Raman scattering studies of Mn-doped ZnO thin films deposited under pure Ar or Ar + N2 sputtering atmosphere

This paper investigates the anomalous and specific Raman modes present in Mn-doped ZnO thin films deposited using the magnetron co-sputtering method. To trace these peaks, we prepared Mn-doped ZnO films with different Mn concentrations by altering the sputtering power of the Mn target in a pure Ar or Ar + N₂ sputtering atmosphere. A broad band observed in the Raman spectra of heavily Mn-doped ZnO films ranges from 500 to 590 cm^− 1. This band involves the enhanced A₁ longitudinal mode and activated silent modes of ZnO, as well as a characteristic mode of Mn₂O₃. Four anomalous Raman peaks at approximately 276, 510, 645 and 585 cm^− 1 are present in pure and Mn-doped ZnO films deposited under the Ar + N₂ sputtering atmosphere. The peaks at 276 cm^− 1 and 510 cm^− 1 may originate from the complex defects of Zn_i-N_O and Zn_i-O_i, respectively, while the peak at approximately 645 cm^− 1 could be due to a complex defect of Zn_i coupled with both the N and Mn dopants. The results of this study suggest classifying the origins of anomalous and specific Raman peaks in Mn-doped ZnO films into three major types: structural disorder and morphological changes caused by the Mn dopant, Mn-related oxides and intrinsic host-lattice defects coupled with/without the N dopant.     

Stable p-type conductivity and enhanced photoconductivity from nitrogen-doped annealed ZnO thin film

We report on the growth of p-type ZnO thin films with improved stability on various substrates and study the photoconductive property of the p-type ZnO films. The nitrogen doped ZnO (N:ZnO) thin films were grown on Si, quartz and alumina substrates by radio frequency magnetron sputtering followed by thermal annealing. Structural studies show that the N:ZnO films possess high crystallinity with c-axis orientation. The as-grown films possess higher lattice constants compared to the undoped films. Besides the high crystallinity, the Raman spectra show clear evidence of nitrogen incorporation in the doped ZnO lattice. A strong UV photoluminescence emission at ~ 380 nm is observed from all the N:ZnO thin films. Prior to post-deposition annealing, p-type conductivity was found to be unstable at room temperature. Post-growth annealing of N:ZnO film on Si substrate shows a relatively stable p-type ZnO with room temperature resistivity of 0.2 Ω cm, Hall mobility of 58 cm²/V s and hole concentration of 1.95 × 10¹⁷ cm^− 3. A homo-junction p-n diode fabricated on the annealed p-type ZnO layer showed rectification behavior in the current-voltage characteristics demonstrating the p-type conduction of the doped layer. Doped ZnO films (annealed) show more than two orders of magnitude enhancement in the photoconductivity as compared to that of the undoped film. The transient photoconductivity measurement with UV light illumination on the doped ZnO film shows a slow photoresponse with bi-exponential growth and bi-exponential decay behaviors. Mechanism of improved photoconductivity and slow photoresponse is discussed based on high mobility of carriers and photodesorption of oxygen molecules in the N:ZnO film, respectively.     

Carrier transport in polycrystalline transparent conductive oxides: A comparative study of zinc oxide and indium oxide

Highly doped indium-tin oxide films exhibit resistivities ρ as low as  1.2 × 10^− 4 Ω cm, while for ZnO films resistivities in the range of 2 to 4 × 10^− 4 Ω cm are reported. This difference is unexpected, if ionized impurity scattering would be dominant for carrier concentrations above 10²⁰ cm^− 3. By comparing the dependences of the effective Hall mobility on the carrier concentration of ZnO and ITO it is found that grain barriers limit the carrier mobility in ZnO for carrier concentrations as high as 2 × 10²⁰ cm^− 3, independently, if the films were grown on amorphous or single crystalline substrates. Depending on the deposition method, grain barrier trap densities between 10¹² and 3 × 10¹³ cm^− 2 were estimated for ZnO layers. Also, crystallographic defects seem to reduce the mobility for highly doped ZnO films. On the other hand, for ITO films such an influence of the grain barriers was not observed down to carrier concentrations of about 10¹⁸ cm^− 3. Thus the grain barrier trap densities of ZnO and ITO are significantly different, which seems to be connected with the defect chemistry of the two oxides and especially with the piezoelectricity of zinc oxide.     

Realization of high mobility p-type co-doped ZnO: AlN film with a high density of nitrogen-radicals

High mobility p-type ZnO:AlN thin films have been efficiently realized by utilizing pre-activated nitrogen (N) plasma sources with an inductively coupled dual target co-sputtering system. High density of N-plasma-radicals was generated with an additional RF power applied through a ring-shaped quartz-tube located inside the chamber during co-sputtering process. The AlN codoped ZnO film shows excellent p-type behavior with a high mobility and a hole concentration of 154 cm^2°V^− 1s^− 1 and about 3 × 10^18°cm^− 3 at 600 °C, respectively. Electrical properties of p-n homo-junction devices based on p-type ZnO film are also discussed.     

Study on Raman line at 1080.2 cm in ZnO thin films prepared under high RF power

ZnO thin films were prepared on glass or on homo-buffer/glass by a RF magnetron sputtering method at RF power of 100-550 W. The structural and Raman characteristics of the films were analyzed by X-ray diffraction and Raman scattering. There appeared a sharp peak of 1080.2 cm⁻¹ near the A₁(2LO) mode (1156 cm⁻¹) of ZnO in the Raman spectra when the RF power was higher than 300 W. In this case, the (100) peak of ZnO film appeared obviously. It was speculated that the Raman mode at 1080.2 cm⁻¹ was induced by the ordered distribution of Zn_i defects in ZnO lattice.     

Nitrogen-doped p-type ZnO thin films and ZnO/ZnSe p-n heterojunctions grown on ZnSe substrate by radical beam gettering epitaxy

We investigate the p-type doping in ZnO prepared by the method of radical beam gettering epitaxy using NO gas as the oxygen source and nitrogen dopant. Secondary ion mass spectroscopy measurements demonstrate that N is incorporated into ZnO film in concentration of about 8 × 10¹⁸ cm^− 3. The hole concentration of the N-doped p-type ZnO films was between 1.4 × 10¹⁷ and 7.2 × 10¹⁷ cm^− 3, and the hole mobility was 0.9-1.2 cm²/Vs as demonstrated by Hall effect measurements. The emission peak of 3.312 eV is observed in the photoluminescence spectra at 4.2  of N-doped p-type ZnO films, probably neutral acceptor bound. The activation energy of the nitrogen acceptor was obtained by temperature-dependent Hall-effect measurement and equals about 145 meV. The p-n heterojunctions ZnO/ZnSe were grown on n-type ZnSe substrate and have a turn-on voltage of about 3.5 V.     

Chemical states of carbon in amorphous boron carbide thin films deposited by radio frequency magnetron sputtering

Boron carbide thin films were deposited by radio frequency (RF) magnetron sputtering and characterized by X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and high resolution transmission electron microscopy. The results reveal that the structure of thin films deposited at substrate temperatures lower than 350 °C is amorphous. We found that there are four chemical states for carbon in amorphous boron carbide thin films deposited by RF magnetron sputtering. One is the segregated carbon in form of the graphitic inclusions in the thin film identified by Raman spectroscopy and Raman mapping using two strong peaks at ~ 1360 cm^− 1 and ~ 1590 cm^− 1, but the XPS results show that the graphitic inclusions do not connect to the substrate directly. On the surface the carbon forms C=O bonds characterized by the peak of C1s core level at 285.0 eV besides B-C bonds in the boron carbide with the peak of C1s being at 282.8 eV. The detailed analysis of B-C bonds in the boron carbide shows that there are two states for carbon atoms in B-C bonds: in the C-B-C models with C1s peak at 282.3 eV and in the icosahedra with C1s peak at 283.3 eV.     

RF diode reactive sputtering of n- and p-type zinc oxide thin films

We present the relationship between parameters of reactive RF diode sputtering from a zinc oxide (ZnO) target and the crystalline, electrical and optical properties of n-/p-type ZnO thin films. The properties of the ZnO thin films depended on RF power, substrate temperature and, particularly, on working gas mixtures of Ar/O₂ and of Ar/N₂. Sputtering in Ar+O₂ working gas (up to 75% of O₂) improved the structure of an n-type ZnO thin film, from fibrous ZnO grains to columnar crystallites, both preferentially oriented along the c-axis normally to the substrate (〈0 0 2〉 direction). These films had good piezoelectric properties but also high resistivity (ρ≈10³ Ω cm). ZnO:N p-type films exhibited nanograin structure with preferential 〈0 0 2〉 orientation at 25% N₂ and 〈1 0 0〉 orientation for higher N₂ content. The presence of nitrogen N_O at O-sites forming N_O-O acceptor complexes in ZnO was proven by SIMS and Raman spectroscopy. A minimum value of resistivity of 790 Ω cm, a p-type carrier concentration of 3.6×10¹⁴ cm⁻³ and a Hall mobility of 22 cm² V⁻¹ s⁻¹ were obtained at 75% N₂.     

Characterization of fluorine-doped silicon dioxide films by Raman spectroscopy and Electron-spin resonance

We have measured Raman and Electron-spin resonance (ESR) spectra of fluorine-doped SiO₂ films deposited by two different methods. In high-density plasma (HDP) films, the Raman band at about 490 cm^− 1 becomes drastically stronger as the F/Si ratio increases, whereas the Raman band from threefold ring defect is independent of the F/Si ratio. The unusual increase of the intensity of the 490 cm^− 1 band in HDP films has been interpreted in terms of the existence of Si-Si clusters. From a comparison between Raman spectra of HDP film and plasma chemical vapor deposition using tetraethoxysilane (p-TEOS) film with the same F/Si ratios it has been found that HDP film has more Si-Si bonds and threefold ring defects than p-TEOS film. Furthermore, the polarized Raman spectra in the 810 cm^− 1 bands indicate that inhomogeneous SiO₂ clusters of various sizes should exist in the network structure of HDP film. The result of the ESR measurement shows that HDP films have fewer dangling bonds than p-TEOS films. It is considered that many Si-Si clusters, threefold ring defects, and inhomogeneous SiO₂ cluster sizes, and the few dangling bonds in HDP films give rise to the film properties of low stress, good adhesion with Si substrate, and low water permeation.     

p-type doping of ZnO by means of high-density inductively coupled plasmas

A custom-designed inductively coupled plasma assisted radio-frequency magnetron sputtering deposition system has been used to fabricate N-doped p-type ZnO (ZnO:N) thin films on glass substrates from a sintered ZnO target in a reactive Ar + N₂ gas mixture. X-ray diffraction and scanning electron microscopy analyses show that the ZnO:N films feature a hexagonal crystal structure with a preferential (002) crystallographic orientation and grow as vertical columnar structures. Hall effect and X-ray photoelectron spectroscopy analyses show that N-doped ZnO thin films are p-type with a hole concentration of 3.32 × 10¹⁸ cm^− 3 and mobility of 1.31 cm² V^− 1 s^− 1. The current-voltage measurement of the two-layer structured ZnO p-n homojunction clearly reveals the rectifying ability of the p-n junction. The achievement of p-type ZnO:N thin films is attributed to the high dissociation ability of the high-density inductively coupled plasma source and effective plasma-surface interactions during the growth process.     

Structural and mechanical properties of diamond-like carbon films deposited by an anode layer source

An anode layer source is a special ion gun, which can be fed with carbon precursors like acetylene to deposit hard and highly defect-free hydrogenated diamond-like carbon films at room temperature. The present study focuses on the influence of the process parameters — discharge voltage, process pressure and acetylene flow — on structure and mechanical properties of the deposited films. Raman spectra show that an increased discharge voltage yields decreased structural disorder, i.e. a lower C-C sp³ hybridised fraction of carbon atoms in the films. By an elevation of the discharge voltage from 1 to 3 kV the full width at half maximum of the G-band decreases from 194 ± 0.2 cm^− 1 to 183 ± 0.7 cm^− 1. Films deposited at the lowest discharge voltage show in accordance to the spectroscopic data the highest nanohardness (36 ± 1 GPa), stress (− 2.34 ± 0.2 GPa) and reduced elastic modulus (180 ± 4 GPa).     

Ni-doped vertically aligned zinc oxide nanorods prepared by hybrid wet chemical route

Ni-doped zinc oxide (Ni:ZnO) nanorods were synthesized by incorporating nickel in vertically aligned ZnO nanorods. Ni was evaporated onto ZnO nanorods and the composite structure was subjected to rapid thermal annealing for dispersing Ni in ZnO nanorods. The optical band gap decreased with increasing amount of Ni incorporation. The origin of the photoluminescence peak at ∼ 400 nm was related to the defect levels introduced due to substitution of Ni²⁺ in the Zn²⁺ site with annealing. The Raman spectra indicated the presence of the characteristic peak at ∼ 436 cm^− 1 which was identified as high frequency branch of E₂ mode of ZnO. The Fourier Transformed Infrared spectra indicated the existence of the distinct characteristic absorption peak at 481 cm^− 1 for ZnO stretching modes. Current-voltage characteristics indicated that the current changed linearly with voltage for both the doped and undoped samples.     

Ethylene glycol assisted hydrothermal synthesis of flower like ZnO architectures

We describe a simple route to flower like ZnO architectures, based on the decomposition of zinc acetate precursor in water-ethylene glycol solution at 140-160 °C for 1d through hydrothermal method. The PXRD pattern reveals that the ZnO crystals are of hexagonal wurtzite structure. Ethylene glycol plays a key role on the morphology control of ZnO crystals. The SEM images of ZnO products prepared at 140 °C and 160 °C mainly exhibit flower like architecture composed of many rods. Whereas, the product prepared at 180 °C shows bunches accompanying a few number of free rods. TEM results reveal that the rods resemble swords with decrease in size from one end to another. From Raman spectrum, the peaks at 437 cm^− 1, 382 cm^− 1 and 411 cm^− 1 correspond to E₂ (high), A₁ (TO) and E₁ (TO) of ZnO crystals respectively. The photoluminescence spectrum exhibits strong UV emission at ~ 397 nm, which comes from recombination of exciton. The possible mechanism for the formation of flower like ZnO architecture is proposed.     

Low temperature photoluminescence and infrared dielectric functions of pulsed laser deposited ZnO thin films on silicon

C-axis oriented ZnO thin films were grown on silicon (100) and (111) substrates by pulsed laser deposition. Low temperature photoluminescence spectra show besides the peaks of free excitons, of defect bound excitons, and of a donor-acceptor pair transition a new doublet at 3.328/3.332 eV. The doublet seems to originate from the columnar textured ZnO film structure. A corresponding structural dependence of the broadening parameter of the infrared dielectric functions was derived from spectroscopic ellipsometry in the spectral range from 380 to 1200 cm^− 1. The wave numbers of the E₁ transverse optical and A₁ longitudinal optical phonon modes of the ZnO films on silicon are determined to be 406 and 573 cm^− 1, respectively. These values are slightly smaller than those of single-crystalline ZnO thin films on sapphire.     

Structural properties of Ge doped CuGaSe2 films studied by Raman and Photoluminescence spectroscopy

The structural properties of Ge doped polycrystalline CuGaSe₂ films with potential applications in solar cell device technology have been studied by Raman spectroscopy at 300 K and by Photoluminescence (PL) spectroscopy at 300 K and 2 K. The films were intentionally doped with max. 200 keV Ge ions using one- and three-stage ion implantation processes. The Raman spectra of as grown films are dominated by the A₁-mode (breathing mode) of the CuGaSe₂ absorber at 184 cm^− 1. It was found, that in doped films the Raman mode intensities are reduced and the B₂-modes (TO at 249 cm^− 1 and LO at 273 cm^− 1) take over. This implies an increase in structural disorder induced, probably, by bond reorientation effects that favor excitation of asymmetric lattice vibrations (B₂) instead of the symmetric ones (A₁). Moreover, it was found, that the Raman bands of doped films exhibit asymmetric broadening representative of a Fano line-shape. Changes were more pronounced in films doped at one-stage. The PL-emission of films subjected to one-stage process was enhanced, which supports an increase in structural disorder particularly for these films. On the contrary, for films doped in three-stages, the PL bands are less intensive and the Raman bands are less broadened.     

Characterizations of gallium-doped ZnO films on glass substrate prepared by atmospheric pressure metal-organic chemical vapor deposition

Ga-doped zinc oxide (ZnO:Ga) films were grown on glass substrate by atmospheric pressure metal-organic chemical vapor deposition (AP-MOCVD) using diethylzinc and water as reactant gases and triethyl gallium (TEG) as an n-type dopant gas. The structural, electrical and optical properties of ZnO:Ga films obtained at various flow rates of TEG ranging from 1.5 to 10 sccm were investigated. X-ray diffraction patterns and scanning electron microscopy images indicated that Ga-doping plays an important role in forming microstructures in ZnO films. A smooth surface with a predominant orientation of (101) was obtained for the ZnO:Ga film grown at a flow rate of TEG = 7.5 sccm. Moreover, a lowest resistivity of 3.6 × 10^− 4 Ω cm and a highest mobility of 30.4 cm² V^− 1 s^− 1 were presented by the same sample, as evaluated by Hall measurement. Otherwise, as the flow rate of TEG was increased, the average transmittance of ZnO:Ga films increased from 75% to more than 85% in the wavelength range of 400-800 nm, simultaneously with a blue-shift in the absorption edge. The results obtained suggest that low-resistivity and high-transparency ZnO films can be obtained by AP-MOCVD using Ga-doping sufficiently to make the films grow degenerate and effect the Burstein-Moss shift to raise the band-gap energy from 3.26 to 3.71 eV.     

High-rate synthesis of microcrystalline silicon films using high-density SiH4/H2 microwave plasma

A high electron density (> 10¹¹ cm^− 3) and low electron temperature (1-2 eV) plasma is produced by using a microwave plasma source utilizing a spoke antenna, and is applied for the high-rate synthesis of high quality microcrystalline silicon (μc-Si) films. A very fast deposition rate of ∼ 65 Å/s is achieved at a substrate temperature of 150 °C with a high Raman crystallinity and a low defect density of (1-2) × 10¹⁶ cm^− 3. Optical emission spectroscopy measurements reveal that emission intensity of SiH and intensity ratio of H_α/SiH are good monitors for film deposition rate and film crystallinity, respectively. A high flux of film deposition precursor and atomic hydrogen under a moderate substrate temperature condition is effective for the fast deposition of highly crystallized μc-Si films without creating additional defects as well as for the improvement of film homogeneity.     

Evaluation of microstructures and mechanical properties of diamond like carbon films deposited by filtered cathodic arc plasma

Diamond-like carbon (DLC) films were deposited by a cathodic arc plasma evaporation (CAPD) process, using a mechanical shield filter combined with a magnetic filter with enhanced arc structure at substrate-bias voltage ranging from − 50 to − 300 V. The film characteristics were investigated using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and high-resolution transmission electron microscopy (HRTEM). The mechanical properties were investigated by using a nanoindentation tester, scratch test and ball on disc wear test. The Raman spectra of the films showed that the wavenumber ranging from 900 to 1800 cm^− 1 could be deconvoluted into 1140 cm^− 1, D band and G band. The bias caused a significant effect on the sp³ content which was increased with the decreasing of I_D/I_G ratio. The XPS spectra data of the films which were etched by H⁺ plasma indicated the sp³ content are higher than those of the as-deposited DLC films. This implied that there is a sp²-rich layer present on the surface of the as-deposited DLC films. The nanoindentation hardness increased as the maximum load increased. A 380 nm thick and well adhered DLC film was successfully deposited on WC-Co substrate above a Ti interlayer. The adhesion critical load of the DLC films was about 33 N. The results of the wear tests demonstrated that the friction coefficient of the DLC films was between 0.12 and 0.2.     

Tungsten-doped ZnO transparent conducting films deposited by direct current magnetron sputtering

Highly conducting and transparent thin films of tungsten-doped ZnO (ZnO:W) were prepared on glass substrates by direct current (DC) magnetron sputtering at low temperature. The effect of film thickness on the structural, electrical and optical properties of ZnO:W films was investigated. All the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity first decreases with film thickness, and then increases with further increase in film thickness. The lowest resistivity achieved was 6.97 × 10⁻⁴ Ω cm for a thickness of 332 nm with a Hall mobility of 6.7 cm² V⁻¹ s⁻¹ and a carrier concentration of 1.35 × 10²¹ cm⁻³. However, the average transmittance of the films does not change much with an increase in film thickness, and all the deposited films show a high transmittance of approximately 90% in the visible range.     

Study on the Hall-effect and photoluminescence of N-doped p-type ZnO thin films

N-doped, p-type ZnO thin films have been grown by plasma-assisted metal-organic chemical vapor deposition method. The results under optimized growth conditions included a resistivity of 1.72 Ω cm, a Hall mobility of 1.59 cm²/V s, and a hole concentration of 2.29 × 10¹⁸ cm^− 3, and were consistently reproducible. A N-related free-to-neutral-acceptor emission and an associated phonon replica were evident in room temperature photoluminescence spectra, from which the N acceptor energy level in ZnO was estimated to be 180 meV above the valence band maximum.