Electrical properties of Pb(Mg1/3Nb2/3)O3-PbTiO3 ceramics modified with WO3

Ferroelectrics 0.67Pb (Mg_1/3Nb_2/3)O₃-0.33PbTiO₃ (PMN-PT) + x mol% WO₃ (x=0.1, 0.5, 1, 2) were prepared by columbite precursor method. Electrical properties of WO₃-modified ferroelectrics were investigated. X-ray diffraction (XRD) was used to identify crystal structure, and pyrochlore phase were observed in 0.67Pb (Mg_1/3Nb_2/3)O₃-0.33PbTiO₃+2 mol% WO₃. Dielectric peak temperature decreased with WO₃ doping, indicating that W⁶⁺ incorporated into PMN-PT lattice. Lattice constant, pyrochlore phase and grain size contribute to the variation of K_max. Both piezoelectric constant (d₃₃) and electromechanical coupling factors (k_p) were enhanced by doping 0.1 mol% WO₃, which results from the introduction of “soft” characteristics into PMN-PT, while further WO₃ addition was detrimental. We consider that the two factors, introduction of “soft” characteristics and the formation of pyrochlore phase, appear to act together to cause the variation of piezoelectric properties of 0.67PMN-0.33PT ceramics doping with WO₃.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Effects of CuO doping on the electrical properties of 0.98K0.5Na0.5NbO3-0.02BiScO3 lead-free piezoelectric ceramics

CuO-doped 0.98K_0.5Na_0.5NbO₃-0.02BiScO₃ (0.98KNN-0.02BS-xCu) lead-free piezoelectric ceramics have been fabricated by ordinary sintering technique. The effects of CuO doping on the dielectric, piezoelectric, and ferroelectric properties of the ceramics were mainly investigated. X-ray diffraction reveals that the samples at doping levels of x ≤ 0.01 possess a pure tetragonal perovskite structure. The specimen doped with 1 mol% CuO exhibits enhanced electrical properties (d₃₃ ~ 207 pC/N, k_p ~ 0.421, and k_t = 0.424) and relatively high mechanical quality factor (Q_m = 288). These results indicate that the 0.98KNN-0.02BS-0.01Cu ceramic is a promising candidate for lead-free piezoelectric ceramics for applications such as piezoelectric actuators, harmonic oscillator and so on.     

Comparative investigation of structure and dielectric properties of Pb(Mg1/3Nb2/3)O3-PbTiO3 (65/35) and 10% PbZrO3-doped Pb(Mg1/3Nb2/3)O3-PbTiO3 (65/35) ceramics prepared by a modified precursor method

Relaxor ferroelectric Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (65/35) and 10% PbZrO₃-doped Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (65/35) ceramics were both prepared by a modified precursor method, which was based on the high-temperature synthesis of an oxide precursor that contained all the B-site cations for the consideration of B-site homogeneity. The dielectric properties of Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (65/35) ceramic was more of normal ferroelectric behavior, but the high dielectric constant (?_m = 34,200 at 1 kHz) and piezoelectric constant (d₃₃ = 709 pC/N) were observed for this composition close to the morphotropic phase boundary. Comparatively, introduction of 10% PbZrO₃ into Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (65/35) ceramics enhanced the diffuse phase transition as well as the rhombohedral to tetragonal phase transition temperature, while it also kept the high dielectric constant (?_m = 29,600 at 1 kHz) and piezoelectric constant (d₃₃ = 511 pC/N).     

Effects of ZnNb2O6 addition on BaTiO3 ceramics for energy storage

BaTiO₃ ceramics were prepared using solid state reaction with addition of ZnNb₂O₆, to investigate the effects of ZnNb₂O₆ addition on structure and properties. The results show that the ZnNb₂O₆ addition lowers sintering temperature, decreases grain size, while introduces second phase (Ba₂Ti₅O₁₂) for x ≥ 7.26 wt%. The dielectric breakdown strength is enhanced with the increasing doping level of ZnNb₂O₆ and reaches a maximum value at x = 7.26 wt%, exhibiting a maximum energy storage capability.     

Modified (K0.5Na0.5)(Nb0.9Ta0.1)O3 ceramics with high Qm

Lead-free ceramics (K_0.5Na_0.5)(Nb_0.9Ta_0.1)O₃ (KNNT) + x mol% K₄CuNb₈O₂₃ (KCN) + y mol% MnO₂ have been prepared using the conventional solid-state reaction technique. Crystalline structures and Microstructures were analyzed by X-ray diffraction and scanning electron microscope (SEM) at room temperature. The low dielectric loss tanδ and relatively high piezoelectric properties were obtained when KCN and MnO₂ were added into KNNT ceramics. The ceramics with x = 1.0, y = 0.50 exhibited excellent piezoelectric properties: high mechanical quality factor Q_m = 1563, piezoelectric coefficient d₃₃ = 96pC/N, electromechanical coupling coefficient k_p = 42.2%, k_t = 44.5%, k₃₃ = 58.4%, relative dielectric constant ε′ = 308, tanδ = 0.4%. This material is a promising candidate for the lead-free piezoelectric transformer applications.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by Substituting Mg for Co

The microwave dielectric properties of La(Mg_0.5−xCo_xSn_0.5)O₃ ceramics were examined with a view to exploiting them for mobile communication. The La(Mg_0.5−xCo_xSn_0.5)O₃ ceramics were prepared using the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Co_0.1Sn_0.5)O₃ ceramics revealed that La(Mg_0.4Co_0.1Sn_0.5)O₃ is the main crystalline phase, which is accompanied by small extent of La₂Sn₂O₇ as the second phase. Formation of this Sn-rich second phase was attributed to the loss of MgO upon ignition. Increasing the sintering temperatures seemed to promote the formation of La₂Sn₂O₇. An apparent density of 6.67 g cm⁻³, a dielectric constant (?_r) of 20.3, a quality factor (Q.F.) of 70,500 GHz, and a temperature coefficient of resonant frequency (τ_f) of −77 ppm °C⁻¹ were obtained for La(Mg_0.4Co_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Electric-field-induced strain and piezoelectric properties of a high Curie temperature Pb(In1/2Nb1/2)O3-PbTiO3 single crystal

The temperature dependence of dielectric and piezoelectric properties, electric-field-induced strains of 0.66 Pb(In_1/2Nb_1/2)O₃-0.34 PbTiO₃ single crystals, which were grown directly from melt by using the modified Bridgman technique with the allomeric Pb(Mg_2/3Nb_1/3)O₃-PbTiO₃ seed crystals, were determined as a function of crystallographic orientation with respect to the prototypic (cubic) axes. Ultrahigh piezoelectric response (d₃₃∼2000 pC/N, k₃₃∼94%) and strain levels up to 0.8%, comparable to rhombohedral (1−x)Pb(Mg_2/3Nb_1/3)O₃-xPbTiO₃ and (1−x)Pb(Zn_2/3Nb_1/3)O₃-xPbTiO₃ single crystals, were observed for the 〈0 0 1〉-oriented crystals. Strain levels up to 0.47% and piezoelectric constant d₃₃∼1600 pC/N could be achieved being related to an electric-field-induced rhombohedral-orthorhombic phase transition for the 〈1 1 0〉-oriented crystals. In addition, high electromechanical coefficients k₃₃ (∼88%) can be achieved even heating to 110 °C. High T_C (∼200 °C), large electromechanical coefficients k₃₃ (∼94%) and low dielectric loss factor (∼1%), along with large strain make the crystals promising candidates for a wide range of electromechanical transducers.     

Dielectric, ferroelectric and piezoelectric properties of Bi0.5Na0.5TiO3-(Ba0.7Ca0.3)TiO3 ceramics at morphotropic phase boundary composition

(1 − x)Bi_0.5Na_0.5TiO₃-x(Ba_0.7Ca_0.3)TiO₃ (BNT-xBCT, 0 ≤ x ≤ 0.15) solid solutions have been synthesized by a conventional solid state sintering method for obtaining a morphotropic phase boundary (MPB) with good piezoelectric properties. X-ray diffraction patterns reveal that a MPB of rhombohedral and tetragonal phases is formed at compositions 0.09 ≤ x ≤ 0.12. Addition of BCT into BNT greatly lowered coercive field E_c without degrading remanent polarization P_r. The specimen with x = 0.09 has the good piezoelectric properties: d₃₃ = 125 pC/N and k_p = 0.33. A modified Curie-Weiss law was used to fit the dielectric constant of BNT-xBCT ceramics, and a frequency dispersion was observed during the phase transitions from antiferroelectric to paraelectric in specimens with x exceeding 0.06.     

Effect of Pb(Zn1 / 2W1 / 2)O3 introduction on perovskite development and dielectric properties of (Ba,Pb)TiO3

Powders of a Pb(Zn_1 / 2W_1 / 2)O₃-introduced BaTiO₃-PbTiO₃ system were prepared. A two-step calcination route of a B-site precursor method was employed to promote perovskite formation. The overall effects of the Pb(Zn_1 / 2W_1 / 2)O₃ incorporation on changes in crystalline aspects as well as dielectric properties were explored.     

Preparation and dielectric properties of BaCu(B2O5)-doped SrTiO3-based ceramics for energy storage

BaCu(B₂O₅) (BCB) was used as sintering aids to lower the sintering temperature of multi-ions doped SrTiO₃ ceramics effectively from 1300 °C to 1075 °C by conventional solid state method. The effect of BCB content on crystalline structures, microstructures and properties of the ceramics was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and dielectric measurements, respectively. The addition of BCB enhanced the breakdown strength (BDS) while did not sacrifice the dielectric constant. The enhancement of BDS should be due to the modification of microstructures, i.e., smaller and more homogeneous grain sizes after BCB addition. The dielectric constant of BCB-doped ceramics maintained a stable value with 1.0 mol% BCB, which was dominated by the combination of two opposite effects caused by the presence of second phases and the incorporation of Cu²⁺ and Ba²⁺, while further increase was owing to the increase of dissolved Ba²⁺ ions when the content of BCB is more than 2.0 mol%. The multi-ions doped SrTiO₃ ceramics with 1.0 mol% BCB addition showed optimal dielectric properties as follows: dielectric constant of 311.37, average breakdown strength of 28.78 kV/mm, discharged energy density of 1.05 J/cm³ and energy efficiency of 98.83%.     

Distribution of pyrochlore phase in Pb(Mg1/3Nb2/3)O3-PbTiO3 films and suppression with a Pb(Zr0.52Ti0.48)O3 interfacial layer

Thin films of the relaxor ferroelectric Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) on Pt/Ti/SiO₂/Si (Pt/Si) substrates both with and without a Pb(Zr_0.52Ti_0.48)O₃ (PZT) interfacial layer were investigated. Perovskite and pyrochlore coexistence was observed for PMN-PT thin films without a PZT interfacial layer. Interestingly, most of the pyrochlore phase was observed in single-coated films and in the first layer of multi-coated films. The pyrochlore phase exhibited grains with an average size of about 25 nm, which is smaller than those of the perovskite phase (about 90 nm). In contrast, for PMN-PT thin films grown on a PZT interfacial layer, the formation of a pyrochlore phase at the interface between PMN-PT layers and the substrate is completely suppressed. Moreover, small grains are not observed in the films with a PZT interfacial layer. The measured polarization-electric field (P-E) hysteresis loops of PMN-PT films with and without PZT layers indicate that enhanced electrical properties can be obtained when a PZT interfacial layer is used. These enhanced properties include an increase in the value of remanent polarization P_r from 2.7 to 5.8 μC/cm² and a decrease in the coercive field E_c from 60.5 to 28.0 kV/cm.     

Effect of CuO addition to Nd(Zn1/2Ti1/2)O3 ceramics on sintering behavior and microwave dielectric properties

The microwave dielectric properties and microstructures of CuO-doped Nd(Zn_1/2Ti_1/2)O₃ ceramics prepared by the conventional solid-state route were investigated. The prepared Nd(Zn_1/2Ti_1/2)O₃ exhibits a mixture of Zn and Ti showing 1:1 order in the B-site. As an appropriate sintering aid, not only did CuO lower the sintering temperature, it could effectively hold back the evaporation of Zn in the Nd(Zn_1/2Ti_1/2)O₃. Moreover, CuO only resided in boundaries, which was confirmed by EDX analysis. The measured lattice parameters of CuO-doped Nd(Zn_1/2Ti_1/2)O₃ (a = 5.4652 ± 0.0005 ?, b = 5.6399 ± 0.0007 ?, c = 7.7797 ± 0.0008 ? and β = 90.01 ± 0.01°) retained identical to that of the pure Nd(Zn_1/2Ti_1/2)O₃ in all cases. In comparison with the pure Nd(Zn_1/2Ti_1/2)O₃ ceramics, specimen with 1 wt.% CuO addition possesses a compatible combination of dielectric properties with a ε_r of 30.68, a Q × f of 158,000 GHz (at 8 GHz) and a τ_f of − 45 ppm/°C at 1270 °C. It also indicated a 60 °C lowering in the sintering temperature. The proposed dielectrics can be a very promising candidate material for microwave or millimeter wave applications requiring extremely low dielectric loss.     

Effect of LaNiO3 electrodes and lead oxide excess on chemical solution deposition derived Pb(Zrx,Ti1 − x)O3 films

The effects of LaNiO₃ (LNO) and Pt electrodes on the properties of Pb(Zr_x,Ti_1 − x)O₃ (PZT) films were compared. Both LNO and PZT were prepared by chemical solution deposition (CSD) methods. Specifically, the microstructure of LNO and its influence on the PZT properties were studied as a function of PbO excess. Conditions to minimize the Pyrochlore phase and porosity were found. Remnant polarization, coercive field and fatigue limit were improved in the PZT/LNO films relative to the PZT/Pt films. Additionally, the PZT crystallization temperature over LNO was 500 °C, about ~ 50 °C lower than over Pt. The crystallization temperature reported here is amongst the lowest values for CSD-based PZT films.     

Crystal structure and ferroelectric properties of Ca(Cu3−xMx)Ti4O12 (M = Fe and Ni) ceramics

M-substituted Ca(Cu_3−xM_x)Ti₄O₁₂ (CCMTO) ceramics, where M = Fe and Ni, were synthesized and the influence of M substitutions for Cu on the crystal structure and ferroelectric properties of CCMTO ceramics were investigated in this study. From the variations in the lattice parameters of CCMTO ceramics, the solubility limit of Ni substitution for Cu in CaCu_3−xNi_xTi₄O₁₂ (CCNTO) ceramics was x = 0.2, whereas that of CaCu_3−xFe_xTi₄O₁₂ (CCFTO) ceramics was x = 0.05. The crystal structural analysis of CCMTO ceramics revealed that the single phase of CCMTO ceramics belongs to the I23 non-centrosymmetric space group of I23; as a result, the P_r and E_c values of CCFTO ceramics at x = 0.05 were 1.8 μC/cm² and 40 kV/cm, respectively. The ferroelectric behavior of CCMTO ceramics by the M substitutions for Cu may be related to the displacement of a Ti⁴⁺ cation in the TiO₆ octahedra and tilting of the Ti–O–Ti angle because of the non-centrosymmetric space group.     

Effects of Mn doping on the structure and electrical properties of high-temperature BiScO3-PbTiO3-Pb(Zn1/3Nb2/3)O3 piezoelectric ceramics

The effects of Mn addition on the structure, ferroelectric, and piezoelectric properties of the 0.35BiScO₃-0.60PbTiO₃-0.05Pb(Zn_1/3Nb_2/3)O₃ ceramics were studied. The results demonstrate that the addition of small amounts of Mn did not cause a remarkable change in crystal structure, but resulted in an evident evolution in microstructure and ferro-piezoelctric properties. The addition of Mn can induce combinatory “hard” and “soft” piezoelectric characteristics due to aliovalent substitutions. The optimal electrical properties are obtained in the 0.25 mol% Mn-doped composition with a high Curie temperature, indicating that Mn doping contributes to the electrical properties of the ceramics. It can be expected that the improved piezoelectric material can be a promising candidate for high-temperature piezoelectric applications.     

Self-controlled growth of Fe3BO6 crystallites in shape of nanorods from iron-borate glass of small templates

Fe₃BO₆ can be an ideal compound for devising functional magnetic and dielectric properties in a single material for multiple applications such as electrodes, gas sensors, or medical tools. Useful to tailor such properties, here we report on a self-controlled Fe₃BO₆ growth in a specific shape of nanorods from a supercooled liquid precursor (an inorganic polymeric liquid or glass) of an initial composition (100 − x)B₂O₃ − xFe₂O₃, x = 40–50 mol%. B₂O₃ as a strong glass former co-bridges the Fe³⁺ ions in oxygen polygons primarily in a 2-D interconnected polymer network so that it dictates preferably a 1-D directional growth on the reaction Fe³⁺ species in form of a compound Fe₃BO₆, a favorable phase to nucleate and grow when annealing a precursor at 500–800 °C in ambient air. Distinct nanorods with a diameter ∼200 nm and 40–100 μm length have been formed on 10–15 min annealing a sample in microwave at moderate temperature 550 °C. A bonded surface B₂O₃ layer (15–25 nm thickness) has grown on the Fe₃BO₆ of the nanorods in situ in a specific structure. XPS bands in the Fe³⁺, B³⁺ and O²⁻ species confer this model structure. A local BO₃ → BO₄ conversion has incurred in the boroxol (B₃O_4.5)_n, n → ∞, rings in the surface layer, showing three distinct IR bands at 1035, 1215 and 1425 cm⁻¹.     

Effect of chromium substitution on structure and magnetic properties of Bi2Fe4O9

Orthorhombic Bi₂Fe_4 − xCr_xO₉ (x = 0.0, 0.25, and 0.75) nanoplatelets were synthesized by a simple hydrothermal method. The structure, morphology, and magnetic properties of the obtained powders have been characterized. Calculation of the lattice parameters of Bi₂Fe_4 − xCr_xO₉, as well as bond lengths and angles, was carried out by X-ray diffraction Rietveld refinement. The volumes of the metal-oxygen tetrahedra and octahedra were calculated to be sequentially increasing as the Cr doping level increases. The samples undergo an antiferromagnetic transition at 250 ± 5 K. The magnetic moments of the samples increase with higher Cr doping level. The 3d electron spin state for Fe³⁺ in the as-prepared samples is different, which is possibly due to the distortion of Fe-O tetrahedra and octahedra in the crystal structure after chromium substitution.     

Correlation of crystal structure and microwave dielectric properties for Zn(Ti1−xSnx)Nb2O8 ceramics

The correlation of crystal structure and microwave dielectric properties for Zn(Ti_1−xSn_x)Nb₂O₈ ceramics were investigated. The Zn(Ti_1−xSn_x)Nb₂O₈ ceramics contained ZnTiNb₂O₈ and an unknown Columbite-type phase. The columbite structure phase with increasing degree of ordering led to decrease of dielectric constant, increase of Qf and τ_f. The ZnTiNb₂O₈ with decreasing cation valence led to increase of τ_f. The typical values were: ? = 30.88, Qf = 43,500 GHz, τ_f = −54.32 × 10⁻⁶/ °C.     

Composition dependent phase connectivity, dielectric and magnetoelectric properties of magnetoelectric composites with Pb(Mg1/3Nb2/3)0.67Ti0.33O3 as piezoelectric phase

Ferrite (Ni_0.6Co_0.4Fe₂O₄) phase, ferroelectric (Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃) phase and magnetoelectric composites of (x)Ni_0.6Co_0.4Fe₂O₄ + (1 − x)Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ with x = 0.15, 0.30 and 0.45 were prepared using solid-state reaction technique. Presence of Ni_0.6Co_0.4Fe₂O₄ and Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ was confirmed using X-ray diffraction technique. The scanning electron microscopic images were used to study the microstructure of the composites. Connectivity scheme present in the magnetoelectric (ME) composites are discussed from the microscopic images. Variation of dielectric constant and dielectric loss with temperature for all the composites was studied. Here we report the effect of Ni_0.6Co_0.4Fe₂O₄ mole fraction on connectivity schemes between Ni_0.6Co_0.4Fe₂O₄ and Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ composite. The variation of magnetoelectric voltage coefficient with dc magnetic field shows peak behaviour. The maximum value of magnetoelectric voltage coefficient of 9.47 mV/cm Oe was obtained for 0.15Ni_0.6Co_0.4Fe₂O₄ + 0.85Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ composites. Finally we have co-related the effect of Ni_0.6Co_0.4Fe₂O₄ content and dielectric properties on magnetoelectric voltage coefficient.