Effect of multi‐walled carbon nanotubes dispersity on the light transmittancy of multi‐walled carbon nanotubes/epoxy composites

Two types of multi‐walled carbon nanotubes (MWCNTs), chemically modified and unmodified, were dispersed in epoxy resin with ultrasonication. The light transmittance characteristics of epoxy composites with different ratios of MWCNTs to epoxy resin were measured at wavelengths ranging from 200 to 1100 nm. Results showed that composites with modified MWCNTs had a much higher light transmittance than those with unmodified MWCNTs. This was presumably due to a more uniform dispersion of modified MWCNTs in the epoxy matrix, as indicated by both transmission electron microscopy and optic microscopy. The wavelength dependency of light transmittance of the composites was expressed empirically as a function of weight fraction (f_w) of MWCNTs and the light wavelength (λ). POLYM. ENG. SCI. 46:635–642, 2006. © 2006 Society of Plastics Engineers.     

Preparation and properties of multi‐walled carbon nanotubes/carbon fiber/epoxy composites

Multi‐walled carbon nanotubes/carbon fiber (MWCNTs/CF) hybrid fillers are employed to prepare MWCNTs/CF/epoxy composites. Results reveal that a great improvement of the thermal conductivities of the epoxy composites with the addition of MWCNTs/CF hybrid fillers, and the thermal conductivity of the MWCNTs/CF/epoxy composites is 1.426 W/mK with 8 vol% treated MWCNTs/CF hybrid fillers (5 vol% MWCNTs + 3 vol% CF). Both the flexural and impact strength of the MWCNTs/CF/epoxy composites are increased firstly, but decreased with the excessive addition of MWCNTs. The flexural and impact strength of the MWCNTs/epoxy composites are optimal with 2 vol% MWCNTs. For a given MWCNTs/CF hybrid fillers loading, the surface treatment of MWCNTs/CF hybrid fillers can further increase the thermal conductivities and mechanical properties of the MWCNTs/CF/epoxy composites. POLYM. COMPOS., 35:2150–2153, 2014. © 2014 Society of Plastics Engineers     

Enhanced dielectric properties of polyamide 11/multi‐walled carbon nanotubes composites

Composites with multi‐walled carbon nanotubes (MWNTs) involved in polyamide 11 (PA11) were prepared via a conventional melt blending method. The structure, morphology, crystallization behavior, electrical, and dielectric properties of composites were investigated. The results demonstrated that the dispersed uniformly MWNTs favored the formation of α crystal of PA11 when the composites were quenched from melt. The dielectric constant of composites was dependent on the electric field frequency and MWNTs content, and the highest value of dielectric constant was as high as 350 for the composite with 1.21 vol % MWNTs at 10³ Hz, accompanied by a low dielectric loss. The enhanced dielectric properties could be interpreted by the formation of abundant nanocapacitors within the composites and the interfacial polarization effect resulting from accumulation of charge carriers at the internal interfaces between MWNTs and PA11. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42642.     

Mechanical and surface properties of polyurethane/fluorinated multi‐walled carbon nanotubes composites

To improve the mechanical and surface properties of poly(etherurethane) (PEU), multi‐walled carbon nanotubes (MWCNTs) were surface grafted by 3,3,4,4, 5,5,6,6,7,7,8,8,8‐tridecafluoro‐1‐octanol (TDFOL) (MWCNT‐TDFOL) and used as reinforcing agent for PEU. Fourier‐transform infrared spectroscopy revealed the successful grafting of MWCNTs. PEU filled with MWCNT‐TDFOL could be well dispersed in tetrahydrofuran solution, and tensile stress–strain results and dynamic mechanical analysis showed a remarkable increase in mechanical properties of PEU by adding a small amount of MWCNT‐TDFOL. Contact angle testing displayed a limited improvement (just 9°) in the hydrophobicity of PEU surface by solution blending with MWCNT‐TDFOL. However, a large improvement of surface hydrophobicity was observed by directly depositing MWCNT‐TDFOL powder on PEU surface, and the water contact angle was increased from 80° to 138°. Our work demonstrated a new way for the modification of carbon nanotubes and for the property improvement of PEU. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheological and thermal properties of epoxy nanocomposites reinforced with alkylated multi‐walled carbon nanotubes

The effects of functionalized multi‐walled carbon nanotubes (MWCNTs) on thermal and chemorheological behaviors of an epoxy‐based nanocomposite system were investigated. Chemical functionalization of MWCNTs by acid modification (A‐MWCNTs) and chemical amidation (D‐MWCNTs) was confirmed using Fourier transform infrared spectroscopy and thermogravimetric analysis. It was found that the D‐MWCNTs had a significant effect on the chemorheological behaviors of the epoxy‐based nanocomposite. Compared to the epoxy/A‐MWCNT nanocomposite, the epoxy/D‐MWCNTs nanocomposite showed a significant increase in gel time, as obtained from isothermal rheology measurements. Also, the storage modulus of the diglycidylether of bisphenol F (DGEBF)/D‐MWCNTs nanocomposite was higher than that of the DGEBF/D‐MWCNTs nanocomposite and gradually increased with an increase of frequency. This could be interpreted by the relatively strongly interconnected structure of the D‐MWCNTs in the DGEBF epoxy resin, which arises from the functionalized alkyl groups of the D‐MWCNTs in dispersion phases with the DGEBF epoxy resin. Copyright © 2012 Society of Chemical Industry     

Thermo‐mechanical and tribological properties of multi‐walled carbon nanotubes filled friction composite materials

Multi‐walled carbon nanotubes (MWCNTs) filled graphite lubricated phenolic‐based friction composites reinforced with combination of lapinus/Kevlar fibers have been fabricated and subsequently evaluated for their dynamic‐mechanical and tribological properties. The experimental results indicated that the higher MWCNT content enhances the thermal stability, whereas, lower MWCNT content enhances the thermo‐mechanical properties of the friction composites. The tribo‐performance evaluation has revealed that with the increase in MWCNT content, the friction‐fade and friction‐recovery performances are enhanced. The friction‐stability and friction‐variability coefficients are influenced by the combination of MWCNT, graphite, lapinus, and Kevlar constituents. The wear performance decreases with the increase in lapinus and MWCNT, whereas, it increases when the amount of Kevlar or graphite is increased in the composites. Wear surface morphological studies have led to the qualitative characterization of the topographical attributes and the nature of the frictional contact patches which is crucial in understanding the role of MWCNT on friction and wear mechanisms of the investigated automotive brake friction materials. POLYM. COMPOS., 38:1183–1193, 2017. © 2015 Society of Plastics Engineers     

Melt extrudate swell behavior of multi‐walled carbon nanotubes filled‐polypropylene composites

The extrudate swell behavior of polypropylene (PP) composite melts filled with multi‐walled carbon nanotubes (MWCNTs) was studied using a capillary rheometer in a temperature range from 190 to 230°C and at various apparent shear rates varying from 50 to 800 s⁻¹. It was found that the values of the extrudate swell ratio of the composites increased nonlinearly with increasing apparent shear rates, while the values of the extrudate swell ratio decreased almost linearly with increasing temperature. The values of the melt extrudate swell ratio increased approximately linearly with increasing shear stress, while decreased approximately nonlinearly with an increase of the MWCNT weight fraction. In addition, the extrudate swell mechanisms were discussed with observation of the fracture surface of the extrudate using a scanning electronic microscopy. This study provides a basis for further development of MWCNTs reinforced polymer composites with desirable mechanical and thermal properties. POLYM. COMPOS., 38:2433–2439, 2017. © 2015 Society of Plastics Engineers     

Effects of multi‐walled carbon nanotubes and conductive carbon black on electrical,dielectric, and mechanical properties of epoxidized natural rubber composites

The influence of multi‐walled carbon nanotubes (MWCNTs) and conductive carbon black (CCB) on cure, electrical, dielectric, and mechanical properties of epoxidized natural rubber (ENR) composites was investigated. It was found that short MWCNTs (S‐MWCNTs) with low loading significantly affected the cure characteristics in a way similar to high loading of CCB. Moreover, the ENR/S‐MWCNTs composites exhibited high AC conductivity, dielectric constant, and dielectric loss tangent (tan δ ) compared to the ENR/CCB and ENR/L‐MWCNTs (long MWCNTs) composites. In addition, the S‐MWCNTs composites showed the lowest percolation threshold concentration, defined as the lowest loading to form conductive paths in the insulating ENR matrix. This might be attributed to the comparatively high interfacial polarization, with good dispersion and distribution, of the S‐MWCNTs in ENR matrix. These characteristics were confirmed by TEM imaging and by a high bound rubber content, corroborating strong filler–rubber interactions in the ENR/S‐MWCNTs composites. However, the L‐MWCNTs composites showed the lowest electrical and other related properties, despite the highest aspect ratio and specific surface area of this filler. This might be because of the flocculation of nanotubes by mutual entanglement, leading to a poor uneven distribution in the ENR matrix. POLYM. COMPOS., 38:1031–1042, 2017. © 2015 Society of Plastics Engineers     

PMMA composites of single‐walled carbon nanotubes‐graft‐PMMA

To facilitate the dispersion of single‐walled carbon nanotubes (SWCNT) into poly(methyl methacrylate) (PMMA), SWCNT were functionalized with a RAFT chain transfer agent, and PMMA was grafted from the SWCNT by reversible addition–fragmentation transfer (RAFT) polymerization to give SWCNT‐g‐PMMA containing 6 wt % PMMA. SWCNT‐g‐PMMA in the form of small bundles was dispersed into PMMA matrices. The SWCNT‐g‐PMMA filler increased the glass transition temperature (T_g) of the composite when the matrix molecular weight M_n was less than the graft molecular weight, but not when the matrix M_n was equal to or greater than the graft M_n. The threshold of electrical conductivity of the composites as a function of weight percent SWCNT increased from 0.2% when matrix M_n was less than graft M_n to about 1% when matrix M_n was greater than graft M_n. Dynamic mechanical analyses of the composites having graft M_n less than or equal to matrix M_n showed broader rubbery plateaus with increased SWCNT content but no significant differences between samples with different grafted PMMAs. The results indicate that lower M_n matrix wets the SWCNT‐g‐PMMA whereas higher M_n matrix does not wet the SWCNT‐g‐PMMA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39884.     

Crystallization and melting behavior of multi‐walled carbon nanotube‐reinforced nylon‐6 composites

The crystallization and melting behavior of neat nylon‐6 (PA6) and multi‐walled carbon nanotubes (MWNTs)/PA6 composites prepared by simple melt‐compounding was comparatively studied. Differential scanning calorimetry (DSC) results show two crystallization exotherms (T_{CC, 1} and T_{CC, 2}) for PA6/MWNTs composites instead of a single exotherm (T_{CC, 1}) for the neat matrix. The formation of the higher‐temperature exotherm T_{CC, 2} is closely related to the addition of MWNTs. X‐ray diffraction (XRD) results indicate that only the α‐phase crystalline structure is formed upon incorporating MWNTs into PA6 matrix, independently of the cooling rate and annealing conditions. These observations are significantly different from those for PA6 matrix, where the increase in cooling rate or decrease in annealing temperature results in the crystal transformation from α‐phase to γ‐phase. The crystallization behavior of PA6/MWNTs composites is also significantly different from those reported in PA6/nanoclay systems, probably due to the difference in nanofiller geometry between one‐dimensional MWNTs and two‐dimensional nanoclay platelets. The nucleation sites provided by carbon nanotubes seem to be favorable to the formation of thermodynamically stable α‐phase crystals of PA6. The dominant α‐phase crystals in PA6/MWNTs composites may play an important role in the remarkable enhancement of mechanical properties. Copyright © 2005 Society of Chemical Industry     

Reinforcement of rigid PVC/wood‐flour composites with multi‐walled carbon nanotubes

Multi‐walled carbon nanotubes (CNT) were compounded with PVC by a melt blending process based on fusion behaviors of PVC. The effects of CNT content on the flexural and tensile properies of the PVC/CNT composites were evaluated in order to optimize the CNT content. The optimized CNT‐reinforced PVC was used as a matrix in the manufacture of wood‐plastic composites. Flexural, electrical, and thermal properties of the PVC/wood‐flour composites were evaluated as a function of matrix type (nonreinforced vs. CNT‐reinforced). The experimental results indicated that rigid PVC/wood‐flour composites with properties similar to those of solid wood can be made by using CNT‐reinforced PVC as a matrix. The CNT‐reinforced PVC did not influence the electrical and thermal conductivity of the PVC/wood‐flour composites. J. VINYL ADDIT. TECHNOL., 2008. © 2008 Society of Plastics Engineers.     

Electrically conductive polycarbonate/ethylene‐propylene copolymer/multi‐walled carbon nanotubes nanocomposites with improved mechanical properties

In this article, the effect of Multi‐walled carbon nanotubes (MWCNTs) on the electrical conductivity and mechanical properties of polycarbonate (PC) toughened with cross‐linked ethylene‐propylene copolymer (EPC) was investigated. The solubility parameters of the PC and EPC were calculated using Hoy methods to clarify the miscibility of the polymer blends. It could be concluded that in the cooled state, the blends form a heterogeneous structure with two separate phases. The tensile, flexural, impact toughness properties of the PC/EPC blend and PC/EPC/MWCNT nanocomposites were carried out to illuminate the optimum concentration of polymer blends and MWCNTs. The 335% increment for the impact strength results appeared with combination of 10% EPC in the PC matrix. The flexural modulus and strength of PC/EPC blend increased by 75.1% and 59.1%, respectively. The Nielsen model was performed to fit the best curve of theoretical simulation to experimental results for elastomeric dispersed in the plastic matrix. Halpin‐Tsai model was applied to estimate the stiffness of nanocomposites blends with different volume fraction and aspect ratio of MWCNTs in the PC/EPC blends. Finally, in the presence of MWCNTs, all nanocomposite samples were semi‐conducting and the percolation threshold of the PC/EPC (10%) blends was between 0.5% and 1.0% MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44661.     

Interfacial modification of single‐walled carbon nanotubes for high‐loading‐reinforced polypropylene composites

In this article, we present a strategy for fabricating polypropylene (PP)/polypropylene‐regrafted single‐walled carbon nanotube (PP‐re‐g‐SWNT) composites with a high loading of single‐walled carbon nanotubes (SWNTs; 20 wt %). The PP‐re‐g‐SWNTs were characterized by X‐ray photoelectron, Fourier transform infrared spectroscopy, transmission electron microscopy, and thermogravimetric analysis (TGA). The PP‐re‐g‐SWNTs showed excellent interfacial adhesion and dispersion. Furthermore, PP molecules, about 72 wt % by mass, were homogeneously bonded onto the surface of the SWNTs according to TGA. In this hybrid nanocomposite system, the PP‐re‐g‐SWNTs were covalently integrated into the PP matrix and became part of the conjugated network structure (as evidenced by differential scanning calorimetry and dynamic mechanical analysis) rather than just a separate component. Accordingly, the PP/PP‐re‐g‐SWNT composites presented obvious improvements in mechanical properties and conductivity (from 10^?10 to 10^?2). Most importantly, the tensile and flexural strength of the PP/PP‐re‐g‐SWNT composites did not exhibit an obvious downturn with the addition of 20 wt % SWNTs; this was contrary to documented results. We believe that these new observations were due to the novel structure of the PP‐re‐g‐SWNTs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39817.     

Isothermal crystallization kinetics of polypropylene in melt‐mixed composites of polypropylene and multi‐walled carbon nanotubes

The isothermal crystallization behaviour of the polypropylene (PP) phase in PP/multi‐walled carbon nanotubes (MWCNTs) composites has been investigated via differential scanning calorimetric analysis, which showed the influence of the varying dispersion level of MWCNTs in the respective PP matrix. PP/MWCNTs composites were prepared via melt‐blending technique, wherein two different grades of MWCNTs of varying average “agglomerate” size and varying entanglements (N‐MWCNTs and D‐MWCNTs) were utilized. Furthermore, the influence of melt‐viscosity of the PP phase was investigated on the crystallization kinetics of the PP/MWCNTs composites. Heterogeneous nucleation ability of MWCNTs has resulted in a decrease in half time of crystallization (t _1/2) from ～14 min for pure PP to ～6 min for PP/N‐MWCNTs and ～11 min for PP/D‐MWCNTs composites at 1 wt% of MWCNTs at 132 °C. Overall rate of crystallization (k) has significantly increased to 4.9 × 10^?2 min^?1 for PP/N‐MWCNTs composite as compared with 6.2 × 10^?3 min^?1 for PP/D‐MWCNTs composite at 0.5 wt% of MWCNTs at 132 °C. Moreover, the effect of a novel organic modifier, Li‐salt of 6‐amino hexanoic acid along with a compatibilizer (PP‐g‐MA) has also been investigated on the crystallization kinetics of the PP phase in PP/MWCNTs composites. POLYM. ENG. SCI., 57:1136–1146, 2017. © 2017 Society of Plastics Engineers     

Polymer nanocomposites reinforced with multi‐walled carbon nanotubes for semiconducting layers of high‐voltage power cables

Polymer nanocomposites reinforced with multi‐walled carbon nanotubes (MWCNTs) have been newly introduced for semiconducting layers of high‐voltage electrical power cables. Homogeneity of the MWCNT‐reinforced polymer nanocomposites was achieved by solution mixing, and their mechanical, thermal and electrical properties were investigated depending on the type of polymer. By changing the polymer matrix, the volume resistance of the MWCNT‐reinforced polymer nanocomposites could be varied by more than four orders of magnitude. Through systematic experiments and analysis, two possible factors affecting the volume resistance were found. One is the degree of crystallinity of the polymer used and the other is the change of MWCNT morphology under strain. By increasing the degree of crystallinity above a certain level, the volume resistance linearly increased. The MWCNTs embedded in the nanocomposites gradually protruded through the surface on stretching the sample and reversibly returned back to the original positions at a relatively small strain (below 20%). Based on the criteria of tensile properties and volume resistance, a poly[ethylene‐co‐(ethyl acrylate)]/MWCNT nanocomposite was selected as the best candidate for the semiconducting layers of high‐voltage electrical power cables. Copyright © 2009 Society of Chemical Industry     

Morphology,thermal, and electrical properties of polypropylene hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets

In this study, nanocomposites of polypropylene (PP) with various loadings of multi‐wall carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were formed by masterbatch dilution/mixing approach from individual masterbatches PP‐MWCNT and PP‐GnP. Melt mixing on a twin‐screw extruder at two different processing temperatures was followed by characterization of morphology by transmitted‐light microscopy including the statistical analysis of agglomeration behavior. The influence of processing temperature and weight fractions of both nanofillers on the dispersion quality is reported. Thermal properties of the nanocomposites investigated by DSC and TGA show sensitivity to the nanofillers weight fraction ratio and to processing conditions. Electrical conductivity is observed to increase up to an order of magnitude with the concentration of each nanofiller increasing from 0.5 wt % to 1.0 wt %. This is related with a decrease of electrical conductivity observed for unequal concentration of both nanofillers. This particular behavior shows the increase of electrical properties for higher MWCNT loadings and the increase of thermo‐mechanical properties for higher GnP loadings. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42793.     

Effects of multi‐walled carbon nanotube functionalization on the morphological and mechanical properties of nanocomposite foams based on poly(vinyl chloride)/(wood flour)/ (multi‐walled carbon nanotubes)

Experimental results are presented for nanocomposite foams based on unplasticized poly(vinyl chloride)/(wood flour)/(multi‐wall carbon nanotubes) (PVC/WF/MWCNTs). The nanocomposite samples were prepared in an internal mixer and foamed via a batch processing method using compression molding. Nanoparticles were functionalized by sodium hypochlorite solution, and the functionalization process was monitored by Fourier‐transform infrared spectroscopy. The effects of MWCNTs (both neat and functionalized) and blowing agent concentration on the morphological properties (cell size and cell density) and mechanical properties (tensile and flexural strength) of the foam samples were studied. The results revealed that foam cell sizes decreased and cell densities increased with addition of MWCNTs. The dispersion of nanoparticles in the PVC medium was increased by functionalization, and the morphological properties of the foams containing functionalized nanoparticles were improved. Density of nanocomposite foams decreased more with functionalized MWCNTs as compared to other samples. Chemical blowing agent concentration had no significant effect on sample density. Mechanical properties of the samples were improved by using functionalized MWCNTs in comparison with those of foams without this component. J. VINYL ADDIT. TECHNOL., 18:161–167, 2012. © 2012 Society of Plastics Engineers     

Electrically conductive multi‐walled carbon nanotube‐reinforced amorphous polyamide nanocomposites

Nanocomposites (NCs) based on an amorphous polyamide (aPA) and multi‐walled carbon nanotubes (MWCNTs) were obtained by melt‐mixing. As individual nanotubes were mostly observed, dispersion of the carbon nanotubes was deemed good. The electrical percolation threshold (p_c) occurred at 2.97 wt% MWCNTs and as a result, electrical conductivity improved by nine orders of magnitude upon addition of 6 wt% MWCNTs. The 6 wt% MWCNTs also led to an increase in both thermal stability (measured by the degradation temperature) and Young's modulus (19%) for the NCs, and ductility remained the same. POLYM. COMPOS., 35:587–595, 2014. © 2013 Society of Plastics Engineers     

Rheological properties and fracture toughness of epoxy resin/multi‐walled carbon nanotube composites

Multi‐walled carbon nanotubes (MWCNTs), surface‐treated via chemical functionalization, i.e., oxidation and amidation, were used to reinforce diglycidylether of bisphenol F (DGEBF) epoxy resin. The effects of the functionalization on the dispersion stability, rheological properties, and fracture toughness of DGEBF/MWCNT composites were investigated. The dispersion homogeneity of the MWCNTs in the epoxy matrix improved after functionalization. In addition, isothermal rheology measurements revealed that the DGEBF/dodecyl amine‐functionalized MWCNT (D‐MWCNT) composite had a longer gel time and higher activation energy of cross‐linking than the DGEBF/acid‐treated MWCNT (A‐MWCNT) composite. The fracture toughness of the former was also significantly higher than that of the latter; this resulted from the relatively high dispersion stability of the D‐MWCNTs in the epoxy matrix, owing to the presence of alkyl groups on the D‐MWCNT surface. POLYM. ENG. SCI., 55:2676–2682, 2015. © 2015 Society of Plastics Engineers     

Linear viscoelastic properties and crystallization behavior of multi‐walled carbon nanotube/polypropylene composites

Multi‐walled carbon nanotube/polypropylene composites (PPCNs) were prepared by melt compounding. The linear viscoelastic properties, nonisothermal crystallization behavior, and kinetics of PPCNs were, respectively, investigated by the parallel plate rheometer, differential scanning calorimeter (DSC), X‐ray diffractometer (XRD), and polarized optical microscope (POM). PPCNs show the typical nonterminal viscoelastic response because of the percolation of nanotubes. The rheological percolation threshold of about 2 wt % is determined using Cole‐Cole method. Small addition of nanotube can highly promote crystallization of PP matrix because of the heterogeneous nucleating effect. With increasing nanotube loadings, however, the crystallization rate decreases gradually because the mobility of PP chain is restrained by the presence of nanotube, especially at high loading levels. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008