ZnO thin films prepared by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on soda lime glass substrates by pulsed laser deposition (PLD) in an oxygen-reactive atmosphere. The structural, optical, and electrical properties of the as-prepared thin films were studied in dependence of substrate temperature and oxygen pressure. High quality polycrystalline ZnO films with hexagonal wurtzite structure were deposited at substrate temperatures of 100 and 300 °C. The RMS roughness of the deposited oxide films was found to be in the range 2-9 nm and was only slightly dependent on substrate temperature and oxygen pressure. Electrical measurements indicated a decrease of film resistivity with the increase of substrate temperature and the decrease of oxygen pressure. The ZnO films exhibited high transmittance of 90% and their energy band gap and thickness were in the range 3.26-3.30 eV and 256-627 nm, respectively.     

Structural and magnetic properties of Co-Ga co-doped ZnO thin films fabricated by pulsed laser deposition

Co-Ga co-doped ZnO films were fabricated by pulsed laser deposition on quartz substrates. The obtained films exhibited a wurtzite structure with c-axes growth preference. Optical measurements showed the presence of the cobalt ions in a tetrahedral crystal field, which proved that the Co ion substitution in the ZnO lattice, acting as magnetic cation. Hall measurements indicated that the films were n-type conductive with the electron concentrations of ~ 10²⁰/cm³. This value was much higher than that of the Co-doped films, suggesting the effective incorporation of Ga in the films. Room temperature ferromagnetism was observed for the Ga-Co co-doped thin films.     

Microstructure and magnetic properties of zinc ferrite thin films produced by pulsed laser deposition

Zinc ferrite thin films were deposited from a target of zinc ferrite onto a MgO substrate using XeCl excimer laser operating at 308 nm and frequency of 30 Hz. The crystallographic characterizations of the films were performed using X-ray diffraction (XRD). Microstructure, surface morphology, chemical composition and grain size, as well as surface roughness were obtained from scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and atomic force microscopy (AFM). The magnetic properties of the thin films were studied in the temperature range 5–300 K and in fields of up to 5 T using SQUID magnetometry. Data on temperature and field dependence of magnetization provide a strong evidence for superparamagnetism. Paper presented at 8 AGM of MRSI, BARC, Mumbai, 1997.     

Morphological, structural and optical properties of thin SiC layer growth onto silicon by pulsed laser deposition

Crystalline silicon carbide thin layers were grown on a p-type Si(1 0 0) substrate by pulsed laser deposition (PLD) using KrF excimer laser at λ=248 nm from a 6H-SiC hot-pressed target. The target “SiC” used to elaborate our SiC films is realized from a mixture of 1SiO₂ with 3C (carbon) “1SiO₂+3C” heated in an oven at 2500 °C (the target was a hot-pressed material and supplied by Goodfellow). The morphological, structural and optical properties of SiC layers were investigated by scanning electronic microscopy (SEM), high-resolution X-ray diffraction (XRD), secondary ion mass spectrometry (SIMS) and UV-visible spectrophotometer. XRD analysis of the target showed that this latter is a hexagonal structure (6H-SiC). The XRD pattern shows that a 1.6 μm crystalline SiC layer was formed. In addition, a SIMS analysis gives a ratio Si/C of the thin SiC layer around 1.15 but the ratio Si/C of the target was found equal to 1.06, whereas one should have 1.0. This is due to the degree of the sensitivity of the SIMS technique and due to the higher ionization efficiency of Si compared to C atoms, all these which give different ratios. It is known that the PLD technique reproduces the same macroscopic property (optical, mechanical, structural, etc.) of the target. An optical gap (E_Gap) of the SiC layer of about 2.51 eV was obtained by reflectance measurement. Finally, a crystalline thin SiC layer of 1.6 μm was elaborated using PLD method at low-temperature deposition.     

Structural and optical properties of tellurite thin film glasses deposited by pulsed laser deposition

Tellurite (TeO₂-TiO₂-Nb₂O₅) thin film glasses have been produced by pulsed laser deposition at room temperature at laser energy densities in the range of 0.8-1.5 J/cm² and oxygen pressures in the range of 3-11 Pa. The oxygen concentration in the films increases with laser energy density to reach values very close to that of the bulk glass at 1.5 J/cm², while films prepared at 1.5 J/cm² and pressures above 5 Pa show oxygen concentration in excess of 10% comparing to the glass. X-ray photoelectron spectroscopy shows the presence of elementary Te in films deposited at O₂ pressures ≤ 5 Pa that is not detected at higher pressures, while analysis of Raman spectra of the samples suggests a progressive substitution of TeO₃ trigonal pyramids by TeO₄ trigonal bipyramids in the films when increasing their oxygen content. Spectroscopic ellipsometry analysis combined with Cauchy and effective medium modeling demonstrates the influence of these compositional and structural modifications on the optical response of the films. Since the oxygen content determines their optical response through the structural modifications induced in the films, those can be effectively controlled by tuning the deposition conditions, and films having large n (2.08) and reduced k (< 10^− 4) at 1.5 μm have been produced using the optimum deposition conditions.     

Structural and optical properties of neodymium-doped lutetium fluoride thin films grown by pulsed laser deposition

Neodymium-doped lutetium fluoride (Nd³⁺:LuF₃) thin films were successfully grown on MgF₂ (0 0 1) substrates by pulsed laser deposition (PLD). It is void of cracks that are otherwise prevalent due to structural phase transitions in Nd³⁺:LuF₃ during thin film deposition and bulk crystal growth. Cathodoluminescence (CL) spectra revealed multiple emission peaks, with a dominant peak in the vacuum ultraviolet (VUV) region at 179 nm. This peak has a decay time of 6.7 ns. The ability to grow high quality Nd³⁺-doped fluoride thin films would enable fabrication of VUV light-emitting devices that will enhance applications requiring efficient VUV light sources.     

InGaZnO thin films grown by pulsed laser deposition

We fabricated InGaZnO (IGZO) ceramic target (In: Ga: Zn = 1: 1: 4 in atomic ratio) using solid-state reaction at ambient atmosphere, and deposited IGZO thin films on quartz glass at room temperature under various oxygen partial pressures using the pulsed laser deposition method. Influence of oxygen pressure on crystal structure, surface morphology, optical and electrical properties were investigated. It was found that all the films deposited at room temperature exhibit amorphous structure. On the other hand, the physical properties of the films like transparency, electron mobility, and free-electron concentration were found to be correlated to the oxygen pressure during the deposition and in turn to the possible oxygen vacancies or metallic interstitials in the films. The analysis of X-ray photoelectron spectra (XPS) of the films indicated that there are no metallic 3d states of In, Ga and Zn, suggesting that oxygen vacancies could be main defects that affect physical properties of the films.     

ITO thin films deposited by advanced pulsed laser deposition

Indium tin oxide thin films were deposited by computer assisted advanced PLD method in order to obtain transparent, conductive and homogeneous films on a large area. The films were deposited on glass substrates. We studied the influence of the temperature (room temperature (RT)-180 °C), pressure (1-6 × 10^− 2 Torr), laser fluence (1-4 J/cm²) and wavelength (266-355 nm) on the film properties. The deposition rate, roughness, film structure, optical transmission, electrical conductivity measurements were done. We deposited uniform ITO thin films (thickness 100-600 nm, roughness 5-10 nm) between RT and 180 °C on a large area (5 × 5 cm²). The films have electrical resistivity of 8 × 10^− 4 Ω cm at RT, 5 × 10^− 4 Ω cm at 180 °C and an optical transmission in the visible range, around 89%.     

Growth process observation of homoepitaxial ZnO thin films using optical emission spectra during pulsed laser deposition

Homoepitaxial ZnO thin films were prepared on the Zn-polar or O-polar ZnO substrates by pulsed laser deposition method. Optical emission spectroscopy of the plume was carried out to estimate O/Zn flux ratio under the various deposition conditions such as oxygen pressure, laser fluence, and the distance between target and substrate. It is revealed that the O/Zn flux ratio could be controlled by laser fluence, oxygen pressure, and target-substrate distance. Zn-rich O/Zn flux promotes pit formation and O-rich flux yields the three-dimensional growth. The difference of the growth process on Zn-polar or O-polar substrates is also discussed.     

Surface morphology of AlN films synthesized by pulsed laser deposition

Surface morphology of AlN films, synthesized on Si substrates by pulsed laser deposition, has been examined by recording atomic-force-microscopy (AFM) images. The influence of N₂ ambient pressure, ranging from 5 × 10⁻⁴ Pa to 10 Pa, is reflected well in the alteration of the surface roughness and size of crystallites of the AlN films. A tendency of a decrease in the surface roughness with increasing N₂ pressure was observed, which also correlates with the polycrystalline structure of the films. Deposition in vacuum resulted in the highest surface roughness due to the large size of crystallites emerging from the surface, while increasing the nitrogen pressure yielded smaller crystallites and a smoother film surface. The presented results could be useful for applications of pulsed laser deposited AlN in different optical and acoustic devices, where the crystalline quality of the AlN films and the surface is very important.     

Low-temperature deposition of iridium thin films by pulsed laser deposition

Extremely smooth iridium (Ir) thin films were deposited on Si(1 0 0) substrate at lower temperature than 300 °C by pulsed laser deposition (PLD) technique using Ir target in a vacuum atmosphere. The crystal orientation, surface morphology, and resistivity of the Ir thin films were systematically determined as a function of substrate temperature. Well-crystallized and single-phase Ir thin films with (1 1 1) preferred orientation were obtained at substrate temperature of 200-300 °C. The surface roughness increased with the increasing of substrate temperature. Likewise, the room-temperature resistivity of Ir thin films decreased with increasing substrate temperature, showing a low value of (10.7±0.1) μΩ cm at 300 °C.     

A study of microstructural and optical properties of nanocrystalline ceria thin films prepared by pulsed laser deposition

Thin films of cerium oxide (CeO₂) have been deposited on (100) Si substrates using pulsed laser deposition technique at various substrate temperatures from room temperature (RT) to 973 K at an optimized oxygen partial pressure of 3 Pa. Structural, morphological and optical properties have been carried out using X-ray diffraction (XRD), Raman, ellipsometry and atomic force microscopy techniques. XRD results showed that the deposited films are polycrystalline with cubic structure. At room temperature, the film showed preferred orientation along (111) plane, while at higher temperatures, it exhibited preferred orientation along (200). The crystallite sizes were calculated and were found to be in the range 17-52 nm. The texture coefficient for (200) reflection increased until 573 K, and then decreased in the temperature range 673-973 K. The Raman peak appeared at 463 cm^− 1 due to the F_2g active mode also confirmed the formation of CeO₂ with a cubic structure. There was a systematic variation in the Raman peak intensity, frequency shift and line broadening with the increase of temperature. The ellipsometry studies showed that the refractive index and band gap increased from 2.2 to 2.6 and 3.4 to 3.6 eV, respectively with increasing substrate temperature from RT to 973 K.     

Production of porous carbon thin films by pulsed laser deposition

Pulsed laser deposition (PLD) has been used together with the Glancing Angle Deposition (GLAD) technique [1 and 2] for the first time to produce highly porous structured films. A laser produced carbon plasma and vapour plume was deposited at a highly oblique incident angle onto rotating Si substrates, resulting in films exhibiting high bulk porosity and controlled columnar microstructure. By varying the substrate rotation rate, the shape of the microcolumns can be tailored. These results extend the versatility of the GLAD process to materials not readily deposited by means of traditional physical vapour deposition techniques.     

Chiral organic thin films: How far pulsed laser deposition can conserve chirality

We have investigated the pulsed laser deposition (PLD) technique to grow isotropic thin films based on bridged binaphthyls. We have focused on the conservation of the chiroptical properties during the deposition process. Chiral high purity liquid chromatography reveals that all the molecules are damaged at the same laser power threshold, but that below this threshold, neither bridged binaphthyl nor binaphthol undergo racemization. In situ circular dichroism spectra, as well as optical rotation (OR) measurements, confirm these findings. Isotropic 2 μm thick films with OR of 20°/mm at 546 nm were deposited. Furthermore, an estimation of the thermal load reveals that, due to its instantaneous nature, PLD does not induce thermal degradation. Only photochemical processes are involved in both racemization and degradation.     

Spatial spectral evolution in pulsed laser deposited lead-germanate thin films by micro-infrared spectroscopy

Lead-germanate thin films were developed on silicon substrates by pulsed laser deposition from bulk glassy targets of composition 0.4PbO-0.6GeO₂, and micro-infrared transmittance measurements were performed to assess the state of the grown films. Measurements across the radius of films revealed surprisingly large spectral changes, reminiscent of lead-oxide variations in corresponding bulk glasses. To search for the origin of this effect, the infrared spectra were simulated by employing the rigorous expression for the transmittance of a bilayer system to take into full account multiple internal reflections in both thin film and substrate. The results showed that the profiles of the experimental spectra can be accurately described by using as input the complex refractive index of the target glassy material and by considering film thickness variations from the center to the edges of the film. This work demonstrates the strong influence of optical effects on the infrared spectra of thin films, and manifests also the effectiveness of infrared spectroscopy when coupled with rigorous calculations to characterize the structure of thin films.     

A parametric study of AlN thin films grown by pulsed laser deposition

High quality AlN thin films were grown at 200–450°C on sapphire substrates by laser ablation of Al targets in nitrogen reactive atmosphere. The nitrogen pressure was varied between 10⁻³ and 10⁻¹ mbar. The reactive gas pressure during irradiation and the temperature of the substrate were found to essentially influence the quality of the layers. X-ray diffraction analysis evidenced the formation of highly orientated layers for a very restrictive set of parameters. Other analysis techniques, like X-ray photoelectron spectroscopy, secondary ion mass spectroscopy, optical transmission spectroscopy have been used to evidence the good stoichiometry and purity of the films. The characteristics of these films were compared with those of AlN thin films deposited in similar experimental conditions, on Si (100) and Si (111) substrates.     

Metal-semiconductor transition in Nb-doped ZnO thin films prepared by pulsed laser deposition

The structural, electrical and optical properties of Nb-doped ZnO films were investigated with different Nb contents (0, 0.15, 0.31, 0.46, 0.62, and 0.94 at.%) in this article. The film with 0.46 at.% Nb content showed the lowest resistivity of 8.95 × 10^− 4 Ω cm and high transmittance about 80% with high c-axis orientation. The undoped ZnO film showed a semiconducting behavior. And Nb-doped ZnO films showed a metal-semiconductor transition (MST), which was connected with localization of degenerate electrons. The films showed metallic conductivity at temperatures closer to the ambient temperature and semiconducting behavior at lower temperatures. It was noted that the NZO films with much lower Nb concentration of 0.15 at.% presented MST compared with other transparent conducting oxides films.     

Composition, structural and electrical properties of thin films prepared by laser ablation of neodymium-doped potassium gadolinium tungstate

Thin films were grown on (001) SiO₂, SiO₂/(100) Si or (100) MgO substrates by laser ablation of neodymium-doped potassium gadolinium tungstate (Nd:KGW) single crystal target. The films were deposited at temperatures between room temperature and 750 °C and pressures between 1 × 10^− 4 Pa and 50 Pa of oxygen ambient. The influence of the deposition conditions on the composition, structure, morphology and electrical properties of the films was investigated. Special attention was paid to the films deposited in vacuum (1 × 10^− 4 Pa) or at very low oxygen pressures. Under such conditions, the potassium (K), gadolinium (Gd) and oxygen (O) content decreased strongly as the temperature was increased. At room temperature, the films were K and O stoichiometric, in contrast with Gd, which showed a concentration twice higher. The films were polycrystalline, with the exception of those deposited at temperatures below 500 °C, which were amorphous. However, all were smooth and dense. The films grown in vacuum and at temperatures between 500 and 700 °C consist mainly of “â-tungsten” - tungsten oxide (W₃O) phase. The films grown on SiO₂/Si possessed the best surface quality with nano-size relief. The resistivity measurements as a function of the temperature showed that the films produced in vacuum and at temperatures below 500 °C were highly insulating, whereas at 600 °C they exhibited semiconducting behavior or a metallic one at 700 °C. This behavior can be attributed to the existence of various valence states for tungsten below W⁶⁺ in the films and to their crystal structure.     

Preparation of the hard CNx thin films using NO ambient gas by pulsed laser deposition

Pulsed laser deposition (PLD) technique has been widely used in thin film preparation because of its wonderful and excellent properties and amorphous carbon nitride (CN_x) thin films are recognized to have potential for applications like hard coating and electron field emission device. We have deposited CN_x thin films by KrF excimer laser – (λ= 248 nm) ablation of pure graphite target in pure NO gas ambient condition. In this paper, we have prepared the CN_x thin films at various ambient NO gas pressure of 1.3–26 Pa and laser fluence of 2– 5J cm^?2 on Si (100) substrate. We consider that the hardness of CN_x thin films improves due to the increase the nitrogen/carbon (N/C) ratio. The N/C ratio depended on the ambient NO gas pressure and laser fluence. We obtainedthe maximum N/C ratio of 1.0 at NO 3.3 Pa. The typical absorption of CN bonds such as sp² C–N, sp³ C–N, G band and D band were detected from the infrared absorption measurement by FTIR in the deposited CN_x thin films.     

Large nonlinear optical response of a Bi1.5Zn1.0Nb1.5O7 thin film fabricated by pulsed laser deposition

The Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin film has been fabricated on MgO (001) substrate by pulsed laser deposition. The nonlinear optical properties of the BZN film were investigated using Z-scan technique at a wavelength of 532 nm with 25 ps pulse duration. The two-photon absorption coefficient and the nonlinear refractive index of the BZN film were obtained to be 4.2 × 10^− 6 cm/W and 1.6 × 10^− 10 cm²/W respectively, which are comparable with those of some representative nonlinear optical materials. The large and fast response optical nonlinearities indicated that the BZN film is a promising candidate for future photonics devices.