CdTe/Si复合衬底Ex-situ退火研究

复合衬底CdTe/ZnTe/Si的晶体质量是导致随后外延的HgCdTe外延膜高位错密度的主要原因之一,因此如何提高复合衬底CdTe/Si晶体质量是确保硅基碲镉汞走上工程化的关键所在。降低复合衬底CdTe/Si位错密度方法一般有:生长超晶格缓冲层、衬底偏向、In-situ退火和Ex-situ退火等,本文主要研究Ex-situ退火对复合衬底CdTe/Si晶体质量的影响。研究表明复合衬底经过Ex-situ退火后位错密度最好值达4.2×105cm-2,双晶半峰宽最好值达60arcsec。     

Si基CdTe复合衬底分子束外延研究

文章引入晶格过渡的Si/ZnTe /CdTe作为复合外延基底材料,以阻挡Si/HgCdTe之间大晶格失配产生的高密度位错。通过对低温表面清洁化、面极性控制和孪晶抑制等的研究,解决了Si基CdTe分子束外延生长中诸多的技术难题。在国内首次采用分子束外延(MBE)的方法获得了大面积的Si基CdTe复合衬底材料,对应厚度为4～4. 4μm Si/CdTe (211)样品双晶半峰宽的统计平均结果为83弧秒,与相同厚度的GaAs/CdTe (211)双晶平均水平相当。     

Si/CdTe复合衬底HgCdTe液相外延材料的生长与性能分析

通过改进推舟液相外延技术,成功地在(211)晶向Si/CdTe复合衬底上进行了HgCdTe液相外延生长,获得了表面光亮的HgCdTe外延薄膜.测试结果表明,(211)Si/CdTe复合衬底液相外延HgCdTe材料组分及厚度的均匀性与常规(111)CdZnTe衬底HgCdTe外延材料相当;位错腐蚀坑平均密度为(5～8)×105 cm-2,比相同衬底上分子束外延材料的平均位错密度要低一个数量级;晶体的双晶半峰宽达到70″左右.研究结果表明,在发展需要低位错密度的大面积长波HgCdTe外延材料制备技术方面,Si/CdTe复合衬底HgCdTe液相外延技术可发挥重要的作用.     

Si/CdTe复合衬底HgCdTe液相外延材料的生长与性能分析

通过改进推舟液相外延技术,成功地在(211)晶向Si/CdTe复合衬底上进行了HgCdTe液相外延生长,获得了表面光亮的HgCdTe外延薄膜.测试结果表明,(211)Si/CdTe复合衬底液相外延HgCdTe材料组分及厚度的均匀性与常规(111)CdZnTe衬底HgCdTe外延材料相当;位错腐蚀坑平均密度为(5～8)×105 cm-2,比相同衬底上分子束外延材料的平均位错密度要低一个数量级;晶体的双晶半峰宽达到70″左右.研究结果表明,在发展需要低位错密度的大面积长波HgCdTe外延材料制备技术方面,Si/CdTe复合衬底HgCdTe液相外延技术可发挥重要的作用.     

Si基碲镉汞分子束外延工艺优化研究

报道了Si基碲镉汞(MCT)分子束外延(MBE)的最新研究进展,通过使用反射式高能电子衍射(RHEED)、高温计的在线测量建立和优化了3 in Si基碲镉汞生长温度曲线;通过二次缓冲层的生长进一步降低了界面能,获得的Si基HgCdTe材料在8μm的厚度下半峰宽达到90.72 arcsec,原生片位错密度(EPD)小于1×107 cm-2;采用此材料成功制备出了高性能的中波Si基1280×1024碲镉汞探测器。     

Si基CdTe/HgCdTe分子束外延材料的位错抑制

基于GaAs/Si材料中位错的运动反应理论,修正获得CdTe/Si和HgCdTe/Si外延材料中的位错运动反应模型.采用快速退火方法对Si基HgCdTe外延材料进行位错抑制实验研究,实验结果与理论曲线基本吻合,从理论角度解释了不同高温热处理条件对材料体内位错的抑制作用.对于厚度为4～10μnn的CdTe/Si进行500...     

优质GaAs/Si材料的研制

用国产分子束外延设备(Ⅳ型)在p型Si衬底上用三阶段生长法生长出优质GaAs外延层。测试样品为2μm厚,n型掺杂浓度5×10~(16)cm~(-3)。测量结果为x射线双晶衍射回摆曲线半峰宽225弧秒;低温光荧光谱半峰宽在10K时为5meV,外延层表面位错密度10~6cm~(-2)。     

射频溅射ZnO作缓冲层的HVPE法生长GaN厚膜

在低温HVPE-GaN/c-Al2O3模板上射频溅射ZnO作为缓冲层,采用氢化物气相外延(HVPE,hydridevapoarphaseepitaxy)法外延生长了高质量的GaN320μm厚膜。用高分辨率双晶X射线衍射仪(DCXRD)、原子力显微镜(AFM)和扫描电子显微镜(SEM)分析了制备的GaN厚膜特性。结果表明,GaN(0002)面的X射线摇摆曲线衍射峰半高宽(FWHM)为336.15arcsec,穿透位错密度(TDD)为107cm-2,外延生长的GaN厚膜晶体质量较好,可以作为自支撑GaN衬底。     

分子束外延HgCdTe薄膜的CdTe缓冲层特性研究

CdTe是GaAs衬底上分子束外延(MBE)HgCdTe薄膜时的缓冲层,引入缓冲层的目的是减小失配位错,CdTe缓冲层的生长直接影响到后续HgCdTe薄膜的制备质量,然而目前现有文献鲜有报道CdTe缓冲层的最佳厚度.采用X射线双晶衍射、位错腐蚀坑密度(EPD)、FT-IR和椭圆偏振光谱的方法,从CdTe缓冲层厚度对位错密度的影响入手,分析并确定了理想的CdTe缓冲层厚度.     

Ge(211)衬底上分子束外延CdTe薄膜

采用分子束外延在3英寸Ge(211)衬底上生长了10 μm厚的CdTe(211)B薄膜.CdTe表面镜面光亮,3英寸范围厚度平均值9.72 μm,偏差0.3 μm;薄膜晶体质量通过X射线双晶迴摆曲线进行评价,FWHM平均值80.23 arcsec,偏差3.03 arcsec; EPD平均值为4.5×106cm-2.通过...     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.