, the cubic parameter a = 5.66 A, if extrapolated to pure La₂O₃, corresponding to half the a parameter of the C form of La₂O₃. The solid solutions existing between the compositions La₂O₃–2Pb0 and pure La₂O₃ have a cubic face–centered lattice and obey Vegard's rule. The systems of PbO with Sm₂O₃ and Gd₂O₈ are quite similar to that with La₂O₃. The compound Sm₂O₃.4Pb0 decomposes at 1000°C with evaporation of PbO; Sm₂O₃ remains in the B modification.