Partial oxidation of methane over Ni/Ce-Zro<Subscript>2</Subscript>/θ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The catalytic behavior of Ni/Ce-ZrO₂/θ-Al₂O₃ has been investigated in the partial oxidation of methane (POM) toward synthesis gas. The catalyst showed high activity and selectivity due to the heat treatment of the support and the promotional effect of Ce-ZrO₂. It is suggested that the support was stabilized through the heat treatment of γ-Al₂O₃ and the precoating of Ce-ZrO₂, on which a protective layer was formed. Moreover, sintering of the catalyst was greatly suppressed for 24 h test. Pulse experiments of CH₄, O₂ and/or CH₄/O₂ with a molar ratio of 2 were systematically performed over fresh, partially reduced and well reduced catalyst. Results indicate that CH₄ can be partially oxidized to CO and H₂ by the reactive oxygen in complex NiO_x species existing over the fresh catalyst. It is demonstrated that POM over Ni/Ce-ZrO₂/θ-Al₂O₃ follows the pyrolysis mechanism, and both the carbonaceous materials from CH₄ decomposition over metallic nickel and the reactive oxygen species present on NiO_x and Ce-ZrO₂ are intermediates for POM.     

Pt–Ni/γ-Al2O3 catalyst for the preferential CO oxidation in the hydrogen stream

The preferential CO oxidation (PROX) in the presence of excess hydrogen was studied over Pt–Ni/γ-Al₂O₃. CO chemisorption, X-ray diffraction, transmission electron microscopy, energy dispersive X-ray spectroscopy and temperature-programmed reduction were conducted to characterize active catalysts. The co-impregnated Pt–Ni/γ-Al₂O₃ was superior to Pt/Ni/γ-Al₂O₃ and Ni/Pt/γ-Al₂O₃ prepared by a sequential impregnation of each component on alumina support. The PROX activity was affected by the reductive pretreatment condition. The pre-reduction was essential for the low-temperature PROX activity. As the reduction temperature increased above 423 K, the CO₂ selectivity decreased and the atomic percent of Ni in the bimetallic phase of Pt–Ni increased. This catalyst exhibited the high CO conversion even in the presence of 2% H₂O and 20% CO₂ over a wide reaction temperature. The bimetallic phase of Pt–Ni seems to give rise to high catalytic activity for the PROX in H₂-rich stream.     

Deactivation and coke formation on palladium and platinum catalysts in vegetable oil hydrogenation

Deactivation of palladium and platinum catalysts due to coke formation was studied during hydrogenation of methyl esters of sunflower oil. The supported metal catalysts were prepared by impregnating γ-alumina with either palladium or platinum salts, and by impregnating α-alumina with palladium salt. The catalysts were reused for several batch experiments. The Pd/γ-Al₂O₃ catalyst lost more than 50% of its initial activity after four batch experiments, while the other catalysts did not deactivate. Samples of used catalysts were cleaned from remaining oil by repeated extractions with methanol, and the amount of coke formed on the catalysts was studied by temperature-programmed oxidation. The deactivation of the catalyst is a function of both the metal and the support. The amount of coke increased on the Pd/γ-Al₂O₃ catalyst with repeated use, but the amount of coke remained approximately constant for the Pt/γ-Al₂O₃ catalyst. Virtually no coke was detected on the Pd/α-Al₂O₃ catalyst. The formation of coke on Pd/α-Al₂O₃ may be slower than on the Pd/γ-Al₂O₃ owing to the carrier’s smaller surface area and less acidic character. The absence of deactivation for the Pt/γ-Al₂O₃ catalyst may be explained by slower formation of coke precursors on platinum compared to palladium.     

Hydrodesulfurization of dibenzothiophene over supported and unsupported molybdenum carbide catalysts

A series of γ-Al₂O₃ supported molybdenum carbides [carbided Mo/γ-Al₂O₃ (MCS), Co-Mo/γ-Al₂O₃ (CMCS), and Ni-Mo/γ-Al₂O₃ (NMCS)] and unsupported molybdenum carbide (MCUS) were prepared by the temperature-programmed carburization of their corresponding molybdenum nitrides with 20 % CH₄/H₂. XRD and SEM studies show that unsupported molybdenum carbide catalyst possesses a typical crystalline Mo₂C (FCC structure), while supported molybdenum carbide catalysts possess highly dispersed surface molybdenum carbide species on an alumina oxide support. The results of dibenzothiophene (DBT) hydrodesulfurization over molybdenum carbide catalysts show that the reactivity is strongly dependent on the type of catalyst. Supported molybdenum carbide catalysts possess a higher reactivity than the unsupported molybdenum carbide catalyst. In addition, Co or Ni promoted, supported molybdenum carbide catalyst possesses a higher reactivity than the unpromoted, supported molybdenum carbide catalyst. The reactivity, which is also dependent on the reaction conditions, increases with increasing reaction temperature and pressure and contact time. The CO uptakes of the molybdenum carbide catalysts correlate well with overall activity (total rate) for DBT hydrodesulfurization. The major reaction product is biphenyl, with cyclohexylbenzene next in abundance regardless of the type of catalysts and reaction conditions. It was also found that the molybdenum carbide catalysts exhibit stable initial reactivity due to the stable and weak acidic characteristics of these catalysts.     

Synergism Between Ni and W in the Niw/ γ-Al2O3 Hydrotreating Catalysts

A series of NiW/ γ-Al₂O₃ catalysts (20 and 30 wt% W and 1–5 wt% Ni) have been prepared and studied by TPR and XPS. HDS activity has been tested in the thiophene conversion. The effect of Ni and W loadings on the formation of different structures is presented. In the calcined catalysts several phases coexist, concentrations of which depend on the Ni/(Ni+W) atomic ratio. The Ni synergistic effect in the HDS reaction is confirmed by the increase in the HDS activity (~10–15 times). This effect is ascribed to the formation of an active NiWS phase of high dispersion from the mixed NiW oxide precursors. At higher Ni/Ni+W ratio a redistribution of active components in additional amount ofNiWS phase during sulfidation is suggested.     

Characterization of nickel sulfate supported on γ-Al2O3 and its relationship to acidic properties

A series of NiSO₄/γ-Al₂O₃ catalysts were prepared by the impregnation method using an aqueous solution of nickel sulfate. The high catalytic activity of NiSO₄/γ-Al₂O₃ for both 2-propanol dehydration and cumene dealkylation was related to the increase of acidity and acid strength due to the addition of NiSO₄. 20(wt%)-NiSO₄/g-Al₂O₃ calcined at 600 °C exhibited maximum catalytic activities for 2-propanol dehydration and cumene dealkylation. The catalytic activities for both reactions were correlated with the acidity of catalysts measured by the ammonia chemisorption method. This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Modification of the alumina‐supported Mo‐based hydrodesulfurization catalysts by tungsten

The incorporation effect of tungsten as an activity‐promotional modifier into the Ni‐promoted Mo/γ‐Al₂O₃ catalyst was studied. Series of W‐incorporated catalysts with different content of tungsten were prepared by changing the impregnation order of nickel and tungsten onto a base Mo/γ‐Al₂O₃. Catalytic activities were measured from the atmospheric reactions of thiophene hydrodesulfurization (HDS) and ethylene hydrogenation (HYD). The HDS and HYD activities of the WMo/γ‐Al₂O₃ catalysts (WM series) initially increased and subsequently decreased with increasing content of tungsten as compared with those of their base Mo/γ‐Al₂O₃. The maximal activity promotion occurred at the W/(W + Mo) atomic ratio 0.025. For the Ni‐promoted Mo/γ‐Al₂O₃ catalysts, the effect of W incorporation was greatly dependent on the impregnation order of tungsten. The catalysts prepared by impregnating Ni onto the WMo/γ‐Al₂O₃ catalysts showed the same trend of activity promotion as for the WM series, while those by impregnating W onto a NiMo/γ‐Al₂O₃ catalyst resulted in lower activities than their base NiMo/γ‐Al₂O₃ catalyst. To characterize the catalysts, temperature‐programmed reduction and low‐temperature oxygen chemisorption were conducted. The effects of W incorporation on the NiMo‐based catalysts were discussed in reference to those on the CoMo‐based catalysts. This revised version was published online in July 2006 with corrections to the Cover Date.     

H2/CO2 separation characteristics of γ-Al2O3 membrane by aging stage in sol-gel process

γ-AlO(OH) sol solution was prepared by aluminum isopropoxide as an initial material. γ-Al₂O₃ membrane on the α-Al₂O₃ support was continuously made through coating and thermal treatment from the α-AlO(OH) sol. Previous work [Yoo et al., 1997] has shown that the aging stage in the sol preparation process mainly affects the characterization of γ-Al₂O₃ particles as well as γ-AlO(OH) sol. Based on this fact, the γ-Al₂O₃ membrane was prepared with two aging conditions in the present study. The separation characteristics experiment of the H₂/CO₂ mixture was performed on these membranes. As a result of the study, the mechanism of gas transport on the two membranes was proved as Knudsen diffusion. The ideal separation factor was reached at the value of the calculated Knudsen separation factor; however, permeability increased and selectivity decreased selectivity according to the aging.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Synthesis, characterization and hydrotreating performance of supported tungsten phosphide catalysts

Supported tungsten phosphide catalysts were prepared by temperature-programmed reduction of their precursors (supported phospho-tungstate catalysts) in H₂ and characterized by X-ray diffraction (XRD), BET, temperature-programmed desorption of ammonia (NH₃-TPD) and X-ray photoelectron spectroscopy (XPS). The reduction-phosphiding processes of the precursors were investigated by thermogravimetry and differential thermal analysis (TG-DTA) and the suitable phosphiding temperatures were defined. The hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) activities of the catalysts were tested by using thiophene, pyridine, dibenzothiophene, carbazole and diesel oil as the feedstock. The TiO₂, γ-Al₂O₃ supports and the Ni, Co promoters could remarkably increase and stabilize active W species on the catalyst surface. A suitable amount of Ni (3%–5%), Co (5%–7%) and V (1%–3%) could increase dispersivity of the W species and the BET surface area of the WP/γ-Al₂O₃ catalyst. The WP/γ-Al₂O₃ catalyst possesses much higher thiophene HDS and carbazole HDN activities and the WP/TiO₂ catalyst has much higher dibenzothiophene (DBT) HDS and pyridine HDN activities. The Ni, Co and V can obviously promote the HDS activity and inhibit the HDN activity of the WP/γ-Al₂O₃ catalyst. The G-Ni5 catalyst possesses a much higher diesel oil HDS activity than the sulphided industrial NiW/γ-Al₂O₃ catalyst. In general, a support or promoter in the WP/γ-Al₂O₃ catalyst which can increase the amount and dispersivity of the active W species can promote its HDS and HDN activities.     

Role of cobalt on γ-Al2O3 based NO x storage catalyst

Co/Pt/Ba/γ-Al₂O₃, Co/Ba/γ-Al₂O₃, Pt/Ba/γ-Al₂O₃, Co/Pt/γ-Al₂O₃, Ba/γ-Al₂O₃, Pt/γ-Al₂O₃, and Co/γ-Al₂O₃ type catalysts were prepared by a conventional impregnation method, and their NO _x storage capacities were evaluated by colorimetric assay. Co-containing catalysts had a higher NO _x storage capacity than that of Co-free counterparts. The role of each component, especially Co, for the catalysts prepared was investigated by using in-situ FTIR. The high NO _x storage for Co-containing catalysts including Co/Ba/γ-Al₂O₃ and Co/Pt/Ba/γ-Al₂O₃ is mainly due to the formation of Co₃O₄ on the catalyst surface identified by XAFS.     

Hydrodesulphurization performance of NiW/TiO2-Al2O3 catalyst for ultra clean diesel

TiO₂-Al₂O₃ binary oxide supports were obtained by sol–gel methods from Tetra-n-butyl-titanate and pseudoboehmite/aluminium chloride resources. The typical physico-chemical properties of NiW/TiO₂-Al₂O₃ catalysts with different TiO₂ loadings and their supports were characterized by means of BET, XRD and UV–vis DRS, etc. The BET results indicated that the specific surface areas of NiW/TiO₂-Al₂O₃ catalysts were as higher as that over pure γ-Al₂O₃ support, and the pore diameters were also large. The XRD and UV–vis DRS analyzing results showed that the Ti-containing supported catalysts existed as anatase TiO₂ species and the incorporation of TiO₂ could adjust the interaction between support and active metal, and impelled the higher reducibility of tungsten. The hydrodesulphurization (HDS) performance of the series catalysts were evaluated with diesel feedstock in a micro-reactor unit, and the HDS results showed that NiW/TiO₂-Al₂O₃ catalysts exhibited higher activities of ultra deep hydrodesulphurization of diesel oil than that of NiW/Al₂O₃ catalyst. The optimal TiO₂ content of NiW/TiO₂-Al₂O₃ catalysts was about 15 m%, and the corresponding HDS efficiency could reach to 100%. The sulphur contents of diesel products over NiW/TiO₂-Al₂O₃ (from pseudoboehmite/AlCl₃) catalysts with suitable TiO₂ content could be less than 15 ppmw, which met the sulphur regulation of Euro IV specification of ultra clean diesel fuel.     

Investigation of CH4 Reforming with CO2 on Meso-Porous Al2O3-Supported Ni Catalyst

Meso-porous Al₂O₃-supported Ni catalysts exhibited the highest activity, stability and excellent coke-resistance ability for CH₄ reforming with CO₂ among several oxide-supported Ni catalysts (meso-porous Al₂O₃ (Yas1-2, Yas3-8), -Al₂O₃, -Al₂O₃, SiO₂, MgO, La₂O₃, CeO₂ and ZrO₂). The properties of deposited carbons depended on the properties of the supports, and on the meso-porous Al₂O₃-supported Ni catalyst, only the intermediate carbon of the reforming reaction formed. XRD and H₂-TPR analysis found that mainly spinel NiAl₂O₄ formed in meso-porous Al₂O₃ and -Al₂O₃-supported catalysts, while only NiO was detected in -Al₂O₃, SiO₂, CeO₂, La₂O₃ and ZrO₂ supports. The strong interaction between Ni and meso-porous Al₂O₃ improved the dispersion of Ni, retarded its sintering and improved the activated adsorption of CO₂. The coking reaction via CH₄ temperature-programed decomposition indicated that meso-porous Al₂O₃-supported Ni catalysts were less active for carbon formation by CH₄ decomposition than Ni/-Al₂O₃ and Ni/-Al₂O₃.     

Promoting effect of propane traces on the activity of Pt/γ-Al2O3 and Pt–Sn/γ–Al2O3 catalysts in CH4–SO2–O2 reactions

A strong promoting effect of the presence of C₃H₈ or C₃H₆ was determined for the CH₄–SO₂–O₂ reaction, over pre-sulfated 1%Pt/γ–Al₂O₃ and pre-sulfated 1%Pt–2%Sn/γ–Al₂O₃ catalysts. These results suggest that over 1%Pt–2%Sn/γ–Al₂O₃ catalysts, small amounts of propane or propylene in the gas feed may eliminate methane emissions at low temperatures from lean-burn NGV exhausts.     

Explosive synthesis of ultrafine Al2O3 and effect of temperature of explosion

Synthesis of ultrafine Al₂O₃ is considered. An X-ray phase analysis indicates that ultrafine γ-Al₂O₃, (θ + α)-Al₂O₃, and α-Al₂O₃ are synthesized by explosion of water-gel explosives with a zero oxygen balance, prepared by mixing aluminum nitrate, RDX, and carbamide. All granules of ultrafine Al₂O₃ are spherical and homogeneous, and the granule size varies from 10 to 30 nm. The average crystal sizes of ultrafine Al₂O₃ are calculated by the Scherrer equation. The temperatures of explosion of water-gel explosives are found by a simplified approach. A comparison indicates that the higher the temperature of explosion, the greater the average nanocrystal size. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 5, pp. 127–131, September–October, 2006.     

Reduction of NO by CO on Cu/ZrO2/Al2O3 catalysts: Characterization and catalytic activities

ZrO₂, γ-Al₂O₃ and ZrO₂/γ-Al₂O₃-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H₂, Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO₂/γ-Al₂O₃ matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO₂. Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO₂.     

Influence of Ru segregation on the activity of Ru–Co/γ-Al2O3 during FT synthesis: A comparison with that of Ru–Co/SiO2 catalysts

γ-Al₂O₃ and SiO₂ supported Co catalysts, with varying amounts of Ru, were prepared and evaluated for Fischer–Tropsch synthesis (FTS). The composition of Ru for optimum activity was found to be support-dependent. The reducible Co₃O₄ was high in the region of 0–1.64 wt.% of Ru in Co/SiO₂ catalysts. Co/γ-Al₂O₃ displayed a maximum for reducible Co species at 0.42 wt.% Ru. Segregation of Ru occurred beyond this composition decreasing the extent of reduction. Co/γ-Al₂O₃ catalysts showed lower activity and olefin selectivity, in spite of higher Co dispersion, than Co/SiO₂ catalysts. The catalytic performance depends on the amount of reducible Co species, which again depends upon the optimum content of Ru.     

Effects of MgO promoter on properties of Ni/Al2O3 catalysts for partial oxidation of methane to syngas

The effects of MgO promoter on the physicochemical properties and catalytic performance of Ni/Al₂O₃ catalysts for the partial oxidation of methane to syngas were studied by means of BET, XRD, H₂-TPR, TEM and performance evaluation. It was found that the MgO promoter benefited from the uniformity of nickel species in the catalysts, inhibited the formation of NiAl₂O₄ spinel and improved the interaction between nickel species and support. These results were related to the formation of NiO-MgO solid solution and MgAl₂O₄ spinel. Moreover, for the catalysts with a proper amount of MgO promoter, the nickel dispersiveness was enhanced, therefore making their catalytic performance in methane partial oxidation improved. However, the excessive MgO promoter exerted a negative effect on the catalytic performance. Meanwhile, the basicity of MgO promoted the reversed water-gas shift reaction, which led to an increase in CO selectivity and a decrease in H₂ selectivity. The suitable content of MgO promoter in Ni/Al₂O₃ catalyst was ∼7 wt-%. Translated from Journal of Fuel Chemistry and Technology, 2006, 34(4): 450–455 [译自: 燃料化学学报]