Copolymerization of poly(1‐naphthylamine) with aniline and o‐toluidine

The commercial use of polyaniline has been impeded by its intractable nature and insolubility. The use of substituted polyaniline has been attempted mainly to increase the processibility of polyaniline, but this approach usually results in the lowering of the conductivity. This study reports the synthesis of poly(1‐naphthylamine), a fused ring derivative of polyaniline, and its copolymers with aniline and o‐toluidine via a chemical polymerization method. Spectral, thermal, morphological, and conductivity studies were carried out to elucidate the influence of the incorporation of aniline and o‐toluidine units into poly(1‐naphthylamine). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of poly(β‐pinene)‐g‐polystyrene from allylic brominated poly(β‐pinene)

Poly(β‐pinene) was brominated by N‐bromosuccinimide on the allylic carbons. Then the brominated product was activated by AlEt₂Cl to initiate the polymerization of styrene to give a β‐pinene/styrene graft copolymer. AlEt₂Cl was selected because it alone could not initiate the polymerization of styrene. The obtained graft copolymer was characterized by GPC, ¹H‐NMR, and DSC measurements, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 599–603, 2000     

Synthesis and characterizations of poly(4‐alkylthiazole vinylene)

Two poly(thiazole vinylene) derivatives, poly(4‐hexylthiazole vinylene) (P4HTzV) and poly(4‐nonylthiazole vinylene) (P4NTzV), were synthesized by Pd‐catalyzed Stille coupling method. The polymers are soluble in common organic solvents such as o‐dichlorobenzene and chloroform, and possess good thermal stability. P4HTzV and P4NTzV films exhibit broad absorption bands at 400–720 nm with an optical bandgap of 1.77 eV and 1.74 eV, respectively. The HOMO (the highest occupied molecular orbital) energy levels of P4HTzV and P4NTzV are ?5.11 and ?5.12 eV, respectively, measured by cyclic voltammetry. Preliminary results of the polymer solar cells based on P4HTzV : PC₆₁BM ([6,6]‐phenyl‐C‐61‐butyric acid methyl ester) (1 : 1, w/w) show a power conversion efficiency of 0.21% with an open‐circuit voltage of 0.55 V and a short circuit current density of 1.11 mA cm^?2, under the illumination of AM1.5G, 100 mW cm^?2. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of polyrotaxanes comprising α‐cyclodextrins and poly(ε‐caprolactone) end‐capped with poly(butyl methacrylate)s

Biodegradable polyrotaxane‐based triblock copolymers were synthesized via the bulk atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) initiated with polypseudo‐rotaxanes (PPRs) built from a distal 2‐bromoisobutyryl end‐capped poly(ε‐caprolactone) (Br‐PCL‐Br) with α‐cyclodextrins (α‐CDs) in the presence of Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 45 ºC. The structure was characterized in detail by means of ¹H NMR, gel permeation chromatography, wide‐angle X‐ray diffraction, DSC and TGA. When the feed molar ratio of BMA to Br‐PCL‐Br was changed from 128 to 300, the degree of polymerization of PBMA blocks attached to two ends of the PPRs was in the range 382 ? 803. Although about a tenth of the added α‐CDs were still threaded onto the PCL chain after the ATRP process, the movable α‐CDs made a marked contribution to the mechanical strength enhancement, blood anticoagulation activity and protein adsorption repellency of the resulting copolymers. Meanwhile, they could also protect the copolymers from the attack of H₂O and Lipase AK Amano molecules, exhibiting a lower mass loss as evidenced in hydrolytic and enzymatic degradation experiments. © 2013 Society of Chemical Industry     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Development of novel conducting composites of nanostructured poly(1‐naphthylamine) with poly(vinyl chloride)

Investigations on the synthesis of nanoconducting polymers have gained much popularity during the past few decades. The processibility of the nanostructured conducting polymers is poor, which hinders their commercial application. Considering the drawbacks of nanostructured conducting polymers, this article reports for the first time the synthesis of processible composites of nanostructured poly(1‐naphthylamine) (PNA), a polyaniline derivative with poly(vinyl chloride) (PVC). The composites were prepared by loading different weight ratios of PNA (2–10 wt%) in PVC. The composites were characterized by spectral, thermal, morphological, and conductivity studies. The particle size of PNA/PVC composites was confirmed by transmission electron microscopy and was found to be in the range of 5–20 nm. The highest conductivity of 2.5 × 10⁻² S/cm was obtained in the composite with 4 wt% loading of PNA. The high conductivity of the composites was correlated to the agglomerate‐free uniform dispersion of self‐assembled nanofibrillar network of PNA particles in the PVC matrix. The PNA/PVC composites exhibited good mechanical properties, which holds potential for use in semiconductor nanodevices. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Synthesis and degradation of poly (alkyl α-cyanoacrylates)

In order to study structure-tissue reactivity relationships and ultimately develop a less necrotizing adhesive, this laboratory undertook a study of the synthesis and degradation of the homologous series of α-cyanoacrylate monomers and polymers. A method for synthesizing high purity cyanoacrylates and some of their chemical and physical properties and presented. In vitro kinetics studies under heterotgeneous and homogeneous conditions indicate that cyanoacrylate polymers degrade by hydrolytic scission of the polymer chain. The products resulting from such a scission are formaldehyde (positively identified by derivative formation) and ultimately and alkyl cyanoacetate. As the homologous series is ascended, the rate of degradation under neutral conditions decreases. In homogeneous solutions, under alkaline conditions, the ràte of degradation is considerably higher than under neutral conditions and the rates obtained with the methyl to the butyl derivative are of the same order. Aproposed mechanism of degradation is presented. Medical evaluation has indicated that as the homologous series is ascended, the greater the tissue tolerance to the monomers and polymers. The relevance of the results of the in vitro studies to this medical finding is presented.     

Interpenetrating polymer networks of poly(butyl methacrylate) and poly(α‐terpineol‐co‐styrene): Synthesis and characterization

Simultaneous interpenetrating polymer networks (IPNs) based on poly(butyl methacrylate) and poly(α‐terpineol‐co‐styrene) were synthesized with azobisisobutyronitrile (AIBN) as the initiator and divinyl benzene as the crosslinking agent in xylene under an inert nitrogen atmosphere. Fourier transform infrared spectra provided structural evidence for the IPNs, indicating characteristic frequencies of ester groups of butyl methacrylate at 1723 cm^?1 and alcoholic groups of α‐terpineol at 3436 cm^?1. Scanning electron microscopy revealed threadlike network structures. Properties such as percentage swelling and average molecular weight between crosslinks were direct functions of the copolymer and initiator (AIBN) concentrations and inverse functions of the monomer (butyl methacrylate) and crosslinking agent (divinyl benzene) concentrations. Differential scanning calorimetry showed an IPN glass‐transition temperature at 80.2°C. The thermal decompositions of the IPNs were established with the help of thermogravimetric analysis. The value of the activation energy, calculated from thermogravimetric analysis with the Coats and Redfern equation, was 23 kJ/mol. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 343–352, 2006     

Synthesis of acrylamide end‐functionalised poly(1‐hexene) using an α‐diimine nickel catalyst

The nickel precursor [bis(N,N′‐dimesitylimino)acenaphthene]dibromonickel and methylaluminoxane were used to catalyse the functionalisation of 1‐hexene with acrylamide by passivation of acrylamide with tri‐isobutylaluminium. The polymer obtained was characterised by GPC/SEC and NMR. The NMR experiments performed, COSY, DEPT, long‐range selective INEPT, HSQC and TOCSY 1D, showed that a 2,1 insertion of a single molecule of acrylamide per macromolecule had occurred at the end of the polyhexene chain. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

β‐cyclodextrin/poly(vinyl alcohol) hydrogels containing phenylpropionic acid and naphthylamine: dual pH‐sensitive release

Hydrogel composed of β‐cyclodextrin (β‐CD) and poly(vinyl alcohol) was prepared in a strong alkaline condition using epichlorohydrin as a crosslinker. Phenylpropionic acid (PPA) and naphthylamine (NA) were loaded in the cavities of β‐CD residues to endow the hydrogel with a dual pH‐sensitive characteristic. In release experiments using fluorescein isothiocyanate‐dextran (FITC‐dextran) as a dye, PPA/NA‐loaded hydrogel exhibited an extensive release not only in acidic conditions (e.g. pH 3.0) but also in alkaline conditions (e.g. pH 9.0). PPA and NA will be highly ionized at the alkaline and the acidic pH and they could promote swelling of the hydrogel, causing an extensive release at those pH values. However, the release was suppressed at mid pH values (e.g. pH 5.0 and pH 7.4), possibly due to the formation of salt bridges between PPA^? and NA⁺. In fact, the degree of swelling at mid pH was lower than that observed at strong acidic pH and alkaline pH. According to SEM images, the pore size and the texture compactness of hydrogels which had been subjected to swelling at different pH values could also account for the dual pH‐sensitive releases. The hydrogels exhibited dual pH sensitivities in terms of FITC‐dextran release and swelling. These hydrogels might be used as a pH‐sensitive vehicle for water‐soluble drugs. © 2013 Society of Chemical Industry     

Synthesis and characterization of poly(allyl methacrylate) obtained by γ‐radiation

Allyl methacrylate was polymerized by γ‐radiation under vacuum in solution and atom transfer radical polymerization (ATRP) methods and also in the presence of atmospheric oxygen in bulk. The kinetic curve is S‐type with a longer induction period, because of the presence of oxygen, in bulk polymerization. The curve for the solution polymerization is almost linear with a short induction period. The rate started to decrease after about 60% conversion and reached to a limiting conversion of 100%. The polymerization by ARTP method using γ‐radiation as initiator instead of conventional heating method gave a kinetic curve of linear character up to about limiting conversion of 100%. The polymers obtained were mostly gel type with linear chain fractions at lower conversions. The polymer characterizations were carried out by FTIR, differential scanning calorimetry, NMR, TGA, and XRD methods. The polymers were shown to proceed by the opening of vinyl groups. The allyl groups caused a limiting crosslinking, but 98–99% of the allyl groups are shown by FTIR and NMR, unchanged during the polymerization. The cyclic type polymer formation was not likely taking place. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1076–1083, 2007     

Synthesis and characterization of α‐amino acid‐containing polyester: poly[(ε‐caprolactone)‐co‐(serine lactone)]

Novel polyesters, poly[(ε‐caprolactone)‐co‐(N‐trityl‐L ‐serine‐β‐lactone)]s, were prepared by copolymerizing ε‐caprolactone (CL) with N‐trityl‐L ‐serine‐β‐lactone (TSL) using ZnEt₂ as the catalyst. The number‐average molecular weights were determined which ranged from 2.7 × 10⁴ to 4.9 × 10⁴ Da with dispersity values ranging from 1.6 to 1.8. The structures of the copolymers were investigated by means of ¹H NMR, ¹³C NMR and infrared spectroscopies, thermogravimetric analysis and differential scanning calorimetry. The results indicated that CL and TSL monomer units were randomly distributed within the copolymer backbone structures and the ratios of TSL to CL in the copolymers were close to those in the feeds. After removal of the trityl group under mild condition, a new polyester with side amino groups provided by serine units was obtained. L929 cell culturing test indicated good biocompatibility of the polyester with or without protective groups. © 2012 Society of Chemical Industry     

Synthesis and characterization of amphiphilic hydroxypropylcellulose‐graft‐poly(ε‐caprolactone)

An amphiphilic graft copolymer, hydroxypropylcellulose‐graft‐poly(ε‐caprolactone) (HPC‐g‐PCL), was synthesized by bulk polymerization without a catalyst and characterized with one‐dimensional and two‐dimensional NMR spectroscopy. Molar substitution of ε‐caprolactone on HPC (MS_CL) was estimated by both gravimetry and ¹H‐NMR, and the gravimetric method was considered suitable for MS_CL determination. Heterogeneity in the HPC‐g‐PCL film was suggested by a microscopic study, and the existence of PCL‐rich crystalline regions was confirmed by the results of X‐ray diffraction and differential scanning calorimetry (DSC). The double endotherm observed in the DSC scans of HPC‐g‐PCL was associated with the different molecular weight fractions in the copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 718–727, 2003     

Blends of poly(3‐hydroxybutyrate) with poly(β‐alanine) and its derivatives

Nanofibers and films of poly(3‐hydroxybutyrate) (PHB)/nylon 3 [poly(β‐alanine) (N3)], PHB/poly(α‐methyl‐β‐alanine) (2mN3), and PHB/poly(β‐methyl‐β‐alanine) (3mN3) blends were prepared by electrospinning and film‐casting techniques, respectively. The miscibility of the blends was studied by Fourier transform infrared spectrometry, differential scanning calorimetry, thermogravimetric analysis, and X‐ray diffraction (XRD). The electrospinnability of the blends was studied by scanning electron microscopy. Some characteristic IR absorption bands of the components in the blends shifted gradually with changes in the compositions. The melting temperature and decomposition temperature of PHB decreased gradually with increasing fractions of N3, 2mN3, and 3mN3. The XRD spectra of all of the blends exhibited peaks with lower intensities compared to those of the neat species. The suppression of PHB crystallinity in the blends after blending was attributed to the disruption of its crystal lattice and the prevention of recrystallization of each component by means of other components and segmental interactions between the components in the amorphous phase. Thermal, spectroscopic, and optical analyses of the polymer blends revealed that the polymers were miscible with good compatibility, and this could have improved the scaffold properties of PHB. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40484.     

Synthesis and investigation of the properties of poly(phenyl‐α‐naphthylsilylene)–dimethylsilylene copolymers

A Wurtz‐type reductive coupling reaction of dichlorophenyl‐α‐naphthylsilane was carried out in a mixture of toluene and o‐xylene in the presence of sodium and a catalytic amount of mercury; α,ω‐dichlorophenyl‐α‐naphthylsilylenes of various degrees of polymerization were obtained. Through the hydrolysis of α,ω‐dichlorophenyl‐α‐naphthylsilylenes, corresponding dihydroxy compounds were obtained. The heterofunctional polycondensation of α,ω‐dihydroxyphenyl‐α‐naphthylsilylenes with α,ω‐dichlorodimethylsilylenes was performed both without amines and in the presence of amines. Heterofunctional polycondensation without amines did not proceed with the formation of high molecular weight compounds because the cleavage of both ? Si? Si? and ?Si? O? Si? bonds took place during condensation. In the presence of amines, polysilylene–silylene copolymers were obtained. The synthesized copolymers were investigated with gel permeation chromatography, differential scanning calorimetry, roentgenography, and thermogravimetry. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1047–1056, 2002     

Interface formation of Ca with poly(p-phenylene α,α′-diphenyl vinylene) and poly(p-phenylene α-phenyl vinylene)

We have investigated the interface formation of Ca with poly(p-phenylene α,α′-diphenyl vinylene) (PPV-DP) and poly(p-phenylene α-phenyl vinylene) (PPV-P) using X-ray photoemission spectroscopy (XPS). Similarly to our earlier findings in metal/PPV interface formation, the O 1s peak shifted toward a lower binding energy as soon as Ca was deposited on to the polymers. This was accompanied by the formation of Ca? O, suggesting a chemical origin for the O 1s shift. By contrast, the C 1s peak shift toward a lower binding energy was observed relatively later, after about 4 Å of Ca deposition. At the same time, a new C 1s component became noticable at about ?1.5 eV relative to the initial C 1s peak. This component signifies the possibility of polymer disruption by the Ca atoms to form Ca? C species. The C 1s peak shift is attributed to Ca induced surface band bending and barrier formation as in the case of metal/PPV interface formation. The disruption of the polymer may also induce changes in the interface electronic states and contribute to the C 1s peak shift. From the intensity attenuation analysis, we conclude that the initial 15 Å of Ca overlayer is contaminated by the Ca? O and Ca? C species and the overlayer is pure beyond 15 Å of Ca coverage.     

Biodegradable studies of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone), poly(dioxanone), and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments

The aim of the study was to investigate the mechanical properties and biodegradability of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) [P(TMC‐ε‐CL)‐block‐PDO] in comparison with poly(p‐dioxanone) and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments in vivo and in vitro. P(TMC‐ε‐CL)‐block‐PDO copolymer and poly(p‐dioxanone) were prepared by using ring‐opening polymerization reaction. The monofilament fibers were obtained using conventional melt spun methods. The physicochemical and mechanical properties, such as viscosity, molecular weight, crystallinity, and knot security, were studied. Tensile strength, breaking strength retention, and surface morphology of P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl monofilament fibers were studied by immersion in phosphate‐buffered distilled water (pH 7.2) at 37°C and in vivo. The implantation studies of absorbable suture strands were performed in gluteal muscle of rats. The polymers, P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl, were semicrystalline and showed 27, 32, and 34% crystallinity, respectively. Those mechanical properties of P(TMC‐ε‐CL)‐block‐PDO were comparatively lower than other polymers. The biodegradability of poly(dioxanone) homopolymer is much slower compared with that of two copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 737–743, 2006     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Swelling behaviour of poly(α‐hydroxyacrylic acid) gel

Poly(α‐hydroxy acrylic acid) (PHA) and poly(acrylicacid) (PAA) gels were prepared by irradiating the respective 15 wt% aqueous solutions with γ‐rays. Swelling ratios for PHA gel were measured as a function of pH and divalent cation (Mg²⁺, Ca²⁺, Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺) concentration C₂ in the external solution to provide a comparison with the results for PAA gels. It was found that the swelling ratio of PHA gel steeply increases between pH 2 and 4, followed by a gradual swelling in the higher pH region. The corresponding steep swelling of PAA gel was observed at pH 3–6. Cation specificity in the equilibrium swelling ratio at a lower C₂ value (1.0 × 10⁻³ M) was approximately consistent with the binding selectivity in the solution system. Typically, the swelling ratio of PHA gel in the presence of Ca²⁺ was significantly lower than in the Mg²⁺ system, while the difference was slight for PAA gel. The response of the swelling ratio to changes in pH and C₂ was analysed as a first order relaxation to estimate the time constants. The (de)swelling kinetics measured by both the pH and C₂ jump were qualitatively interpreted in terms of main‐chain stiffness and intermolecular hydrogen bonding in the respective polymers. © 2000 Society of Chemical Industry