Bidirectional Hybrid DWDM‐PON for HDTV/Gigabit Ethernet/CATV Applications

A new scheme for bi‐directional HDTV/Gigabit Ethernet/CATV transmission over a hybrid dense‐wavelength‐division‐multiplexing passive optical network (DWDM‐PON) is proposed and demonstrated. It is based on injection‐locked vertical‐cavity surface‐emitting lasers and distributed‐feedback laser diodes as transmitters. Services with 129 HDTV channels, a 1.25 Gbps Gigabit Ethernet connection, and 77 CATV channels are successfully demonstrated over 40 km single‐mode fiber links. Good performance of bit error rate, carrier‐to‐noise ratio, composite second order, and composite triple beat is achieved in our proposed bidirectional DWDM‐PON.     

A CMOS 5.4/3.24‐Gbps Dual‐Rate CDR with Enhanced Quarter‐Rate Linear Phase Detector

This paper presents a clock and data recovery circuit that supports dual data rates of 5.4 Gbps and 3.24 Gbps for DisplayPort v1.2 sink device. A quarter‐rate linear phase detector (PD) is used in order to mitigate high speed circuit design effort. The proposed linear PD results in better jitter performance by increasing up and down pulse widths of the PD and removes dead‐zone problem of charge pump circuit. A voltage‐controlled oscillator is designed with a ‘Mode’ switching control for frequency selection. The measured RMS jitter of recovered clock signal is 2.92 ps, and the peak‐to‐peak jitter is 24.89 ps under 231–1 bit‐long pseudo‐random bit sequence at the bitrate of 5.4 Gbps. The chip area is 1.0 mm×1.3 mm, and the power consumption is 117 mW from a 1.8 V supply using 0.18 μm CMOS process.     

16‐QAM‐Based Highly Spectral‐Efficient E‐band Communication System with Bit Rate up to 10 Gbps

This paper presents a novel 16‐quadrature‐amplitude‐modulation (QAM) E‐band communication system. The system can deliver 10 Gbps through eight channels with a bandwidth of 5 GHz (71‐76 GHz/81‐86 GHz). Each channel occupies 390 MHz and delivers 1.25 Gbps using a 16‐QAM. Thus, this system can achieve a bandwidth efficiency of 3.2 bit/s/Hz. To implement the system, a driver amplifier and an RF up‐/down‐conversion mixer are implemented using a 0.1 µm gallium arsenide pseudomorphic high‐electron‐mobility transistor (GaAs pHEMT) process. A single‐IF architecture is chosen for the RF receiver. In the digital modem, 24 square root raised cosine filters and four (255, 239) Reed‐Solomon forward error correction codecs are used in parallel. The modem can compensate for a carrier‐frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of 10^?5 at a signal‐to‐noise ratio of about 21.5 dB.     

Voltage‐Mode 1.5 Gbps Interface Circuits for Chip‐to‐Chip Communication

In this paper, interface circuits that are suitable for point‐to‐point interconnection with an over 1 Gbps data rate per pin are proposed. To achieve a successful data transfer rate of multi‐gigabits per‐second between two chips with a point‐to‐point interconnection, the input receiver uses an on‐chip parallel terminator of the pass gate style, while the output driver uses the pullup and pulldown transistors of the diode‐connected style. In addition, the novel dynamic voltage level converter (DVLC) has solved such problems as the access time increase and valid data window reduction. These schemes were adopted on a 64 Mb DDR SRAM with a 1.5 Gbps data rate per pin and fabricated using a 0.10 µm dual gate oxide CMOS technology.     

色散平坦光纤中的高速率PM-16QAM信号传输研究

提出了一种高速率、偏振复用、正交幅度调制信号的色散平坦光纤传输系统,传输速率分别为160 Gbps和256 Gbps,调制格式为PM-16QAM。实验研究了色散平坦光纤链路系统的传输特性,并分别与非零色散位移光纤和标准单模光纤链路传输特性做了比较。实验结果表明,较低输入光功率情况下,PM-16QAM信号在160 Gbps传输50 km时,经色散平坦光纤传输后的误差矢量幅度EVM优于经非零色散位移光纤传输情况0.5%,比特误码率BER优于非零色散位移光纤传输情况两个数量级;色散平坦光纤链路能更好地衰减旁瓣噪声;256 Gbps传输50 km和75 km时,仅在色散平坦光纤链路传输后可以较好地解调出信号;传输距离越长,保持较好特性时输入光功率范围越小。对比160 Gbps和256 Gbps情况,高速率PM-16QAM信号在色散平坦光纤链路的传输特性优于非零色散位移光纤和标准单模光纤链路的传输特性,传输速率越高、传输距离越长效果越明显。     

16‐QAM OFDM‐Based W‐Band Polarization‐Division Duplex Communication System with Multi‐gigabit Performance

This paper presents a novel 90 GHz band 16‐quadrature amplitude modulation (16‐QAM) orthogonal frequency‐division multiplexing (OFDM) communication system. The system can deliver 6 Gbps through six channels with a bandwidth of 3 GHz. Each channel occupies 500 MHz and delivers 1 Gbps using 16‐QAM OFDM. To implement the system, a low‐noise amplifier and an RF up/down conversion fourth‐harmonically pumped mixer are implemented using a 0.1‐μm gallium arsenide pseudomorphic high‐electron‐mobility transistor process. A polarization‐division duplex architecture is used for full‐duplex communication. In a digital modem, OFDM with 256‐point fast Fourier transform and (255, 239) Reed‐Solomon forward error correction codecs are used. The modem can compensate for a carrier‐frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of 10^–5 at a signal‐to‐noise ratio of about 19.8 dB.     

基于 JESD204B 协议的雷达视频信号同步传输设计与实现

以宽带测向接收机中多波束比幅测向为背景,设计了基于JESD204B协议的高速背板视频信号同步传输方案。时钟、JESD204B协议参数的设计合理,实现了2块多通道视频幅度采集板与1块数据处理板之间线速率为6．25 Gbps的高速同步传输,解决了多波束比幅测向前多通道视频信号传输同步问题。     

40Gbps甚短距离并行光传输技术与实验系统

介绍了40Gbps甚短距离(vsR)并行光传输系统的实现和测试.用两片Altera Stratix II GX FPGA分别实现发送/接收转换芯片,通过对FPGA内嵌的吉比特收发器的合理配置,以及在去斜移电路中采用滑动窗口生成器和共用窗口比较器的方法节省了硬件资源;基于异或定位原理,采用二分查找法大大提高了帧同步电路的...     

Independent Turbo Coding and Common Interleaving Method among Transmitter Branches Achieving Peak Throughput of 1 Gbps in OFCDM MIMO Multiplexing

This paper proposes a common interleaving method associated with independent channel‐encoding among transmitter antenna branches in orthogonal frequency and code division multiplexing based on multiple‐input multiple‐output (MIMO) multiplexing to achieve an extremely high throughput such as 1 Gbps using a 100 MHz bandwidth. This paper also investigates the average packet error rate performance as a function of the average received signal energy per bit‐to‐background noise power spectrum density ratio (Eb/N0). We found that the loss in the required average received Eb/N0 of the proposed method is only within approximately 0.3 dB in up to a 12‐path Rayleigh fading channel, using 16QAM and Turbo coding with a coding rate of 5/6. We also clarify that even for a large fading correlation among antenna branches, 1 Gbps is still possible by increasing the transmission power. Therefore, the proposed method reduces the processing rate to 1/4 in the turbo decoder with only a slight loss in the required average received Eb/N0.     

Design and Experiment Results of High‐Speed Wireless Link Using Sub‐terahertz Wave Generated by Photonics‐Based Technology

Using a sub‐terahertz (sub‐THz) wave generated using a photonics‐based technology, a high‐speed wireless link operating at up to 10 Gbps is designed and demonstrated for realization of seamless connectivity between wireless and wired networks. The sub‐THz region is focused upon because of the possibility to obtain sufficient bandwidth without interference with the allocated RF bands. To verify the high‐speed wireless link, such dynamic characteristics as the eye diagrams and bit error rate (BER) are measured at up to 10 Gbps for non‐return‐to‐zero pseudorandom binary sequence data. From the measurement results, a receiver sensitivity of –23.5 dBm at is observed without any error corrections when the link distance between the transmitter and receiver is 3 m. Consequently, we hope that our design and experiment results will be helpful in implementing a high‐speed wireless link using a sub‐THz wave.     

A Four‐Channel Laser Array with Four 10 Gbps Monolithic EAMs Each Integrated with a DBR Laser

A distributed Bragg reflector (DBR) laser and a high speed electroabsorption modulator (EAM) are integrated on the basis of the selective area growth technique. The typical threshold current is 4 to 6 mA, and the side mode suppression ratio is over 40 dB with single mode operation at 1550 nm. The DBR laser exhibits 2.5 to 3.3 mW fiber output power at a laser gain current of 100 mA, and a modulator bias voltage of 0 V. The 3 dB bandwidth is 13 GHz. A 10 Gbps non‐return to zero operation with 12 dB extinction ratio is obtained. A four‐channel laser array with 100 GHz wavelength spacing was fabricated and its operation at the designed wavelength was confirmed.     

10 Gbps Optical Signal Transmission via Long‐Range Surface Plasmon Polariton Waveguide

We demonstrate 10 Gbps optical signal transmission via long‐range surface plasmon polaritons (LR‐SPPs) in a very thin metal strip‐guided geometry. The LR‐SPP waveguide was fabricated as a 14 nm thick, 2.5 μm wide, and 4 cm long gold strip embedded in a polymer and pigtailed with single‐mode fibers. The total insertion loss of 16 dB was achieved at a wavelength of 1.55 μm as a carrier wave. In a 10 Gbps optical signal transmission experiment, the LR‐SPP waveguide exhibits an excellent eye opening and a 2.2 dB power penalty at 10^?12 bit error rate. We confirm, for the first time, that LR‐SPPs can efficiently transfer data signals as well as the carrier light.     

A high‐speed long‐haul wavelength division multiplexing–based inter‐satellite optical wireless communication link using spectral‐efficient 2‐D orthogonal modulation scheme

In this work, we propose a novel multi‐bit/symbol spectral‐efficient optical orthogonal modulation scheme based on simultaneously modulating differential quadrature phase shift keying (DQPSK)‐polarization shift keying (PolSK) in a 16‐channel wavelength division multiplexing (WDM)‐based inter‐satellite optical wireless communication (IsOWC) system. Through numerical simulations, we demonstrate a reliable transportation of 16 × 100 Gbps information over 25 000 km of transmission range with acceptable bit error rate (BER) using the proposed system. Further, the impact of space turbulences (ie, pointing error losses) on the BER performance of the proposed IsOWC link has been evaluated using numerical simulations. The simulation results report a successful transportation of information up to 2.7 μrad receiver pointing error angle with acceptable performance.     

Solid core PCF-based mode selector for MDM-Ro-FSO transmission systems

Radio-over-free-space (Ro-FSO) technology is a combination of free-space optics (FSO) and radio over fiber. It plays a significant role in radio-frequency signal transmission in mobile network communication through high-speed optical carrier without any licensing and costly cables. Photonic crystal fibers also play a significant role to deliver data at faster rate for short haul communication. This paper, for the first time to the author’s best knowledge, utilizes mode division multiplexing in conjunction with solid core PCFs to transmit \(2 \times 2.5\) Gbps–5 GHz data over 2.5 km free-space link. The results are reported in terms of bit error rate, spatial profiles of received modes, mode spectrum of modes and eye diagrams. Furthermore, proposed PCF-MDM-Ro-FSO transmission system is also reported under the impact of atmospheric turbulences.     

Demonstration of CSRZ Signal Generator Using Single‐Stage Mach‐Zehnder Modulator and Wideband CMOS Signal Mixer

In this paper, we demonstrate an electrically band‐limited carrier‐suppressed return‐to‐zero (EB‐CSRZ) signal generator operating up to a 10 Gbps data rate comprising a single‐stage Mach‐Zehnder modulator and a wideband signal mixer. The wideband signal mixer comprises inverter stages, a mixing stage, and a gain amplifier. It is implemented by using a 0.13 μm CMOS technology. Its transmission response shows a frequency range from DC to 6.4 GHz, and the isolation response between data and clock signals is about 21 dB at 6.4 GHz. Experimental results show optical spectral narrowing due to incorporating an electrical band‐limiting filter and some waveform distortion due to bandwidth limitation by the filter. At 10 Gbps transmission, the chromatic dispersion tolerance of the EB‐CSRZ signal is better than that of NRZ‐modulated signal in single‐mode fiber.     

Gbps试验系统中高速串行接口的设计与实现

介绍Gbps无线通信试验系统中高速串行数据接口的设计与实现。按照Gbps无线通信试验系统对高速串行数据的传输要求,数据传输速率超过1 Gb/s,在基于Xilinx IP core技术上对单板上的FPGA进行逻辑设计,实现了符合系统要求的高速串行数据接口。在系统实际调试中,通过ATCA机箱背板进行数据传输,获得了高达Gbps的数据吞吐速率且传输误码率低于10-14。     

Mixed line rate virtual topology design considering nonlinear interferences between amplitude and phase modulated channels

In the last years, the migration from 10 to 40/100 Gbps networks has been proposed as a solution to increase the capacity of transparent optical networks. Initially, the replacement of 10 Gbps legacy equipment was considered. Nowadays, some works point out that the deployment of mixed line rate (MLR) networks, where 10 Gbps and higher bit rate Gbps channels share the same fiber, could be more cost effective than the total replacement of 10 Gbps systems. In this paper, we investigate the planning of 10/40 Gbps MLR networks using the ITU 50 GHz grid, considering nonlinear interferences between 10 and 40 Gbps channels, which degrade the quality of transmission. This approach is novel in the literature. In addition, we conduct a set of tests normalizing the length of fiber links, to observe the trends in MLR planning for different network sizes.     

Gigabit DSL

This paper applies multiple-input multiple-output (MIMO) transmission methods to multiwire communication systems. Using channel matrices generated from a binder MIMO channel model, a performance assessment of digital subscriber line (DSL) technology based on MIMO transmission methods finds that symmetric data rates of more than 1 Gbps are achievable over four twisted pairs (category 3) for a 300 m range. Similar results are also obtained for a ldquoquadrdquo cable. To achieve this data rate, this paper proposes that the source and load be excited using common mode.     

Presence of residual echo and impulsive noise

A general analysis is presented for the jitter performance of a common type of symbol timing recovery (STR) system employed in a digital subscriber loop (DSL) transceiver for high-speed digital data transmission over twisted copper pair cables in the presence of residual echo and impulsive noise (IN). Numerical results, obtained for an experimental study of a timing recovery system, show that the presence of these disturbing signals can substantially degrade the STR performance     

Gbps无线传输关键技术及试验验证系统

面向IMT-Advanced系统高达Gbps的无线传输速率需求,本文针对Gbps无线传输关键技术及其实现进行了有效研究。本文介绍了所提出的Gbps无线传输技术的空中接口参数、帧协议、无线链路及物理层关键技术,引进了硬件平台与试验验证系统。多项研究成果以标准提案的形式被国际、国内标准组织接纳,并在Gbps试验验证系统上取得重要进展,实现了Gbps无线传输,演示了未来移动通信系统的典型业务,推动了我国4G移动通信技术研究的发展。