Probing the compatibility and interaction of energetic binders based on 3,3‐bis(azidomethyl)oxetane with some explosives: thermal,interfacial and simulation studies

Several polymer binders based on 3,3‐bis(azidomethyl)oxetane (BAMO) were studied to explore the compatibility and interaction of the energetic binders with three common energetic oxidants. The compatibilities were studied by differential scanning calorimetry and ratings were obtained according to evaluated standards. The results showed that all the binders based on BAMO had good compatibility with cyclotrimethylenetrinitramine, cyclotetramethylenetetranitroamine and hexanitrohexazaiso‐wurtzitane. The work of adhesion (W_a) between binders and explosives was tested via measurement of contact angle and the results are in the following order: chain‐extended poly(3,3‐bis(azidomethyl)oxetane) (PBAMO) by isophorone diisocyanate (IPDI‐CE) with diethyl bis(hydroxymethyl) malonate (IPDI‐DBM‐CE) > chain‐extended PBAMO by IPDI‐CE > PBAMO. In addition, similar results were found in the binding energies reported by molecular dynamics, and the average values of E_binding for the IPDI‐DBM‐CE system were larger than E_binding for the other systems due to the formation of hydrogen bonds between –COOEt and –NO₂, which improve the bonding abilities. © 2017 Society of Chemical Industry     

Reactive surfactants in heterophase polymerization. VI. Synthesis and screening of polymerizable surfactants (surfmers) with varying reactivity in high solids styrene—butyl acrylate—acrylic acid emulsion polymerization

Several polymerizable surfactants (surfmers) have been used in the semi-continuous emulsion copolymerization of styrene, butyl acrylate, and acrylic acid. Three of the (anionic) surfmers (sodium 11-crotonoyl undecan-1-yl sulfate, sodium 11-methacryloyl undecan-1-sulfate, and sodium sulfopropyl tetradecyl maleate) were prepared in house with purities between 53 and 82%. Physicochemical properties such as the critical micelle concentration, the adsorption isotherm, and the specific adsorption area were determined. The surfmers were then used with constant addition profiles in semicontinuous reactions, and the instantaneous conversions of the main monomers determined. The particle size, amount of coagulum, surface tension, and stability against electrolyte solutions of the latices were evaluated. Films were cast of some of the latices, and the visual appearance and water adsorption were assessed. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 183–1820, 1997     

Optically transparent aromatic poly(ester imide)s with low coefficients of thermal expansion. 2: Effect of the introduction of alkyl‐substituted p‐biphenylene units

A series of ester‐linked tetracarboxylic dianhydrides (TA‐X) were synthesized from trimellitic anhydride chloride and 4,4′‐biphenol analogs containing different numbers and positions of methyl substituents. Aromatic poly(ester imide)s (PEsIs) were polymerized from TA‐Xs and 2,2′‐bis(trifluoromethyl)benzidine to investigate the film properties systematically. A significant substituent effect on the target properties (T_g, optical transparency, the linear coefficient of thermal expansion (CTE) and ductility) was observed. A PEsI containing 2,2′,3,3′,5,5′‐hexamethyl‐substituted p‐biphenylene units was chemically imidized in a homogeneous state. It was highly soluble at room temperature, even in less hygroscopic non‐amide solvents such as cyclopentanone (CPN), and provided a stable CPN solution with a high solid content. The CPN‐cast PEsI film was almost colorless as suggested from the rather low yellowness index (3.2), high light transmittance at 400 nm (71.5%) and very low haze (1.15%). This PEsI film also had a high T_g (294 °C, determined by thermomechanical analysis) in addition to a low CTE (21.7 ppm K^?1), moderate film ductility and very low water uptake. A structural modification of the PEsI by copolymerization with a tetracarboxylic dianhydride with a rigid/linear structure was effective in further reducing the CTE while maintaining the other excellent target properties. Thus, some of the PEsIs developed in this work are promising candidates as novel plastic substrates for use in image display devices. © 2017 Society of Chemical Industry