应用于IEEE 802.11b无线局域网系统的2.4GHzCMOS单片收发机射频前端

实现了一个应用于IEEE 802.11b无线局域网系统的2.4GHz CMOS单片收发机射频前端,它的接收机和发射机都采用了性能优良的超外差结构.该射频前端由五个模块组成:低噪声放大器、下变频器、上变频器、末前级和LO缓冲器.除了下变频器的输出采用了开漏级输出外,各模块的输入、输出端都在片匹配到50Ω.该射频前端已经采用0.18μm CMOS工艺实现.当低噪声放大器和下变频器直接级联时,测量到的噪声系数约为5.2dB,功率增益为12.5dB,输入1dB压缩点约为-18dBm,输入三阶交调点约为-7dBm.当上变频器和末前级直接级联时,测量到的噪声系数约为12.4dB,功率增益约为23.8dB,输出1dB压缩点约为1.5dBm,输出三阶交调点约为16dBm.接收机射频前端和发射机射频前端都采用1.8V电源,消耗的电流分别为13.6和27.6mA.     

A 900-MHz dual-conversion low-IF GSM receiver in 0.35-μm CMOS

A low-power fully integrated GSM receiver is developed in 0.35-μm CMOS. This receiver uses dual conversion with a low IF of 140 kHz. This arrangement lessens the impact of the flicker noise. The first IF of 190 MHz best tolerates blocking signals. The receiver includes all of the circuits for analog channel selection, image rejection, and more than 100-dB controllable gain. The receiver alone consumes 22 mA from a 2.5-V supply, to give a noise figure of 5 dB, and input IP3 of -16 dBm. A single frequency synthesizer generates both LO frequencies. The integrated VCO with on-chip resonator and buffers consume another 8 mA, and meets GSM phase-noise specifications     

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver is presented. The problems to implement the low voltage design and the on-chip input/output impedance matching are considered, and some improved circuits are presented to overcome the problems. Especially, a single-end input, differential output double balanced mixer with an on-chip bias loop is analyzed in detail to show its advantages over other mixers. The transceiver RF front-end has been implemented in 0.18 um CMOS process, the measured results show that the Rx front-end achieves 5.23 dB noise figure, 12.7 dB power gain (50 ohm load), −18 dBm input 1 dB compression point (ICP) and −7 dBm IIP3, and the Tx front-end could output +2.1 dBm power into 50 ohm load with 23.8 dB power gain. The transceiver RF front-end draws 13.6 mA current from a supply voltage of 1.8 V in receive mode and 27.6 mA current in transmit mode. The transceiver RF front-end could satisfy the performance requirements of IEEE802.11b WLAN standard. Supported by the National Natural Science Foundation of China, No. 90407006 and No. 60475018.     

A 2.4-GHz CMOS transceiver for Bluetooth

A fully integrated CMOS transceiver tuned to 2.4 GHz consumes 46 mA in receive mode and 47 mA in transmit mode from a 2.7-V supply. It includes all the receive and transmit building blocks, such as frequency synthesizer, voltage-controlled oscillator (VCO), power amplifier, and demodulator. The receiver uses a low-IF architecture for higher level of integration and lower power consumption. It achieves a sensitivity of -82 dBm at 0.1% BER, and a third-order input intercept point (IIP3) of -7 dBm. The direct-conversion transmitter delivers a GFSK modulated spectrum at a nominal output power of 4 dBm. The on-chip voltage controlled oscillator has a close-in phase-noise of -120 dBc/Hz at 3-MHz offset     

A Low-Power Fullband 802.11a/b/g WLAN Transceiver With On-Chip PA

A low-power fullband 802.11a/b/g WLAN transceiver in 0.15-mum CMOS technology is described. The zero-IF transceiver achieves a receiver noise figure of 4.4/4 dB for the 2.4-GHz/5-GHz bands, respectively. The corresponding sensitivity at 54-Mb/s operation is -72 dBm for 802.11g and -74 dBm for 802.11a using actual PER measurement. An on-chip PA delivers 20 dBm output P1-dB. A new I/Q compensation scheme is implemented in local oscillator (LO) and an image rejection of better than 52 dB is observed. The transmitter delivers 10/1.5 dBm (2.4-/5-GHz) EVM-compliant output power for a 64-QAM OFDM signal at 54-Mb/s. The power consumption is 117/135 mW (1.8-V) in the receive mode and 570/233.1 mW in the transmit mode for 2.4/5 GHz, respectively. The low power consumption, high integration and robustness (-40 to 140degC) make this transceiver suitable for portable applications     

A Design of WCDMA RF Transceiver with Its Performance Measuring

A 2-GHz radio frequency transceiver is presented and implemented for third generation mobile communications using wide-band code division multiple access （WCDMA） scheme. Performance measuring systems are introduced for transmitter channel and receiver sensitivity, respectively. The transceiver achieves maximum output power of 22 dBm, dynamic range of 85 dB, adjacent channel power rejection ratio （ACPR） of -41dB@5MHz, and receiver sensitivity of-119.6 dBm for 128-kb/s data at 3.84-Mcps spreading rate. The measured results indicate the conformity to the required commercial 2.0-GHz WCDMA specification and 3GPP requirements.     

A 2.7-V 1.8-GHz fourth-order tunable LC bandpass filter based on emulation of magnetically coupled resonators

A low-voltage fourth-order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled inductors, thus providing bandwidth tuning with small passband ripple. Each resonator is built using on-chip spiral inductors and accumulation-mode pMOS capacitors to provide center frequency tuning. The filter has been implemented in HP 0.5-/spl mu/m CMOS process and occupies an area of 0.15 mm/sup 2/. It consumes 16 mA from a single 2.7-V supply at a center frequency of 1.84 GHz and a bandwidth of 80 MHz while providing a passband gain of 9 dB and more than 30 dB of image attenuation for an IF frequency of 100 MHz. The measured output 1-dB compression point and output noise power spectral densities are -16 dBm and -137 dBm/Hz, respectively. This results in a 1-dB compression dynamic range of 42 dB. The filter minimum power supply voltage for proper operation is 2 V. The chip experimental results are in good agreement with theoretical results.     

5-GHz CMOS radio transceiver front-end chipset

Incorporating the direct-conversion architecture, a 5-GHz band radio transceiver front end chipset for wireless LAN applications is implemented in a 0.25-μm CMOS technology. The 4-mm² 5.25-GHz receiver IC contains a low noise amplifier with 2.5-dB noise figure (NF) and 16-dB power gain, a receive mixer with 12.0 dB single sideband NF, 13.7-dB voltage gain, and -5 dBm input 1-dB compression point. The 2.7-mm² transmitter IC achieves an output 1-dB compression of -2.5 dBm at 5.7 GHz with 33.4-dB (image) sideband rejection by using an integrated quadrature voltage-controlled oscillator. Operating from a 3-V supply, the power consumptions for the receiver and transmitter are 114 and 120 mW, respectively     

A low-power 2.4-GHz transmitter/receiver CMOS IC

A 2.4-GHz CMOS receiver/transmitter incorporates circuit stacking and noninvasive baseband filtering to achieve a high sensitivity with low power dissipation. Using a single 1.6-GHz local oscillator, the transceiver employs two upconversion and downconversion stages while providing on-chip image rejection filtering. Realized in a 0.25-/spl mu/m digital CMOS technology, the receiver exhibits a noise figure of 6 dB and consumes 17.5 mW from a 2.5-V supply, and the transmitter delivers an output power of 0 dBm with a power consumption of 16 mW.     

一种用于900MHz射频识别(RFID)读写器芯片的1.8VCMOS直接变频接收机

设计了针对解决900MHz RFID读写器收发机芯片中本地载波干扰问题而优化的直接变频接收机,并在0.18μm 1P6M混合信号CMOS工艺上实现验证.设计中使用了一种串联反馈结构的基带放大器以达到同时实现无源混频器输出缓冲,直流消除以及信号放大的功能.实际测量显示,该接收机的输入1dB压缩点为-4dBm,当中频信号解调信噪比要求为10dB时,可达到的灵敏度为-70dBm.该接收机与整个收发机集成在同一块芯片中,使用1.8V电源电压,工作时静态电流为90mA.     

A 2.4-GHz Low-Power Low-IF Receiver and Direct-Conversion Transmitter in 0.18-μm CMOS for IEEE 802.15.4 WPAN Applications

In this paper, a low-power low-IF receiver and a direct-conversion transmitter (DCT) suitable for the IEEE standard 802.15.4 radio system at the 2.4-GHz band are presented in 0.18-mum deep n-well CMOS technology. By using vertical NPN (V-NPN) bipolar junction transistors in the baseband analog circuits of the low-IF receiver, the image rejection performance is improved and the power consumption is reduced. In addition, by applying the V-NPN current mirrored technique in a DCT, the carrier leakage is reduced and the linearity performance is improved. The receiver has 10 dB of noise figure, -15 dBm of third-order input intercept point, and 35 dBc of image rejection. The transmitter has more than -2 dBm of transmit output power, -35 dBc of local oscillator leakage, and -46 dBc of the transmit third harmonic component. The receiver and transmitter dissipate 6 and 9 mA from a 1.8-V supply, respectively     

适于视频应用的高数据传输率集成CMOS收发机

这篇文章给出了一个5GHz CMOS射频收发机的设计方案。此设计采用0.18微米射频CMOS加工工艺,集合了最新IEEE802.11n的特性例如多输入多输出技术的专利协议以及其他无线技术,可提供应用在家庭环境中的实时高清电视数据的无线高速传输。设计频率涵盖了从4.9GHz到5.9GHz的ISM频带,每个射频信道的频宽为20MHz。收发机采用了直接上变频发射器和低中频接收器的结构。在没有片上校准的情况下,设计采用双正交直接上变频混频器,得到了超过35dB的镜像抑制。测试结果得到6dB接收机噪声系数以及在-3dBm输出功率时得到发射机EVM结果优于33dB。     

A 0.13 $mu$ m CMOS Quad-Band GSM/GPRS/EDGE RF Transceiver Using a Low-Noise Fractional-N Frequency Synthesizer and Direct-Conversion Architecture

This paper presents a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS/EDGE applications which adopts a direct-conversion receiver, a direct-conversion transmitter and a fractional-N frequency synthesizer with a built-in DCXO. In the GSM mode, the transmitter delivers 4 dBm of output power with 1$^{circ}$ RMS phase error and the measured phase noise is ${-}$164.5 dBc/Hz at 20 MHz offset from a 914.8$~$MHz carrier. In the EDGE mode, the TX RMS EVM is 2.4% with a 0.5 $~$dB gain step for the overall 36 dB dynamic range. The RX NF and IIP3 are 2.7 dB/ ${-}$12 dBm for the low bands (850/900 MHz) and 3 dB/${-}$ 11 dBm for the high bands (1800/1900 MHz). This transceiver is implemented in 0.13 $mu$m CMOS technology and occupies 10.5 mm$^{2}$ . The device consumes 118 mA and 84 mA in TX and RX modes from 2.8 V, respectively and is housed in a 5$,times,$ 5 mm$^{2}$ 40-pin QFN package.      

Ka波段一体化收发信机设计

Ka波段一体化收发信机是无线通信系统中的重要电路,它对整个系统的噪声系数,灵敏度等关键指标起决定性作用。文中对Ka波段一体化收发信机的工作原理进行了阐述,同时给出了整机功能实现框图,分析了接收通道单元、本振单元、发射通道单元和电源控制单元共4个单元的设计方案,并给出了仿真结果与测试结果。试验结果表明,Ka波段一体化收发信机接收机噪声系数≤2.2 dB、增益≥60 dB、输入输出驻波、相位噪声杂散、镜像抑制等指标均满足技术要求。发射机1 dB压缩点功率≥30 dBm,增益≥50 dB,三阶交调,杂波抑制等均满足实用技术要求,并根据测试结果对Ka波段一体化收发信机的部分技术指标提出了进一步优化的方案。     

用于434/868MHz FSK/OOK CMOS发射机的锁相环设计

一种可输出434/868MHz信号的Σ-Δ分数分频锁相环在0.35μmCMOS工艺中集成。该发射机系统采用直接调制锁相环分频比的方式实现FSK调制,OOK的调制则通过功率预放大器的开-关实现。为了降低芯片的成本和功耗,发射机采用了电流数字可控的压控振荡器(VCO),以及片上双端-单端转换电路,并对分频器的功耗设计进行研究。经测试表明,锁相环在868MHz载波频偏为10kHz、100kHz和3MHz处的相位噪声分别为-75dBc/Hz、-104dBc/Hz和-131dBc/Hz,其中的VCO在100kHz频偏处的相位噪声为-108dBc/Hz。在发送模式时,100kHz相邻信道上的功率与载波功率之比小于-50dB。在直流电压2.5V的工作条件下,锁相环的电流为12.5mA,包括功率预放大器和锁相环在内的发送机总面积为2mm2。     

A 2.5-GHz BiCMOS transceiver for wireless LAN's

A BiCMOS transceiver intended for spread spectrum applications in the 2.4-2.5 GHz band is described. The IC contains a low-noise amplifier (LNA) with 14 dB gain and 2.2 dB NF in its high-gain mode, a downconversion mixer with 8 dB gain and 11 dB NF, and an upconversion mixer with 17 dB gain and P_{-1 dB} of +3 dBm out. An on-chip local oscillator (LO) buffer accepts LO drive of -10 dBm with a half-frequency option allowed by an on-chip frequency doubler. Power consumption from a single 3-V supply is 34 mA in transmit mode, 21 mA in receive mode, and 1 μA in sleep mode     

A low-current and low-distortion wideband amplifier using 0.2-μmgate MODFET fabricated by using phase-shift lithography

We have developed a wide-band amplifier that can keep a gain over 10 dB at an operation current of 10 mA from 100 MHz to 3 GHz. The fabricated integrated circuit (IC) achieved a high-output third-order intercept point of 30 dBm and low noise figure of 1.6 dB at 800 MHz, respectively. The present IC employs a MODFET with 0.2-μm gate fabricated by using a phase-shift lithography technique     

A monolithic 3.1-4.8 GHz MB-OFDM UWB transceiver in 0.18-μm CMOS

A monolithic RF transceiver for an MB-OFDM UWB system in 3.1-4.8 GHz is presented.The transceiver adopts direct-conversion architecture and integrates all building blocks including a gain controllable wideband LNA,a I/Q merged quadrature mixer,a fifth-order Gm-C bi-quad Chebyshev LPF/VGA,a fast-settling frequency synthesizer with a poly-phase filter,a linear broadband up-conversion quadrature modulator,an active D2S converter and a variablegain power amplifier.The ESD protected transceiver is fabricated in Jazz Semiconductor's 0.18-μm RF CMOS with an area of 6.1 mm2 and draws a total current of 221 mA from 1.8-V supply.The receiver achieves a maximum voltage gain of 68 dB with a control range of 42 dB in 6 dB/Step,noise figures of 5.5-8.8 dB for three sub-bands,and an inband/out-band IIP3 better than-4 dBm/+9 dBm.The transmitter achieves an output power ranging from-10.7 to-3dBm with gain control,an output P1dB better than-7.7 dBm,a sideband rejection about 32.4 dBc,and LO suppression of 31.1 dBc.The hopping time among sub-bands is less than 2.05 ns.     

17 GHz RF Front-Ends for Low-Power Wireless Sensor Networks

A 17 GHz low-power radio transceiver front-end implemented in a 0.25 $mu{hbox {m}}$ SiGe:C BiCMOS technology is described. Operating at data rates up to 10 Mbit/s with a reduced transceiver turn-on time of 2 $mu{hbox {s}}$, gives an overall energy consumption of 1.75 nJ/bit for the receiver and 1.6 nJ/bit for the transmitter. The measured conversion gain of the receiver chain is 25–30 dB into a 50 $Omega$ load at 10 MHz IF, and noise figure is 12 $pm$0.5 dB across the band from 10 to 200 MHz. The 1-dB compression point at the receiver input is $-$37 dBm and ${hbox{IIP}}_{3}$ is $-$25 dBm. The maximum saturated output power from the on-chip transmit amplifier is $-$1.4 dBm. Power consumption is 17.5 mW in receiver mode, and 16 mW in transmit mode, both operating from a 2.5 V supply. In standby, the transceiver supply current is less than 1 $mu{hbox {A}}$.      

A 5-GHz highly integrated receiver front-end

In this paper a radio front-end for a IEEE 802.11a and HIPERLAN2 sliding-IF receiver is presented. The circuit, implemented in a low-cost 46-GHz-f _T silicon bipolar process, includes a variable-gain low noise amplifier and a double-balanced mixer. Thanks to monolithic LC filters and on-chip single-ended-to-differential conversion of the RF signal, the proposed solution does not require the expensive image rejection filter and an external input balun. The receiver front-end exhibits a 4.3-dB noise figure and a power gain of 21 dB, providing an image rejection ratio higher than 50 dB. By using a 1-bit gain control, it achieves an input 1-dB compression point of −11 dBm, while drawing only 22 mA from a 3-V supply voltage.