功能梯度三相复合材料圆柱壳的非线性振动研究

论文研究了一种由环氧树脂、石墨烯纳米片、碳纤维制成的功能梯度三相复合材料圆柱壳的非线性振动响应.基于一阶剪切变形理论和von-Karman几何非线性关系,考虑到温湿效应、气动力和外激励的共同作用,利用Hamilton原理建立了两端固支圆柱壳的非线性偏微分运动方程.利用Galerkin法将非线性偏微分运动方程离散成一组相互耦合的二阶非线性常微分方程,利用伪弧长延拓法求解非线性常微分方程组,给出对应的幅频响应曲线.本论文中仅考虑湿度和外激励等参数的变化对新型三相复合材料圆柱壳结构非线性振动响应的影响,分析了湿度和外激励的变化对功能梯度三相复合材料圆柱壳共振响应的影响.     

功能梯度薄壁圆柱壳的自由振动

研究了由功能梯度材料制成的薄壁圆柱壳的自由振动.采用幂律分布规律描述功能梯度材料沿厚度的梯度性质,根据Donnell壳体理论,导出了功能梯度材料薄壁圆柱壳线性振动的简化控制方程.基于此理论分析了功能梯度圆柱壳的自由振动特性,给出了两端简支功能梯度材料薄壁圆柱壳小挠度固有振动的频率公式.以简支圆柱壳作为算例,与前人结果及有限元法对比验证了该简化功能梯度薄壁圆柱壳理论的正确性,同时讨论了周向波数及梯度指数对其频率的影响.     

带裂纹石墨烯增强金属泡沫梁的振动特性研究

分析了带裂纹功能梯度石墨烯增强金属泡沫梁的自由振动.采用Timoshenko梁理论进行建模,裂纹由无质量扭转弹簧模拟,利用Halpin Tsai微观力学模型预测材料的有效性能.通过哈密顿原理,得到了带裂纹功能梯度石墨烯增强金属泡沫(FG GPLRMF)梁的运动方程及其边界条件.采用微分变换法分析带裂纹FG GPLRMF梁的自由振动.结果表明,带裂纹FG GPLRMF梁的振动特性受到石墨烯几何尺寸、孔隙类型和石墨烯分布的影响显著.     

压电纤维复合材料层合壳的非线性动力学研究

本文对横向激励作用下的1-3型压电纤维复合材料层合壳进行了非线性动力学分析,并研究了压电特性对结构振动响应的影响.首先建立了压电纤维复合材料层合壳的非线性动力学方程,并且在已知的几何结构和材料特性基础上考虑了电场属性.然后根据位移边界条件,选择合适的振型函数,通过Galerkin方法将运动控制方程转化成两自由度的非线性常微分方程.通过数值模拟方法分析了横向激励和压电系数对压电纤维复合材料层合壳非线性振动特性的影响.通过波形图、三维相图、庞加莱图和分叉图等来研究壳体不同类型的周期和混沌运动.结果表明,外激励作用下结构存在复杂的非线性振动响应,同时压电参数对层合壳结构振动响应具有很强的调节作用.     

石墨烯树脂复合材料板1∶3内共振非线性动力学分析

石墨烯是一种新型的碳纳米材料,将石墨烯添加到不同基体中可达到增强基体力学性能,并优化结构的效果.本文主要研究了在悬臂边界条件下石墨烯复合材料板的非线性动力学行为,通过Halpin-Tsai模型计算了复合材料板的等效杨氏模量,运用一阶剪切板理论和Hamilton原理得到复合材料板的非线性动力学方程.通过模态缩聚,得到复合材料板横向位移的运动控制方程.应用Rayleigh-Ritz法计算出复合材料板的固有频率,发现第二阶与第四阶固有频率间存在1:3的关系.利用多尺度法研究了复合材料板在1:3内共振情况下的非线性振动响应,通过数值模拟分析了外激励对板结构非线性振动响应的影响.结果表明:横向外激励对复合材料板的非线性动力学行为影响较大,对实际工程具有一定的指导意义.     

对接圆柱壳结构模态特性分析

对接圆柱壳结构在航空航天、船舶、土木和机械等工程领域得到广泛应用,对其模态特性的分析是研究其动力学特性的重要方向.本文简要介绍了模态分析技术和最小二乘复频域法(PolyMAX)的基本原理,并对对接圆柱壳结构进行了计算模态分析和实验模态分析.实验模态分析过程中,针对自由边界的实验实现、分析结果的正确性进行了讨论,并将实验结果与计算模态分析结果进行对比,对比结果表明：对接圆柱壳结构具有圆柱壳结构一般振动特性的同时,由于对接形式的存在出现了以法兰面为分界的非对称振动.     

石墨烯增强复合材料悬臂板的气动颤振分析及振动抑制研究

本文针对石墨烯增强复合材料悬臂板的气动颤振特性及振动控制问题开展了研究.利用Halpin-Tsai及混合率计算了石墨烯增强复合材料的等效材料参数,运用经典板理论、第二类压电方程和Hamilton原理得到了结构的运动控制方程.通过Rayleigh-Ritz法计算了石墨烯增强复合材料悬臂板的固有频率,探究了X-GPLs,U...     

基于有限差分法的端部约束同轴圆柱壳的流致失稳分析

本文基于经典壳体和理想势流理论建立圆柱壳流固耦合系统的运动方程,并引入有限差分法(FDM)对运动方程进行离散.为将壳体表面的扰动压力离散到差分网格节点,基于差分离散的原理,提出了以分段函数作为基函数的展开方法.本文对结构与压力控制方程均采用FDM方法进行求解,发展了一种基于FDM的同轴圆柱壳流固耦合求解策略.首先,利用本文方法计算了同轴圆柱壳在静态流体环境中的振动频率,并与有限元软件(ANSYS)的计算结果相比较,验证了本文方法的正确性；然后,探究了在静流体环境中同轴圆柱壳的结构参数变化对其振动频率的影响规律；最后,研究了同轴圆柱壳系统在运动流体环境中的流弹失稳问题.     

周期载荷下电活性聚合物圆柱壳的动力响应

基于非线性动力学理论研究了不可压电活性聚合物圆柱壳在内表面周期载荷作用下的运动与破坏等动力响应问题.通过对所得描述圆柱壳内表面运动的非线性常微分方程的数值计算和动力学定性分析,发现存在临界载荷和临界电压;当周期载荷的平均载荷值小于临界载荷及外加电压小于临界电压时,圆柱壳的运动随时间的演化是拟周期性的非线性振动.反之,圆柱壳将被破坏.讨论了外加电场和载荷参数对临界值和圆柱壳运动特性的影响.     

圆柱壳在水下爆炸载荷作用下的动力仿真分析

圆柱壳是船舶、潜艇和海洋工程结构物的重要组成部分,研究其在水下爆炸载荷作用下的响应对提高结构物的使用周期有着重要的作用.利用LS-DYNA动力有限元程序对张效慈等人做的深水爆炸水动压力场对潜体结构的动态响应试验进行数值模拟.分析了不同材料圆柱壳和不同参数复合材料圆柱壳在水下爆炸载荷作用下的抗冲击性.计算结果表明,复合材料比钢、铜、铝合金金属材料的抗冲击性好,弹性模量小的复合材料的抗冲击性好.方法可以简单快速的计算圆柱壳的抗冲击性,为舰船的设计提供参考.     

Only connect: teaching, technology and telesis

Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained.     

European Community policy and the market

Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven.     

一种自适应子融合集成多分类器方法

融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。     

Avoiding semantic and temporal gaps in developing software intensive systems

Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them.     

Designing economic np control charts: A programmed simulation approach

This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives.     

The development of robot art

Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Explanation and prediction: an architecture for default and abductive reasoning

Although there are many arguments that logic is an appropriate tool for artificial intelligence, there has been a perceived problem with the monotonicity of classical logic. This paper elaborates on the idea that reasoning should be viewed as theory formation where logic tells us the consequences of our assumptions. The two activities of predicting what is expected to be true and explaining observations are considered in a simple theory formation framework. Properties of each activity are discussed, along with a number of proposals as to what should be predicted or accepted as reasonable explanations. An architecture is proposed to combine explanation and prediction into one coherent framework. Algorithms used to implement the system as well as examples from a running implementation are given.     

Three Process Perspectives: Organizations, Teams, and People

This paper provides the author's personal views and perspectives on software process improvement. Starting with his first work on technology assessment in IBM over 20 years ago, Watts Humphrey describes the process improvement work he has been directly involved in. This includes the development of the early process assessment methods, the original design of the CMM, and the introduction of the Personal Software Process (PSP)^SM and Team Software Process (TSP){^SM}. In addition to describing the original motivation for this work, the author also reviews many of the problems he and his associates encountered and why they solved them the way they did. He also comments on the outstanding issues and likely directions for future work. Finally, this work has built on the experiences and contributions of many people. Mr. Humphrey only describes work that he was personally involved in and he names many of the key contributors. However, so many people have been involved in this work that a full list of the important participants would be impractical.     

基于复小波噪声方差显著修正的SAR图像去噪

提出了一种基于复小波域统计建模与噪声方差估计显著性修正相结合的合成孔径雷达(Synthetic Aperture Radar,SAR)图像斑点噪声滤波方法。该方法首先通过对数变换将乘性噪声模型转化为加性噪声模型,然后对变换后的图像进行双树复小波变换(Dualtree Complex Wavelet Transform,DCWT),并对复数小波系数的统计分布进行建模。在此先验分布的基础上,通过运用贝叶斯估计方法从含噪系数中恢复原始系数,达到滤除噪声的目的。实验结果表明该方法在去除噪声的同时保留了图像的细节信息,取得了很好的降噪效果。     

基于QTE的蒙古文显示机制研究与实现

蒙古语言是中国蒙古族使用的通用语言,由于蒙古文区别于其他文字的书写方式和其自身变形机制等特点,在很多通用的文字处理引擎中都不被支持。在嵌入式产品开发与应用领域中Linux加QTE已经成为流行方式。该文给出了一种在QTE环境上实现基于标准Unicode的蒙古文点阵显示和变形算法, 并自定义了支持蒙古文的QTE组件,扩展了QTE功能,为在Linux加QTE方式的嵌入式体系结构中处理蒙古文提供了一种解决方法。