Specific features of the phase transformations occurring during the sintering process of the beta-alumina based ceramics and their properties

Conclusions During the sintering process of beta-alumina obtained using the method of plasmochemical synthesis, the structural transformation occurs and it is accompanied by the separation of the excess Na₂O and the formation of an intergranular meltlike phase that is saturated with sodium and is characterized by high dielectric properties.The quantity of the meltlike phase and the magnitude of the /( + ) ratio determine the degree of stabilization (stability) and the final resistivity of the material and depend on the initial chemical composition and the heating rate maintained during the sintering process.It was shown that when the duration of residence of the material in the hot zone of the furnace is increased or when the specimens sintered maintaining high heating rates are subjected to additional heat treatment, one observes the occurrance of the reverse structural transformation that is characterized by an increase of the phase ratio /( + ) 1, a reduction in the quantity of the meltlike phase right up to its complete disappearance, and a decrease of the electrical resistivity of the material.In the materials having a large excess quantity of sodium oxide, the process of crystallization of the intergranular NaAlO₂ phase occurs simultaneously with the second phase transformation.The best ceramic and electrophysical parameters were obtained when sintering the material contained 7.9% Na₂O.Translated from Ogneupory, No. 3, pp. 13–18, March, 1990.     

Synthesis of statistical polydiene networks by reaction of liquid polyenes with telechelic siloxanes

The present investigation concerns the synthesis of statistical networks similar to vulcanized rubber. We have used liquid precursor polymers: polybutadiene (PB) and polyisoprene (PI) with telechelic siloxanes. The reactivity of the polydienes can be classified as follows: PB units 1,2 PI units 3,4 PI units 1,4 0. The network formation is a function of the ratio R = nb, of pendent double bonds/nb. of SiH. For R 1 the networks are rather hard and brittle, for 8 R 10 they are soft and elastic, whereas for R 16 the gels obtained are very soft and sticky.     

A study of the influence of the synthesis conditions upon the catalytic properties of silicoaluminophosphate molecular sieves

The skeletal isomerization of 1butene was performed over a series of silicoaluminophosphate molecular sieves with AEL structure (SAPO11). The results were compared with those obtained over an aluminophosphate molecular sieve (AlPO₄11). The three SAPO11 samples, with different acidic properties, were synthesized by either varying the chemical composition of the synthesis gel or by varying the preparation time of the aforementioned gel. The catalytic results indicate that irrespective of how the acidity of the SAPO11 samples is changed (viz., independently of the method elected to modify the acidic properties of the samples), a close parallelism between the selectivity towards the skeletal isomerization and the number of (moderate + strong) Brønsted acid sites (sites retaining pyridine above 623 K) was observed for the SAPO11 solids. These results, definitively, indicate the participation of these acid sites in the skeletal isomerization process.     

Antifungal polyoxygenated fatty acids fromAeollanthus parvifolius

Two polyoxygenated fatty acids with antifungal activity have been isolated from aerial parts ofAeollanthus parvifolius (Labiatae) using bioassay-guided isolation procedures. Spectroscopic analysis was used to identify the compounds as (Z)-4,9-diacetoxy-6,7-epoxy-5-hydroxy-8-oxododeca-2-enoic acid and (Z)-4,6,7,9-tetraacetoxy-5-hydroxy-8-oxododeca-2-enoic acid. Both of these compounds inhibited spore germination ofCladosporium cucumerinum. Minimum inhibitory doses were 1 µg and 5 µg, respectively, but only the former inhibited germination ofAspergillus niger at a dose of 5 µg. Neither compound exhibited antibacterial activity. (Z)-4,9-Diacetoxy-6,7-epoxy-5-hydroxy-8-oxododeca-2-enoic acid reduced the hyphal growth ofPythium ultimum. The mode of action was not resolved but did not involve either the disruption of the cell wall membrane or the inhibition of extracellular enzymes. Application of (Z)-4,6,7,9-tetraacetoxy-5-hydroxy-8-oxododeca-2-enoic acid to seedling plants did not give any protection against fungal attack, and indeed the compound appeared to be phytotoxic.     

Recovery and recrystallization of electrodeposited bright copper coatings at room temperature. II. X-ray investigation of primary recrystallization

X-ray investigations of the recrystallization processes occurring at room temperature in electrodeposited bright copper coatings were carried outin situ. As a result of the orientation transformation of the growth texture with 311, 111 and 110 components, a recrystallization texture with 100, 110 and 111 components was obtained. It was established that one of the factors which influence the microhardness of copper coatings is the orientation distribution of crystallites.     

Studies on electrical conductivity of gamma irradiated polyaniline

Summary de electrical conductivity at surface of -irradiated polyaniline (PAn) has been studied. EPR spectroscopic results indicate that the variation of spin concentration is consistent with the increase of _de. Electrical conductivity (_de) versus temperature (T) characteristics of unirradiated and irradiated PAn were performed, which demonstrate that the unirradiated curve can fit to ln_deT₁, while the irradiated curve fit to ln_deT_1/4.     

Nucleation and growth kinetics of Ag7NO11 on a platinum single crystal electrode

The process of electrochemical deposition of Ag₇NO₁₁ on a platinum single crystal anode from 5M AgNO₃ is investigated. The nucleation and growth rates are measured at different constant overpotentials. The orientation of the Ag₇NO₁₁ crystals with respect to the substrate surface is determined in the case of deposition on glassy carbon and on the 100, 111 and 110 faces of a platinum single crystal.     

Syntheses and Properties of Aromatic Polyimides Based on 1,1-Bis[4-(4-aminophenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane and 1,1-Bis[4-(4-aminophenoxy)phenyl]-1-phenylethane

A series of fluorinated polyimides were prepared from 1,1-bis[4-(4-aminophenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane with various aromatic tetracarboxylic dianhydrides via a conventional two-step procedure. These polyimides were amorphous in nature and afforded flexible and tough films. Some polyimides derived from less stiff dianhydrides were soluble in polar organic solvents. The glass-transition temperatures (T _g) of these polyimides ranged from 252 to 324C, and softening temperatures (T _s) stayed in the 254322C range. Decomposition temperatures (T _d) at 10% weight loss all occurred above 569C in both air and nitrogen atmospheres. For a comparative study, another series of analogous polyimides based on 1,1-bis[4-(4-aminophenoxy)phenyl]-1-phenylethane were also pepared and characterized.     

Explosive Synthesis of Ultradisperse Aluminum Oxide in an Oxygen‐Containing Medium

Explosive synthesis of ultradisperse aluminum oxide in an oxygencontaining medium is studied. Synthesis conditions that are most optimal for production of the material in the ultradisperse state are determined. A physical model of the process is proposed. It is shown that attenuation of the shock wave causes separation of the shockcompressed material into liquid and solid layers. Possible mechanisms of aluminum combustion with subsequent dispersion of aluminum into the oxygencontaining medium of the explosive chamber are considered. It is shown that ultradisperse aluminum oxide powder is produced mainly from the second layer of the shockcompressed material. Experimental dependences of the yield of the disperse fraction on synthesis conditions are explained using the model proposed.     

New polymer syntheses

Summary Various poly(ether sulfide)s were prepared by polycon-densation of 4-mercaptophenol or silylated 4-mercaptophenol with 2,6-dichloropyridine or 3,6-dichloropyridazine. A two step and an one-pot procedure were compared. The poly-(ether-sulfide)s were characterized by elemental analyses, inherent viscosities, ¹³C-NMR spectroscopy, gel-permeation chromatography and DSC-measurements.     

The effect of cobalt on the reactants adsorption and activity of fused iron catalyst for ammonia synthesis

Modern adsorption study facilities as well as scanning electron microscopy, X-ray diffraction, Mössbauer spectroscopy and X-ray fluorescence spectroscopy were used to investigate the effect of cobalt on the adsorption of nitrogen, hydrogen and ammonia on the surface of cobalt modified iron fused catalysts. Adsorption studies were carried out at the temperature range specific for ammonia synthesis (385C). Activity tests were carried out under 10 MPa in the 350–450 C temperature range. Investigations were performed on the traditional multipromoted iron catalyst and on the series of catalysts prepared with addition of cobalt. Introduction of cobalt changed considerably the sample behaviour during activation and ammonia synthesis. Addition of cobalt promoted the iron catalyst for ammonia synthesis. The most active sample was that containing approximately 5.5 wt% Co. Cobalt changed the adsorption behaviour of the catalyst. Chemisorption of nitrogen is much higher for cobalt catalysts. Growth of nitrogen chemisorption and decrease of ammonia adsorption resulted in the growth of catalytic activity of cobalt catalysts in ammonia synthesis.     

Convective Regime of Filtration Combustion of Energetic Materials in a Cocurrent Flow of Their Combustion Products

The convective regime of filtration combustion of energetic materials in a cocurrent flow of their combustion products is studied using a model with extremely simplified kinetics and heat transfer, which shows instability of the process. It is shown that the more accurate twotemperature model describes a steadystate regime. In this regime, the gas temperature on the hot boundary of the heating zone is well below the combustion temperature, and the solidphase temperature is well below the temperature proposed in recent studies on this topic. It is pointed out that the twotemperature approach is unjustified and intragranular nonisothermicity must be taken into account for convective regimes. It is shown that the threetemperature model, which takes into account this effect, does not give a stable steadystate solution.     

A study of the acidic and catalytic properties of pure and sulfated zirconia–titania and zirconia–silica mixed oxides

Protonated pyridine (PyH⁺) was not found on ZrO₂ (Z) or ZrO₂–TiO₂ (ZT), but was detected on sulfated oxides (ZS, ZTS) by IR spectroscopy. In contrast, ZrO₂–SiO₂ samples containing about 30–80 mol% ZrO₂ showed Brønsted acidity both in nonsulfated (ZS) and sulfated (ZSS) forms. The total acidity was determined by NH₃TPD. Introduction of sulfate ions increased the sitespecific catalytic activity (TOF) in the conversion of cyclopropane or nhexane. The effect of sulfate ions was more significant on samples rich in zirconia. Results suggest that Zr is homogeneously distributed in ZS samples rich in silica. Zirconiabound dimeric sulfate, generating strong acidity, could not be formed in these preparations due to the absence of fairly large ZrO₂ domains.     

Quasi‐Homogeneous and Pseudospin Modes of Zirconium‐Wire Combustion in Air

A novel experimental technique is proposed for examining the transition mechanism from quasihomogeneous to heterogeneous combustion — burning of a variablepitch spring. Depending on the pitch of aircombustible zirconium springs, two combustion modes are possible. Quasihomogeneous (layerbylayer) combustion is observed in the case of smallpitch springs; as the spring pitch increases, quasihomogeneous combustion transforms into heterogeneous (pseudospin) combustion. Conditions for the occurrence of various combustion modes, depending on the spring diameter and pitch, are studied.     

The supracaudal scent gland of the red foxVulpes vulpes

The supracaudal gland of the red fox consists of both tubular apocrine sweat glands and massively developed sebaceous glands. The gland is characterized by a high level of histochemically demonstrable hydroxysteroid dehydrogenase activity (particularly -3 HSD) and by the presence of naturally fluorescent photolabile sebum constituents. Evidence suggests that these components may be carotenoid. Results are presented in the context of histological observations and are discussed in relation to scent production.     

Critical solution point and chain dimension of branched-polystyrene solutions

Summary Critical solution point and chain dimension were measured for branched polystyrene(BPS) in solution as a function of molecular weight(M) and compared with those for linear polystyrene(LPS). The critical concentration _c of BPS was quite different from that of LPS at a fixed M, but the same at a fixed overlap-concentration ^*, i.e., plots of _c vs. ^* fall on a single straight line for both BPS and LPS (gf_c ^*). Reduced critical temperature _c defined by gt_c=(–T_c)/ [T_c: critical temperature, : the -temperature] was related to _c as _{c c} ² for BPS, whereas _{c c} for LPS.     

Variable‐temperature IR spectroscopic studies of CO adsorbed on Na‐ZSM‐5 and Na‐Y zeolites

CO interacts with extraframework alkali metal cations (M⁺=) of zeolites to form both M⁺CO and M⁺OC species. By using variabletemperature FTIR spectroscopy, these Cbonded and Obonded species were found to be in a temperaturedependent equilibrium. For the same cation, the difference in interaction energy depends upon the zeolite framework. Thus, for the equilibrium process ZNa⁺=CO ZNa⁺OC, where Z represents the zeolite framework, H ⁰ was found to take the values 3.8 and 2.4 kJ mol^– for CO/NaZSM5 and CO/NaY, respectively. The Cbonded species show always the highest cation–CO interaction energy.     

Identification of sex pheromones of two sibling species in dingy cutworm complex,Feltia jaculifera (GN.) (Lepidoptera: Noctuidae)

The sex pheromone components of the two sibling species of the dingy cutworm that occur on the prairies of western Canada were identified in abdomen-tip extracts from calling female moths. Three monounsaturated acetates, (Z)-7-dodecenyl acetate, (Z)-9-tetradecenyl acetate, and (Z)-11-hexadecenyl acetate, are common to both species in ratios of 100133 for species A and 0.30.5100 for species B. The most effective synthetic blends for the attraction of male moths in the field consisted of these three components in ratios of 1010 at 8.8g/lure for species A and 112000 at 500g/lure for species B. The addition of Z5-12Ac to either blend reduced the catches and the addition of Z7-12OH orZ11-16OH to the three-component blend reduced the catches of species B males. The species are morphologically indistinguishable, but the identity of the males attracted to the synthetic blends could be confirmed by their antennal responses to a test blend of the three components using a GC-EAD system. Both synthetic attractant blends are competitive with females and will be useful for studying the distribution, biology, and relative abundances of the two species.Contribution no. 3879005 of the Lethbridge Research Station.     

Calculation of the Viscosity of Glass-Forming Melts: VI. The R2O–B2O3–SiO2and RO–B2O3–SiO2Ternary Borosilicate Systems

A method for calculating the viscosity from composition and temperature for melts in the R _m O _n –B₂O₃–SiO₂systems is proposed. The change in the concentrations of structural groups depending on the melt composition is taken into account in calculations. The results of calculations are compared with the experimental data available in the literature on the viscosity of 1200 melts with the use of the SciGlass information system. The root-mean-square deviation between the experimental and calculated characteristic temperatures varies from 30 K (for the glass transition temperature and the Littleton point) to 50 K (for a viscosity of 10⁴P).     

Postinduction Processes During Thermal Explosion in the Systems “Porous Material–Reactive Gas–Solid Product”

A complete solution of the unsteadystate filtration problem of thermal explosion incorporating the postinduction period is given for the first time. The paper describes a study of the temperaturefield dynamics, poregas pressure, and the degree of condensedphase conversion versus the reactivegas deficiency in a reactive porous material. Focus is on the formation and propagation of frontal regimes of exothermic chemical reactions (their number, direction, and velocity of propagation, degree of condensedphase conversion at the front). The study revealed double selfignition phenomena and combustionwave propagation regimes with incomplete conversion at the front. A surface regime of thermal explosion limited by gas filtration from the outside was considered. The regularities in the dynamics of the exothermic chemical reaction found in the present study allow one to qualitatively control hightemperature synthesis under thermal explosion conditions.