Effect of Controlled Cooling After Hot Rolling on Mechanical Properties of Hot Rolled TRIP Steel

A three-step cooling pattern on the runout table（ROT）was conducted for the hot rolled TRIP steel.Microstructural evolution during thermomechanical controlled processing（TMCP）was investigated.Processing condition of controlled cooling on a ROT in the laboratory rolling mill was discussed.The results indicated that the microstructure containing polygonal ferrite,granular bainite and a significant amount of the stable retained austenite can be obtained through three-step cooling on the ROT after hot rolling.TMCP led to ferrite grain refinement.Controlled cooling after hot rolling resulted in the stability of the remaining austenite and a satisfactory TRIP effect.Excellent mechanical properties were obtained through TMCP for the hot rolled TRIP steel.     

合金元素和工艺参数对热轧TRIP钢动态相变的影响

利用Gleeble热模拟试验机进行单轴压缩试验,研究了C-Mn-Si TRIP钢和C-Mn-Al-Si TRIP钢过冷奥氏体形变过程的组织演变,分析了合金元素和工艺参数对过冷奥氏体动态相变的影响.与等温相变相比,C-Mn-Si钢和C-MnAl-Si钢动态相变动力学明显加快.与C-Mn-Si钢相比,用质量分数约1%的Al替代Si后,C-Mn-Al-Si钢的A₃温度明显提高,在相同变形工艺条件下C-Mn-Al-Si钢过冷奥氏体动态相变较易发生,而C-Mn-Si钢动态相变得到的铁素体晶粒比较细小.减小动态相变前奥氏体晶粒尺寸,有利于过冷奥氏体动态相变的进行.提高过冷奥氏体形变时的变形温度或应变速率均对动态相变产生一定的阻碍作用,但影响不显著.      

TRIP钢 TMP和热处理过程中的组织演变

介绍了热轧TRIP钢TMP(形变热处理)的精轧阶段(奥氏体未再结晶区变形)、输送台冷却(γ-α两相区的相变)和卷取阶段(贝氏体转变)热轧TRIP钢组织演变的影响因素;冷轧TRIP钢临界区(γ-α区)退火和贝氏体转变区等温处理时的组织演变及其演变过程中TRIP钢残余奥氏体中碳的富集的研究进展。     

Tailoring the Mechanical Properties of Copper-Added Transformation-Induced Plasticity-Aided Multiphase Steel by Thermomechanical Processing

Herein, the microstructure and mechanical properties of a low-alloy Cu-bearing transformation-induced plasticity (TRIP) steel and their dependence on the processing history are investigated. The distributions of the retained austenite and bainite are found to be dependent on the initial cold-rolled microstructure, which can be tailored by the preceding hot-rolling route (unidirectional/cross rolling) and the subsequent cooling rate (furnace/air cooling). Mechanical properties and TRIP effect strongly depend on the initial microstructure, where the air-cooled sheet shows remarkable mechanical properties; while the cross-rolled sheet shows isotropic properties. The addition of copper results in an increase in the amount of the retained austenite, enhancement of strength-ductility balance, and improvement of the hardening behavior of TRIP-assisted high-performance steel.     

Effect of Cooling Method on Microstructure and Mechanical Properties of Hot-Rolled C-Si-Mn TRIP Steel

 The controlled cooling technology following hot rolling process is a vital factor that affects the final microstructure and mechanical properties of the hot-rolled transformation induced plasticity (TRIP) steels. In the present study, low alloy C-Si-Mn TRIP steel was successfully fabricated by hot rolling process with a 450 hot rolling mill. To maximize the volume fraction and stability of retained austenite of the steel, two different cooling methods (air-cooling and ultra-fast cooling “AC-UFC” and ultra-fast cooling, air-cooling and ultra-fast cooling “UFC-AC-UFC”) were conducted. The effects of the cooling method on the microstructure of hot-rolled TRIP steel were investigated via optical microscope, transmission electron microscope and conversion electron Mssbauer spectroscope. The mechanical properties of the steel were also evaluated by conventional tensile test. The results indicated that ferrite and bainite in the microstructure were refined with the cooling method of UFC-AC-UFC. The morphology of retained austenite was also changed from small islands distributing in bainite district (obtained with AC-UFC) to granular shape locating at the triple junction of the ferrite grain boundaries (obtained with UFC-AC-UFC). As a result, the TRIP steel with a content of retained austenite of 1152%, total elongation of 32% and product of tensile strength and total elongation of 27552 MPa·% was obtained.     

控轧控冷TRIP钢的微观相组成及其与力学性能的关系

采用电子背散射衍射技术等实验方法,研究了控轧控冷工艺制备的铌钒微合金化C-Mn-Si系热轧TRIP钢的显微组织及相组成,并分析了与其对应的力学性能.奥氏体轧制过程中的热变形及随后的冷却工艺对最终各相组织的形貌、大小和分布都有直接影响,并决定TRIP钢最终的力学性能.对TRIP钢卷取温度的模拟结果显示,与450和350℃模拟卷取温度相比,400℃模拟卷取温度能使该钢获得更好的综合力学性能.      

热轧相变诱发塑性钢的热模拟实验

 利用Gleeble 1500热应力 应变模拟机研究了铌含量、热变形参数(终轧温度和卷取温度)对相变诱发塑性(TRIP)钢组织和性能的影响。实验结果表明：不含铌实验钢的残余奥氏体量、残余奥氏体相中的碳含量、宏观维氏硬度和抗拉强度与常规低碳硅锰系TRIP钢的水平相当;增加铌含量,残余奥氏体量和残余奥氏体相中的碳含量有所下降,而宏观维氏硬度和抗拉强度提高;铌含量为0014%、终轧温度为780 ℃、卷取温度为400 ℃时,残余奥氏体量、残余奥氏体相中的碳含量与宏观维氏硬度和抗拉强度具有最佳组合。     

Forming response of retained austenite in a C‐Si‐Mn high strength TRIP sheet steel

TRIP sheet steels typically consist of ferrite, bainite, retained austenite, and martensite. The retained austenite is of particular importance because its deformation‐induced transformation to martensite contributes to excellent combinations of strength and ductility. While information is available regarding austenite response in uniaxial tension, less information is available for TRIP steels with respect to the forming response of retained austenite in complex strain states. Therefore, the purpose of this work was to study the austenite transformation behaviour in different strain paths by determining the amount of retained austenite before and after forming. Forming experiments were performed on a high strength 0.19C‐1.63Si‐1.59Mn TRIP sheet steel 1.2 mm in thickness in two different strain conditions, uniaxial tension (ε₁ = ‐2ε₂) and balanced biaxial stretching (ε₁ = ε₂). Specimens were formed to strains ranging from zero to approximately 0.2 effective (von Mises) strain. Specimens were tested both longitudinally and transverse to the rolling direction in uniaxial tension, and subtle mechanical property differences were found. The volume fraction of austenite, determined with X‐ray diffraction subsequent to forming, was found to decrease with increasing strain for both forming modes. Some modification in the crystallographic texture of the ferrite was observed with increasing strain, in specimens tested in the balanced biaxial stretch condition. This trend was not evident in the uniaxial tensile test results. Slight differences were found in the transformation behaviour of the austenite when formed in different strain conditions. More austenite transformed in specimens tested parallel to the rolling direction than transverse to the rolling direction in uniaxial tension. The amount of austenite transformed during biaxial stretching was determined to be greater than the amount transformed in uniaxial tension for specimens tested transverse to the rolling direction at an equivalent von Mises strain. The amount of austenite that transformed in biaxial tension, however, was comparable to the amount of austenite that transformed in specimens tested longitudinal to the rolling direction in uniaxial tension.     

Austempering of Hot Rolled SiMn TRIP Steels

 The austempering after hot rolling in hot rolled Si Mn TRIP (transformation induced plasticity) steels was investigated. The mechanism of TRIP was discussed through examination of the microstructure and the mechanical properties of this kind of steel. The results showed that the strain induced transformation to martensite of retained austenite occurs in hot rolled Si Mn TRIP steels. The sample exhibited a good combination of ultimate tensile strength and total elongation when it was held at the bainite transformation temperature after hot deformation. The stability of retained austenite increases with an increase in isothermal holding time, and a further increase in the holding duration resulted in the decrease of stability. The mechanical properties were optimal when holding for 25 min, and tensile strength and total elongation reached the maximum values (774 MPa and 33%, respectively).     

热轧高锰TRIP/TWIP钢组织性能研究

利用控轧控冷工艺开发了锰质量分数为18.8%的热轧高锰TRIP/TWIP钢板,分析了轧制工艺参数对热轧高锰钢组织和性能的影响,讨论了实验钢的断裂机理。结果表明：通过控轧控冷方法可以热轧出抗拉强度达到940 MPa左右,断裂伸长率在40%以上的高锰钢板。冷却速度和卷取温度等工艺参数对实验钢组织性能影响不是非常明显。高锰钢优异的力学性能是TRIP和TWIP效应共同作用的结果。高锰钢拉伸呈韧性断裂,裂纹多沿奥氏体/马氏体晶界萌生、扩展。     

微合金化热轧TRIP钢的工艺模拟

 借助MMS-300热模拟试验机研究了控轧温度区间、终冷温度、贝氏体区等温处理以及冷却路径对微合金化热轧TRIP钢组织演变规律的影响。结果表明,随着控轧温度区间“下调”,组织中的铁素体晶粒越来越细小,铁素体量逐渐增加,残余奥氏体量则先增加后减少。终冷温度升高时,组织中的残余奥氏体量也呈现出先增加后减少的变化趋势,而贝氏体温度范围等温时间的延长使残余奥氏体量增加。相对于“缓冷+快冷”,轧后采用“快冷+缓冷+超快冷”冷却路径更有助于铁素体晶粒的细化和奥氏体的残留。在“快冷+缓冷+超快冷”冷却路径下,当控轧温度区间为900~840℃,缓冷温度范围为710~680℃,贝氏体等温处理制度为450℃×5min时,组织中的残余奥氏体量达到最高值113%。     

Localized Deformation in Multiphase,Ultra-Fine-Grained 6 Pct Mn Transformation-Induced Plasticity Steel

Multiphase, ultra-fine-grained transformation-induced plasticity (MP UFG TRIP) steel containing 6 mass pct Mn was obtained by cold rolling and intercritical annealing of an initially fully martensitic microstructure. UFG microstructures with an average grain size less than 300 nm were obtained. The amount of austenite in the microstructures, speculated to be formed by diffusionless transformation, was controlled by changing the intercritical temperature. The tensile properties were strongly influenced by the volume amount and the stability of the reversely transformed austenite. The MP UFG TRIP steel was characterized by pronounced localization of the deformation. The deformation band properties were analyzed in detail.     

Effects of Cold Rolling Reduction on Retained Austenite Fraction and Mechanical Properties of High-Si TRIP Steel

 Transformation-induced plasticity-aided steel ［TRIP steel (0. 4C-1. 5Si-1. 5Mn)］ was rolled at room temperature to different thickness reductions (0, 4%, 10%, 20%, 40%, and 60%). The mechanical properties, microstructure and austenite fractions of the rolled samples were measured by tensile test, electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) for each rolling. The deformation behavior was studied based on the analysis of the mechanical properties and microstructure of steel after tensile deformation, aiming at understanding the effects of cold rolling reduction on the decay behavior of the austenite and the change of mechanical properties of the TRIP steels. It was found that increasing rolling reduction increases the yield stress gradually but decreases the total elongation significantly. It is very interesting that after 10% rolling reduction the yield stress is about 1000 MPa but still with 20% total elongation, which gives an excellent combination of yield strength and ductility. Based on the XRD results, it was revealed that in both rolling and tension the austenite volume fraction monotonically decayed with the increase of rolling strain, but the decaying rate is faster in tension than in rolling, which may be ascribed to the higher temperature in rolled specimens than in the tensioned ones during deformation. Experimental results and theoretical reasoning indicate that the decreasing trend of austenite volume fraction with strain can be formulated by a unique equation.     

基于动态相变的C Si Mn系热轧相变诱导塑性钢

 利用热模拟压缩变形,扫描电子显微镜(SEM),X射线衍射(XRD)以及金相实验,探讨了用过冷奥氏体动态相变控制低碳硅锰系相变诱导塑性(TRIP)钢组织的工艺过程,并初步研究了不同工艺条件下组织与性能的关系。结果表明：采用过冷奥氏体动态相变工艺控制TRIP钢的组织是可行的,用相应工艺得到的TRIP钢的抗拉强度达到Rm=900 MPa,伸长率A=24%。     

超细晶中锰钢温轧强化增塑机理

采用Gleeble-3500热模拟试验机测定了不同温度下中锰钢的变形抗力,并通过分阶段拉伸、扫描电镜、电子背散射衍射、X射线衍射等实验手段,对温轧中锰钢中逆转变奥氏体的相变行为进行观察和分析。研究发现,热轧马氏体中锰钢经过600℃温轧及退火后,获得较多较稳定的残余奥氏体,从而实现强度859 MPa和延伸率36%的优良力学性能。拉伸变形前期,锯齿状流变应力现象明显,残余奥氏体提供持续的TRIP效应来提高塑性,此过程中尺寸较大的逆转变奥氏体稳定性差,变形时先发生转变;拉伸变形后期,锯齿状波动消失,超细晶铁素体和马氏体发生塑性变形,马氏体强化及铁素体中的位错强化为主要强化方式。      

Effect of deformation schedule on the microstructure and mechanical properties of a thermomechanically processed C-Mn-Si transformation-induced plasticity steel

Thermomechanical processing simulations were performed using a hot-torsion machine, in order to develop a comprehensive understanding of the effect of severe deformation in the recrystallized and nonrecrystallized austenite regions on the microstructural evolution and mechanical properties of the 0.2 wt pct C-1.55 wt pct Mn-1.5 wt pct Si transformation-induced plasticity (TRIP) steel. The deformation schedule affected all constituents (polygonal ferrite, bainite in different morphologies, retained austenite, and martensite) of the multiphased TRIP steel microstructure. The complex relationships between the volume fraction of the retained austenite, the morphology and distribution of all phases present in the microstructure, and the mechanical properties of TRIP steel were revealed. The bainite morphology had a more pronounced effect on the mechanical behavior than the refinement of the microstructure. The improvement of the mechanical properties of TRIP steel was achieved by variation of the volume fraction of the retained austenite rather than the overall refinement of the microstructure.     

Effect of hot‐rolling conditions on the tensile properties of multiphase steels exhibiting a TRIP effect

TRIP‐assisted multiphase steels have been thoroughly studied in the cold‐rolled and annealed state. The effects of hot‐rolling conditions on these steels are much less studied even though these are of major importance for industrial practice. This study was carried out in order to understand the effect of the hot deformation of austenite on the tensile properties of TRIP‐assisted multiphase steels. Two different compositions and microstructures are investigated. The first one is a low‐carbon steel (mass content of 0.15 %) with a microstructure consisting of an intercritical ferritic matrix, bainite and retained austenite. The second one is a medium‐carbon steel (mass content of 0.4 %) that consists of bainite and retained austenite. Both steels were deformed to various strain levels below the non‐recrystallisation temperature of austenite. The medium carbon steel was deformed in the fully austenitic temperature range whereas the low‐carbon steel was deformed in the intercritical temperature range. In both cases, the prior hot deformation of austenite brings about a large enhancement of the work‐hardening capabilities. In the case of the medium‐carbon steel, this effect can be attributed to a much larger TRIP effect taking place during straining. In the case of the low‐carbon steel, the improvement of the work‐hardening behaviour was attributed to an Interaction between the martensitic transformation and the dislocations already present within the surrounding ferrite matrix.     

退火后冷却方式对冷轧中锰钢微观组织和力学性能的影响

采用拉伸试验、扫描电镜、电子背散射衍射、透射电镜、X射线衍射等手段,研究了冷轧中锰钢(0.2C-5Mn)退火后不同冷却方式下的微观组织特点和拉伸性能.实验钢冷轧退火后为铁素体加逆转变奥氏体的双相组织.退火后空冷可以获得稳定性较高的逆转变奥氏体,且其体积分数也明显高于退火后炉冷.退火后空冷实验钢中的逆转变奥氏体在变形过程中产生持续的TRIP效应,提高强度的同时获得了较高的塑性,强塑积可达到26.5 GPa·%。      

Thermal Stability of Retained Austenite in TRIP Steel After Different Treatments

Thermal decomposition of retained austenite in TRIP steel was investigated by means of differential scanning calorimetry（DSC）.The decomposition curve was abnormal,and the decomposition temperature and the activation energy were measured by the Kissinger method,which were all higher than those in quenched steel.The thermal decomposition data of samples soaked in liquid nitrogen after TRIP treatment were all similar to those without additional low temperature treatment.It indicated that there is a high thermal stability in retained austenite of the TRIP steel at low temperature,which was also proved by XRD analysis.     

Effect of Finishing Rolling Temperature on Microstructure and Mechanical Properties of Microalloyed TRIP Steels

Different samples of TRIP (transformation induced plasticity) steel obtained by two different hot-rolling schedules are investigated by using a SEM (scanning electron microscope). The microstructure is characterized by using an OM (optical microscope) for phase distribution and by EBSD (electron backscatter diffraction) for texture and phase mapping. ODF (orientation distribution function) graphs are used to investigate the effect of recrystallization behavior of the hot-deformed austenite on phase transformation during the controlled cooling process. The mechanical behavior is interpreted in terms of the strength of both hard and soft phases, in combination with the quantity, location and transformation kinetics of the mechanically induced martensite (TRIP effect). The results show that more austenite grains exist in the steels obtained at finishing rolling temperature (FRT) of 750 °C, which inherited the deformation structure after the hot-rolling process. The instantaneous n value (n_i) of those steels is kept high during a large range of strain before failure, while the tensile strength and total elongation of the steels with respect to the different finishing rolling temperatures do not show any significant differences.