Effect of annealing on molybdenum doped indium oxide thin films RF sputtered at room temperature

Thin films of molybdenum doped indium oxide (IMO) were deposited on glass at room temperature using an in-built three-source RF magnetron sputtering. The films were studied as a function of oxygen volume percentage (O₂ vol. %; ranging from 0.0 to 17.5%) in the sputtering chamber. The as-deposited amorphous films were crystallized on post-annealing. The as-deposited films are low conducting and Hall coefficients were undetectable; whereas post-annealed films possess fairly high conductivity. The lowest transmittance (11.96% at 600 nm) observed from the films deposited without oxygen increased to a maximum of 88.01% (3.5 O₂ vol. %); whereas this transmittance was decreased with the increasing O₂ vol. % to as low as 81.04% (15.6 O₂ vol. %); a maximum of 89.80% was obtained from the films annealed at 500 °C in open air (3.5 O₂ vol. %). The optical band gap of 3.80 eV obtained from the films deposited without oxygen increased with increasing O₂ vol. % to as high as 3.91 eV (17.5 O₂ vol. %). A maximum of 3.92 eV was obtained from the films annealed at 300 °C in N₂:H₂ gas atmosphere (17.5 O₂ vol. %).     

Effect of the oxygen partial pressure on the microstructure and optical properties of ZnO:Cu films

Cu-doped zinc oxide (ZnO:Cu) films were deposited on Si substrates using radio frequency reactive magnetron sputtering at different oxygen partial pressures. The effect of oxygen partial pressure on the microstructures and optical properties of ZnO:Cu thin films were systematically investigated by X-ray diffraction (XRD), atomic force microscopy (AFM) and fluorescence spectrophotometer. The results indicated that the grain orientation of the films was promoted by appropriate oxygen partial pressures. And with increasing oxygen partial pressure, the compressive stress of the films increased first and then decreased. The photoluminescence (PL) of the samples were measured at room temperature. A violet peak, two blue peaks and a green peak were observed from the PL spectra of the four samples. The origin of these emissions was discussed and the mechanism of violet emission of ZnO:Cu thin films were suggested.     

Preliminary studies on molybdenum-doped indium oxide thin films deposited by radio-frequency magnetron sputtering at room temperature

Thin films of molybdenum-doped indium oxide (IMO) were prepared by a 3-source, cylindrical radio-frequency magnetron sputtering at room temperature. The films were post-annealed and were characterized by their structural (X-ray diffraction) and optical (UV-VIS-NIR spectrophotometer) properties. The films were studied as a function of oxygen volume percentage (O₂ vol.%) ranging from 3.5 to 17.5. The structural studies revealed that the as-deposited amorphous films become crystalline on annealing. In most cases, the (222) reflection emerged as high intensive peak. The poor visible transmittance of the films as-deposited without oxygen was increased from ∼ 12% to over 80% on introducing oxygen (3.5 O₂ vol.%). For the films annealed in open air, the average visible transmittance in the wavelength ranging 400-800 nm was varied between 77 and 84%. The films annealed at high temperatures (> 300 °C) decreased the transmittance to as low as < 1%. The optical band gap of the as-deposited films increased from the range 3.83-3.90 to 3.85-3.98 eV on annealing at different conditions.     

Effect of oxygen partial pressure on microstructural and optical properties of titanium oxide thin films prepared by pulsed laser deposition

Nanocrystalline titanium oxide (TiO₂) thin films were deposited on silicon (1 0 0) and quartz substrates at various oxygen partial pressures (1 × 10⁻⁵ to 3.5 × 10⁻¹ mbar) with a substrate temperature of 973 K by pulsed laser deposition. The microstructural and optical properties were characterized using Grazing incidence X-ray diffraction, atomic force microscopy, UV–visible spectroscopy and photoluminescence. The X-ray diffraction studies indicated the formation of mixed phases (anatase and rutile) at higher oxygen partial pressures (3.5 × 10⁻² to 3.5 × 10⁻¹ mbar) and strong rutile phase at lower oxygen partial pressures (1 × 10⁻⁵ to 3.5 × 10⁻³ mbar). The atomic force microscopy studies showed the dense and uniform distribution of nanocrystallites. The root mean square surface roughness of the films increased with increasing oxygen partial pressures. The UV–visible studies showed that the bandgap of the films increased from 3.20 eV to 3.60 eV with the increase of oxygen partial pressures. The refractive index was found to decrease from 2.73 to 2.06 (at 550 nm) as the oxygen partial pressure increased from 1.5 × 10⁻⁴ mbar to 3.5 × 10⁻¹ mbar. The photoluminescence peaks were fitted to Gaussian function and the bandgap was found to be in the range ∼3.28–3.40 eV for anatase and 2.98–3.13 eV for rutile phases with increasing oxygen partial pressure from 1 × 10⁻⁵ to 3.5 × 10⁻¹ mbar.     

Optical properties of amorphous-like indium zinc oxide and indium gallium zinc oxide thin films

The paper presents the optical properties of amorphous-like indium zinc oxide and indium gallium zinc oxide thin films with various In/(In + Zn) ratios obtained by Pulsed Laser Deposition. Thickness results obtained from simulations of X-ray Reflectivity and Spectroscopic Ellipsometry data were very similar. The dependence of density on stoichiometry resembles the corresponding dependence of the refractive index in the transparency range. A free carrier absorption was noted in the visible spectral range, leading to a weak absorbing thin transparent conductive oxide. On the other hand, the refractive index is smaller than those of based oxides (ZnO and In₂O₃), and counterbalance therefore the weak light absorption.     

Nanostructured thin films of indium oxide nanocrystals confined in alumina matrixes

Nanocrystals of indium oxide (In₂O₃) with sizes below 10 nm were prepared in alumina matrixes by using a co-pulverization method. The used substrates such as borosilicate glasses or (100) silicon as well as the substrate temperatures during the deposition process were modified and their effects characterized on the structural and physical properties of alumina-In₂O₃ films. Complementary investigation methods including X-ray diffraction, optical transmittance in the range 250-1100 nm and transmission electron microscopy were used to analyze the nanostructured films. The crystalline order, morphology and optical responses were monitored as function of the deposition parameters and the post-synthesis annealing. The optimal conditions were found and allow realizing suitable nanostructured films with a major crystalline order of cubic phase for the In₂O₃ nanocrystals. The optical properties of the films were analyzed and the key parameters such as direct and indirect band gaps were evaluated as function of the synthesis conditions and the crystalline quality of the films.     

Modeling the optical properties of tin oxide thin films

Searching the many papers reporting on the optical characteristics of tin oxide thin films, an obvious question arises: what is the origin of the very large differences in the reported optical and electrical properties of these films? The objective of the present work is to resolve this question by applying a modeling approach, simulating the refractive index of SnO, SnO₂, SnO + SnO₂, and porous tin oxide films in the visible range of the spectrum under various structure and composition conditions. Using the semi-empirical model of Wemple and DiDomenico for the dielectric function below the interband absorption edge of ionic and covalent solids, and the effective-medium theory of Bruggeman, the refractive indices of SnO, SnO₂, several mixtures of SnO and SnO₂ and various porous tin oxide films were calculated. The resulting data are compared with some published data to suggest the compositional and structural characteristics of the reported oxides. The correlation between the optical properties of the studied thin films and film composition is also indicated. It is proposed that the large spread in reported optical data is possibly a spread in the composition of the samples.     

Thickness dependence of structural and optical properties of indium tin oxide nanofiber thin films prepared by electron beam evaporation onto quartz substrates

Indium tin oxide (ITO) thin films, produced by electron beam evaporation technique onto quartz substrates maintained at room temperature, are grown as nanofibers. The dependence of structural and optical properties of ITO thin films on the film thickness (99-662 nm) has been reported. The crystal structure and morphology of the films are investigated by X-ray diffraction and scanning electron microscope techniques, respectively. The particle size is found to increase with increasing film thickness without changing the preferred orientation along (2 2 2) direction. The optical properties of the films are investigated in terms of the measurements of the transmittance and reflectance determined at the normal incidence of the light in the wavelength range (250-2500 nm). The absorption coefficient and refractive index are calculated and the related optical parameters are evaluated. The optical band gap is found to decrease with the increase of the film thickness, whereas the refractive index is found to increase. The optical dielectric constant and the ratio of the free carrier concentration to its effective mass are estimated for the films.     

Deposition by magnetron sputtering and characterization of indium tin oxide thin films

In this work the properties of indium tin oxide (ITO) films deposed on glass substrates by magnetron sputtering technique in the temperature range below 200 °C are studied by various methods. The physical properties of ITO thin films have been investigated using optical transmittance, photoluminescence, atomic force microscopy, ellipsometry, Hall-effect and four point probe methods. It is established that properties of ITO layers depend drastically on the temperature and oxygen partial pressure during the deposition process and exhibit some peculiarities of the surface morphology. It is found that the band gap energy of this material varies in the energy range from 4.1 to 4.4 eV and depends on the growth conditions. It is suggested that local deviations from the stoichiometry and defects are the main physical reasons of Burstein-Moss shift of the optical band gap.     

Characterization of nanocrystalline indium tin oxide thin films prepared by ion beam sputter deposition method

Indium tin oxide (ITO) thin films were deposited on glass substrates by ion beam sputter deposition method in three different deposition conditions [(i) oxygen (O₂) flow rate varied from 0.05 to 0.20 sccm at a fixed argon (1.65 sccm) flow rate, (ii) Ar flow rate changed from 1.00 to 1.65 sccm at a fixed O₂ (0.05 sccm) flow rate, and (iii) the variable parameter was the deposition time at fixed Ar (1.65 sccm) and O₂ (0.05 sccm) flow rates]. (i) The X-ray diffraction (XRD) patterns show that the ITO films have a preferred orientation along (400) plane; the orientation of ITO film changes from (400) to (222) direction as the O₂ flow rate is increased from 0.05 to 0.20 sccm. The optical transmittance in the visible region increases with increasing O₂ flow rate. The sheet resistance (R_s) of ITO films also increases with increasing O₂ flow rate; it is attributed to the decrease of oxygen vacancies in the ITO film. (ii) The XRD patterns show that the ITO film has a strong preferred orientation along (222) direction. The optical transmittance in the visible spectral region increases with an increase in Ar flow rate. The R_s of ITO films increases with increasing Ar flow rate; it is attributed to the decrease of grain size in the films. (iii) A change in the preferred orientations of ITO films from (400) to (222) was observed with increasing film thickness from 314 to 661 nm. The optical transmittance in the visible spectral region increases after annealing at 200 °C. The R_s of ITO film decreases with the increase of film thickness.     

Effect of annealing temperature on structural, electrical and optical properties of B-N codoped ZnO thin films

The B-N codoped p-type ZnO thin films have been prepared by radio frequency magnetron sputtering using a mixture of nitrogen and oxygen as sputtering gas. The effect of annealing temperature on the structural, electrical and optical properties of B-N codoped films was investigated by using X-ray diffraction, Hall-effect, photoluminescence and optical transmission measurements. Results indicated that the electrical properties of the films were extremely sensitive to the annealing temperature and the conduction type could be changed dramatically from n-type to p-type, and finally changed to weak p-type in a range from 600 °C to 800 °C. The B-N codoped p-type ZnO film with good structural, electrical and optical properties can be obtained at an intermediate annealing temperature region (e.g., 650 °C). The codoped p-type ZnO had the lowest resistivity of 2.3 Ω cm, Hall mobility of 11 cm²/Vs and carrier concentration of 1.2 × 10¹⁷ cm^− 3.     

Structural and electrical properties of sputtered indium-zinc oxide thin films

In this study, indium-zinc oxide (IZO) thin films have been prepared at a room temperature, 200 and 300 °C by radio frequency magnetron sputtering from a In₂O₃-12 wt.% ZnO sintered ceramic target, and their dependence of electrical and structural properties on the oxygen content in sputter gas, the substrate temperature and the post-heat treatment was investigated. X-ray diffraction measurements showed that amorphous IZO films were formed at room temperature (RT) regardless of oxygen content in sputter gas, and micro-crystalline and In₂O₃-oriented crystalline films were obtained at 200 and 300 °C, respectively. From the analysis on the electrical and the structural properties of annealed IZO films under Ar atmosphere at 200, 300, 400 and 500 °C, it was shown that oxygen content in sputter gas is a critical parameter that determines the local structure of amorphous IZO film, stability of amorphous phase as well as its eventual crystalline structure, which again decide the electrical properties of the IZO films. As-prepared amorphous IZO film deposited at RT gave specific resistivity as low as 4.48 × 10^− 4 Ω cm, and the highest mobility value amounting to 47 cm²/V s was obtained from amorphous IZO film which was deposited in 0.5% oxygen content in sputter gas and subsequently annealed at 400 °C in Ar atmosphere.     

Effect of alumina doping on structural, electrical, and optical properties of sputtered ZnO thin films

A systematic study of the influence of alumina (Al₂O₃) doping on the optical, electrical, and structural characteristics of sputtered ZnO thin films is reported in this study. The ZnO thin films were prepared on 1737F Corning glass substrates by R.F. magnetron sputtering from a ZnO target mixed with Al₂O₃ of 0-4 wt.%. X-ray diffraction (XRD) analysis demonstrates that the ZnO thin films with Al₂O₃ of 0-4 wt.% have a highly (002) preferred orientation with only one intense diffraction peak with a full width at half maximum (FWHM) less than 0.5°. The electrical properties of the Al₂O₃-doped ZnO thin films appear to be strongly dependent on the Al₂O₃ concentration. The resistivity of the films decreases from 74 Ω·cm to 2.2 × 10^− 3 Ω·cm as the Al₂O₃ content increases from 0 to 4 wt.%. The optical transmittance of the Al₂O₃-doped ZnO thin films is studied as a function of wavelength in the range 200-800 nm. It exhibits high transparency in the visible-NIR wavelength region with some interference fringes and sharp ultraviolet absorption edges. The optical bandgap of the Al₂O₃-doped ZnO thin films show a short-wavelength shift with increasing of Al₂O₃ content.     

Morphological, optical and electrical properties of samarium oxide thin films

We present here results on samarium oxide thin films, obtained by pulsed laser deposition and by radio frequency assisted pulsed laser deposition. Three different substrate types were used: silicon, platinum covered silicon and titanium covered silicon. The influence of the deposition parameters (oxygen pressure and laser fluence) on the structure and morphology of the thin films was studied. The substrate-thin film interface zone was investigated; the optical and electrical properties (the losses, dielectric constant and leakage currents) were also determined.     

Effect of annealing treatment on structural, electrical, and optical properties of Ga-doped ZnO thin films deposited by RF magnetron sputtering

The effect of annealing on structural, electrical, and optical properties of Ga-doped ZnO (GZO) films prepared by RF magnetron sputtering was investigated in air and nitrogen. GZO films are polycrystalline with a preferred 002 orientation. The resistivities of annealed films are larger than the as-deposited. The transmittance in the near IR region increases greatly and the optical band gap decreases after annealing. The photoluminescence spectra is composed of a near band edge emission and several deep level emissions (DLE) which are dominated by a blue emission. After annealing, these DLEs are enhanced evidently.     

Effect of cadmium oxide incorporation on the microstructural and optical properties of pulsed laser deposited nanostructured zinc oxide thin films

CdO doped (doping concentration 0, 1, 3 and 16 wt%) ZnO nanostructured thin films are grown on quartz substrate by pulsed laser deposition and the films are annealed at temperature 500 °C. The structural, morphological and optical properties of the annealed films are systematically studied using grazing incidence X-ray diffraction (GIXRD), energy dispersive X-ray analysis (EDX), scanning electron microscopy (SEM), atomic force microscopy (AFM), Micro-Raman spectra, UV–vis spectroscopy, photoluminescence spectra and open aperture z-scan. 1 wt% CdO doped ZnO films are annealed at different temperatures viz., 300, 400, 500, 600, 700 and 800 °C and the structural and optical properties of these films are also investigated. The XRD patterns suggest a hexagonal wurtzite structure for the films. The crystallite size, lattice constants, stress and lattice strain in the films are calculated. The presence of high-frequency E₂ mode and the longitudinal optical A₁ (LO) modes in the Raman spectra confirms the hexagonal wurtzite structure for the films. The presence of CdO in the doped films is confirmed from the EDX spectrum. SEM and AFM micrographs show that the films are uniform and the crystallites are in the nano-dimension. AFM picture suggests a porous network structure for 3% CdO doped film. The porosity and refractive indices of the films are calculated from the transmittance and reflectance spectra. Optical band gap energy is found to decrease in the CdO doped films as the CdO doping concentration increases. The PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. The 16CdZnO film shows an intense deep green PL emission. Non-linear optical measurements using the z-scan technique indicate that the saturable absorption (SA) behavior exhibited by undoped ZnO under green light excitation (532 nm) can be changed to reverse saturable absorption (RSA) with CdO doping. From numerical simulations the saturation intensity (I_s) and the effective two-photon absorption coefficient (β) are calculated for the undoped and CdO doped ZnO films.     

Growth, structure and properties of sputtered niobium oxide thin films

Niobium oxide (NbO_x) films were deposited by pulsed dc magnetron sputtering at different total gas pressures and oxygen flow rates. Various film properties were characterized by X-ray photoelectron spectroscopy, atomic force microscopy, variable angle spectroscopic ellipsometry and four point probe. It was found that oxygen flow rates required for preparing NbO, NbO₂ and Nb₂O₅ at a constant total pressure of 0.93 Pa were approximately 2, 4 and > 6 sccm, respectively. The results showed that the film properties, specifically composition can be significantly changed by the total gas pressure and the oxygen flow rate.     

On the structural and electrical characteristics of zinc oxide thin films

ZnO thin films with thickness d = 100 nm were deposited by radio frequency magnetron sputtering onto glass substrate from different targets. The structural analyses of the films indicate they are polycrystalline and have a wurtzite (hexagonal) structure. Crystallites are preferentially oriented with (002) plane parallel to the substrate surface and the samples have low values for surface roughness, between 1.7 nm and 2.7 nm. The mechanism of electrical conduction in the studied films is strongly influenced by this polycrystalline structure and we used Van der Pauw method to analyze these properties. Electrical studies indicate that the ZnO thin films are n-type. For the cooling process, thermal activation energy of electrical conduction of the samples can vary from 1.22 eV to 1.07 eV (for the ZnO layer obtained from for metallic Zn target) and from 0.90 eV to 0.63 eV (for the ZnO layer obtained from ZnO target), respectively. The influence of deposition arrangement and oxidation conditions on the structural and electrical properties of the ZnO films was investigated in detail.     

Effect of thermal annealing time on optical and structural properties of TeO2 thin films

TeO₂ thin films were deposited on quartz substrates by rf reactive sputtering technique from a Te metal target. The obtained samples were annealed in an argon atmosphere at 450 °C for different annealing times up to 90 min. X-ray diffraction studies revealed that the as-grown samples were amorphous and there was no appreciable change in structure for a short annealing time. Thin films became polycrystalline with the tetragonal (α-phase) structure of tellurium dioxide crystal with the increase of the thermal annealing time. The refractive index and optical energy gap of the films were calculated by modelling transmittance spectra. The optical energy gap decreased continuously from 3.83 eV to 3.71 eV with increasing thermal annealing time.     

Effects of thermal treatment on the electrical and optical properties of silver-based indium tin oxide/metal/indium tin oxide structures

In this article, we report the results of the study of thermal treatment effects on the electrical and optical properties of silver-based indium tin oxide/metal/indium tin oxide (IMI) multilayer films. Heat treatment conditions such as temperature and gaseous atmosphere was varied to obtain better electrical and optical properties. We obtained improved electrical properties and observed considerable shift in the transmittance curves after heat treatment. Several analytical tools such as X-ray diffraction, spectroscopic ellipsometer and spectrophotometer were used to explore the causes of the changes in electrical and optical properties. The sheet resistance of the structure was severely influenced by deposition conditions of the indium tin oxide (ITO) layer at the top. Moreover, the shift of optical transmittance could be explained on the basis of the change in refractive indices of ITO layers during heat treatment. The properties of Ag-alloy-based IMI films were compared with those of pure Ag-based ones. Some defects originating from Ag layer corrosion were observed on the surface of ITO-pure Ag–ITO structures, however, their number decreased significantly in the cases of Ag-alloys containing Pd, Au and Cu, though the resistivity values of Ag-alloys were slightly higher than those of silver. Atomic force microscopy measurement results revealed that the surface of the IMI multilayer was so smooth that it meets the required qualifications as the bottom electrode of organic light emitting diodes.