Influence of Mg2N2 powder on microstructures and mechanical properties of AZ31 Mg alloy

In order to obtain an effective and reliable grain refiner for Mg-Al alloys, 1% (mass fraction) Mg3N2 was added into AZ31 Mg alloy. The microstructures of the Mg alloys were studied by optical microscopy, scan electron microscopy and X-ray energy dispersive spectroscopy, and the mechanical properties were determined. The results show that adding a small amount of Mg3N2 to AZ31 Mg alloy can refine the grain size from 103 to 58 μm. The ultimate tensile strength and elongation of AZ31 Mg alloy are 174.1MPa and 8.3%, respectively. After the addition of 1% Mg3N2, the ultimate tensile strength and elongation of AZ31 Mg alloy are increased up to 198.7 MPa and 11.8%, respectively. The grain refinement mechanism is that AIN is formed after Mg3N2 is added.Both A1N and Mg phases are of HCP lattice structure, and the disregistry between Mg phases and AIN along (0001)Mg//(0001)AlN is 3.04%, which is very effective for heterogeneous nucleation.     

Structural and optical characteristics of Al x Ga1- x N/AlN superlattice

AlN/Al_0.3Ga_0.7N superlattices were grown on (0001) sapphire substrate by metal-organic chemical vapor deposition (MOCVD). The superlattice period varies from 6 to 30. The layer thickness of different period stack was designed. GaN or AlGaN template was employed for growing AlN/AlGaN superlattices. Reflectivity, SEM, AFM and XRD data of the Al _x Ga_1-x N/AlN superlattices are presented. It is found that the templates used have an intensive impact on surface roughness and interfacial properties of following AlN/AlGaN superlattices. The result of atomic force microscopy indicates that AlN/AlGaN superlattices grown on GaN template exhibit quasi-two-dimensional growth mode. The resulting superlattice has a smooth surface morphology and distinct interface. No crack is observed in the area of a 2-inch wafer. Supported by the Special Funds for Major State Basic Research Project (973 Project) (Grant No. 2006CB6049), the Hi-tech Research Project (Grant Nos. 2006AA03A103, 2006AA03A118, and 2006AA03A142), the National Natural Science Foundation of China (Grant No. 60676057), and the Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20050284004)     

Preparation and sintering of nano Fe coated Si3N4 composite powders

Fe/Si₃N₄ composite powder was synthesized by the heterogeneous precipitation-thermal reduction process, and then pressed into flakes under a pressure of 10 MPa. Flakes were sintered by pressureless and hot-pressing at 1 600 °C under 0.1 MPa N₂. The chemical composition, phases and microstructure of composite powder and sintered flakes were investigated by energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the structure of composite powders is Si₃N₄ coated by nano Fe. The crystal phases of sintered flakes by pressureless are Fe(Si) compound, SiC and Si₃N₄. The crystal phases of the sintered samples by hot-pressing are Fe, Fe(Si) compound and Si₃N₄. It is found that crystal phases flakes obtained by pressureless and hot-pressing are very different. Foundation item: Project(50804016) supported by the National Natural Science Foundation of China     

Microstructures, mechanical properties and compressive creep behaviors of as-cast Mg-5%Sn-（0-1 .0）%Pb alloys

The microstructures, tensile properties and compressive creep behaviors of Mg-5%Sn-(0–1.0)%Pb (mass fraction) alloys were studied. The microstructures of the Mg-Sn-Pb alloys consist of dendritic α-Mg and Mg₂Sn phase. The addition of Pb can refine the size of Mg₂Sn phase and grain size, reduce the amount of Mg₂Sn phase at grain or inter-dendrite boundaries and change the distribution of Mg₂Sn phase. Pb exists in the Mg₂Sn phase or dissolves in α-Mg matrix. The mechanical properties of the tested alloys at room temperature are improved with the addition of Pb. When the Pb content is over 0.5%, the mechanical properties are decreased gradually. The Mg-5%Sn-0.5%Pb shows the best ultimate tensile strength and elongation, 174 MPa and 14.3%, respectively. However, the compressive creep resistance of the Mg-Sn-Pb alloys is much lower than that of the Mg-Sn binary alloy at 175 °C with applied load of 55 MPa, which means that Pb has negative effects on the compressive creep resistance of the as-cast Mg-Sn alloys.     

Microstructure and mechanical properties of ultrafine grained Mg15Al alloy processed by equal-channel angular pressing

An as-cast magnesium alloy with high Al content Mg15Al was subjected to equal-channel angular pressing (ECAP) through a die with an angle of ϕ=90° at 553 K following route B_c. It is found that the network β-Mg₁₇Al₁₂ phases in the as-cast Mg15Al alloy are broken into small blocks and dispersed uniformly with increasing numbers of pressing passes. Moreover, many nano-sized Mg₁₇Al₁₂ particles precipitate in the ultra-fine α-Mg matrix. The grains are obviously refined. However, the grain structure is inhomogeneous in different areas of the alloy. The average size of the primary phase α-Mg is reduced to about 1 μm while grains of around 0.1–0.2 μm are obtained in some two-phase areas. With additional ECAP passes (up to 8), coarsening of the grains occurs by dynamic recovery. Room temperature tensile tests show that the mechanical properties of Mg15Al alloys are markedly improved after 4 ECAP passes. The ultimate tensile strength and elongation to failure increase from 150 MPa to 269.3 MPa and from 0.05% to 7.4%, respectively. Compared with that after 4 passes, the elongation to failure of the alloy increases but the strength of the alloy slightly decreases after 8 ECAP passes. Fracture morphology of the ECAP-processed alloy exhibits dimple-like fracture characteristics while the as-cast alloy shows quasi-cleavage fractures.     

Mechanical properties and microstructure of as-cast and extruded Mg-（Ce, Nd）-Zn-Zr alloys

1INTRODUCTION Thebeneficialinfluenceofrareearth(RE)metalsontheambientandelevatedtemperature mechanicalpropertiesofmagnesiumalloyhaslongbeenrecognized[13].Recently,Yttriumisaddedto Magnesiumalloytoimproveitstensilestrength andcreepresistance,andsuchinvestigationsatheat resistantmagnesiumalloyhaveledtothede velopmentofWE43andWE54alloys[4,5].Al thoughsuchalloysexhibitgoodpropertiesupto573Kthroughcastingandextruding,therelativelyhighcostofYttriumrestrictstheapplicationof suchalloys.Otherr…     

The Role of Calcium in Microstructural Refinement of AZ91 Magnesium Alloy

The effect of calcium addition on the microstructures of AZ91 magnesium alloy was investigated. It was found that a small amount of calcium in AZ91 allay produced a large decrease in the α- Mg grain size and the dispersed fine β-Mgt7 Alt2 phases. In addition, some Al4Ca particles were found to exist in the AZ91 alloy containing 0.5wt% Ca. EDS analysis and water-quenched technique revealed that the grain-refining mechanism of calcium for the AZ91 alloys was mainly attributed to the role of restricting growth of calcium in the primary α-Mg crystals.     

Characteristics of LiCoO2, LiMn2O4 and LiNi0.45Co0.1Mn0.45O2 as cathodes of lithium ion batteries

LiNi_0.45Co_0.10Mn_0.45O₂ was synthesized from Li₂CO₃ and a triple oxide of nickel, cobalt and manganese at 950 °C in air. The structures and characteristics of LiNi_0.45Co_0.10Mn_0.45O₂, LiCoO₂ and LiMn₂O₄ were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi_0.45Co_0.10Mn_0.45O₂ has a layered structure with hexagonal lattice. The commercial LiCoO₂ has sphere-like appearance and smooth surfaces, while the LiMn₂O₄ and LiNi_0.45Co_0.10Mn_0.45O₂ consist of cornered and uneven particles. LiNi_0.45Co_0.10Mn_0.45O₂ has a large discharge capacity of 140.9 mA · h/g in practical lithium ion battery, which is 33.4% and 2.8% above that of LiMn₂O₄ and LiCoO₂, respectively. LiCoO₂ and LiMn₂O₄ have higher discharge voltage and better rate-capability than LiNi_0.45Co_0.10Mn_0.45O₂. All the three cathodes have excellent cycling performance with capacity retention of above 89.3% at the 250th cycle. Batteries with LiMn₂O₄ or LiNi_0.45Co_0.10Mn_0.45O₂ cathodes show better safety performance under abusive conditions than those with LiCoO₂ cathodes. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China; Project(2005037698) supported by the Postdoctoral Science Foundation of China     

Characterization of microstructure evolution and mechanical properties of the spray-deposited AZ31 magnesium alloy

The cylindrical billets of a Mg-3Al-1Zn (AZ31) alloy were synthesized by spray deposition processing. The microstruc-ture evolution and mechanical properties of the alloy were investigated. The results reveal that the microstructure of the AZ31 alloy is refined significantly by spray deposition processing. A homogeneous and equiaxial-grain structure with an average grain size of 17 μm is obtained. Further grain refinement with an average grain size of 5 μm is attributed to dynamic recrystallization during e...     

Effect of low temperature aging on microstructure and mechanical properties of super-high strength aluminum alloy

The effects of heat treatment on the microstructure and mechanical properties of two alloys, namely Al- 12.2%Zn-2.48%Cu-2.0%Mg-0.15%Zr-0. 166%Ag（alloy 1）, and Al-9.99%Zn-1.72%Cu-2.5%Mg-0.13%Zr（alloy 2） were investigated. The results show that low temperature aging after promotive solution treatment can increase elongation without the loss of strength for the studied alloys. The optimum aging treatment （T6） for alloy 1 and alloy 2 is 100 ℃/80 h and 100 ℃/48 h, respectively. Compared with other heat treatment alloys, alloy 1 and alloy 2 show super-high tensile strength up to 753 MPa and 788 MPa, remaining 9.3% and 9.7% elongation under T6 condition, respectively. During aging, trace addition of Ag enhances the formations of GP zone and metastable phase, and stabilizes GP zone and metastable phase to a higher temperature. Trace addition of Ag prolongs the aging time of reaching the peak strength and delays over-aging condition of the alloy. However, trace addition of Ag promotes the formation of coarse constituent in the alloy and consumes hardening alloying elements of Zn and Mg. Moreover, the addition of the transition element Zr in 7000 series super-high alloy forms incoherent Al3 Zr dispersoid which can serve as nucleation sites for nonuniform precipitation of η phase during aging process. The higher the aging temperature, the greater the tendency for nonuniform precipitation of η phase.     

Leaching kinetics of low grade zinc oxide ore in NH3-NH4Cl-H2O system

The leaching kinetics of low grade zinc oxide ore in NH3-NH4Cl-H2O system was studied. The effects of ore particle size, reaction temperature and the sum concentration of ammonium ion and ammonia on the leaching efficiency of zinc were examined. The leaching kinetics of low-grade zinc oxide ore in NH3-NH4Cl-H2O system follows the kinetic law of shrinking-core model. The results show that diffusion through the inert particle pores is the leaching kinetics rate controlling step. The calculated apparent activation energy of the process is about 7.057 kJ/mol. The leaching efficiency of zinc is 92.1% under the conditions of ore particle size of 69μm, holding at 80℃ for 60 min, sum ammonia concentration of 7.5 mol/L, the molar ratio of ammonium to ammonia being 2：1, and the ratio （g/mL） of solid to liquid being 1：10.     

Microstructure and Mechanical Properties of AZ31 Alloys Processed by Residual Heat Rolling

To produce high strength and ductility Mg alloys with high productivity and low energy consumption,the residual heat rolling (RHR) process was initially proposed.The microstucture and mechanical properties of AZ31 processed by RHR were investigated by optical micrscopy (OM),electron backscatter diffraction (EBSD),and electron universal testing machine.The yield strength (YS),ultimate tensile strength (UTS),and elongation to failure of RHRed AZ31 sheet were 194 MPa,311 MPa,and 22%,respectively.Th...     

Synthesis and characterization of Mg3(PO4)2-coated Li1.05Ni1/3Mn1/3Co1/3O2 cathode material for Li-ion battery

Mg₃(PO₄)₂-coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode materials were synthesized via co-precipitation method. The morphology, structure, electrochemical performance and thermal stability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), charge/discharge cycling and differential scanning calorimeter (DSC). SEM analysis shows that Mg₃(PO₄)₂-coating changes the morphologies of their particles and increases the grains size. XRD and CV results show that Mg₃(PO₄)₂-coating powder is homogeneous and has better layered structure than the bare one. Mg₃(PO₄)₂-coating improved high rate discharge capacity and cycle-life performance. The reason why the cycling performance of Mg₃(PO₄)₂-coated sample at 55 °C was better than that of room temperature was the increasing of lithium-ion diffusion rate and charge transfer rate with temperature rising. Mg₃(PO₄)₂-coating improved the cathode thermal stability, and the result was consistent with thermal abuse tests using Li-ion cells: the Mg₃(PO₄)₂ coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode did not exhibit thermal runaway with smoke and explosion, in contrast to the cells containing the bare Li_1.05Ni_1/3Mn_1/3Co_1/3O₂. Funded by the National Natural Science Foundation of China (No. 20273047)     

Effect of CaO doping on corrosion resistance of Cu/（NiFe2O4-10NiO） cermet inert anode for aluminum electrolysis

The CaO-doped Cu/（NiFe2O4-10NiO） cermet inert anodes were prepared by the cold isostatie pressing-sintering process, and their corrosion resistance to Na3AlF6-K3AlF6-Al203 melt was studied. The results show that the relative density of 5Cu/（NiFe2O4-10NiO） cermet sintered at 1 200 ℃ increases from 82.83% to 97.63% when 2% CaO （mass fraction） is added. During the electrolysis, the relative density of cermet inert anode descends owing to the chemical dissolution of additive CaO at ceramic grain boundary, which accelerates the penetration of electrolyte. Thus, the corrosion resistance to melts of Cu/（NiFe2O4-10NiO） cermet inert anode is reduced. To improve the corrosion resistance of the cermet inert anode, the content of CaO doped should be decreased and the technology of cleaning the ceramic grain boundary should be applied.     

Corrosion behavior of amorphous/nanocrystalline Al-Cr-Fe film deposited by double glow plasmas technique

In order to improve the corrosion resistance of AZ31 magnesium alloy, the amorphous/nanocrystal Al-Cr-Fe film has been successfully prepared on AZ31 magnesium alloy by double glow plasma technology. The amorphous/nanocrystalline consists of two different regions, i.e., an amorphous layer on outmost surface and an underlying lamellar nanocrystalline layer with a grain size of less than 10 nm. The corrosion behavior of amorphous/nanocrystalline Al-Cr-Fe film in 3.5% NaCl solution is investigated using an electrochemical polarization measurement. Compared with the AZ31 magnesium alloy, the amorphous/nanocrystalline Al-Cr-Fe film exhibits more positive corrosion potentials and lower corrosion current densities than that of AZ31 magnesium alloy. XPS measurement reveals that the passive film formed on the Al-Cr-Fe film after the anodic polarization tests is strongly enriched in Cr₂O₃, Fe₂O₃ and Al₂O₃ at outer surface of the film and in the inner layer consists of Cr₂O₃, FeO and Al₂O₃. Supported by the National Natural Science Foundation of China (Grant Nos. 50571045 and 50704022) and the Natural Science Foundation of Jiangsu Province, China (Grant No. BK2007591)     

Preparation and properties of 4.25Cu-0.75Ni／NiFe2O4 cermet

4.25Cu-0.75Ni/NiFe₂O₄ cermets were prepared by doping NiFe₂O₄ ceramic matrix with the mixed powders of Cu and Ni or Cu-Ni alloy powder as the electrical conducting metallic elements. The effects of technological parameters, such as the adding modes of metallic elements, the ball milling time, the sintering time and the sintering temperature, on the relative density and resistivity of the cermets were studied. The results show that the resistivity of 4.25Cu-0.75Ni/NiFe₂O₄ cermets decreases with increasing temperature, and has a turning point at 590 °C, which is similar to that of NiFe₂O₄ ceramic. The sintering temperature and adding modes of metallic elements have a great influence on the properties of 4.25Cu-0.75Ni/NiFe₂O₄ cermets. When the sintering temperature increases from 1200 °C to 1300 °C, the relative density increases from 89.86% to 95.33%, and the resistivity at 960 °C decreases from 0.11 Ω · cm to 0.03 Ω · cm, respectively. When the metallic elements are added with the mixed powders of Cu and Ni, the cermets of finely and uniformly dispersed metallic phase, high density and electric conductivity are obtained. The relative density and resistivity at 960 °C are 90.23% and 0.04 Ω · cm respectively for the cermet samples sintered at 1200 °C for 2 h, which are both better than those of the cermets prepared under the same technique conditions but with the metallic elements added as 85Cu-15Ni alloy powders. Foundation item: Project (G1999064903) supported by the National Key Fundamental Research and Development Program of China; project(2001AA335013) supported by the National High Technology Research and Development Program of China; project (50204014) supported by the National Natural Science Foundation of China     

Synthesis and sintering of Mg<Subscript>2</Subscript>Si thermoelectric generator by spark plasma sintering

Raw Mg,Si powder were used to fabricate Mg2Si bulk thermoelectric generator by spark plasma sintering （SPS）.The optimum parameters to synthesize pure Mg2Si powder were found to be 823 K,0 MPa,10 min with excessive content of 10wt% Mg from the stoichiometric Mg2Si.Mg2Si bulk was synthesized and densified simultaneously at low temperature （823 K） and high pressure （higher than 100 MPa） from the raw powder,but Mg,Si could not react completely,and the sample was not very dense with some microcracks on the surface.Then,Mg,Si powder reacted at 823 K,0 MPa,10 min in SPS chamber to form Mg2Si green compact,again sintered by SPS at 1023 K,20 MPa,5 min.The fabricated sample only contained Mg2Si phase with fully relative density.     

Influences of melt spinning on electrochemical hydrogen storage performance of nanocrystalline and amorphous Mg2Ni-type alloys

In order to improve the electrochemical hydrogen storage performance of the Mg₂Ni-type electrode alloys, Mg in the alloy was partially substituted by La, and the nanocrystalline and amorphous Mg₂Ni-type Mg_20−x La _x Ni₁₀ (x=0, 2) alloys were synthesized by melt-spinning technique. The microstructures of the as-spun alloys were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical hydrogen storage properties of the experimental alloys were tested. The results show that no amorphous phase is detected in the as-spun Mg₂₀Ni₁₀ alloy, but the as-spun Mg₁₈La₂Ni₁₀ alloy holds a major amorphous phase. As La content increases from 0 to 2, the maximum discharge capacity of the as-spun (20 m/s) alloys rises from 96.5 to 387.1 mA·h/g, and the capacity retaining rate (S ₂₀) at the 20th cycle grows from 31.3% to 71.7%. Melt-spinning engenders an impactful effect on the electrochemical hydrogen storage performances of the alloys. With the increase in the spinning rate from 0 to 30 m/s, the maximum discharge capacity increases from 30.3 to 135.5 mA·h/g for the Mg₂₀Ni₁₀ alloy, and from 197.2 to 406.5 mA·h/g for the Mg₁₈La₂Ni₁₀ alloy. The capacity retaining rate (S ₂₀) of the Mg₂₀Ni₁₀ alloy at the 20th cycle slightly falls from 36.7% to 27.1%, but it markedly mounts up from 37.3% to 78.3% for the Mg₁₈La₂Ni₁₀ alloy.     

Synthesis of γ-Al2O3 nanoparticles by chemical precipitation method

Highly pure active γ-Al₂O₃ nanoparticles were synthesized from aluminum nitrate and ammonium carbonate with a little surfactant by chemical precipitation method. The factors affecting the synthesis process were studied. The properties of γ-Al₂O₃ nanoparticles were characterized by DTA, XRD, BET, TEM, laser granularity analysis and impurity content analysis. The results show that the amorphous precursor Al(OH)₃ sols are produced by using 0.1 mol/L Al(NO₃)₃ · 9H₂O and 0.16 mol/L (NH₄)₂CO₃ · H₂O reaction solutions, according to the volume ratio 1.33, adding 0.024% (volume fraction) surfactant PEG600, and reacting at 40 °C, 1 000 r/min stirring rate for 15 min. Then, after stabilizing for 24 h, the precursors were extracted and filtrated by vacuum, washed thoroughly with deionized water and dehydrated ethanol, dried in vacuum at 80°C for 8 h, final calcined at 800 °C for 1 h in the air, and high purity active γ-Al₂O₃ nanoparticles can be prepared with cubic in crystal system, O _H ⁷ -FD3M in space group, about 9 nm in crystal grain size, about 20 nm in particle size and uniform size distribution, 131. 35 m²/g in BET specific surface area, 7 – 11 nm in pore diameter, and not lower than 99.93% in purity. Foundation item: Project(03JJY3015) supported by the Natural Science Foundation of Hunan Province     

Synthesis and characterization of high-voltage cathode material LiNi0.5Mn1.5O4 by one-step solid-state reaction

LiNi_0.5Mn_1.5O₄ was prepared under various conditions by one-step solid-state reaction in air and its properties were investigated by X-ray diffractormetry (XRD), scanning electron microscopy (SEM) and electrochemical measurement. XRD patterns show that LiNi_0.5Mn_1.5O₄ synthesized under various conditions has cubic spinel structure. SEM images exhibit that the particle size increases with increasing calcination temperature and time. Electrochemical test shows that the LiNi_0.5Mn_1.5O₄ calcined at 700 °C for 24 h delivers up to 143 mA · h/g, and the capacity retains 132 mA · h/g after 30 cycles. Foundation item: Project (76600) supported by Postdoctoral Science Foundation of Central South University