用圆孔内单边裂纹平台巴西圆盘和实验-数值-解析法确定砂岩的动态起裂和扩展韧度

在I型(张开型)动态断裂实验中,利用大直径(?100 mm)分离式霍普金森压杆径向冲击圆孔内单边裂纹平台巴西圆盘试样。考虑了材料惯性效应和裂纹扩展速度对动态应力强度因子的影响,用实验-数值-解析法确定了高加载率和高裂纹扩展速度情况下,砂岩的动态起裂韧度和动态扩展韧度。由动态实验获取试样的动荷载历程,采用裂纹扩展计(Crack Propagation Gauge,CPG)测定试样断裂时刻和裂纹扩展速度,获得裂纹扩展速度对应的普适函数值。然后将动荷载历程带入到有限元软件中进行动态数值模拟,求出静止裂纹的动态应力强度因子历程,再用普适函数值对其进行近似修正。最后根据试样的起裂时刻和穿过CPG中点的时刻,由相应的动态应力强度因子历程分别确定砂岩的动态起裂和动态扩展韧度,它们分别随动态加载率和裂纹扩展速度的提高而增加。     

Effect of loading rate on dynamic fracture initiation toughness of brittle materials

Numerical simulation is carried out to investigate the effect of loading rate on dynamic fracture initiation toughness including the crack-tip constraint. Finite element analyses are performed for a single edge cracked plate whose crack surface is subjected to uniform pressure with various loading rate. The first three terms in the Williams’ asymptotic series solution is utilized to characterize the crack-tip stress field under dynamic loads. The coefficient of the third term in Williams’ solution, A ₃, was utilized as a crack tip constraint parameter. Numerical results demonstrate that (a) the dynamic crack tip opening stress field is well represented by the three term solution at various loading rate, (b) the loading rate can be reflected by the constraint, and (c) the constraint A ₃ decreases with increasing loading rate. To predict the dynamic fracture initiation toughness, a failure criterion based on the attainment of a critical opening stress at a critical distance ahead of the crack tip is assumed. Using this failure criterion with the constraint parameter, A ₃, fracture initiation toughness is determined and in agreement with available experimental data for Homalite-100 material at various loading rate.     

Experimental studies on mixed‐mode dynamic fracture behaviour of aluminium alloy plates with narrow U‐notch

Mixed‐mode dynamic fracture behaviour of cast aluminium alloy ZL205A thin plates with narrow U‐notch was studied by split Hopkinson tensile bar apparatus. Specimens with different loading angles were designed to realize different fracture modes. The same loading condition was maintained during the tests. Recovery specimens show that crack propagates along the notch direction. Force–elongation relations show that with the loading angle increasing, the fracture force increases while the final elongation decreases. Deformation and fracture process was observed by a high‐speed camera. Displacement distribution around the crack was calculated through digital image correlation technique. Based on the photos and displacement results, initiation time of the crack was derived. Besides, two stress components (normal stress and shear stress) applied on the fracture surface were investigated. Results show that crack initiation stresses at different loading angles satisfy the ellipse equation. Pure mode I and II fracture stresses are 425.3 and 236.7 MPa, respectively. Furthermore, specific fracture energy of different specimens was calculated. The energy data vary with loading angle and located on an approximate upward parabolic curve. From the curve, the minimum specific fracture energy of the thin plate specimen is 42.0 kJ/m² under loading angle of 76.3°.     

半圆盘构件冲击断裂特性的动态焦散线实验研究

采用动态焦散线实验系统,对有机玻璃（PMMA）在冲击载荷下的I型和I-II混合型裂纹在起裂和扩展时的动态断裂特性进行了研究。结果表明：随着PMMA由I型断裂转变为I-II混合型断裂,从落锤作用在试件上到裂纹起裂所需时间不断增加,说明裂纹起裂需要的能量有所增加,同时从裂纹起裂到最终贯通所需时间不断减少,说明裂纹平均扩展速度也不断增大;在I型断裂中,PMMA的断裂韧度KIC为2.04 MN/m3/2,而在I-II混合型断裂中,PMMA的断裂韧度KIC低于I型断裂时的断裂韧度KIC,但是KIIC有所增大;对于I-II混合型断裂,PMMA极限扩展速度约为366m/s,当达到极限扩展速度后,裂纹尖端出现微裂纹增韧现象,使裂纹的表面能迅速增大,随后裂纹的扩展速度迅速减小。     

Computational analysis of dynamically propagating cracks in axisymmetric solids

Dynamic crack propagation behavior in axisymmetric solids is investigated using an effective computational procedure. First, an accurate method to extract energy release rate of a dynamically propagating crack from finite element solutions is formulated for axisymmetric geometries. The method is applied to an analysis of a radially growing circular crack under remote tension in an infinite medium. The computed dynamic energy release rate shows an excellent agreement with the exact solution. Next, we have developed an iterative technique to propagate a crack whose velocity history is initially unknown. With the iterative procedure, the crack propagates according to a condition specified by a dynamic fracture criterion. At each increment of crack growth, an optimum velocity at which the crack growth condition satisfies is obtained by the iterative scheme. This procedure requires no artificial input or no preset crack tip speed in a simulation study. The iterative scheme is employed in a dynamic fracture analysis of ceramics. The computational analysis is carried out for simulation of fracture experiments using circumferentially notched round bars. In the test, a ceramic specimen is subjected to tensile stress wave loading and after crack growth initiation, the external crack propagates to tear the specimen. The computational simulation is carried out for the entire fracture process including the crack growth initiation and the dynamic propagation. The iterative procedure enables us to predict the crack tip velocity which is unmeasurable in the experiment. Suitabilities of proposed fracture toughness criteria for the ceramics are investigated by comparing measured and computed transmitted pulses through the uncracked ligament. This study proves the usefulness of the computational procedures for dynamic fracture analysis. It is most effective in characterizing dynamic fracture toughness where determination of every relevant parameter is difficult in the experiments.     

INTERFACIAL CRACK INITIATION UNDER QUASI-STATIC AND DYNAMIC LOADING CONDITIONS: AN EXPERIMENTAL STUDY

Abstract— Interfacial fracture parameters under quasi-static and dynamic loading are examined in a large elastic mismatch bimatenal system. A wide range of remote field loading ratios of shear and tension are considered. The crack tip fields are mapped using the optical method of coherent gradient sensing or CGS and fracture parameters are quantified. Distinctly different crack initiation responses are observed for positive and negative shear stresses acting on the interface. Also, low velocity impact loading experiments are conducted to study the influence of dynamic loading on crack initiation parameters. Dynamic interfacial crack tip fields are recorded using high speed photography and fracture parameters for dynamically loaded stationary cracks are obtained. Measurements suggest significant crack initiation toughness reduction under dynamic loading conditions.     

Dynamic crack initiation toughness of 4340 steel at constant loading rates

Determination of fracture toughness for metals under quasi-static loading conditions can follow well-established procedures and ASTM standards. The use of metallic materials in impact related applications requires the determination of dynamic crack initiation toughness for these materials. There are two main challenges in experiment design that must be overcome before valid dynamic data can be obtained. Dynamic equilibrium over the entire specimen needs to be approximately achieved to relate the crack tip loading state to the far-field loading conditions, and the loading rate at the crack tip should be maintained near constant during an experiment to delineate rate effects on the values of dynamic crack initiation toughness. A recently developed experimental technique for determining dynamic crack initiation toughness of brittle materials has been adapted to measure the dynamic crack initiation toughness of high-strength steel alloys. A Kolsky pressure bar is used to apply the dynamic loading. A pulse shaper is used to achieve constant loading rate at the crack tip and dynamic equilibrium across the specimen. A four-point bending configuration is used at the gage section of the setup. Results are presented which show a monotonically increasing rate dependence of crack initiation toughness for 4340 high-strength steel.     

Determination of dynamic rock Mode-I fracture parameters using cracked chevron notched semi-circular bend specimen

Rock dynamic fractures are common in many geophysical processes and engineering applications. Characterization of rock dynamic fracture properties such as the initiation fracture toughness, the fracture energy, and the fracture velocity, is thus of great importance in rock mechanics. A novel method is proposed in this work to measure dynamic Mode-I rock fracture parameters using a cracked chevron notched semi-circular bend (CCNSCB) specimen loaded by a split Hopkinson pressure bar (SHPB) apparatus. A strain gauge is mounted on the sample surface near the chevron notch to detect the fracture onset, and a laser gap gauge (LGG) is used to monitor the crack surface opening distance (CSOD) during the dynamic test. With dynamic force balance achieved in the tests, the stable–unstable transition of the crack propagation crack is observed and the initiation fracture toughness is calculated from the dynamic peak load. The average dynamic fracture energy as well as the fracture propagation toughness are calculated based on the first law of thermodynamics. The measured dynamic fracture properties of Laurentian granite using CCNSCB method are consistent with those reported in the literature using other methods.     

Impact and dynamic fracture of tough polymers by thermal decohesion in a Dugdale zone

At low temperatures and high loading rates, normally tough crystalline thermoplastics may undergo a transition from ductile tearing to brittle rapid crack propagation (RCP). It is proposed here that RCP — characterised by low toughness, high crack speed (>100 m/s) and a macroscopically smooth fracture surface — occurs by self-sustained melting of a layer, one chain length thick, at each cohesive surface of a crack-tip craze, due to adiabatic heating. Initiation of RCP from a rapidly loaded sharp notch, i.e. impact fracture, requires both the formation of this melt layer, and sufficient crack extension force to propagate it. A schematic linear-elastic analysis based on the Dugdale model accounts both for the measured dynamic fracture resistance, and for the variation of impact fracture resistance with impact speed, in two pipe-grade polyethylenes and in a neat and a rubber-toughened polyacetal. It is concluded that crack initiation resistance, unlike dynamic fracture resistance, cannot be defined as a geometry-dependent material property.     

Quasi-static and dynamic fracture initiation toughness of Ti/TiB layered functionally graded material under thermo-mechanical loading

Quasi-static and dynamic fracture initiation toughness of Ti/TiB layered functionally graded material (FGM) is investigated using a three point bend specimen. The modified split Hopkinson pressure bar (SHPB) apparatus in conjunction with induction coil heating system is used during elevated temperature dynamic loading experiments. A simple and accurate technique has been developed to identify the time corresponding to the load at which the fracture initiates. A series of experiments are conducted at different temperatures ranging from room temperature to 800 °C, and the effect of temperature and loading rate on the fracture initiation toughness is investigated. The material fracture toughness is found to be sensitive to temperature and the fracture initiation toughness increases as the temperature increases. Furthermore, the fracture initiation toughness is strain rate sensitive and is higher for dynamic loading as compared to quasi-static loading.     

Initiation, propagation and arrest of an interface crack subjected to controlled stress wave loading

An experimental study has been conducted to investigate the initiation, propagation, and arrest of bimaterial interface cracks subjected to controlled stress wave loading in the form of a tensile dilatational stress wave pulse. The tensile pulse is generated by detonating lead azide explosive in a specially designed specimen. Dynamic loading of the bimaterial interface results in crack initiation, propagation, and arrest, all in the same experiment. This failure event is observed using photoelasticity in conjunction with high speed photography. Full field data from the experimentally obtained isochromatic fringe patterns is analyzed to determine time histories of various fracture parameters such as the crack tip speed, the dynamic complex stress intensity factor, the energy release rate, and the mixity. The experimental data is also used to quantify the values of the dynamic initiation and arrest toughness and to evaluate a recently proposed dynamic interface fracture criterion. This revised version was published online in August 2006 with corrections to the Cover Date.     

Dynamic fracture of a functionally gradient material having discrete property variation

A functionally gradient material (FGM) with discrete property variation is prepared, and the dynamic fracture in this material is studied using the technique of photoelasticity combined with high-speed photography. Transparent sheets required for the study are made by casting a polyester resin mixed with varying amounts of plasticizer. The mechanical (quasi-static and dynamic) and optical properties of the material are evaluated as a function of the plasticizer content. Results of material characterization show that the fracture toughness increases with increasing plasticizer content, whereas the Young's modulus decreases. The material fringe constant and the dynamic modulus are observed to be relatively insensitive to plasticizer content. The FGM is then prepared by casting together thin strips having different plasticizer content. The dynamic crack propagation phenomenon is studied for four different property variations along the crack propagation direction, and the effects of these property variations on crack speed, crack jump distance and dynamic stress intensity factor are investigated. Results of this investigation show that increasing the toughness in the direction of crack growth reduces the crack jump distance as compared to on increasing-decreasing toughness variation for the same initial energy.     

Experimental Determination of Dynamic Crack Initiation and Propagation Fracture Toughness in Thin Aluminum Sheets

An experimental investigation was undertaken to characterize the dynamic fracture characteristics of 2024-T3 aluminum thin sheets ranging in thickness from 1.63–2.54 mm. Specifically, the critical dynamic stress intensity factor Kdc was determined over a wide range of loading rates ( expressed as the time rate of change of the stress intensity factor KdI ) using both a servo- hydraulic loading frame and a split Hopkinson bar in tension. In addition, the dynamic crack propagation toughness, KD, was measured as a function of crack tip speed using high sensitivity strain gages. A dramatic increase in both Kdc and KD was observed with increasing loading rate and crack tip speed, respectively. These relations were found to be independent of specimen thickness over the range of 1.5 to 2.5 mm.     

Determination of dynamic fracture parameters using a semi-circular bend technique in split Hopkinson pressure bar testing

Fracture initiation toughness, fracture energy, fracture propagation toughness, and fracture velocity are key dynamic fracture parameters. We propose a method to simultaneously measure these parameters for mode-I fractures in split Hopkinson pressure bar (SHPB) testing with a notched semi-circular bend (SCB) specimen. The initiation toughness is obtained from the peak load given dynamic force equilibrium. A laser gap gauge (LGG) is developed to monitor the crack surface opening displacement (CSOD) of the specimen, from which the fracture velocity and the fracture energy can be calculated. The feasibility of this methodology for coarse-grained solids is demonstrated with the SHPB-SCB experiments on Laurentian granite.     

An investigation of the effects of mix strength on the fracture and fatigue behavior of concrete mortar

This paper examines the effects of mix compressive strength (30, 35 and 40 MPa) on the fracture initiation toughness, resistance-curve behavior and fatigue crack growth behavior of concrete mortar. The fracture initiation toughness and the resistance-curve behavior are shown to increase with increasing mix strength. The observed resistance-curve behavior is then attributed largely to the effects of ligament bridging, which are predicted using small- and large-scale bridging models. In contrast, the fatigue crack growth resistance is shown to decrease with increasing mix strength. An extended multiparameter framework was used for the modeling of fatigue crack growth. Finally, the implications of the results are discussed for the design of concrete mixtures with attractive combinations of strength, fracture toughness and fatigue crack growth resistance.     

含倾斜裂纹三点弯动态断裂试验研究

为研究冲击荷载下巷道围岩不同角度径向裂纹的破坏机制,采用落锤冲击加载平台和数字激光动态焦散线实验系统,以有机玻璃为试验材料,设计冲击荷载下半圆孔上不同角度裂纹的三点弯动态断裂试验,记录预制裂纹的角度α的改变对裂纹动态力学行为的影响,通过分析动态应力强度因子和裂纹扩展轨迹的分形维数对实验现象进行归纳总结。研究发现:①预制裂纹角度对裂纹尖端应变能的积累和释放的快慢有较大影响,随着角度的增大,起裂时间变短,起裂更容易,裂纹尖端应变能积累的更快;②裂纹尖端应变能释放的快慢在α=45°两侧表现出不同的规律;③不同角度裂纹的Ⅰ型动态应力强度因子随时间的变化规律具有相似性,但最大值却具有差异性;④不同角度裂纹的扩展轨迹满足一定的分形规律。     

Statistical scatter in the fracture toughness and Charpy impact energy of pearlitic steel

The effect of microstructure on the fracture characteristics of high carbon hypo eutectoid steel was studied under conditions of quasistatic and dynamic loading. Experimentally determined sets of fracture toughness and Charpy impact energy values were statistically treated. A relationship was found between fracture toughness and Charpy impact energy. In the very brittle domain, the fracture toughness increases slightly with increasing Charpy impact energy. In the domain where the fracture toughness is higher, the rise in fracture toughness with increasing Charpy impact energy is more pronounced. Detailed SEM examination of fractured compact tension (CT) and Charpy V-notch (CVN) specimens showed that the fracture at ambient temperature occurred almost exclusively by cleavage. There were no visible differences in the morphology of cleavage facets on the fracture surfaces of Charpy and CT specimens. Mechanisms of cleavage initiation were revealed by the fractographical investigation of fracture surfaces. Whereas the fracture surfaces of broken CT specimens exhibit a number of cleavage origins, the fracture surfaces of CVN specimens usually show only one.     

冲击载荷下CFRP及GFRP层板断裂韧性的研究

利用Hopkinson杆加载装置, 对带有单边切口的炭纤维增强复合材料(CFRP)及玻璃纤维增强复合材料(GFRP)层板试件进行冲击拉伸加载实验。根据一维应力波理论求得作用于试件上的载荷P(t)和试件加载点的位移δ(t)。 根据试样中应力随时间的变化历史σ(t), 并基于断裂韧性测试原理, 建立了动态应力强度因子K_Ⅰ (t)响应曲线。利用柔度变化率方法确定起裂时间, 分别得到在两种加载速率下CFRP、 GFRP层板的动态断裂韧性。结果表明, 随着加载速率的提高, 这两种复合材料的断裂韧性降低。      

Study of mode I crack dynamic propagation behaviour and rock dynamic fracture toughness by using SCT specimens

To study crack dynamic propagation behaviour and rock dynamic fracture toughness, a single cleavage triangle (SCT) specimen was proposed in this paper. By using these specimens and a drop‐weight test system, impact experiments were conducted, and the crack propagation velocity and the fracture time were measured by using crack propagation gauges. To examine the effectiveness of the SCT specimen and to predict the test results, finite difference numerical models were established by using AUTODYN code, and the simulation results showed that the crack propagation path agrees with the test results, and crack arrest phenomena could happen. Meanwhile, by using these numerical models, the crack dynamic propagation mechanism was investigated. Finite element code ABAQUS was applied in the calculation of crack dynamic stress intensity factors (SIFs) based on specimen dimension and the loading curves measured, and the curves of crack dynamic SIFs versus time were obtained. The fracture toughness (including initiation toughness and propagation toughness) was determined according to the fracture time and crack speeds measured by crack propagation gauges. The results show that the SCT specimen is applicable to the study of crack dynamic propagation behaviour and fracture toughness, and in the process of crack propagation, the propagation toughness decreases with crack propagation velocity, and the crack arrest phenomena could happen. The critical SIF of an arrest crack (or arrest toughness) was higher than the crack propagation toughness but was lower than the initiation toughness.     

预加载下岩石的动态力学性能研究

动态和静态载荷共同作用下的岩石力学特性是深部地下岩石工程的关键问题。设计了用于测试静态预加载下岩石动态力学性能的分离式霍普金森压杆系统,并详细介绍了具有预加载装置的分离式霍普金森压杆系统的原理、数据分析和应力波的传播过程。通过具有预加载装置的分离式霍普金森压杆系统研究了岩石在不同预拉伸应力下的拉伸强度。结果表明:动态拉伸强度和总拉伸强度随着加载率的增加而增加,同时,在相同加载率下,动态拉伸强度随着预拉伸载荷的增加而减小,而总拉伸应力与预拉伸载荷的大小无关。此外,对不同预加载条件下岩石的动态断裂韧度也进行了研究,实验结果说明岩石的动态断裂韧度和总断裂韧度随着加载率的增加而增加。在相同加载率下,动态断裂韧度随着预加载荷的增加而减小,而总断裂韧度随着加载率的增加而增加。