The thermal and mechanical properties of a polyurethane/multi-walled carbon nanotube composite

A polyurethane/multi-walled carbon nanotube elastomer composite was synthesized. The microstructure of the composite was examined by field-emission scanning electron microscopy and transmission electron microscopy. The thermal and mechanical properties of the composite were characterized by dynamic mechanical thermal analysis, thermogravimetric analysis and tensile testing. The chemical linkage of carbon nanotubes with polyurethane matrix was confirmed by Fourier transform infrared spectra. The study on the structure of the composite showed that carbon nanotubes could be dispersed in the polymer matrix well apart from a few of clusters. The results from thermal analysis indicated that the glass transition temperature of the composite was increased by about 10 °C and its thermal stability was obviously improved, in comparison with pure polyurethane. The investigation on the mechanical properties showed that the modulus and tensile strength could be obviously increased by adding 2 wt% (by weight) CNT to the matrix.     

Effects of carbon nanotube functionalization on the mechanical and thermal properties of epoxy composites

Chemically functionalized multi-walled carbon nanotube (MWCNT)/bisphenol-A glycidol ether epoxy resin/2-ethyl-4-methylimidazole composites were prepared. MWCNTs were first treated by a 3:1 (v/v) mixture of concentrated H₂SO₄/HNO₃, and then triethylenetetramine (TETA) grafting was carried out. X-ray photoelectron spectroscopy analysis proved the effectiveness of H₂SO₄/HNO₃ treatment and confirmed the TETA functionalization mechanism. Chemical functionalization decreases the crystalline content of MWCNTs, however, it did not greatly disrupt their structure. Transmission electron microscopy showed that there was a TETA thin layer on the MWCNT surface, which contributes to the homogenous dispersion of MWCNTs in epoxy matrix and the improvement of the MWCNT-epoxy interfacial interaction. Thus the impact strength, bending strength and thermal conductivity of the composites are enhanced.     

The effect of carbon nanotube properties on the degree of dispersion and reinforcement of high density polyethylene

The efficacy with which a range of nanotubes could reinforce a high density polyethylene (HDPE) matrix was investigated, in relation to nanotube diameter, purity, functionalization, alignment and nanotube bulk density. Composites were prepared by melt blending multiwall carbon nanotubes (MWNTs) with high density polyethylene (HDPE), followed by the injection molding of tensile specimens. At a 5 wt% loading, the most effective nanotubes were those of large diameter, received in an aligned form with low bulk density, producing a 66% increase in elastic modulus and a 69% improvement in yield stress. This was contradictory to theoretical mechanics calculations that predicted an increasing degree of reinforcement for nanotubes of reduced diameter. This difference was explained by the higher degree of dispersion observed in the composites with MWNTs of greater diameter.     

The effect of carbon nanotube hydrophobicity on the mechanical properties of carbon nanotube‐reinforced thermoplastic polyurethane nanocomposites

Double walled carbon nanotubes (DWNT) were functionalized by reacting methanol, dodecylamine, or octadecylamine with a toluene 2,4‐diisocyanate linker through a two‐stage reaction procedure. TGA coupled with FTIR analysis of both the decomposition products and the DWNT samples demonstrated that the functionalization procedure was successful and proceeded as expected for all samples. A preliminary investigation of the reinforcing capabilities of the functionalized DWNT in a thermoplastic polyurethane host polymer was then conducted. Tensile testing of the resultant nanocomposites demonstrated that the octadecylamine functionality provided the greatest enhancement in tensile strength and toughness. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheological and thermal properties of poly(ethylene oxide)/multiwall carbon nanotube composites

Poly(ethylene oxide) (PEO) based nanocomposites were prepared by the dispersion of multiwall carbon nanotubes (MWCNTs) in aqueous solution. MWCNTs were added up to 4 wt % of the PEO matrix. The dynamic viscoelastic behavior of the PEO/MWCNT nanocomposites was assessed with a strain‐controlled parallel‐plate rheometer. Prominent increases in the shear viscosity and storage modulus of the nanocomposites were found with increasing MWCNT content. Dynamic and isothermal differential scanning calorimetry studies indicated a significant decrease in the crystallization temperature as a result of the incorporation of MWCNTs; these composites can find applications as crystallizable switching components for shape‐memory polymer systems with adjustable switching temperatures. The solid‐state, direct‐current conductivity was also enhanced by the incorporation of MWCNTs. The dispersion level of the MWCNTs was investigated with scanning electron microscopy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synergetic effect of cyanogen functionalized carbon nanotube and graphene on the mechanical and thermal properties of poly (arylene ether nitrile)

Cyanogen functionalized carbon nanotube and graphene/poly (arylene ether nitrile) (CNT-CN/GN-CN/PEN) nanocomposite films were prepared by a facile solution casting method. The weight ratio of CNT-CN/GN-CN was varied from CNT-dominated to GN-dominated for the purpose of investigating their synergetic effects on the mechanical and thermal properties of PEN nanocomposites. Consequently, GN-CN/PEN composites demonstrated better mechanical and thermal properties than CNT-CN/PEN composites due to larger contact area between GN-CN and PEN matrix. Nevertheless, all CNT-CN/GN-CN/PEN composites exhibit enhanced mechanical properties than those of GN-only nanocomposites. With the increasing of CNT-CN/GN-CN weight ratio, the mechanical properties of CNT-CN/GN-CN/PEN composites increase, then decrease, and reach their maximums when CNT-CN/GN-CN weight ratio is around 4/4. From scanning electron microscope images, it is found that around that point GN-CN is flatly dispersed and CNT-CN is penetrated into GN-CN, capable of transferring stress load and thus decreasing interface loss. Thermal properties of CNT-CN/GN-CN/PEN composites once again confirmed the joint effect of CNT-CN and GN-CN, leading to improved thermal properties. In short, a synergistic effect between one-dimensional (1-D) CNT and two-dimensional (2-D) GN on the mechanical and thermal properties of nanocomposites have been demonstrated in these systems.     

Effect of phenol functionalized carbon nanotube on mechanical,dynamic mechanical,and thermal properties of isotactic polypropylene nanocomposites

In this work, multiwall carbon nanotubes (MWCNT) were functionalized with phenol and characterized by using Fourier transform infrared spectroscopy (FTIR). Isotactic polypropylene (iPP)/MWCNT composites of both the unfunctionalized and functionalized MWCNT were prepared by melt blending in a miniextruder at different loadings of nanotubes (i.e., 0.1, 0.25, 1.0, and 5.0 wt%). The tensile properties of the composites were found to increase with increase in nanotube loading with a maximum in Young's modulus being achieved at 1.0 wt% loading of phenol functionalized MWCNT. The differential scanning calorimetry (DSC) studies reveal the nucleating effect of MWCNT on the crystallization of iPP. Percentage crystallinity was found to increase on phenol functionalization of MWCNT. Results of X‐ray diffraction studies of the composites are in conformity with that of DSC studies. Dynamic mechanical studies reveal that the functionalized MWCNT causes many fold increase in the storage modulus, and the effect is pronounced in the case of functionalized MWCNT. POLYM. ENG. SCI. 2012. © 2011 Society of Plastics Engineers     

The effect of diameter on the mechanical properties of amorphous carbon fibres from linear low density polyethylene

Summary The mechanical properties of amorphous carbon fibres, derived from linear low density polyethylene strongly depend on the fibre diameter, which may be attributed to the presence of a skin/core structure in these fibres. High strength carbon fibres could thus be prepared by using thin precursor filaments, that are obtained by a melt-spinning process, in which the spinline is stretched at an elevated surrounding temperature. Careful carbonization of these precursors gives carbon fibres with a strength of 2.16 GPa, a modulus of 130 GPa and a high strain at break of 3%.     

Tuning the compressive mechanical properties of carbon nanotube foam

A post-growth chemical vapor deposition (CVD) treatment was used to tune the compressive mechanical properties of carbon nanotube (CNT) arrays. Millimeter tall CNT arrays with low compressive resilience were changed to a foam-like material with high compressive strength and almost complete recovery upon unloading. The foam was tuned to provide a range of compressive properties for various applications. The treated arrays demonstrated compressive strength up to 35× greater than the as-grown CNT array. Unlike polymeric foams, the CNT foam did not decompose after exposure to high temperatures. Investigation of the foam structure revealed that the CVD treatment increased CNT diameter through radial growth, while increasing the CNT surface roughness. The morphological changes help to explain the increase in CNT array compressive strength and the transition from permanent array deformation to foam-like recovery after compressive loading.     

Effect of gamma-irradiation on the mechanical properties of carbon nanotube yarns

Gamma-irradiation of carbon nanotube yarns in air has significantly improved the tensile strength and modulus of the yarns, presumably because of an increased interaction between the individual nanotubes. The improvement has been much greater for tightly structured yarns than for loosely structured yarns. Sonic pulse tests have also shown increased sound velocity and dynamic modulus in the carbon nanotube yarns as a result of gamma-irradiation treatment. X-ray photoelectron spectroscopic analyses on progenitor carbon nanotube forests show that gamma-irradiation treatment in air has dramatically increased the concentration of oxygen, for example as carboxyl groups, in the carbon nanotube assemblies in proportion to radiation dose, indicating that carbon nanotubes were oxidized under the ionizing effect of the gamma-irradiation. Such oxygen species are thought to contribute to the interaction between carbon nanotubes and thus to the improvement of carbon nanotube yarn mechanical properties.     

Effect of carbon nanotube length on thermal,electrical and mechanical properties of CNT/bismaleimide composites

Multi-wall carbon nanotubes (MWCNTs) with lengths of 0.65–1.3 mm were used to fabricate aligned and continuous MWCNT/bismaleimide composites. We found that longer CNTs resulted in higher thermal and electrical conductivities of the composites. The tensile strength and Young’s modulus, however, exhibited no CNT length dependency. Investigation of the CNT morphology by transmission electron microscopy revealed that the average nanotube diameter and wall number also increased with the CNT length, while the aspect ratio remained nearly unchanged. The structural changes significantly affected the phonon and electron transport in the composite structure, but the interplay of increased CNT length and diameter led to no appreciable change in the mechanical properties of the composites.     

Magnetically processed carbon nanotube/epoxy nanocomposites: Morphology, thermal, and mechanical properties

The processing-structure-property relationships of multiwalled carbon nanotubes (MWNTs)/epoxy nanocomposites processed with a magnetic field have been studied. Samples were prepared by dispersing the nanotube in the epoxy and curing under an applied magnetic field. The nanocomposite morphology was characterized with Raman spectroscopy and wide angle X-ray scattering, and correlated with thermo-mechanical properties. The modulus parallel to the alignment direction, as measured by dynamic mechanical analysis, showed significant anisotropy, with a 72% increase over the neat resin, and a 24% increase over the sample tested perpendicular to the alignment direction. A modest enhancement in the coefficient of thermal expansion (CTE) parallel to the alignment direction was also observed. These enhancements were achieved even though the nanotubes were not fully aligned, as determined by Raman spectroscopy. The partial nanotube alignment is attributed to resin a gel time that is faster than the nanotube orientation dynamics. Thermal conductivity results are also presented.     

Fabrication and mechanical properties of carbon nanotube yarns spun from ultra-long multi-walled carbon nanotube arrays

Carbon nanotube (CNT) yarns have been fabricated by dry spinning from vertically aligned millimeter-long multi-walled carbon nanotube (MWCNT) arrays and their mechanical properties have been studied. By using 2-mm long CNTs and densely packing of CNT yarns we achieved a tensile strength of 1068 MPa and Young’s modulus of 55 GPa. Our CNT yarns have diameters of tens of micrometers being easy to handle and possessing high effective load capacity up to 0.81 N. We discuss mechanical properties of CNT yarns spun from relatively thick MWCNT along with a detailed analysis of various post-spin processes and their effect on CNT yarns characteristics. Also, we point out the difference between mechanical properties of dry spun CNT yarns and conventional spun textile yarns.     

Predicted mechanical properties of a coiled carbon nanotube

Nanostructured carbon materials continue to attract much interest for use in devices and as fillers in composites. Here, classical molecular dynamics simulations are carried out using many-body empirical potentials to contrast the mechanical properties of straight and coiled carbon nanotubes. The specific properties of a coiled carbon nanotube (CCNT) are investigated under compression, tension, re-compression, re-tension and pullout from a polyethylene (PE) matrix. The stress–strain curves, spring constants, and yielding strains under compression and tension are given for each system, and the corresponding reasons for the differences in their behavior are discussed. They indicate that the interaction between a CCNT and a PE matrix is stronger than the corresponding interactions between CNTs and PE. Thus, the results indicate that CCNTs are good potential candidates for lightweight, tough composites.     

Quantification of carbon nanotube dispersion and its correlation with mechanical and thermal properties of epoxy nanocomposites

An experimental study is carried out to quantitatively assess the dispersion quality of carbon nanotubes (CNTs) in epoxy matrix as a function of CNT variant and weight fraction. To this end, two weight fractions (0.05% and 0.25%) of as-grown, oxidized, and functionalized CNTs are used to process CNT/epoxy nanocomposites. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared analysis of different variants of CNTs are used to establish the efficiency of purification route. While the relative change in mechanical properties is investigated through tensile and micro-hardness testing, thermal conductivity of different nanocomposites is measured to characterize the effect of CNT addition on the average thermal properties of epoxy. Later on, a quantitative analysis is carried out to establish the relationship between the observed improvements in average composite properties with the dispersion quality of CNTs in epoxy. It is shown that carboxylic (-COOH) functionalization reduces the average CNT agglomerate size and thus ensures better dispersion of CNTs in epoxy even at higher CNT weight fraction. The improved dispersion leads to enhanced interfacial interaction at the CNT/epoxy interface and hence provides higher relative improvement in nanocomposite properties compared to the samples prepared using as-grown and oxidized CNTs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48879.     

Ultrasonication effects on thermal and rheological properties of carbon nanotube suspensions

The preparation of nanofluids is very important to their thermophysical properties. Nanofluids with the same nanoparticles and base fluids can behave differently due to different nanofluid preparation methods. The agglomerate sizes in nanofluids can significantly impact the thermal conductivity and viscosity of nanofluids and lead to a different heat transfer performance. Ultrasonication is a common way to break up agglomerates and promote dispersion of nanoparticles into base fluids. However, research reports of sonication effects on nanofluid properties are limited in the open literature. In this work, sonication effects on thermal conductivity and viscosity of carbon nanotubes (0.5 wt%) in an ethylene glycol-based nanofluid are investigated. The corresponding effects on the agglomerate sizes and the carbon nanotube lengths are observed. It is found that with an increased sonication time/energy, the thermal conductivity of the nanofluids increases nonlinearly, with the maximum enhancement of 23% at sonication time of 1,355 min. However, the viscosity of nanofluids increases to the maximum at sonication time of 40 min, then decreases, finally approaching the viscosity of the pure base fluid at a sonication time of 1,355 min. It is also observed that the sonication process not only reduces the agglomerate sizes but also decreases the length of carbon nanotubes. Over the current experimental range, the reduction in agglomerate size is more significant than the reduction of the carbon nanotube length. Hence, the maximum thermal conductivity enhancement and minimum viscosity increase are obtained using a lengthy sonication, which may have implications on application.     

The effect of multiwalled carbon nanotube agglomeration on their accumulation in and damage to organs in mice

Purified carboxylated multiwalled carbon nanotubes (MWCNTs) with different agglomeration propensities were evaluated in mice following a single dose intravenous injection. Both agglomerated and the well suspended MWCNTs were taken up by mononuclear phagocyte system organs. MWCNTs with higher degree of agglomeration were retained in lungs and later in the liver and were not eliminated completely in 28 days, while the well-dispersed ones remained well dispersed and formed fewer aggregates in the lungs and liver, and seemed to be easily eliminated. Persistent accumulation of agglomerated MWCNTs in the lungs caused inflammatory responses while the well-suspended ones did not. Although the elimination of MWCNTs is still to be evaluated quantitatively, the formation of a stable suspension is one of the key requirements for safe applications in medicine.     

Morphology,thermal stability,and dynamic mechanical properties of atactic polypropylene/carbon nanotube composites

Nanocomposites based on atactic polypropylene (aPP) and multiwall carbon nanotubes were prepared by melt blending at 80°C with a Barabender mixer. The morphology, thermal stability, and dynamic mechanical properties of the obtained composites were studied subsequently. SEM observations indicate that the nanotubes are well dispersed in the aPP matrix. Each nanotube is covered by a layer of aPP molecules. Thermal stability of the aPP in nitrogen is found to be enhanced significantly by the addition of nanotubes. Peak temperature of the DTG curve for the nanocomposite with 5 wt % nanotube loading shows about 70°C higher than that of pure aPP. Dynamic mechanical properties of aPP are also influenced by nanotubes, as shown by the increase in the storage modulus as well as significantly broadened loss tanδ peak. These effects of nanotubes on the thermal stability and mechanical properties of aPP are explained by the adsorption effect of the aPP molecules on the nanotube surfaces in this study. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1087–1091, 2005     

Synthesis and mechanical properties of carbon nanotube/diamond-like carbon composite films

Diamond-like carbon (DLC) coatings were successfully deposited on carbon nanotube (CNT) films with CNT densities of 1 × 10⁹/cm², 3 × 10⁹/cm², and 7 × 10⁹/cm² by a radio frequency plasma-enhanced chemical vapor deposition (CVD). The new composite films consisting of CNT/DLC were synthesized to improve the mechanical properties of DLC coatings especially for toughness. To compare those of the CNT/DLC composite films, the deposition of a DLC coating on a silicon oxide substrate was also carried out. A dynamic ultra micro hardness tester and a ball-on-disk type friction tester were used to investigate the mechanical properties of the CNT/DLC composite films. A scanning electron microscopic (SEM) image of the indentation region of the CNT/DLC composite film showed a triangle shape of the indenter, however, chippings of the DLC coating were observed in the indentation region. This result suggests the improvement of the toughness of the CNT/DLC composite films. The elastic modulus and dynamic hardness of the CNT/DLC composite films decreased linearly with the increase of their CNT density. Friction coefficients of all the CNT/DLC composite films were close to that of the DLC coating.     

Impact of compression molding conditions on the thermal and mechanical properties of polyethylene

Compression molding is a current technique in polymer processing. Despite numerous studies, effect of molding pressure on physical properties has surprisingly not been fully investigated. In this study, the thermal and mechanical behavior of the compression‐molded polyethylene were thus explored to better grasp the relationship between processing parameters and ensuing properties. The effect of the molding temperature, pressure, cooling rate, and temperature profile on the tensile and flexural moduli as well as melting point of polyethylene was studied. We conclude that higher tensile and flexural moduli are obtained by increasing pressure and molding temperature, as well as decreasing the cooling rate. Our results were corroborated by X‐ray diffraction and differential scanning calorimetry measurements. Moreover, the use of a temperature gradient with different temperatures for the upper and bottom plates of the mold leads to asymmetric samples whose tensile and flexural moduli are improved. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46176.