共查询到19条相似文献,搜索用时 156 毫秒
1.
2.
详细介绍了在线式偏振无关光隔离器和微型化偏振相关光隔离器的工作原理,以及两种隔离器系列的各项性能指标。其主要性能指标达到国内先进水平,并达到了90年代国外同类光隔离器的水平。 相似文献
3.
磁光隔离器是光通信系统中的关键器件.为确保光通信系统宇航应用可靠性,对磁光隔离器的宇航应用评估进行了研究.在介绍磁光隔离器的工作原理、内部关键元件法拉第旋转片、装配工艺和典型光学参数的基础上,重点从磁光隔离器宇航应用评估基础验证设计方面展开磁光隔离器宇航应用评估研究.由此,进行了验证指标体系的设计、失效模式的分析、验证... 相似文献
4.
5.
R.Joshi Chung-LinWu M.Narayanan K.Ramdass 《今日电子》2004,(8):40-41
光耦合器(也称作光隔离器)是半导体器件,容许电信号在电路或系统之间传送,并保证电路或系统之间被电气隔离。典型的双列直插式(DIP)光耦合器包含三个基本单元:一个红外(IR)发光二极管(LED)、一个输出光电检测器,以及对于相互连接至关重要耦合介质。 相似文献
6.
7.
光纤光隔离器研制的进展 总被引:7,自引:1,他引:6
本文介绍了光隔离器国内外研制的现状与发展,扼要说明光隔离器的原理,结构,分类与器件小型化等问题。最后提出了该器件今后发展方面的几个问题。 相似文献
8.
9.
介绍WDM系统光节点所用到的器件,如波长转换器、光分插复用器及其使用的光隔离器和光环形器. 相似文献
10.
11.
钒酸钇晶体楔型光隔离器 总被引:5,自引:1,他引:4
介绍了用钒酸钇晶体的与偏振无关的Wedge型光隔离器的基本原理,用琼斯矢量法得到了插入损耗和隔离度的数学表达式,并介绍了隔离器的结构设计.制作的隔离器光纤到光纤的插入损耗为1.04dB,隔离度为42dB,回程损耗为44.3dB,偏振灵敏度≤0.2dB,带宽大于40nm,体积为10×10×40mm3. 相似文献
12.
光纤F-P传感器偏振互相关解调中光楔参数的影响研究 总被引:3,自引:1,他引:2
对光纤法布里-珀罗(F-P)腔长偏振互相关解调法中的双折射光楔进行了理论和实验研究,建立了双折射光楔对干涉光程差影响的数学模型,并进行了数值仿真。仿真结果表明,当楔角为4°时,要保证楔面内任意点处的光程误差在15nm以内,入射角应小于0.3°,光楔光轴倾斜应小于0.8°,楔面垂直度误差应小于0.15°。采用光楔进行了偏振光干涉实验,实验干涉条纹与理论条纹基本一致,实验干涉条纹的倾斜度与理论倾斜度相差0.02°。 相似文献
13.
14.
文章介绍了单楔晶体波片消偏器的工作原理,应用Stokes矢量对其消偏性能进行仿真分析,提出了双楔晶体波片消偏器,并对两种结构的消偏器性能进行了比较.结果表明:光束直径与楔角满足一定关系时,楔形晶体波片消偏器可以实现完全消偏,双楔所要求的光束直径为单楔的一半.最后给出了双楔形消偏器和光纤相接的应用实例. 相似文献
15.
16.
Continuous-wave fiber optical parametric amplifier with 60-dB gain using a novel two-segment design 总被引:3,自引:0,他引:3
K.K.Y. Wong K. Shimizu K. Uesaka G. Kalogerakis M.E. Marhic L.G. Kazovsky 《Photonics Technology Letters, IEEE》2003,15(12):1707-1709
We have obtained 60 dB of internal (ON-OFF) gain with a continuous-wave fiber optical parametric amplifier by using an isolator between two fiber segments to increase the pump stimulated Brillouin scattering threshold. Subdecibel penalties were measured for transmission of 10-Gb/s signals, with 35 dB of gain. 相似文献
17.
18.
In this paper, a high-power erbium-doped fiber amplifier (EDFA) for the temperature sensor system is theoretically designed and experimentally demonstrated. It consists of an erbium-doped fiber that is pumped bidirectionally with two 980-nm high-power laser diodes (LDs). At the EDFA input, an optical isolator (ISO) is used to ensure that the signal pulse transmits forward only. After that, a wavelength division multiplexer (WDM) is employed to combine the forward pump laser (980 nm) and incident optical pulse (1550nm) into the erbium-doped fiber for direct amplification in the optical domain. At the EDFA output, another WDM couples the backward pump laser (980 nm) into the erbium-doped fiber and outputs the amplified optical pulse (1550 nm) with an ISO followed to isolate the backscattering light. According to this structure, we carried out the experiment in the condition as follows. For 980 nm pump LD, the operating current is 590 mA, and the setting temperature is 25℃. For EDFA, the length of erbium-doped fiber is 12.5 m, and the power of 1550 nm input signal is 1.5 mW. As a result, the power of pump LD is 330 mW, and the power uncertainty is 0.5%. The power of EDFA output at 1550 nm is 300 mW, and the power uncertainty is ±3 mW. 相似文献