Spatial variability of transport parameters in the Boom Clay

Several transport parameters (as hydraulic conductivity K, apparent diffusion coefficient D_p and diffusion accessible porosity η of HTO and iodide) have been intensively measured in the laboratory on high-quality cores taken at the Mol-1 borehole of the Mol site, in Belgium. The borehole was cored in 1997 from about 145 to 325 m depth, including the whole thickness of the Boom Formation, a Tertiary clay situated between 186 and 288 m depth (ground level), and part of the surrounding layers.The hydraulic conductivity measurements confirm the low permeability of the Boom Clay. An upper 90-m-thick clay layer within this formation can be considered as homogeneous with respect to the hydraulic conductivity. The vertical hydraulic conductivity K_v (i.e. K perpendicular to the bedding) is in the order of magnitude of 10⁻¹² m s⁻¹ and the average is 2.3×10⁻¹² m s⁻¹. This layer comprises from top to bottom the “Transition Zone”, the Putte Member, the Terhagen Member and the top of the Belsele-Waas Member of the Boom Formation. The 12 m at the base of the Formation, which corresponds to the lower part of the Belsele-Waas Member is characterised by larger K_v values (ranging between 10⁻¹¹ and 9×10⁻¹¹ m s⁻¹).The same thick clay layer can also be considered as homogeneous, regarding the values of the apparent diffusion coefficient and the diffusion accessible porosity η of tritiated water (HTO) and iodide. The average value of the diffusion accessible porosity is 0.37±0.03 for HTO and 0.16±0.02 for iodide. The apparent diffusion coefficient varies from 1.1×10⁻¹⁰ to 5.5×10⁻¹⁰ m² s⁻¹ for HTO and from 9.1×10⁻¹¹ to 5.2×10⁻¹⁰ m² s⁻¹ for iodide.     

Impedance investigation of the mechanism of copper electrodeposition from acidic perchlorate electrolyte

The mechanism of the copper electrodeposition from acidic perchlorate electrolyte has been investigated with polarization and impedance methods. The impedance of the copper electrode in copper perchlorate electrolytes has been measured as a function of frequency for different Edc overpotential values and different copper(II) ion concentrations. The relations between the shape of a complex plane impedance display and the copper electrode potential values as well as the concentration of CuII ion were analysed in terms of the electrode reaction mechanism. It is shown, that the presence of the intermediate cuprous ion and its sinusoidal change of transport rate is one of the main factors determining the depressed shape of the impedance arc. The quantitative relation between the faradaic impedance and the rates of electrode reaction rates was established. The impedance arc was simulated with a set of parameters involving: rate constants, Tafel slopes, diffusion coefficient of cuprous ion and double layer capacitance. The rate constants were calculated with respect to ECu2 + Cu00 as: k10 = 6.50 × 10−5 cm s−1, k20 = 0.139 cm s−1, k−20 = 1.88 × 10−7 mol cm−2 s−1.     

Amperometric detection of hydrogen peroxide at nano-nickel oxide/thionine and celestine blue nanocomposite-modified glassy carbon electrodes

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with nickel oxide (NiOx) nanoparticles and water-soluble dyes. By immersing the GC/NiOx modified electrode into thionine (TH) or celestine blue (CB) solutions for a short period of time (5–120 s), a thin film of the proposed molecules was immobilized onto the electrode surface. The modified electrodes showed stable and a well-defined redox couples at a wide pH range (2–12), with surface confined characteristics. In comparison to usual methods for the immobilization of dye molecules, such as electropolymerization or adsorption on the surface of preanodized electrodes, the electrochemical reversibility and stability of these modified electrodes have been improved. The surface coverage and heterogeneous electron transfer rate constants (k_s) of thionin and celestin blue immobilized on a NiOx-GC electrode were approximately 3.5 × 10⁻¹⁰ mol cm⁻², 6.12 s⁻¹, 5.9 × 10⁻¹⁰ mol cm⁻² and 6.58 s⁻¹, respectively. The results clearly show the high loading ability of the NiOx nanoparticles and great facilitation of the electron transfer between the immobilized TH, CB and NiOx nanoparticles. The modified electrodes show excellent electrocatalytic activity toward hydrogen peroxide reduction at a reduced overpotential. The catalytic rate constants for hydrogen peroxide reduction at GC/NiOx/CB and GC/NiOx/TH were 7.96 (±0.2) × 10³ M⁻¹ s⁻¹ and 5.5 (±0.2) × 10³ M⁻¹ s⁻¹, respectively. The detection limit, sensitivity and linear concentration range for hydrogen peroxide detection were 1.67 μM, 4.14 nA μM⁻¹ nA μM⁻¹ and 5 μM to 20 mM, and 0.36 μM, 7.62 nA μM⁻¹, and 1 μM to 10 mM for the GC/NiOx/TH and GC/NiOx/CB modified electrodes, respectively. Compared to other modified electrodes, these modified electrodes have many advantages, such as remarkable catalytic activity, good reproducibility, simple preparation procedures and long-term stabilities of signal responses during hydrogen peroxide reduction.     

Phase separation temperatures in the polystyrene—poly(α-methyl styrene)—methylcyclohexane system

The phase separation temperatures (PST) in the ternary system polystyrene (PS) (M_w = 1.75 × 10⁴ g mol⁻¹ — poly(α-methyl styrene) (PαMS) (M_w = 6.0 × 10⁴) — methylcyclohexane (MCH) and the binary systems PS-MCH and PαMS-MCH have been determined by using a He---Ne laser light-scattering apparatus over the total polymer weight fraction (W_{PS + PαMS}) range of 0.018 to 0.80 and various polymer blend ratios. The PST determined at a scattering angle of 0° agreed with those at 90° for the binary systems over polymer concentrations of 0.1 to 0.7 and for the ternary over W_{PS + PαMS} of higher than 0.3. Deviations of the PST determined at an angle of 90° from those at 0° were observed in the ternary system when W_{PS + PαMS} was lower than 0.3. Two phase separation temperatures, at which the intensity scattered from zero angle changed discontinuously, are observed at concentrations lower than W_{PS + PαMS} = 0.042 in the ternary system. The PST in the ternary system decreases monotonically with increasing W_{PS + PαMS} over 0.3 to 0.7. The phase diagram for the PS-PαMS-MCH system at W_{PS + PαMS} = 0.8 is characterized by a maximum PST around − 14°C.     

Bimetallic nickel complexes of trimethyl phenyl linked salicylaldimine ligands: Synthesis, structure and their ethylene polymerization behaviors

Bimetallic salicylaldimine-nickel complexes, 2,4,6-Me₃-1,3-{[NCH–(3′-R-5′-Y-2′-O–C₆H₃)-κ²-N,O]Ni(Ph) (PPh₃)}₂ [R = tert-Bu, Y = Me, 1b; R = Ph, Y = H, 2b] were prepared and their catalytic behaviors of ethylene polymerization were investigated. The bimetallic complex 2b shows higher activities (2.9 × 10⁵ g PE mol⁻¹ Ni h⁻¹) for ethylene polymerization and affords polymer with high molecular weight (M_w = 1.41 × 10⁵) and broad molecular weight distribution (M_w/M_n = 6.1) than its mononuclear matrix, {[(2,6-Me₂C₆H₃)–NCH–(3′-Ph-2′-O–C₆H₃)-κ²-N,O]Ni(Ph)(PPh₃)} (3) (Activity = 5.5 × 10⁴ g PE mol⁻¹ Ni h⁻¹; M_w = 1.86 × 10⁴; M_w/M_n = 2.8).     

Application of silica gel as an effective modifier for the voltammetric determination of dopamine in the presence of ascorbic acid and uric acid

Amorphous silica gel modified carbon paste electrode (CPE) offers substantial improvements in voltammetric sensitivity and selectivity towards determination of dopamine (DA). Cyclic voltammetry of Fe(CN)₆^3−/4− as a negatively charged probe revealed that the surface of the silica gel modified carbon paste electrode had a high density of negative charge at pH 8.0. Therefore, the modified electrode adsorbed DA (pK_a = 8.9) and enhanced its voltammetric response while repulsed ascorbic acid (AA) (pK_a = 4.2) and uric acid (UA) (pK_a = 5.4) and inhibited their interfering effects. The influence of various experimental parameters including percent of silica gel in the CPE, pH of solution, and accumulation time and potentials, on the voltammetric response of DA was investigated. At the optimum conditions, the analytical curve was linear for dopamine concentrations from 2.0 × 10⁻⁷ to 1.0 × 10⁻⁶ mol L⁻¹ and 2.0 × 10⁻⁶ to 1.5 × 10⁻⁴ mol L⁻¹ with a detection limit (3σ) of 4.8 × 10⁻⁸ mol L⁻¹. The prepared electrode was used for determination of DA spiked into DA injection and human serum samples, and very good recovery results were obtained over a wide concentration range of DA.     

Catalytic dissociation of hydrogen on a tantalum carbide filament in the HFCVD of diamond

New experimental results are presented which describe the behaviour of a carburised tantalum (TaC) filament in the HFCVD of a diamond film. An abrupt filament temperature drop is observed which is associated with the transition of the filament surface from poisoned to clean. By measuring the power increase needed to compensate for the temperature drop at a wide range of temperatures and corresponding CH₄ concentrations, and also considering the difference in radiative cooling of the filament, an energy balance is established. From this energy balance the production rate for H atoms by catalytic dissociation is obtained. It is found to increase from a level of about 3.8×10²⁰ cm⁻² s⁻¹ at 2200 °C to about 1.6×10²¹ cm⁻² s⁻¹ at 3000 °C. This increase, by a factor of 4.5, is somewhat lower than the increase in growth rate observed over the same temperature interval. The difference in these increase factors is interpreted as suggesting that thermal dissociation of H₂ plays a substantial role for H-atom production along with catalytic dissociation.     

Carbon nanotube-supported Pd–ZnO catalyst for hydrogenation of CO2 to methanol

A type of Pd–ZnO catalysts supported on multi-walled carbon nanotubes (MWCNTs) were developed, with excellent performance for CO₂ hydrogenation to methanol. Under reaction conditions of 3.0 MPa and 523 K, the observed turnover-frequency of CO₂ hydrogenation reached 1.15 × 10⁻² s⁻¹ over the 16%Pd_0.1Zn₁/CNTs(h-type). This value was 1.17 and 1.18 times that (0.98 × 10⁻² and 0.97 × 10⁻² s⁻¹) of the 35%Pd_0.1Zn₁/AC and 20%Pd_0.1Zn₁/γ-Al₂O₃ catalysts with the respective optimal Pd_0.1Zn₁-loading. Using the MWCNTs in place of AC or γ-Al₂O₃ as the catalyst support displayed little change in the apparent activation energy for the CO₂ hydrogenation, but led to an increase of surface concentration of the Pd⁰-species in the form of PdZn alloys, a kind of catalytically active Pd⁰-species closely associated with the methanol generation. On the other hand, the MWCNT-supported Pd–ZnO catalyst could reversibly adsorb a greater amount of hydrogen at temperatures ranging from room temperature to 623 K. This unique feature would help to generate a micro-environment with higher concentration of active H-adspecies at the surface of the functioning catalyst, thus increasing the rate of surface hydrogenation reactions. In comparison with the “Parallel-type (p-type)” MWCNTs, the “Herringbone-type (h-type)” MWCNTs possess more active surface (with more dangling bonds), and thus, higher capacity for adsorbing H₂, which make their promoting action more remarkable.     

Thermal stability of Mesoporous SBA-15 and Sn-SBA-15 Molecular Sieves: An in situ HTXRD study

Highly ordered SBA-15 and Sn-SBA-15 mesoporous molecular sieves with Si/Sn = 80, 60, 40 and 10 have been prepared through direct synthesis route under milder acidic conditions, which were used for the in situ high temperature X-ray diffraction (HTXRD) studies in the temperature range 298–1573 K for the first time in the literature. SBA-15 is found to be thermally stable up to 1473 K and appearance of α-cristobalite was observed at 1573 K also supported by the thermogravimetric (TG) data. A strong negative thermal expansion was observed on heating from 298 to 1573 K (α_a = −4.3 × 10⁻⁶ K⁻¹). Sn containing samples (Si/Sn = 80 and 60) showed a positive thermal expansion (6.75 × 10⁻⁶ K⁻¹ and 9.04 × 10⁻⁶ K⁻¹, respectively). On the other hand, the samples with Si/Sn = 40 and 10 showed a strong negative thermal expansion (−4.12 × 10⁻⁶ K⁻¹ and −7.56 × 10⁻⁶ K⁻¹) similar to SBA-15. The linear thermal expansion coefficient varied in the order: Si/Sn = 60 > 80 > 40 > 0 > 10. Sn⁴⁺ ions exhibit both tetrahedral and octahedral coordination depending upon the location of these ions either on the walls of the silica (Si/Sn = 80 and 60) or in the corona region of the structure (Si/Sn = 40 and 10), respectively. The thermal decomposition of the samples (TG data) is correlated to the thermal expansion behavior (HTXRD data). The decomposition behavior of template ions located within the pores is strongly influenced by the presence of Sn in the framework and a ‘soft’ interaction probably exists between the template ions and the Sn sites.     

The photoelectrochemical reduction of pyrene in acetonitrile solution

The reduction of pyrene (Py) at a mercury channel electrode is studied in acetonitrile solution, both in the dark and under conditions where the pyrene radical anion (Py^−.) is photoexcited, using a wavelength of 501.7 nm. In the dark a reversible one-electron process occurs forming the radical anion. However, upon photoexcitation of the electrogenerated radical anion, photocurrents are observed, and the precise electrode mechanism is shown to be: The photocurrent arising from further reduction of Py, since rapid homogeneous reactions of Py⁻² give electroinactive products. With this scheme an “effective” second order decay of Py^−√ is observed, RATE = −k_eff[Py^−√]^p2 where k_eff is proportional to k₃ I/k_f. k_eff has been evaluated from analysis of the limiting current-flow rate behaviour at the channel electrode at the channel electrode. This was found to be 4.0 ± 0.1 × 10³ mol−1 dm³ s⁻¹ at a light intensity of 0.30 W cm⁻² and a pyrene concentyration of 2.97 mM.     

Study of LiNi0.5Mn1.5O4 synthesized via a chloride-ammonia co-precipitation method: Electrochemical performance, diffusion coefficient and capacity loss mechanism

LiNi_0.5Mn_1.5O₄ powders are prepared via a new co-precipitation method. In this method, chloride salts are used as precursors and ammonia as a precipitator. The impurity of chlorine can be removed via a thermal decomposition of NH₄Cl in the subsequent calcination. X-ray diffraction pattern reveals that the final product is a pure spinel phase of LiNi_0.5Mn_1.5O₄. Scanning electron microscopy shows that the powders have an octahedron shape with a particle size of about 2 μm. Electrochemical test shows that the LiNi_0.5Mn_1.5O₄ powders exhibit an excellent cycling performance and after 300 cycles, the capacity retention is 83%. The lithium diffusion coefficient is measured to be 5.94 × 10⁻¹¹ cm² s⁻¹ at 4.1 V, 4.35 × 10⁻¹⁰ cm² s⁻¹ at 4.75 V and 7.0 × 10⁻¹⁰ cm² s⁻¹ at 4.86 V. The mechanism of capacity loss is also explored. After 300 cycles, the cell parameter ‘a’ decreases by 0.54% for the quenched sample (LiNi_0.5Mn_1.5O_4−δ) and by 0.42% for the annealed sample (LiNi_0.5Mn_1.5O₄). Besides, it is the first time to identify experimentally that the Ni and Mn ions dissolved in the electrolyte can be further deposited on the surface of anode.     

A novel 3D double helix cobalt(II) coordination polymer: Synthesis, crystal structures and third-order non-linear optical properties

One new metal-organic complex formulated as {[Co(bipy)₃][Co₂(μ₂–ox)₃]}_n 1 (bipy = 2,2′-bipyridyl; ox = oxalate) has been synthesized by low-temperature solid-state reaction and characterized by single-crystal X-ray diffraction, elemental analyses, IR spectra and UV–visible spectra. The complex 1 contains helical chains composed of left-handed and right-handed helices interlaced in pairs. The third-order non-linear optical (NLO) properties of the 1 were also investigated and they exhibit the reverse saturable absorption and self-defocusing performance with modulus of the hyperpolarizability (γ) 5.75 × 10⁻³⁰ esu for 1 in a 2.36 × 10⁻⁴ mol dm⁻³ DMF solution.     

Gasification of charcoal using supercritical CO2 at high pressures

A novel one-shell high temperature and high pressure semi-continuous reactor has been developed for the study of the Boudouard reaction at temperatures up to 820 °C and pressures up to 32.5 MPa. Semicontinuous gasification of charcoal using supercritical CO₂ has been achieved at conversions up to 90.8% (w/w) at LSHV between 20 and 30 h⁻¹ after 5–9 h. A gasification model is proposed and validated. Effective rates of gasification (1.32 ± 0.12) × 10⁻⁶ to (6.10 ± 2.03) × 10⁻⁵ s⁻¹ were obtained. The results indicated that this method is technically feasible for the on-line production of high pressures streams of CO/CO₂ in the lab for carrying out further chemistries, avoiding the use of CO high pressure bottles.     

Adsorption thermodynamics and kinetics study for the self-assembly of 1,8,15,22-tetraaminophthalocyanatocobalt(II) on glassy carbon surface

Spontaneous adsorption of 1,8,15,22-tetraaminophthalocyanatocobalt(II) (4α-Co^IITAPc) on glassy carbon (GC) electrode leads to the formation of a stable self-assembled monolayer (SAM). Since the SAM of 4α-Co^IITAPc is redox active, its adsorption on GC electrode was followed by cyclic voltammetry. SAM of 4α-Co^IITAPc on GC electrode shows two pairs of well-defined redox peaks corresponding to Co^III/Co^II and Co^IIIPc⁻¹/Co^IIIPc⁻². The surface coverage (Γ) value, calculated by integrating the charge under Co^II oxidation, was used to study the adsorption thermodynamics and kinetics of 4α-Co^IITAPc on GC surface. Cyclic voltammetric studies show that the adsorption of 4α-Co^IITAPc on GC electrode has reached the saturation coverage (Γ_s) within 3 h. The Γ_s value for the SAM of 4α-Co^IITAPc on GC electrode was found to be 2.37 × 10⁻¹⁰ mol cm⁻². Gibbs free energy (ΔG_ads) and adsorption rate constant (k_ad) for the adsorption of 4α-Co^IITAPc on GC surface were found to be −16.76 kJ mol⁻¹ and 7.1 M⁻¹ s⁻¹, respectively. The possible mechanism for the self-assembly of 4α-Co^IITAPc on GC surface is through the addition of nucleophilic amines to the olefinic bond on the GC surface in addition to a meager contribution from π stacking. The contribution of π stacking was confirmed from the adsorption of unsubstituted phthalocyanatocobalt(II) (CoPc) on GC electrode. Raman spectra for the SAM of 4α-Co^IITAPc on carbon surface shows strong stretching and breathing bands of Pc macrocycle, pyrrole ring and isoindole ring. Raman and CV studies suggest that 4α-Co^IITAPc is adopting nearly a flat orientation or little bit tilted orientation.     

Electrodeposition of silver from the system AgNO3—ethyleneglycol—water. Effect of temperature ( −30°C) on the smoothness of silver deposits

The electrodeposition of silver from a nitrate bath can be improved by lowering the temperature and by the addition of ethyleneglycol as anti-freeze. When the bath temperature is lowered below 0°C, the dendritic silver deposition is suppressed and a smooth surface is obtained; at −30°C a very finegrained deposit results. The dendritic growth is supposedly prohibited partly by the lowering of temperature and to a less extent by the adsorption of ethyleneglycol at the surface both of which might enhance the activation overvoltage of silver deposition. From the polarisation measurement in, 0·25 M AgNO₃ electrolytes, the exchange current density of Ag deposition was evaluated as 1·70 × 10⁻² A/cm²(25°C) and with 50 vol. per cent ethyleneglycol, 9·72 × 10⁻⁴ A/cm² (25°C) and 1·22 × 10⁻⁵ A/cm² (−32°C). Adsorption of ethyleneglycol on Ag cathode was discussed by differential capacitance change.     

Novel Hg and Mn supramolecular complexes with a versatile building block 5-(4-pyridyl)-1,3,4-oxadiazole-2-thiolate involving in situ ligand formation

Reaction of potassium N′-(pyridine-4-carbonyl)-hydrazinecarbodithioate ([K⁺(H₂L)⁻]) with Hg^II or Mn^II inorganic salt in the presence of 1,10-phenanthroline (phen) or 4,4′-bipyridine (bipy), yields complexes [Hg(pyt)₂(phen)] (1) and {[Mn(pyt)₂(H₂O)₂]·(bipy)·(H₂O)₂}_n (2), in which the pyt ligand (Hpyt = 5-(4-pyridyl)-1,3,4-oxadiazole-2-thiol) is obtained by in situ ligand formation from the acyclic precursor [K⁺(H₂L)⁻]. Single crystal X-ray diffraction suggests that the pyt anionic ligands in 1 and 2 behave as thiolate and thione isomers, respectively, and display S- and μ-N_pyridyl, N_oxadiazole-binding fashions. Complex 1 shows a 1-D fishbone-like supramolecular array via strong aromatic stacking interactions between the discrete mononuclear coordination motifs, whereas 2 has a 2-D layered host coordination framework with the inclusion of bipy and water guests in the cavities.     

Polymer-polymer interaction parameters in the ternary system polystyrene/poly(α-methyl styrene)/n-butyl chloride

The polymer-polymer interaction parameter χ′12, for the polystyrene/poly(α-methyl styrene)/n-butyl chloride ternary system, has been determined from activity coefficients of the solution measured using piezoelectric vapour sorption methods in the temperature range 30°–60°C. (These measurements where carried out in the concentration range 0.06 < ψ₀ < 0.26, where ψ is the segment fraction of the solvent). The values of χ¹⁰₁₂ extrapolated to zero solvent concentration over the range 30°–60°C, are large and negative (−0.2 to −0.9) χ¹₁₂ was found to increase with ψ₀. The negative values of χ¹₁₂ in this work are in agreement with the T_g in the polystyrene

Full-size image (1K)

M_w = 9.09 × 10⁴) blends on the point of blend compatibility. The polymer-polymer interaction parameters obtained in this work are discussed by taking into account the high susceptibility of polymers in the glassy state to solution of organic solvents.     

Novel coated graphite electrode for the selective determination of Gd(III) in rocks and waste water samples

A novel gadolinium selective coated graphite electrode based on 2,6-bis-[1-{N-cyanopropyl,N-(2-methylpridyl)}aminoethyl]pyridine [P] is described. The best performance was exhibited by the electrode having membrane composition P:NaTPB:PVC:NPOE as 8:4:30:58 (%, w/w). The electrode demonstrates excellent potentiometric characteristics towards gadolinium ion over several interfering ions. The electrode exhibited a Nernstian response to Gd³⁺ ion over a wide concentration range 2.8 × 10⁻⁷ to 5.0 × 10⁻² M with a detection limit (6.3 ± 0.1) × 10⁻⁸ M and slope 19.6 ± 0.1 mV decade⁻¹ of a_Gd³⁺. Furthermore, it showed a fast response time (12 s) and can be used for 2.5 months without significant divergence in its characteristics. Noticeably, the electrode can tolerate the concentration of different surfactants up to 1.0 × 10⁻⁴ M and can be used successfully in 30% (v/v) ethanol media and 10% (v/v) methanol and acetonitrile water mixture. The useful pH range of this sensor is 2.0 to 8.0. It is sufficiently selective and can be used for the determination of Gd³⁺ ions in waste water and rock samples. It also serves as a good indicator in the potentiometric titration of GdCl₃ with EDTA.     

PTFE-F-PbO2 电极在H2SO4溶液中的析氧行为

F-PbO2 electrode and polytetrafluoroethylene （PTFE） doped F-PbO2 electrode （PTFE-F-PbO2） were prepared on a plexiglas sheet substrate by a series of procedure including chemical and electrochemical depositions. The electrochemical activities of these two electrodes for oxygen evolution （OE） reaction were examined by electrochemical tests. In comparison with F-PbO2, PTFE-F-PbO2 electrode exhibited larger active surface area and higher oxygen vacancy deficiency, which resulted in its higher electrocatalytic activity for OE. In addition, both exchange current density and activation energy of the electrodes for OE were calculated in terms of active surface area. The values of exchange current density and activation energy in 0.5 mol·L^-1 H2SO4 aqueous solution were 1.125×10^ -3 mA·cm^-2 and 18.62 kJ·mol^-1 for PTFE-F-PbO2, and 8.384×10^-4 mA·cm^- 2 and 28.98 kJ·mol^-1 for F-PbO2, respectively. Because these values are calculated on the basis of the active surface areas of the electrodes, the enhanced activity of PTFE-F-PbO2 can be attributed to an increase in oxygen vacancy deficiency of PbO2 due to doping by PTFE. The influence of PTFE adulteration on the activity of PbO2 film electrode for OE was investigated in detail in this study.     

Amperometric glucose biosensor with high sensitivity based on self-assembled Prussian Blue modified electrode

A glucose biosensor, which was based on self-assembled Prussian Blue (PB) modified electrode with glucose oxidase (GOD) immobilized in cross-linked glutaraldehyde matrix, was developed. Fourier-transform infrared spectroscopy shows that the immobilized GOD retains its native conformation. Cyclic voltammetry was used to examine the electrocatalytic property of the enzyme electrode. The prepared glucose biosensor exhibits fast response (<4 s) and low detection limit of 5 × 10⁻⁶ M. The calculated apparent Michaelis constant K_M was 6.3 ± 1.2 mM, indicating a high affinity between the GOD and glucose. The effects of glutaraldehyde concentration and GOD loading on the sensitivity of the glucose biosensor have also been investigated. Under the optimal conditions, the biosensor shows a high sensitivity of about 80 mA M⁻¹ cm⁻² in a concentration range up to 1 × 10⁻³ M. The relative standard deviation (RSD) for intra-electrode and inter-electrode were 4% and 5%, respectively. In addition, the anti-interferent ability and stability of the biosensor were also discussed.