Laser welding in the dental laboratory: an alternative to soldering

Only recently has laser welding been applied to dental technology, primarily as an alternative to soldering. This article addresses how the laser is used for welding, the effect welding has on metals as the energy is converted into heat and reacts with the alloy's surface and the practicality of laser welding in the dental laboratory. A step-by-step procedure for accomplishing laser-welded connections in a fixed partial denture is included. A laser-welded clasp repair using wrought wire and the addition of custom cast parts welded to an existing removable partial denture framework on the master model are also shown.     

Effect of polymerization temperature and time on the residual monomer content of denture base polymers

The aim of this study was to investigate the effect of polymerization time and polymerization temperature on the residual methyl methacrylate (MMA) content of two heat-cured and two autopolymerized denture base polymers. Gas chromatography was used to determine the residual MMA content of three test specimens of each type of polymer. Increasing the polymerization temperature for the autopolymerized denture base resins from 30 degrees C to 60 degrees C decreased the residual MMA content of the polymer from an average of 4.6 wt% to 3.3 wt%. With the heat-cured denture base resins, a curing cycle at a polymerization temperature of 70 degrees C followed by a period at 100 degrees C significantly reduced the residual monomer content of the polymer when compared with a resin cured at 70 degrees C only. Polymerizing the heat-cured denture base resin at 100 degrees C only for various lengths of time significantly affected the residual MMA content of the polymer. The lowest residual MMA content (0.07 wt%) was obtained by polymerizing the heat-cured denture base resin at 100 degrees C for 12 h. The results of this study suggest that the polymerization temperature and polymerization time considerably affect the residual MMA content of denture base polymers.     

Repair with a surveyed cast clasp while patient retains the partial denture

A technique is described that allows a removable partial denture with a broken clasp or a removable partial denture in which an abutment has been extracted to be restored by the reattachment of a new cast clasp component or a complete surveyed clasp assembly. The technique is applicable to most clasp designs and can include attachment to the acrylic denture base or the metal major connector. The technique is distinguished from other repair techniques by (1) providing a cast clasp replacement, (2) allowing the patient to retain the prosthesis during the repair, (3) generating a precisely formed surveyed clasp assembly by the laboratory, and (4) including an efficient transfer mechanism for the precision clasp created in the laboratory to be attached to the removable partial denture in the dental office. A two-step impression procedure is used to ensure proper relation of the partial denture to the abutments.     

新型化学热处理在连铸结晶器上的应用

新型化学热处理工艺已用于连续铸钢机的结晶器。实践证明 ,经化学热处理的结晶器具有良好的导热性 ,耐磨性 ,抗氧化性和高的热疲劳强度 ,显著延长使用寿命 ,降低成本。用实验数据和现场使用结果 ,分析讨论这些特性     

Increasing the Adhesion of Plastic Coatings to Metal Dentures

A technology for plasma-chemical modification of the surface of a denture metal base for strengthening the adhesion of the latter to a plastic coating has been developed. The optimal gas composition for plasma-chemical etching was determined. It has been established that the adhesion layer formed due to this treatment enhances the adhesion of the metal base to evicrol and carbodent plastics by a factor of 2.4-4.6. The proposed surface modification is not labor-intensive, the etching process is short (15-20 min), and the equipment used is not complicated. Owing to these circumstances, the technology can be easily applied in dental practice.     

Pharmacokinetics and toxicity of 120-hour continuous-infusion hydroxyurea in patients with advanced solid tumors

This study investigated the thickness of a swollen layer between heat-activated and autopolymerized denture base polymer based on poly(methyl methacrylate) and autopolymerized repair acrylic resin. The repair surfaces of polymerized poly(methyl methacrylate) resin specimens (n = 5) were wet with methyl methacrylate liquid for 0, 0.5, 3, 30, or 60 minutes before the mixed repair resin was applied and polymerized to the surface of the specimen. The specimens were wet ground to a thickness of 0.15 mm, and the repair joint was examined using a light microscope. The thickness of the layer of swollen poly(methyl methacrylate) at the repair joint was measured from the micrographs. Both the type of polymer, ie, heat-activated or autopolymerized, and the wetting time of the repair surface with methyl methacrylate had a significant effect on the thickness of the swollen layer (P < .001). Prolonged wetting time of the repair surface of the autopolymerized poly(methyl methacrylate) increased the thickness of the swollen layer (r = .944, P = .000), but had less effect on the thickness of the swollen layer of heat-activated poly(methyl methacrylate) (r = .391, P = .005). This study suggests that methyl methacrylate diffuses more easily into an autopolymerized poly(methyl methacrylate) than into heat-activated poly(methyl methacrylate) during the repair of denture base polymer.     

Up- and down-regulation of calpain inhibitor polypeptide, calpastatin, in postischemic hippocampus

A dental student developed swelling of the lips and peri-oral urticaria, immediately after placement of a dental rubber dam during a chairside demonstration of clinical dentistry. A provisional diagnosis of a Type I hypersensitivity reaction to natural rubber latex was made and an appointment organised for specialist investigations. The student reported an atopic history and allergy to peanuts. A Radioallergosorbent Test (RAST), to measure Ig-E antibodies to latex, was positive. The dental student was given advice concerning the avoidance of natural rubber latex. Dental staff must be aware of potentially serious reactions to natural rubber latex in the dental surgery.     

Fimbrial-mediated colonization of murine teeth by Actinomyces naeslundii

PURPOSE: The hardness, porosity, and adaptation of removable partial dentures fabricated with one heat-polymerized denture base resin and two resins designed for microwave polymerization were evaluated. MATERIALS AND METHODS: Five prostheses were evaluated for each resin. Adaptation of the denture bases to the master cast was evaluated by spatial orientation and mean weight of residual impression material. The prostheses were than embedded in epoxy resin and sectioned for evaluation of resin hardness (Knoop hardness) and microporosity. RESULTS: There were no significant differences in the adaptation of the acrylic resin bases for Acron MC and Ch Lucitone. There was no significant difference in the mean Knoop hardness values for any of the resin bases near and away from the metal. None of the denture bases showed porosity greater than 100 microns. CONCLUSIONS: Both resin bases formulated for microwave polymerization were effectively polymerized around metal frameworks without adverse effects on resin hardness or porosity. Justi Denture Base material had poorer base adaptation than the other two resins.     

Dental materials: 1996 literature review. Part 2

This critical review of the published literature on dental materials for the year 1996 has been compiled by the Dental Materials Panel of the UK. It continues the series of annual reviews started in 1973 and published in the Journal of Dentistry. Emphasis has been placed upon publications which report upon the materials science or clinical performance of the materials. The review has been divided by accepted materials classifications (fissure sealants, glass polyalkenoate cements, dentine bonding, dental amalgam, endodontic materials, casting alloys, resin-bonded bridges and ceramo-metallic restorations, ceramics, denture base resins and soft lining materials, impression materials, implants materials, orthodontic materials, biomechanics and image processing, resin composites and casting investment materials and waxes). Three hundred and thirteen articles have been reviewed.     

Allelic polymorphism in the coding region of human T cell receptor V beta 12 gene

Many bilateral distal extension removable partial dentures possess insufficient guidance to control their dislodgement. When such a situation is observed, the tips of retentive clasps must be located in both an occlusogingival and mesiodistal (away from the denture base area) undercut. The specific location can be identified with a dental surveyor that has been adapted to function in two planes. Details of the adaptation process and use of the surveyor are described.     

A follow-up study on changes in mastication after insertion of mandibular bilateral free end saddle denture by EMG]

The purpose of this study was to investigate changes in the mandibular shortened arch, whose occlusal deficit had been reconstructed by removable partial denture, during mastication by using the EMG analyzing system. A total of 5 shortened dental arch patients was provided with RPDs, and observed by a sophisticated masticatory analyzing system using EMG, before and one day, about 2 weeks, 3 months, after denture insertion. The conclusions were as follows: i) The elements of the shortened arch during mastication, that is, the duration, interval, and cycletime, were prolonged at the time of insertion of RPD, but 3 months after denture insertion, they were shortened to almost the same state as before treatment. ii) Prosthetic treatment for shortened dental arch improved revitalization of functional musculatures, and their rhythmicity of functional procedure. iii) The functional tongue room for optimal bolus position in mastication was provided by insertion of mandibular bilateral free end saddle removable partial denture.     

Bond strength of six soft denture liners processed against polymerized and unpolymerized poly(methyl methacrylate)

The bond strength of six commercial soft denture liners was evaluated by a two-phase tensile test. The soft denture liners investigated were VinaSoft, Prolastic, Flexor, Molloplast-B, Novus, and SuperSoft. The samples were fabricated by processing them (1) against polymerized poly(methyl methacrylate), and (2) against unpolymerized poly(methyl methacrylate). The soft denture liners were processed according to the manufacturers recommendations. The samples were tested using an Instron Universal Testing Machine. The mode of failure, adhesive or cohesive, was also recorded. The bond strength when processed against unpolymerized poly(methyl methacrylate) ranged from 0.48 to 2.60 MPa, and when processed against polymerized poly(methyl methacrylate) the bond strength ranged from 0.94 to 2.56 MPa. A two-way analysis of variance (P = .05) revealed a significant increase in bond strength when the liners were processed against polymerized poly(methyl methacrylate), except for Novus, which had no change, and VinaSoft, which decreased. The Tukey interval between materials was .22 and between methods of polymerization was .08. Four of the six liners investigated demonstrated increased bond strength when processed against polymerized poly(methyl methacrylate). It was concluded that bonding can be influenced by the processing method.     

Orthostatic tests after a 4-day confinement or simulated weightlessness

As far back as 1975, this study has been undertaken longitudinally from sample of 723 subjects, aged from 18 to 89. Its main objective was primarily to point out the different factors involved in both dental and skeletal structures changes, in adults when a full denture was functional. Also, the author has tried to assess if this evolution can be quantified on lateral cephalograms, according to sex and architectural type.     

Accuracy and porosity of denture bases submitted to two polymerization cycles

In this study was verified accuracy and porosity of denture bases submitted to double cycles of polymerization. Thirty-Six master casts were made in dental stone from the impression of the metal die. They were divided in three groups. Denture bases of conventional acrylic resin were made on the casts of the groups I (GI-control) and II (GII), polymerized in water bath during 9 hours at 73 degrees C, and specific resin for microwave polymerization were made on the casts of the group III (GIII) and cured at 500 W during 3 minutes. Accuracy was verified by the weight of a impression material put between the denture base and cast die under load of 2 Kg. Afterwards, all the denture bases were relined by addition method and those of the group I and II were relined with the same material and polymerization technic. The denture bases of the group II were filled with the same resin, however cured in microwave oven with 500 W during 3 minutes. Accuracy was reevaluated. The porosity was verified by the immersion of the specimens in a solution of permanent black ink and the pores were counted through a stereo light microscope under magnification of 6.3 x. The average and standard deviation obtained for accuracy before and after the relining were respectively: GI: 0.63 +/- 0.02 - 0.66 +/- 0.03; GII: 0.63 +/- 0.03 - 0.68 +/- 0.03: GIII: 0.58 +/- 0.02 - 0.80 +/- 0.05. There was a significant difference (p < 0.05 as tested by Tukey) only for the group III. The average and standard deviation for porosity before and after the relining were respectively: GI: 8.33 +/- 0.63 - 9.25 +/- 0.85; GII: 8.17 +/- 0.98 - 10.08 +/- 1.63: GIII: 5.41 +/- 0.78 - 6.58 +/- 1.02. There was a significant difference (p < 0.05) for the group III before relining. The conclusion is that after relining, the conventional resin cured by water bath or microwaves energy showed a better adaptation, and the highest number of pores.     

Latex allergies and adverse reactions: a review of the literature

In the last few years, the allergenic potential of latex has been receiving greater attention. While latex allergies have been widely reported in the literature, the prevalence and severity have rapidly increased in the last few years. The role of rubber in the prevention of HIV infection has played a part in recognizing the allergenic potential, as with increased emphasis on infection control in the dental office has come an increase in complaints of adverse reactions to surgical gloves. A review of the literature reveals latex allergy problems to be not confined to gloves, but to articles of clothing, rubber dam material, and other latex-containing materials. Life-threatening cases have been reported. Little information in the literature concerns the extent of the problem among dental personnel. The dental professional may be faced with not only discomfort for the dental staff, but also compromising reactive possibilities in certain patients. There is a need for development of alternative protective products for the dental office, since elimination of barrier protection is not a viable alternative to infection control.     

Breeding of Philander frenata (Didelphimorphia, Didelphidae) in captivity

STATEMENT OF PROBLEM: Because water sorption of autopolymerizing acrylic reline resins is accompanied by volumetric change, it is a physical property of importance. As residual monomer leaches into the oral fluids and causes tissue irritation, low solubility of these resins is desired. Another requirement is a satisfactory bond between the autopolymerizing acrylic resins and the denture base acrylic resin. PURPOSE: This study compared the water sorption, solubility, and the transverse bond strength of 2 autopolymerizing acrylic resins (Duraliner II and Kooliner) and 1 heat-polymerizing acrylic resin (Lucitone 550). MATERIAL AND METHODS: The water sorption and solubility test was performed as per International Standards Organization Specification No. 1567 for denture base polymers. Bond strengths between the autopolymerizing acrylic resins and the heat-polymerizing acrylic resin were determine with a 3-point loading test made on specimens immersed in distilled water at 37 degrees C for 50 hours and for 30 days. Visual inspection determined whether failures were adhesive or cohesive. RESULTS: Duraliner II acrylic resin showed significantly lower water sorption than Kooliner and Lucitone 550 acrylic resins. No difference was noted in the solubility of all materials. Kooliner acrylic resin demonstrated significantly lower transverse bond strength to denture base acrylic resin and failed adhesively. The failures seen with Duraliner II acrylic resin were primarily cohesive in nature. CONCLUSIONS: Autopolymerizing acrylic reline resins met water sorption and solubility requirements. However, Kooliner acrylic resin demonstrated significantly lower bond strength to denture base acrylic resin.     

Metals used to fabricate removable partial denture frameworks

This article will help the dental technician choose from among the many alloys available for fabricating dental prostheses. It will explain terminology and compare and explain inherent properties and characteristics of alloys. Although all of the materials discussed produce a clinically acceptable removable partial denture framework, the predominantly base alloys dominate the market because of the low cost of the metal, case of casting, high yield strength and modulus of elasticity.     

SS400超细晶粒钢及其焊接接头的疲劳裂纹扩展速率

SS400钢是一种细晶强化的新一代钢铁材料．焊接对其疲劳性能的影响是人们关注的问题。笔者参照美国材料试验学会标准ASTME647—83的规定．采用紧凑拉伸CT试件对SS400钢及其焊接接头CT试件的疲劳裂纹扩展速率进行了测试。发现：母材的疲劳裂纹扩展存在两个不同速率的阶段,焊缝及热影响区的疲劳裂纹扩展速率均低于母材;热影响区的疲劳裂纹扩展速率介于焊缝与母材之间;焊接接头组织和性能的变化并未导致SS400钢疲劳性能的降低。     

双轴等拉低周疲劳实验装置

本文给出能在一般单向加载液压疲劳试验机上做双轴等拉低周疲劳实验研究的双向拉伸装置,并对有关影响因素进行了讨论。
本试验是在百吨液压低周疲劳试验机上进行的。双向拉体装置已经受近百万次疲劳载荷,其中交变载荷幅围5.5,t亦经受近20万次。在使用过程,各构件完好合手使用要求,将十字试样进行低周疲劳断裂试验,成功地开出合格裂纹,用它进行超速条件下叶轮材料性能研究亦取得初步结果。可以认为它适用于平而应力集中问题低周疲劳性能的研究。若使用液压高、中周疲劳试验机,它还可用于双轴载荷下裂纹试样裂纹扩展的研究。
本文指出了双向拉伸装置有待改进的方面。