Impact strength of Sn–3.0Ag–0.5Cu solder bumps during isothermal aging

In order to investigate the fracture behavior of Sn–3.0Ag–0.5Cu solder bump, solder balls with the diameter of 0.76 mm were soldered on Cu pad in this study, then high speed impact test and static shear test of solder bumps were carried out to measure the joint strength of the soldering interface. The effect of isothermal aging on joint strength as well as fracture behavior of solder bumps was investigated, and the composition of the fracture surface was identified by means of EPMA. The results indicate that the fracture is inside the bulk solder in low speed shear test regardless of the aging effect, thus the maximum load reflects the solder strength rather than the interfacial strength. It is also found that under 1 m/s impact loading, the crack initiation position is changed from solder/Cu₆Sn₅ interface to Cu₃Sn/Cu interface after long time isothermal aging, and the fracture occurs inside the bulk solder accompanying with intermetallic compound in both of the as-soldered and aged joints. The thickened multiple IMC layers during isothermal aging account for the degraded impact resistance, and the change of the solder matrix is another factor for reduced impact resistance owing to Sn residue on the fracture surface.     

Microstructural evolution of a lead-free solder alloy Sn-Bi-Ag-Cu prepared by mechanical alloying during thermal shock and aging

In a previous study, a lead-free solder, Sn-6Bi-2Ag-0.5Cu, was developed by mechanical alloying. The alloy shows great potential as a lead-free solder system. In the present work, the microstructural evolution during thermal shock and aging was examined. In the as-soldered joints small bismuth (1 μm to 2 μm) and Ag₃Sn (1 μm) particles were finely dispersed in a nearly pure tin matrix with a small amount of η-Cu₆Sn₅ phase in the bulk of solder. During thermal shock and aging microstructural evolution occurred with Cu-Sn intermetallic compound (IMC) layer growth at interface, bismuth phase coarsening and Ag₃Sn phase coarsening. The microstructure of the solder appeared to be stable at high temperature. The shear strength of the present solder joint is higher than that of Sn-37Pb and Sn-3.5Ag solders. Shear failure occurred Cu-Sn IMC layer-solder interface and in the bulk of solder.     

Elevated temperature aging of solder joints based on Sn-Ag-Cu: Effects on joint microstructure and shear strength

The shear strength behavior and microstructural effects after aging for 100 h and 1,000 h at 150°C are reported for near-eutectic Sn-Ag-Cu (SAC) solder joints (joining to Cu) made from Sn-3.5Ag (wt.%) and a set of SAC alloys (including Co- and Fe-modified SAC alloys). All joints in the as-soldered and 100-h aged condition experienced shear failure in a ductile manner by either uniform shear of the solder matrix (in the strongest solders) or by a more localized shear of the solder matrix adjacent to the Cu₆Sn₅ interfacial layer, consistent with other observations. After 1,000 h of aging, a level of embrittlement of the Cu₃Sn/Cu interface can be detected in some solder joints made with all of the SAC alloys and with Sn-3.5Ag, which can lead to partial debonding during shear testing. However, only ductile failure was observed in all solder joints made from the Co- and Fe-modified SAC alloys after aging for 1,000 h. Thus, the strategy of modifying a strong (high Cu content) SAC solder alloy with a substitutional alloy addition for Cu seems to be effective for producing a solder joint that retains both strength and ductility for extended isothermal aging at high temperatures.     

Reliability investigation and interfacial reaction of ball-grid-array packages using the lead-free Sn-Cu solder

The interfacial reactions between two Sn-Cu (Sn-0.7Cu and Sn-3Cu, wt.%) ball-grid-array (BGA) solders and the Au/Ni/Cu substrate by solid-state isothermal aging were examined at temperatures between 70°C and 170°C for 0 to 100 days. For the Sn-0.7Cu solder, a (Cu,Ni)₆Sn₅ layer was observed in the samples aged at 70–150°C. After isothermal aging at 170°C for 50 days, the solder/Ni interface exhibited a duplex structure of (Cu,Ni)₆Sn₅ and (Ni,Cu)₃Sn₄. For the Sn-3Cu solder, only the (Cu,Ni)₆Sn₅ layer was formed in all aged samples. Compared to these two Sn-Cu solders, the Cu content in the (Cu,Ni)₆Sn₅ layer formed at the interface increased with the Cu concentration in the Sn-xCu solders. And, the shear strength was measured to evaluate the effect of the interfacial reactions on the mechanical reliability as a function of aging conditions. The shear strength significantly decreased after aging for 1 day and then remained nearly unchanged by further prolonged aging. In all the samples, the fracture always occurred in the bulk solder. Also, we studied the electrical property of Cu/Sn-3Cu/Cu BGA packages with the number of reflows. The electrical resistivity increased with the number of reflows because of an increase of intermetallic compound (IMC) thickness.     

Effect of cooling rate on growth of the intermetallic compound and fracture mode of near-eutectic Sn-Ag-Cu/Cu pad: Before and after aging

Several near-eutectic solders of (1) Sn-3.5Ag, (2) Sn-3.0Ag-0.7Cu, (3) Sn-3.0Ag-1.5Cu, (4) Sn-3.7Ag-0.9Cu, and (5) Sn-6.0Ag-0.5Cu (in wt.% unless specified otherwise) were cooled at different rates after reflow soldering on the Cu pad above 250°C for 60 sec. Three different media of cooling were used to control cooling rates: fast water quenching, medium cooling on an aluminum block, and slow cooling in furnace. Both the solder composition and cooling rate after reflow have a significant effect on the intermetallic compound (IMC) thickness (mainly Cu₆Sn₅). Under fixed cooling condition, alloys (1), (3), and (5) revealed larger IMC thicknesses than that of alloys (2) and (4). Slow cooling produced an IMC buildup of thicker than 10 μm, while medium and fast cooling produced a thickness of thinner than 5 μm. The inverse relationship between IMC thickness and shear strength was confirmed. All the fast- and medium-cooled joints revealed a ductile mode (fracture surface was composed of the β-Sn phase), while the slow-cooled joints were fractured in a brittle mode (fracture surface was composed of Cu₆Sn₅ and Cu₃Sn phases). The effect of isothermal aging at 130°C on the growth of the IMC, shear strength, and fracture mode is also reported.     

Mechanical strength of Sn-3.5Ag-based solders and related bondings

The tensile strengths of bulk solders and joint couples of Sn-3.5Ag-0.5Cu, Sn-3.5Ag-0.07Ni, and Sn-3.5Ag-0.5Cu-0.07Ni-0.01Ge solders and the shear strengths of ball grid array (BGA) specimens, solder-ball-attached Cu/Ni/Au metallized substrates were investigated. The tensile strength of the bulk is degraded by thermal aging. The Ni-containing solder exhibits lower tensile strength than Sn-3.5Ag-0.5Cu after thermal aging. However, the Ni-containing solder joints show greater tensile strength than the Cu/Sn-3.5Ag-0.5Cu/Cu joint. Fracture of the solder joint occurs between the intermetallic compound (IMC) and the solder. The shear strength and fracture mechanism of BGA specimens are the same regardless of solder composition.     

Developing a lead-free solder alloy Sn-Bi-Ag-Cu by mechanical alloying

A new lead free alloy, Sn-6Bi-2Ag-0.5Cu, has been developed by mechanical alloying and has great potential as a lead-free solder system. Initial trials on the manufacture of solder joints with this alloy revealed that a high quality bond with copper could be formed. Its melting range of 193.87°C to 209.88°C is slightly higher than that of eutectic tin-lead solder. Examination of the microstructure of the as-soldered joints revealed that it mainly consists of small bismuth (1 μm to 2 μm) and Ag₃Sn (1 μm) particles finely dispersed in a nearly pure tin matrix with a small amount of η-Cu₆Sn₅ particles. The Cu-Sn intermetallic compound (IMC) layer formed at solder-copper interface is the η-Cu₆Sn₅ phase with grain size of 2 μm. The shear strength of the solder joint is higher than that of Sn-37Pb or Sn-3.5Ag. Under shear loading, fracture occurred at IMC layer-solder interface as well as in the bulk of solder.     

Influence of Cu content on compound formation near the chip side for the flip-chip Sn-3.0Ag-(0.5 or 1.5)Cu solder bump during aging

Sn-Ag-Cu solder is a promising candidate to replace conventional Sn-Pb solder. Interfacial reactions for the flip-chip Sn-3.0Ag-(0.5 or 1.5)Cu solder joints were investigated after aging at 150°C. The under bump metallization (UBM) for the Sn-3.0Ag-(0.5 or 1.5)Cu solders on the chip side was an Al/Ni(V)/Cu thin film, while the bond pad for the Sn-3.0Ag-0.5Cu solder on the plastic substrate side was Cu/electroless Ni/immersion Au. In the Sn-3.0Ag-0.5Cu joint, the Cu layer at the chip side dissolved completely into the solder, and the Ni(V) layer dissolved and reacted with the solder to form a (Cu_1−y,Ni_y)₆Sn₅ intermetallic compound (IMC). For the Sn-3.0Ag-1.5Cu joint, only a portion of the Cu layer dissolved, and the remaining Cu layer reacted with solder to form Cu₆Sn₅ IMC. The Ni in Ni(V) layer was incorporated into the Cu₆Sn₅ IMC through slow solid-state diffusion, with most of the Ni(V) layer preserved. At the plastic substrate side, three interfacial products, (Cu_1−y,Ni_y)₆Sn₅, (Ni_1−x,Cu_x)₃Sn₄, and a P-rich layer, were observed between the solder and the EN layer in both Sn-Ag-Cu joints. The interfacial reaction near the chip side could be related to the Cu concentration in the solder joint. In addition, evolution of the diffusion path near the chip side in Sn-Ag-Cu joints during aging is also discussed herein.     

Effects of Cu contents in Pb-free solder alloys on interfacial reactions and bump reliability of Pb-free solder bumps on electroless Ni-P under-bump metallurgy

Using the screen-printed solder-bumping technique on the electroless plated Ni-P under-bump metallurgy (UBM) is potentially a good method because of cost effectiveness. As SnAgCu Pb-free solders become popular, demands for understanding of interfacial reactions between electroless Ni-P UBMs and Cu-containing Pb-free solder bumps are increasing. It was found that typical Ni-Sn reactions between the electroless Ni-P UBM and Sn-based solders were substantially changed by adding small amounts of Cu in Sn-based Pb-free solder alloys. In Cu-containing solder bumps, the (Cu,Ni)₆Sn₅ phase formed during initial reflow, followed by (Ni,Cu)₃Sn₄ phase formation during further reflow and aging. The Sn3.5Ag solder bumps showed a much faster electroless Ni-P UBM consumption rate than Cu-containing solder bumps: Sn4.0Ag0.5Cu and Sn0.7Cu. The initial formation of the (Cu,Ni)₆Sn₅ phase in SnAgCu and SnCu solders significantly reduced the consumption of the Ni-P UBM. The more Cu-containing solder showed slower consumption rate of the Ni-P UBM than the less Cu-containing solder below 300°C heat treatments. The growth rate of the (Cu,Ni)₆Sn₅ intermetallic compound (IMC) should be determined by substitution of Ni atoms into the Cu sublattice in the solid (Cu,Ni)₆Sn₅ IMC. The Cu contents in solder alloys only affected the total amount of the (Cu,Ni)₆Sn₅ IMC. More Cu-containing solders were recommended to reduce consumption of the Ni-based UBM. In addition, bump shear strength and failure analysis were performed using bump shear test.     

Effect of volume in interfacial reaction between eutectic Sn-3.5% Ag-0.5% Cu solder and Cu metallization in microelectronic packaging

The Sn-3.5Ag-0.5Cu (wt.%) is the most promising replacement for the eutectic tin-lead solder alloy. Here, an investigation has been carried out to compare the interfacial reactions of the Cu pad of a ball grid array (BGA) substrate with molten eutectic Sn-3.5% Ag-0.5% Cu solder having different volumes. Two different sizes of BGA solder balls were used: 760-μm and 500-μm diameter. Scanning electron microscopy (SEM) was used to measure the consumed thickness of the Cu and also the thickness of the intermetallic compound (IMC). The soldering reaction was carried out at 230°C, 240°C, and 250°C for 1 min, 5 min, 10 min, and 20 min. The Cu consumption was much higher for the Sn-Ag-Cu solder with higher volume. On the other hand, the mean thickness of the intermetallics for solder with smaller volume was thicker than that of the bigger solder balls. The Cu₃Sn compound was also observed at the interface between the Cu₆Sn₅ IMCs and Cu substrate for longer reflow for the both solder balls. Larger Cu₆Sn₅ IMCs were observed in the bulk of the solder with bigger volume. A simplistic theoretical approach is carried out to find out the amount of Cu₆Sn₅ IMCs in the bulk of the solder by measurement of the Cu consumption from the substrate and the thickness of the IMCs that form on the interface.     

Microstructure characterization of SnAgCu solder bearing Ce for electronic packaging

The creep-rupture lives of Sn3.8Ag0.7Cu and Sn3.8Ag0.7Cu0.03Ce lead-free solder joints for electronic packaging were investigated, respectively. And the relationship between creep behavior and intermetallic compound (IMC: Ag₃Sn, Cu₆Sn₅, CeSn₃) particles in SnAgCu/SnAgCuCe solder joints has been obtained. Meanwhile, rare earth Ce concentration gradient and retardation effect of Ce on the IMC layer have been observed at the solder/Cu interface. Moreover, aging reaction of Sn and Cu, and the effect mechanism of rare earth Ce on two IMCs (Cu₆Sn₅ and Cu₃Sn) are reported.     

Characterization of the growth of intermetallic interfacial layers of Sn-Ag and Sn-Pb eutectic solders and their composite solders on Cu substrate during isothermal long-term aging

Single shear lap joints were made with four different solders, Sn-Pb and Sn-Ag eutectic solders, and their composites containing about 20 vol.% in-situ Cu6Sn5 intermetallic phases about 3–8 micrometers in diameter. Two sets of experiments were performed: In the first set, all of the above four solder joints were aged at 150°C for periods ranging to 5000 h and the intermetallic growth was monitored periodically. In the second set, each of the above four solder joints was aged at five different temperatures for 4000 h. The interfacial layers between solders and the Cu substrate were examined using optical and scanning electron microscopy. The growth kinetics of intermetallic interfacial layers formed between solder and Cu substrate was characterized. The effect of in-situ Cu₆Sn₅ intermetallic phases on the growth rate is discussed. The growth rate of the intermetallic layers in the eutectic Sn-Pb composite was slower for the first 150 h as compared to the eutectic Sn-Pb non-composite. The growth rate of the intermetallic layers were similar for both the eutectic Sn-Ag and eutectic Sn-Ag composite throughout the aging duration. The activation energies for Cu₆Sn₅ layer growth for the eutectic Sn-Pb and Sn-Ag solder joints are evaluated to be 111 kJ/mol and 116 kJ/mol, respectively. The eutectic Sn-Pb and Sn-Ag composite solder joints exhibit higher activation energies of 161 kJ/mol and 203 kJ/mol.     

elemental redistribution and interfacial reaction mechanism for the flip chip Sn-3.0Ag-(0.5 or 1.5)Cu solder bump with Al/Ni(V)/Cu under-Bump metallization during aging

In flip chip technology, Al/Ni(V)/Cu under-bump metallization (UBM) is currently applicable for Pb-free solder, and Sn−Ag−Cu solder is a promising candidate to replace the conventional Sn−Pb solder. In this study, Sn-3.0Ag-(0.5 or 1.5)Cu solder bumps with Al/Ni(V)/Cu UBM after assembly and aging at 150°C were employed to investigate the elemental redistribution, and reaction mechanism between solders and UBMs. During assembly, the Cu layer in the Sn-3.0Ag-0.5Cu joint was completely dissolved into solders, while Ni(V) layer was dissolved and reacted with solders to form (Cu_1−y,Ni_y)₆Sn₅ intermetallic compound (IMC). The (Cu_1−y,Ni_y)₆Sn₅ IMC gradually grew with the rate constant of 4.63 × 10⁻⁸ cm/sec^0.5 before 500 h aging had passed. After 500 h aging, the (Cu_1−y,Ni_y)₆Sn₅ IMC dissolved with aging time. In contrast, for the Sn-3.0Ag-1.5Cu joint, only fractions of Cu layer were dissolved during assembly, and the remaining Cu layer reacted with solders to form Cu₆Sn₅ IMC. It was revealed that Ni in the Ni(V) layer was incorporated into the Cu₆Sn₅ IMC through slow solid-state diffusion, with most of the Ni(V) layer preserved. During the period of 2,000 h aging, the growth rate constant of (Cu_1−y,Ni_y)₆Sn₅ IMC was down to 1.74 × 10⁻⁸ cm/sec^0.5 in, the Sn-3.0Ag-1.5Cu joints. On the basis of metallurgical interaction, IMC morphology evolution, growth behavior of IMC, and Sn−Ag−Cu ternary isotherm, the interfacial reaction mechanism between Sn-3.0Ag-(0.5 or 1.5)Cu solder bump and Al/Ni(V)/Cu UBM was discussed and proposed.     

Kinetics of Intermetallic Compound Formation at the Interface Between Sn-3.0Ag-0.5Cu Solder and Cu-Zn Alloy Substrates

The growth kinetics of an intermetallic compound (IMC) layer formed between Sn-3.5Ag-0.5Cu (SAC) solders and Cu-Zn alloy substrates was investigated for samples aged at different temperatures. Scallop-shaped Cu₆Sn₅ formed after soldering by dipping Cu or Cu-10 wt.%Zn wires into the molten solder at 260°C. Isothermal aging was performed at 120°C, 150°C, and 180°C for up to 2000 h. During the aging process, the morphology of Cu₆Sn₅ changed to a planar type in both specimens. Typical bilayer of Cu₆Sn₅ and Cu₃Sn and numerous microvoids were formed at the SAC/Cu interfaces after aging, while Cu₃Sn and microvoids were not observed at the SAC/Cu-Zn interfaces. IMC growth on the Cu substrate was controlled by volume diffusion in all conditions. In contrast, IMC growth on Cu-Zn specimens was controlled by interfacial reaction for a short aging time and volume diffusion kinetics for a long aging time. The growth rate of IMCs on Cu-Zn substrates was much slower due to the larger activation energy and the lower layer growth coefficient for the growth of Cu-Sn IMCs. This effect was more prominent at higher aging temperatures.     

Effect of Isothermal Aging and Thermal Cycling on Interfacial IMC Growth and Fracture Behavior of SnAgCu/Cu Joints

The growth behavior of interfacial intermetallic compounds (IMCs) of SnAgCu/Cu soldered joints was investigated during the reflow process, isothermal aging, and thermal cycling with a focus on the influence of these parameters on growth kinetics. The SnAgCu/Cu soldered joints were isothermally aged at 125°C, 150°C, and 175°C while the thermal cycling was performed within the temperature ranges from −25°C to 125°C and −40°C to 125°C. It was observed that a Cu₆Sn₅ layer formed, followed by rapid coarsening at the solder/Cu interface during reflowing. The grain size of the interfacial Cu₆Sn₅ was found to increase with aging time, and the morphology evolved from scallop-like to needle-like to rod-like and finally to particles. The rod-like Ag₃Sn phase was formed on the solder side in front of the previously formed Cu₆Sn₅ layer. However, when subject to an increase of the aging time, the Cu₃Sn phase was formed at the interface of the Cu₆Sn₅ layer and Cu substrate. The IMC growth rate increased with aging temperature for isothermally aged joints. During thermal cycling, the thickness of the IMC layer was found to increase with the number of thermal cycles, although the growth rate was slower than that for isothermal aging. The dwell time at the high-temperature end of the thermal cycles was found to significantly influence the growth rate of the IMCs. The growth of the IMCs, for both isothermal aging and thermal cycling, was found to be Arrhenius with aging temperature, and the corresponding diffusion factor and activation energy were obtained by data fitting. The tensile strength of the soldered joints decreased with increasing aging time. Consequently, the fracture site of the soldered joints migrated from the solder matrix to the interfacial Cu₆Sn₅ layer. Finally, the shear strength of the joints was found to decrease with both an increase in the number of thermal cycles and a decrease in the dwell temperature at the low end of the thermal cycle.     

Investigation of soldering process and interfacial microstructure evolution for the formation of full Cu3Sn joints in electronic packaging

Within electronic products, solder joints with common interfacial structure of Cu/IMCs/Sn-based solders/IMCs/Cu cannot be used under high temperature for relatively low melting points of Sn-based solders (200–300 °C). However, there is a trend for solder joints to service under high temperature because of the objective for achieving multi-functionality of electronic products.With the purpose of ensuring that solder joints can service under high temperature, full Cu₃Sn solder joints with the interfacial structure of Cu/Cu₃Sn/Cu can be a substitute due to the high melting point of Cu₃Sn (676 °C). In this investigation, soldering process parameters were optimized systematically in order to obtain such joints. Further, interfacial microstructure evolution during soldering was analyzed. The soldering temperature of 260 °C, the soldering pressure of 1 N and the soldering time of 5 h were found to be the optimal parameter combination. During soldering of 260 °C and 1 N, the Cu₆Sn₅ precipitated first in a planar shape at Cu-Sn interfaces, which was followed by the appearance of planar Cu₃Sn between Cu and Cu₆Sn₅. Then, the Cu₆Sn₅ at opposite sides continued to grow with a transition from a planar shape to a scallop-like shape until residual Sn was consumed totally. Meanwhile, the Cu₃Sn grew with a round-trip shift from a planar shape to a wave-like shape until the full Cu₃Sn solder joint was eventually formed at 5 h. The detailed reasons for the shape transformation in both Cu₆Sn₅ and Cu₃Sn during soldering were given. Afterwards, a microstructure evolution model for Cu-Sn-Cu sandwich structure during soldering was proposed. Besides, it was found that no void appeared in the interfacial region during the entire soldering process, and a discuss about what led to the formation of void-free joints was conducted.     

Effect of displacement rate on ball shear properties for Sn–37Pb and Sn–3.5Ag BGA solder joints during isothermal aging

The interfacial reactions and ball shear properties of ball grid array (BGA) solder joints aged at 170 °C for up to 21 days were investigated with different displacement rates. Two different kinds of solders, Sn–37Pb and Sn–3.5Ag (all wt.%), and an electroplated Ni/Au BGA substrate were employed in this work. A continuous Ni₃Sn₄ intermetallic compound (IMC) layer was formed at the interfaces between both the Sn–37Pb and Sn–3.5Ag solders and the substrate during reflow. After aging, two different reaction layers, consisting of (Au_xNi_1−x)Sn₄ IMC and Pb-rich phase, were additionally observed between the Sn–37Pb solder and the Ni₃Sn₄ IMC layer. The thicknesses of these interfacial reaction layers increased with increasing aging time. After reflow, all the fractures occurred inside the bulk solder. The fracture location of the Sn–37Pb solder joints was shifted toward the solder/Ni interface with increasing aging time and displacement rate, whereas the fracture of the Sn–3.5Ag solder joints mainly occurred inside the bulk solder, irrespective of the aging time and displacement rate. Consequently, the shear properties of the Sn–37Pb solder joints significantly decreased with increasing aging time, whereas those of the Sn–3.5Ag solder joints slightly decreased. The tendency toward brittle fracture of the Sn–37Pb solder joints was intensified with increasing displacement rate. The shear properties of the ductile solder joints increased with increasing displacement rate, while the displacement until fracture, deformation energy and displacement rate sensitivity of the brittle solder joints significantly decreased with increasing displacement rate.     

The nanoindentation characteristics of Cu<Subscript>6</Subscript>Sn<Subscript>5</Subscript>, Cu<Subscript>3</Subscript>Sn,and Ni<Subscript>3</Subscript>Sn<Subscript>4</Subscript> intermetallic compounds in the solder bump

In general, formation and growth of intermetallic compounds (IMCs) play a major role in the reliability of the solder joint in electronics packaging and assembly. The formation of Cu-Sn or Ni-Sn IMCs have been observed at the interface of Sn-rich solders reacted with Cu or Ni substrates. In this study, a nanoindentation technique was employed to investigate nanohardness and reduced elastic moduli of Cu₆Sn₅, Cu₃Sn, and Ni₃Sn₄ IMCs in the solder joints. The Sn-3.5Ag and Sn-37Pb solder pastes were placed on a Cu/Ti/Si substrate and Ni foil then annealed at 240°C to fabricate solder joints. In Sn-3.5Ag joints, the magnitude of the hardness of the IMCs was in the order Ni₃Sn₄>Cu₆Sn₅>Cu₃Sn, and the elastic moduli of Cu₆Sn₅, Cu₃Sn, and Ni₃Sn₄ were 125 GPa, 136 GPa, and 142 GPa, respectively. In addition, the elastic modulus of the Cu₆Sn₅ IMC in the Sn-37Pb joint was similar to that for the bulk Cu₆Sn₅ specimen but less than that in the Sn-3.5Ag joint. This might be attributed to the strengthening effect of the dissolved Ag atoms in the Cu₆Sn₅ IMC to enhance the elastic modulus in the Sn-3.5Ag/Cu joint.     

The formation and growth of intermetallics in composite solder

The formation and growth of intermetallics at the solder/substrate interface are factors affecting the solderability and reliability of electronic solder joints. This study was performed to better understand the diffusion behavior and microstructural evolution of Cu−Sn intermetallics at the composite solder/copper substrate interface for eutectic solder and solder alloys containing particle additions of Cu, Cu₃Sn, Cu₆Sn₅, Ag, Au, and Ni. Annealing temperatures of 110 to 160°C were used with aging times of 0 to 64 days. The copper-containing composite solders generally formed thinner Cu₆Sn₅ layers, but thicker Cu₃Sn layers than were formed by the eutectic solder alone. These copper-containing additions, therefore, resulted in increased activation energies for Cu₆Sn₅ formation and decreased activation energies for Cu₃Sn formation as compared to the eutectic solder. The activation energy for Cu₃Sn formation decreased relative to eutectic solder for silver and gold composite solders even though less Cu₃Sn was formed at the substrate interface. Nickel and palladium drastically reduced the Cu₃Sn thickness and increased the Cu₆Sn₅ thickness. However, the Cu₆Sn₅ contained a substantial volume fraction of voids close to the copper substrate. We propose two mechanisms to explain the effects of the copper-containing and silver particles on the kinetics of intermetallic formation. First, the particles act as tin-sinks which remove tin from the solder and decrease the amount of tin available for reaction at the solder/substrate interface. Second, the particles reduce the cross-sectional area available for tin diffusion, which also reduces the amount of tin available at the interface for reaction.     

Shear strength and fracture surface analysis of Sn58Bi/Cu solder joints under a wide range of strain rates

The influences of the strain rate on the shear strength and failure mode of Sn58Bi/Cu solder joints were investigated. After reflowing, some Kirkendall voids were observed at the neighborhood of the Cu₃Sn/Cu interface or in the inner Cu₃Sn layer. In addition, another type of void could also be observed inside the Sn58Bi eutectic solders, and its size was much larger than that of Kirkendall voids. Some Bi particles were obviously found to segregate at the interface between the Cu-Sn IMC and the Sn58Bi solder. The single lap shear test results indicated that the strain rate had an important influence on the shear strength and failure mode of Sn58Bi/Cu solder joints. The shear strength of joints demonstrated increment at first and then decrement as the strain rate increased from 3.33 × 10⁻⁴ s⁻¹ to 3.33 s⁻¹. It was observed that all Sn58Bi/Cu solder joints broke in a mixed-type fracture mode under a wide range of strain rates. Additionally, more broken IMC grains were exposed on the fracture face and more fracture occurred within the IMC layer with increasing strain rate. Furthermore, the fracture path gradually moved from the solder side to the inner IMC side as the strain rate increased.