Mechanical properties and water absorption of fiber‐reinforced polypropylene composites prepared by bagasse and beech fiber

The present study investigates the tensile, flexural, notched Izod impact, and water absorption properties of bagasse and beech reinforced polypropylene (PP) composites as a function of fiber content. The surface of fibers was modified through the use of maleated polypropylene (MAPP) coupling agent. From this study, it was found that mechanical properties increase with an increase in fiber loading in both cases. However, the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading was evaluated and found maximum for the BA/PP composites. The weight gains for all specimens were less than 7%. In general, the results showed the usefulness of bagasse fiber as a good alternative and reinforcing agent for composite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Fundamental studies on wood–plastic composites: Effects of fiber concentration and mixing temperature on the mechanical properties of poplar/PP composite

Wood fibers are increasingly being used as reinforcement in commercial thermoplastic composites due to their low cost, high specific properties and renewable nature. The ultimate goal of our research was to find a fundamental understanding of the mechanical behavior of poplar/polypropylene (PP) composites. The effect of wood fiber concentrations and mixing temperature on the mechanical properties of composites, prepared by using MAPP as the coupling agent, was investigated. In the sample preparation, four levels of fiber loading (10, 20, 30, and 40 wt%) and three compounding temperatures (180, 190, and 200^oC) were used. Most major changes in composite performance occurred at fiber contents above 30%. The results clearly showed that the fiber loading of 30 and 40 wt% at 190^oC was provided adequate reinforcement to increase the tensile and flexural strength of the PP powder. The modulus also increased with increasing the fiber content, because poplar fibers are believed to be more rigid than polymer. However the addition of wood fibers resulted in a decrease in elongation and impact properties of the composites. The FTIR spectroscopy showed that the copolymer was bonded to the fibers by ester linkages and hydrogen bonds at 1705–1735 cm⁻¹. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Banana/Glass Fiber-Reinforced Polypropylene Hybrid Composites: Fabrication and Performance Evaluation

Hybrid composites of Polypropylene (PP) reinforced with intimately mixed short banana and glass fibers were fabricated using Haake twin screw extruder followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both the fibers into PP matrix resulted in an increase in tensile, flexural and impact strength with an increasing level of fiber content upto 30 wt% at banana: glass fiber ratio of 15:15 wt% and 2 wt% of MAPP. The rate of water absorption for the hybrid composites decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has also been analyzed to investigate the interfacial properties. An increase in the storage modulus (E′) of the treated composite indicates higher stiffness. The tan δ spectra confirms a strong influence of fiber contents and coupling agent on the α and β relaxation processes of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out employing differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA) which indicated a decrease in the crystallization temperature and thermal stability of PP with the incorporation of MAPP treated banana and Glass fiber.     

Moisture uptake and hygroexpansion of wood fiber composite materials with polylactide and polypropylene matrix materials

Effects of butantetracarboxylic acid (BTCA) modification, choice of matrix, and fiber volume fraction on hygroexpansion of wood fiber composites have been investigated. Untreated reference wood fibers and BTCA‐modified fibers were used as reinforcement in composites with matrices composed of polylactic acid (PLA), polypropylene (PP), or a mixture thereof. The crosslinking BTCA modification reduced the out‐of‐plane hygroexpansion of PLA and PLA/PP composites, under water‐immersed and humid conditions, whereas the swelling increased when PP was used as matrix material. This is explained by difficulties for the BTCA‐modified fibers to adhere to the PP matrix. Fiber volume fraction was the most important parameter as regards out‐of‐plane hygroexpansion, with a high‐fiber fraction leading to large hygroexpansion. Fiber‐matrix wettability during processing and consolidation also showed to have a large impact on the dimensional stability and moisture uptake. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Jute fiber reinforced polypropylene produced by continuous extrusion compounding,part 1: Processing and ageing properties

This article addresses the processing and ageing properties of jute fiber reinforced polypropylene (PP) composites. The composite has been manufactured by a continuous extrusion process and results in free flowing composite granules, comprising up to 50 weight percent (wt %) jute fiber in PP. These granules have similar shape and diameter as commercially available PP granules. Rheological analysis shows that viscosity of the compounds follows the same shear rate dependency as PP and is on the same level as glass‐PP compounds. The mechanical properties show very little variation and exhibit strength and stiffness values at the upper range of competing natural fiber reinforced compounds for injection molding. The mechanical performance reduces gradually upon prolonged thermal loading and immersion in water. The low water diffusion coefficient of the 50 wt % jute‐PP composites indicates that the fibers are not forming a continuous network throughout the polymer. The jute fibers exhibit a stabilizing effect against ultra violet irradiation (UV) on PP polymer and, as a consequence, the mechanical properties of jute‐PP composites hardly decrease during an accelerated UV ageing test. Bacteria, fungi, and garden mold grow easily on the compound material, but only have a limited effect on mechanical properties. The resistance to growth of bacteria on the materials surface can be increased using a biostabilizer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study of effect of old corrugated cardboard in properties of polypropylene composites: Study of mechanical properties,thermal behavior,and morphological properties

The investigation of the economical use of lignocellulose waste, which is one of the environmental problems facing nations, is ongoing. In this study, waste cardboard paper fiber reinforcing polypropylene (PP) composites was developed. In order to modify the PP matrix maleated PP (MA‐g‐PP) a 5 wt% and a grafting rate of 1 and 2 wt% was used as a compatibilizer. The effects of fiber and compatibilizer content as well as graft content are evaluated by mechanical, thermal property measurements, and scanning electron microscopy (SEM). The compatibilizer improved all mechanical properties significantly. Thus, the tensile strength of MA‐g‐PP‐containing composites increases compared to PP/cardboard composites paper content increases. However, the tensile modulus of a PP‐based composite increases with an increase in paper fiber with the compatibilizer having little effect. SEM revealed that the addition of MA‐g‐PP generates strong interactions between a PP matrix and paper fibers. However, the addition of the MA‐g‐PP compatibilizing agent gives a significant improvement on the crystallization of the composites, whereas the compatibilized PP/old corrugated cardboard (OCC) composites have higher crystallinity (Xc) than uncompatibilized PP/OCC composites. The MA‐g‐PP also diminished the water absorption in the composites. J. VINYL ADDIT. TECHNOL., 22:231–238, 2016. © 2014 Society of Plastics Engineers     

Isolation and characterization of betel nut leaf fiber: Its potential application in making composites

Betel nut leaf fiber (BNLF) is a new finding as cellulosic filler for polymer composites. Its main constituents are 75% α‐cellulose, 12% hemicelluloses, 10% lignin, and 3% others matter, viscosity average molecular weight 132,000 and degree of crystallinity 70%. In the present work, BNLF reinforced polypropylene (PP) composites were prepared using heat press molding method. 5–20 wt% short length fiber is taken for getting benefits of easy manufacturing and the fiber was chemically treated with NaOH, dicumyl peroxide (DCP), and maleic anhydride‐modified PP (MAPP) to promote the interfacial bond with PP. The extent of modification of fiber was assessed on the basis of morphology, bulk density, moisture absorption, thermal, and mechanical properties of untreated fiber, treated fiber, and their reinforcing PP composites. The tensile and flexural strength of composites increase with the increase of fiber loading up to 10 and 20 wt%, respectively. It was also observed that Young's modulus and flexural modulus increase with fiber loading. The thermal degradation behavior of resulting composites was investigated. Among the various treated fibers, MAPP‐treated fiber composite showed best interfacial interactions as well as mechanical and thermal properties. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Influence of interfacial adhesion on the structural and mechanical behavior of PP‐banana/glass hybrid composites

Hybrid composites of polypropylene (PP), reinforced with short banana and glass fibers were fabricated using Haake torque rheocord followed by compression molding with and without the presence maleic anhydride grafted polypropylene (MAPP) as a coupling agent. Incorporation of both fibers into PP matrix resulted in increase of tensile strength, flexural strength, and impact strength upto 30 wt% with an optimum strength observed at 2 wt% MAPP treated 15 wt% banana and 15 wt% glass fiber. The rate of water absorption for the hybrid composites was decreased due to the presence of glass fiber and coupling agent. The effect of fiber loading in presence of coupling agent on the dynamic mechanical properties has been analyzed to investigate the interfacial properties. An increase in storage modulus (E′) of the treated‐composite indicates higher stiffness. The loss tangent (tan δ) spectra confirms a strong influence of fiber loading and coupling agent concentration on the α and β relaxation process of PP. The nature of fiber matrix adhesion was examined through scanning electron microscopy (SEM) of the tensile fractured specimen. Thermal measurements were carried out through differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA), indicated an increase in the crystallization temperature and thermal stability of PP with the incorporation of MAPP‐treated banana and glass fiber. POLYM. COMPOS., 31:1247–1257, 2010. © 2009 Society of Plastics Engineers     

Bamboo fiber reinforced polypropylene composites and their mechanical,thermal, and morphological properties

Short bamboo fiber reinforced polypropylene composites were prepared by incorporation of various loadings of chemically modified bamboo fibers. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as compatibilizer to improve fiber–matrix adhesion. The effects of bamboo fiber loading and modification of the resin on the physical, mechanical, thermal, and morphological properties of the bamboo reinforced modified PP composites were studied. Scanning electron microscopy studies of the composites were carried out on the interface and fractured surfaces. Thermogravimetric analysis and IR spectroscopy were also carried out. At 50% volume fraction of the extracted bamboo fiber in the composites, considerable increase in mechanical properties like impact, flexural, tensile, and thermal behavior like heat deflection temperature were observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

All‐straw‐fiber composites: Benzylated straw as matrix and additional straw fiber reinforced composites

With the aim to utilize the waste biomass of wheat straw, all‐straw‐fiber composites were elaborately manufactured though producing plastic benzylated wheat straw (BWS) as matrix and reinforced by additional straw fibers (ASF). The extent of benzylation for wheat straw was greatly improved with the aid of ball milling pretreatment for 4 h. BWS yielded higher weight percent gain (WPG) under the same reaction conditions with the benzylation of wood flour, lower glass transition temperature (T_g) as well as better flowability upon heating compared to benzylated mulberry branches (BMB) with comparable WPG. All‐straw‐fiber composites performed higher ASF loading capacity and better mechanical properties with optimum ASF content than BMB based composites and by benzylation decreased water absorption significantly. SEM provided evidence for strong adhesion in the interface between BWS and ASF. From the overall performance, the All‐straw‐fiber composites can be regarded as a potential alternative to wood plastic composites. POLYM. COMPOS., 35:419–426, 2014. © 2013 Society of Plastics Engineers     

Mechanical performance and moisture absorption of various natural fiber reinforced thermoplastic composites

Natural fibers are seeing increased use in composite applications due to their reduced cost, low density, and environmental benefits (more sustainable and lower carbon footprint). Although many natural fiber systems have been examined over the last decade, there have been relatively few studies which have compared a variety of fiber types and processing methods directly in the same experimental set. In this study, natural fiber composites made from low density polyethylene (LDPE) and a variety of Canadian based fiber feedstocks were examined including hemp bast, flax bast, chemically pulped wood, wood chips, wheat straw, and mechanically pulped triticale. The effect of fiber type, fiber fraction and maleic anhydride polyethylene (MAPE) coupling agent on the mechanical properties and long‐term moisture absorption behavior was quantified. In general, addition of natural fiber to LDPE results in an increase in modulus (stiffness) with a corresponding loss of material elongation and impact toughness. Of the fiber types tested, composites made from chemically pulped wood had the best mechanical properties and the least moisture absorption. However, the use of MAPE coupling agent was found to significantly increase the mechanical performance and reduce moisture absorption for all other natural fiber types. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 969‐980, 2013     

Effect of chemical treatment on the properties of coir fiber reinforced polypropylene and polyethylene composites

Chemical treatment of reinforcement material is one of the main ways of improving the mechanical properties of natural fiber reinforced polymer composites. In the present study, coir fiber was used as reinforcement material, while polypropylene (PP) and polyethylene (PE) polymer were used as matrix material. Before reinforcing with polymer, raw coir fiber was chemically treated with basic chromium sulfate and sodium bicarbonate in a sieve shaker. Hot‐pressed method was used for composite manufacturing during which the fiber loading was varied at 0, 5, 10, 15, and 20 wt%. Comparison of the properties of raw and chemically treated coir fiber reinforced PP and PE was conducted. Mechanical characteristics of the composites were evaluated using tensile, flexural, impact, and hardness tests. Water absorption test was conducted to know water uptake characteristics. Microstructural analysis using a scanning electron microscope was performed to observe the adhesiveness between the matrix and the fiber. Thermogravimetric analysis was done to observe the physical and chemical changes in fiber and composites. The results showed that chemical treatment improved the physical, mechanical, and thermal properties of the manufactured composites. PP composites had better properties as compared to PE composites, while higher fiber loading resulted in better mechanical properties of the resultant composites. POLYM. COMPOS., 38:1259–1265, 2017. © 2015 Society of Plastics Engineers     

Studies on mechanical characterization and water resistance of glass fiber/thermoplastic polymer bionanocomposites

This experimental work is aimed at studying the performance of rice husk flour/glass fiber reinforced high density polyethylene hybrid nanocomposites. To meet this objective, the nanoclay was compounded with high density polyethylene (HDPE), rice husk flour (RF), glass fiber, and coupling agent in an internal mixer; then, the samples were fabricated by injection molding. The concentration was varied from 0 to 6 per hundred compounds for nanoclay and from 0 to 15% for glass fiber, individually. The amount of coupling agent was fixed at 2% for all formulations. The morphology, water absorption, thickness swelling, and mechanical properties of nanocomposites were evaluated as a function of nanoclay and glass fiber contents. The results indicated that both modulus and strength were improved when glass fibers were added to the composites system but impact strength and moisture absorption further decreased with the increase of glass fiber content. The morphology of the nanocomposites has been examined by using X‐ray diffraction. The morphological findings revealed that the nanocomposites formed were intercalated. The mechanical analysis showed that the biggest improvement of the tensile and flexural modulus and strengths can be achieved for the nanoclay loading at 4 per hundred compounds. However, further increasing of the loading of nanoclay resulted in a decrease of impact strength. Finally, it was found that addition of nanoclay reduced the water absorption and thickness swelling of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of the delignification of wood fibers on the mechanical properties of wood fiber–polypropylene composites

The effect of the delignification of hornbeam fibers on the mechanical properties of wood fiber–polypropylene (PP) composites was studied. Original fibers and delignified fibers at three levels of delignification were mixed with PP at a weight ratio of 40:60 in an internal mixer. Maleic anhydride (0.5 wt %) as the coupling agent and dicumyl peroxide (0.1 wt %) as the initiator were applied. The produced composites were then hot‐pressed, and specimens for physical and mechanical testing were prepared. The results of the properties of the composite materials indicate that delignified fibers showed better performance in the enhancement of tensile strength and tensile modulus, whereas the hardness of the composites was unaffected by delignification. Delignified fibers also exhibited better water absorption resistance. Notched impact strength was higher for delignified fiber composites, but it was reduced at higher delignification levels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4759–4763, 2006     

Diffusion of water and artificial seawater through coir fiber reinforced natural rubber composites

The diffusion of water and artificial seawater through cross‐linked coir fiber reinforced natural rubber composites was analyzed. The effect of fiber loading, chemical treatment, and bonding agent on liquid sorption was investigated. Based on the experiments, it is suggested that the probable mechanism of transport in gum compound is Fickian and that in composites is anomalous. The liquid uptake of all the composites is higher in water than that in artificial seawater. The composites showed increased swelling with fiber loading in water and artificial seawater. The influence of silica in the bonding system on swelling of the composites was also analyzed. In the case of gum compound, the desorption process is also Fickian, similar to the absorption of water and seawater. But the desorption of composites exhibited deviation from Fickian behavior. The effect of chemical treatment of coir fibers on the swelling was analyzed and found that the uptake of water and artificial seawater is reduced further in composites containing treated fibers. POLYM. COMPOS., 26:136–143, 2005. © 2005 Society of Plastics Engineers     

Influence of varying fiber lengths on mechanical,thermal, and morphological properties of MA‐g‐PP compatibilized and chemically modified short pineapple leaf fiber reinforced polypropylene composites

Environmentally benign, low cost and abundantly available short pineapple leaf fibers (PALF), found mostly in the Tropical rain forest climates are ideal materials for manufacture of thermoplastic polymer‐matrix composites. Here, mechanical and thermal properties of composites of maleic anhydride grafted polypropylene (MA‐g‐PP) and chemically modified short PALF are studied as a function of different fiber lengths at 10 vol % fibers loading with fiber orientation in the longitudinal direction. The effects of fiber lengths and fiber loading on the morphological properties are assessed via observations by scanning electron microscopy. Fiber length of 6 mm oriented longitudinally at 10 vol % fibers loading in PP is the optimum and recommended composition, where 73% increase in impact properties, 37% increase in the flexural modulus, 33% increase in flexural strength, and 14% increase in vicat softening temperature are observed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of LDPE and PP—Wood fiber composites

Natural fiber reinforced composites is an emerging area in polymer science. These natural fibers are low cost fibers with low density and high specific properties. These are biodegradable and nonabrasive. The natural fiber composites offer specific properties comparable to those of conventional fiber composites. However, in development of these composites, the incompatibility of the fibers and poor resistance to moisture often reduce the potential of natural fibers, and these draw backs become critical issue. Wood‐plastic composites (WPC) are a relatively new class of materials and one of the fastest growing sectors in the wood composites industry. Composites of wood in a thermoplastic matrix (wood–plastic composites) are considered a low maintenance solution to using wood in outdoor applications. WPCs are normally made from a mixture of wood fiber, thermoplastic, and small amounts of process and property modifiers through an extrusion process. In this study, Wood–plastic composites (WPC) are produce by adding a maleic anhydride modified low density polyethylene coupling agent to improve interfacial adhesion between the wood fiber and the plastic. Mixing is done with twin screw extruder. Subsequently, tensile strength, the modulus of elasticity, % elongation, hardness, Izod impact strength, melt flow index (MFI), and heat deflection temperature (HDT) are determined. Thermal transition temperatures and microstructure are determined with DSC and SEM, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Absorption of water at ambient temperature and steam in wood–polymer composites prepared from agrowaste and polystyrene

Hemp, banana, and agave fibers were employed for the preparation of wood–polymer composites using polystyrene in the ratio of 50 : 50 w/w. These fibers were esterified with maleic anhydride (MA) and the effect of MA was studied on the absorption of water at ambient temperature and steam in wood–polymer composites made from said fibers and polystyrene. The absorption of water increases with increase in time from 2 to 30 h in all fiber composites. The maximum absorption of water was found in hemp fiber composites, and the minimum in agave fiber composites. The MA-esterified fiber composites showed less absorption of water than did the untreated fiber composites. Steam absorption in MA-treated and untreated fiber composites is higher than the water absorption in the respective fiber composites. Untreated fiber composites show more absorption of steam in comparison to MA-treated fibers composites. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 681–686, 1998     

Preparation and properties of successive alkali treated completely biodegradable short jute fiber reinforced PLA composites

The natural fiber reinforced biodegradable polymer composites were prepared with short jute fiber as reinforcement in PLA (Poly lactic acid) matrix. The short jute fiber is successively treated with NaOH at various concentrations (5%, 10%, and 15%) and H₂O₂. The composites were prepared with untreated and treated short jute fibers at different weight proportions (up to 25%) in PLA and investigated for mechanical properties. The results showed that the composite with successive alkali treated jute fiber at 10% NaOH and H₂O₂ with 20% fiber loading has shown 18% higher flexural strength than neat PLA and untreated jute/PLA composite. The flexural modulus of the composite at 25% fiber loading was 125% and 110% higher than that of composites with untreated fibers and neat PLA, respectively. The impact strength of composite with untreated fibers at higher fiber weight fraction was 23% high as compared to neat PLA and 26% high compared to composite with treated fibers. The water absorption was more for untreated jute/PLA composite at 25% fiber loading than all other composites. The composite with untreated fibers has high thermal degradation compared with treated fibers but lower than that of pure PLA matrix. The enzymatic environment has increased the rate of degradation of composites as compared to soil burial. Surface morphology of biodegraded surfaces of the composites were studied using SEM method. POLYM. COMPOS., 37:2160–2170, 2016. © 2015 Society of Plastics Engineers     

Effect of fiber pretreatment condition on the interfacial strength and mechanical properties of wood fiber/PP composites

The effect of fiber surface pretreatment on the interfacial strength and mechanical properties of wood fiber/polypropylene (WF/PP) composites are investigated. The results demonstrate that fiber surface conditions significantly influence the fiber–matrix interfacial bond, which, in turn, determines the mechanical properties of the composites. The WF/PP composite containing fibers pretreated with an acid–silane aqueous solution exhibits the highest tensile properties among the materials studied. This observation is a direct result of the strong interfacial bond caused by the acid/water condition used in the fiber pretreatment. Evidence from coupling chemistry, rheological and electron microscopic studies support the above conclusion. When SEBS‐g‐MA copolymer is used, a synergistic toughening effect between the wood fiber and the copolymer is observed. The V‐notch Charpy impact strength of the WF/PP/SEBS‐g‐MA composite is substantially higher than that of the WF/PP composite. The synergistic toughening mechanisms are discussed with respect to the interfacial bond strength, fiber‐matrix debonding, and matrix plastic deformation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1000–1010, 2000