Synthesis and characterization of MoOx-Pt/C and TiOx-Pt/C nano-catalysts for oxygen reduction

The oxygen reduction reaction (ORR) was studied at carbon supported MoO_x-Pt/C and TiO_x-Pt nanocatalysts in 0.5 mol dm⁻³ HClO₄ solution, at 25 °C. The MoO_x-Pt/C and TiO_x-Pt/C catalysts were prepared by the polyole method combined by MoO_x or TiO_x post-deposition. Home made catalysts were characterized by TEM and EDX techniques. It was found that catalyst nanoparticles were homogenously distributed over the carbon support with a mean particle size about 2.5 nm. Quite similar distribution and particle size was previously obtained for Pt/C catalyst. Results confirmed that MoO_x and TiO_x post-deposition did not lead to a significant growth of the Pt nanoparticles.The ORR kinetics was investigated by cyclic voltammetry and linear sweep voltammetry at the rotating disc electrode. These results showed the existence of two E − log j regions, usually observed with polycrystalline Pt in acid solution. It was proposed that the main path in the ORR mechanism on MoO_x-Pt/C and TiO_x-Pt/C catalysts was the direct four-electron process with the transfer of the first electron as the rate-determining step. The increase in catalytic activity for ORR on MoO_x-Pt/C and TiO_x-Pt/C catalysts, in comparison with Pt/C catalyst, was explained by synergetic effects due to the formation of the interface between the platinum and oxide materials and by spillover due to the surface diffusion of oxygen reaction intermediates.     

Novel methanol electro-oxidation catalyst assisting with functional phthalocyanine supports

Novel electro-catalyst based on phthalocyanine stabilized Pt colloids has been developed for methanol electro-oxidation. Water soluble Cu²⁺ phthalocyanine functioned with sulfonic groups were selected as catalyst supports because of the relatively high catalytic activity of Pt catalyst and nearly the same catalytic selectivity complex with Cu-phthalocyanine, compared to others that chelated with Fe, Co and Ni ions. The as-resulting Pt-CuTsPc catalysts have average particle size of 2 nm and narrow size distribution. With the assistance of CuTsPc supports, the methanol electro-oxidation activity and poison tolerance of Pt catalyst have a significant increase. I_f/I_b ratio (anodic peak current density, forward to backward) of the Pt-CuTsPc/C catalysts also has obvious increase to 2.5, from value of 0.8 for pure Pt/C catalyst. The reaction Tafel slope of Pt-CuTsPc/C catalysts is 56.6 mV dec⁻¹, much smaller than that of the Pt/C catalyst. The transient current density on Pt-CuTsPc/C at 0.60 V is enhanced to 650% of that on the Pt/C catalyst while the enhancement factor R for comparison of steady-state current obtained on Pt-CuTsPc/C and Pt/C catalyst varies between 111% and 534% in the potential region of 0.3-0.75 V.     

Rational determination of exchange current density for hydrogen electrode reactions at carbon-supported Pt catalysts

The rotating disk electrode (RDE) is a useful technique for precise determination of exchange current density (j₀) in electrochemistry. For the study of powder catalysts, a common practice is to apply the powder onto an inert disk substrate (such as glassy carbon). However, this approach in its usual version will lead to wrong results for the exchange current density of hydrogen electrode reactions at carbon-supported Pt nanoparticles (Pt/C) because of the poor utilization of the loaded Pt nanoparticles. Our new approach is to dilute the Pt/C powder with a large amount of pristine carbon support to make the catalyst layer. In this way, all the catalyst particles in the catalyst layer have nearly the same and much enhanced mass transport so that rational exchange current density can be obtained. Using the new approach, the current density for hydrogen electrode reactions at Pt/C in 0.1 M perchloric acid at 25 °C is found to be 27.2 ± 3.5 mA/cm² with an apparent activation energy 43 kJ/mol. These results are in agreement with the j₀ estimation based on real fuel cell experiments.     

Nano-stuctured Pt-Fe/C as cathode catalyst in direct methanol fuel cell

Pt-Fe/C catalysts were prepared by a modified polyol synthesis method in an ethylene glycol (EG) solution, and then were heat-treated under H₂/Ar (10 vol.%) at moderate temperature (300 °C, Pt-Fe/C300) or high temperature (900 °C, Pt-Fe/C900). As comparison, Pt-Fe/C alloy catalyst was prepared by a two-step method (Pt-Fe/C900B). X-ray diffraction (XRD) and transmission electron microscopy (TEM) images show that particles size of the catalyst increases with the increase of treatment temperatures. Pt-Fe/C300 catalyst has a mean particle size of 2.8 nm (XRD), 3.6 nm (TEM) and some Pt-Fe alloy was partly formed in this sample. Pt-Fe/C900B catalyst has the biggest particle size of 6.2 nm (XRD) and the best Pt-Fe alloy form. Cyclicvoltammetry (CV) shows that Pt-Fe/C300 has larger electrochemical surface area than other Pt-Fe/C and the highest utilization ratio of 76% among these Pt-based catalysts. Rotating disk electrode (RDE) cathodic curves show that Pt-Fe/C300 has the highest oxygen reduction reaction (ORR) mass activity (MA) and specific activity (SA), as compared with Pt/C catalyst in 1.0 M HClO₄. However, Pt-Fe/C catalyst does not appears to be a more active catalyst than Pt/C for ORR in 1.0 M HClO₄ + 0.1 M CH₃OH. Pt-Fe/C300 exhibits higher ORR activity and better performance than other Pt-Fe/C or Pt/C catalysts when employed for cathode in direct methanol single cell test, the enhancement of the cell performance is logically attributed to its higher ORR activity, which is probably attributed to more Pt⁰ species existing and Fe ion corrosion from the catalyst.     

Preparation of supported PtRu/C electrocatalyst for direct methanol fuel cells

In this work, high-surface supported PtRu/C were prepared with Ru(NO)(NO₃)₃ and [Pt(H₂NCH₂CH₂NH₂)₂]Cl₂ as the precursors and hydrogen as a reducing agent. XRD and TEM analyses showed that the PtRu/C catalysts with different loadings possessed small and homogeneous metal particles. Even at high metal loading (40 wt.% Pt, 20 wt.% Ru) the mean metal particle size is less than 4 nm. Meanwhile, the calculated Pt crystalline lattice parameter and Pt (2 2 0) peak position indicated that the geometric structure of Pt was modified by Ru atoms. Among the prepared catalysts, the lattice parameter of 40-20 wt.% PtRu/C contract most. Cyclic voltammetry (CV), chronoamperometry (CA), CO stripping and single direct methanol fuel cell tests jointly suggested that the 40-20 wt.% PtRu/C catalyst has the highest electrochemical activity for methanol oxidation.     

Effect of chemisorbed carbon monoxide on Pt/C electrode on the mechanism of the hydrogen oxidation reaction

The influence of poisoning of Pt catalyst by CO on the kinetics and mechanism of H₂ oxidation reaction (HOR) at Pt/C electrode in 0.5 mol dm⁻³ HClO₄, saturated with H₂ containing 100 ppm CO, was examined with rotating disc electrode (RDE) at 22 °C. Commercial carbon black, Vulcan XC-72 was used as support, while Pt/C catalyst was prepared by modified polyol synthesis method in an ethylene glycol (EG) solution. The kinetically controlled current (I_k) for the HOR at Pt/C decreases significantly at CO coverage (Θ_CO) > 0.6. For Θ_CO < 0.6 the HOR takes place through Tafel-Volmer mechanism with Tafel reaction as rate-determining step at the low CO coverage, while Volmer step controls the overall reaction rate at the medium CO coverage. When CO coverage is higher then 0.6, Heyrovsky-Volmer mechanism is operative for the HOR with Heyrovsky as the rate-determining step (rds).     

CoPdx oxygen reduction electrocatalysts for polymer electrolyte membrane and direct methanol fuel cells

The electrochemical activity of carbon-supported cobalt-palladium alloy electrocatalysts of various compositions have been investigated for the oxygen reduction reaction in a 5 cm² single cell polymer electrolyte membrane fuel cell. The polarization experiments have been conducted at various temperatures between 30 and 60 °C and the reduction performance compared with data from a commercial Pt catalyst under identical conditions. Investigation of the catalytic activity of the CoPd_x PEMFC system with varying composition reveals that a nominal cobalt-palladium atomic ratio of 1:3, CoPd₃, exhibits the best performance of all studied catalysts, exhibiting a catalytic activity comparable to the commercial Pt catalyst. The ORR on CoPd₃ has a low activation energy, 52 kJ/mol, and a Tafel slope of approximately 60 mV/decade, indicating that the rate-determining step is a chemical step following the first electron transfer step and may involve the breaking of the oxygen bond. The CoPd₃ catalyst also exhibits excellent chemical stability, with the open circuit cell voltage decreasing by only 3% and the observed current decreasing by only 10% at 0.8 V over 25 h. The CoPd₃ catalyst also exhibits superior tolerance to methanol crossover poisoning than Pt.     

A novel sintering resistant and corrosion resistant Pt4ZrO2/C catalyst for high temperature PEMFCs

A novel Pt₄ZrO₂/C catalyst was prepared and compared with 20 wt.% Pt/C in terms of the sintering resistance and corrosion resistance. To evaluate their sintering resistance and corrosion resistance properties, an accelerated ageing test (AAT) was performed. The catalysts before and after AAT were characterized by cyclic voltammetry (CV), rotating disk electrode (RDE) and X-ray diffraction (XRD). After AAT, the dissolution rate of Pt and Zr in H₃PO₄ media (105 wt.%, 204 °C) was characterized by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The electrochemical area (ECA) changes of thin film electrodes based on Pt₄ZrO₂/C and Pt/C catalysts were also evaluated using continuous CV sweep technique. All the results showed that Pt₄ZrO₂/C has higher sintering resistance and corrosion resistance than Pt/C. ‘Anchor effect’ is proposed to explain the enhanced effect of ZrO₂ in Pt₄ZrO₂/C binary catalyst compared with Pt/C that contain platinum alone.     

Preparation and oxygen reduction activity of stable RuSex/C catalyst with pyrite structure

Carbon supported RuSe_x (x = 0.35-2) catalysts of controlled stoichiometry and phase are synthesized via precipitating ruthenium nanoparticles on Vulcan XC-72R, then selenizing ruthenium with hydrogen annealing. The competition for Se between solid-state Ru selenization and volatile selenium hydride formation results in RuSe_x nanoparticles with the pyrite structure, the Ru hcp structure, or a mixture of the two. These catalysts are methanol tolerant, and catalytically active toward oxygen reduction reaction (ORR). RuSe_x/C (x ≅ 2) with a pyrite structure, produced at 400 °C, exhibits catalytic activity and stability superior to that of RuSe_x/C with a ruthenium hcp structure or a mixed phase. And this pyrite RuSe_x/C (x ≅ 2) catalyst yields H₂O₂ less than 1.5% in the technically pertinent potential range of 0.4-0.6 V (vs. Ag/AgCl). Its stability is verified in 100 CV cycles, which shows that the catalyst annealed at 400 °C is more enduring in potential cycling over 0.65 V (vs. Ag/AgCl), compared with the RuSe_x/C catalyst annealed at 300 °C and the RuSe_cluster/C reference catalyst prepared by thermolysis of Ru₃(CO)₁₂. After CV cycles, the 400 °C-annealed catalyst still exhibits a higher ORR activity than the other two catalysts.     

High-surface-area CoTMPP/C synthesized by ultrasonic spray pyrolysis for PEM fuel cell electrocatalysts

Ultrasonic spray pyrolysis (USP) was used to synthesize a high-surface-area CoTMPP/C catalyst for oxygen reduction reaction (ORR). SEM micrographs showed that the USP-derived CoTMPP/C consists of spherical, porous and uniform particles with a diameter of 2-5 μm, which is superior to that with a random morphology and large particle sizes (up to 100 μm) synthesized by the conventional heat-treatment method. BET results revealed that the USP-derived catalyst had a higher specific surface area (834 m² g⁻¹) than the conventional one. Cyclic voltammetric, rotating ring-disk electrode (RRDE) and H₂-air PEM fuel cell testing were employed to evaluate the USP-derived CoTMPP/C. The kinetic current density of the USP-derived catalyst at 0.7 V versus NHE was two times higher than that of the conventional catalyst. Compared to Pt/C catalyst, the USP-derived CoTMPP/C catalyst showed a strong methanol tolerance and a higher ORR activity in the presence of methanol. In a H₂-air PEM fuel cell with USP-derived CoTMPP/C as the cathode catalyst, the cell performance was much higher than that with conventional heat-treated CoTMMP/C as the catalyst.     

Study of Methanol‐tolerant Oxygen Reduction Reaction at Pt–Bi/C Bimetallic Nanostructured Catalysts

The nanostructured platinum–bismuth catalysts supported on carbon (Pt₃Bi/C, PtBi/C and PtBi₃/C) were synthesised by reducing the aqueous metal ions using sodium borohydride (NaBH₄) in presence of a microemulsion. The amount of metal loading on carbon support was found to be 10 wt.‐%. The catalyst materials were characterised by X‐ray diffraction (XRD), X‐ray fluorescence (XRF), transmission electron microscope (TEM) and electroanalytical techniques. The Pt₃Bi/C, PtBi/C and PtBi₃/C catalysts showed higher methanol tolerance, catalytic activity for oxygen reduction reaction (ORR) than Pt/C of same metal loading. The electrochemical stability of these nano‐sized catalyst materials for methanol tolerance was investigated by repetitive cycling in the potential range of –250 to 150 mV_MSE. Bi presents an interesting system to have a control over the activity of the surface for MOR and ORR. All Pt–Bi/C catalysts exhibited higher mass activities for oxygen reduction (1–1.5 times) than Pt/C. It was found that PtBi/C catalyst exhibits better methanol‐tolerance than the other catalysts.     

Pt decorating of PdNi/C as electrocatalysts for oxygen reduction

A low-cost and high performance catalyst consisting of Pt decorating PdNi/C (Pt-PdNi/C) for oxygen reduction is prepared by a two-stage route. The characterization techniques considered are X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDX) technique. The results show that the Pt-PdNi/C catalyst has an average diameter of ca. 5 nm. The electrochemical activity for the ORR is evaluated from steady state polarization measurements, which are carried out in an ultra-thin layer rotating disk electrode (RDE). The RDE tests show that the Pt-PdNi/C catalyst has the highest ORR activity compared to pure Pt/C, Pd/C and PdNi/C catalysts. High electrocatalytic activities could be attributed to the synergistic effect between Pt and PdNi.     

Methanol-tolerant PdPt/C alloy catalyst for oxygen electro-reduction reaction

A carbon-supported Pd-based PdPt catalyst (PdPt/C) with a small amount of Pt was prepared by borohydride reduction method and its activity in the oxygen electro-reduction reaction (ORR) was investigated in acidic conditions both with and without methanol. For comparison, carbon-supported Pt (Pt/C) and Pd (Pd/C) catalysts were prepared and the ORR activities were compared. Results revealed that the PdPt/C catalyst showed slightly lower ORR activity in terms of onset potential of oxygen reduction than Pt/C catalyst in 0.1M HClO₄. However, PdPt/C catalyst exhibited enhanced activity toward selective ORR with methanol-tolerant characteristics in 0.1M HClO₄ in the presence of methanol. The PdPt/C catalyst prepared here is suitable for use as a cathodic electrocatalyst in direct alcohol fuel cells after addition of small amount of expensive Pt metal.     

Properties of Pt/C catalyst modified by chemical vapor deposition of Cr as a cathode of phosphoric acid fuel cell

Cr-modified Pt/C catalysts were prepared by the chemical vapour deposition (CVD) of Cr on Pt/C, and their performance as a cathode of phosphoric acid fuel cell (PAFC) was compared with the case of catalysts containing Cr added by impregnation (IMP).The catalyst prepared by CVD showed a higher activity for oxygen reduction reaction (ORR) than one prepared by IMP. There was an optimum amount of Cr that yielded the maximum mass activity of the catalyst because the gain in the intrinsic activity due to the promotional effect of Cr was counterbalanced by the loss of exposed Pt surface area as a result of the Cr introduction. Nevertheless, the activity increase at the optimum amount of Cr was greater for the CVD catalyst than for the IMP catalyst. Also, the optimum amount of Cr to yield the maximum activity was smaller for the former catalyst [Cr/Pt]_CVD = 0.6, than for the latter, [Cr/Pt]_IMP = 1.0.The enhancement of the Pt catalyst activity by Cr addition is attributed to two factors: changes in the surface Pt-Pt spacing and the electronic modification of the Pt surface. The formation of a Pt-Cr alloy, as confirmed by X-ray diffraction, decreased the lattice parameter of Pt, which was beneficial to the catalyst activity for ORR. X-ray photoelectron spectroscopy results showed that the binding energies of Pt electrons were shifted to higher energies due to Cr modification. Accordingly, the electron density of Pt was lowered and the Pt-O bond became weak on the Cr-modified catalysts, which was also beneficial to the catalyst activity for ORR.The promotion of oxygen reduction on Cr-modified catalysts was confirmed by measuring the cyclic voltammograms of the catalysts. All the above changes were made more effectively for catalysts prepared by CVD than for those prepared by IMP because the former method allowed Cr to interact more closely with the Pt surface than the latter, which was demonstrated by the characterization of catalysts in this study.     

Activity,selectivity, and methanol tolerance of novel carbon-supported Pt and Pt<Subscript>3</Subscript>Me (Me = Ni,Co) cathode catalysts

The activity, selectivity, and methanol tolerance of novel, carbon supported high-metal loading (40 wt.%) Pt/C and Pt₃Me/C (Me = Ni, Co) catalysts for the O₂ reduction reaction (ORR) were evaluated in model studies under defined mass transport and diffusion conditions, by rotating (ring) disk and by differential electrochemical mass spectrometry. The catalysts were synthesized by the organometallic route, via deposition of pre-formed Pt and Pt₃Me pre-cursors followed by their decomposition into metal nanoparticles. Characteristic properties such as particle sizes, particle composition and phase formation, and active surface area, were determined by transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. For comparison, commercial Pt/C catalysts (20 and 40 wt.%, E-Tek, Somerset, NJ, USA) were investigated as well, allowing to evaluate Pt loading effects and, by comparison with the pre-cursor-based catalyst with their much smaller particle sizes (1.7 nm diameter), also particle size effects. Kinetic parameters for the ORR were evaluated; the ORR activities of the bimetallic catalysts and of the synthesized Pt/C catalyst were comparable and similar to that of the high-loading commercial Pt/C catalyst; at typical cathode operation potentials H₂O₂ formation is negligible for the synthesized catalysts. Due to their lower methanol oxidation activity the bimetallic catalysts show an improved methanol tolerance compared to the commercial Pt/C catalysts. The results indicate that the use of very small particle sizes is a possible way to achieve reasonably good ORR activities at an improved methanol tolerance at DMFC cathode relevant conditions.     

Kinetics and PEMFC performance of RuxMoySez nanoparticles as a cathode catalyst

Kinetics of Ru_xMo_ySe_z nanoparticles dispersed on carbon powder was studied in 0.5 M H₂SO₄ electrolyte towards the oxygen reduction reaction (ORR) and as cathode catalysts for a proton exchange membrane fuel cell (PEMFC). Ru_xMo_ySe_z catalyst was synthesized by decarbonylation of transition-metal carbonyl compounds for 3 h in organic solvent. The powder was characterized by X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. Catalyst is composed of uniform agglomerates of nanocrystalline particles with an estimated composition of Ru₆Mo₁Se₃, embedded in an amorphous phase. The electrochemical activity was studied by rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE) techniques. Tafel slopes for the ORR remain invariant with temperature at −0.116 V dec⁻¹ with an increase of the charge transfer coefficient in dα/dT = 1.6 × 10⁻³, attributed to an entropy turnover contribution to the electrocatalytic reaction. The effect of temperature on the ORR kinetics was analyzed resulting in an apparent activation energy of 45.6 ± 0.5 kJ mol⁻¹. The catalyst generates less than 2.5% hydrogen peroxide during oxygen reduction. The Ru_xMo_ySe_z nanoparticles dispersed on a carbon powder were tested as cathode electrocatalyst in a single fuel cell. The membrane-electrode assembly (MEA), included Nafion^® 112 as polymer electrolyte membrane and commercial carbon supported Pt (10 wt%Pt/C-Etek) as anode catalyst. It was found that the maximum performance achieved for the electro-reduction of oxygen was with a loading of 1.0 mg cm⁻² Ru_xMo_ySe_z 20 wt%/C, arriving to a power density of 240 mW cm⁻² at 0.3 V and 80 °C.     

Oxygen electrocatalysis on ultra-thin porous coating rotating ring/disk platinum and platinum-cobalt electrodes in alkaline media

This work discusses the electrocatalysis of the oxygen reduction reaction (ORR) in alkaline media on ultra-thin porous coating electrodes formed by Pt and Pt-Co particles dispersed on carbon (Pt/C and Pt-Co/C, 1:1, 1:3, 1:5, 1:8 Pt:Co atomic proportion). XANES (X-ray absorption near edge structure) analysis was carried out in situ to examine the electronic properties of the Pt and Co atoms. X-ray diffraction was employed to estimate the catalyst particle size and to characterize the crystalline structure. The electrochemical techniques considered were cyclic voltammetry and steady state polarization, which were made using the standard rotating ring/disk electrode. Values of the kinetic parameters of the ORR obtained at the lower Pt/C ratios indicated participation of carbon in the catalysis of the reaction, leading to the formation of large amounts of HO₂⁻. At low overpotentials, the catalytic activity per mass of Pt obtained from mass-transport corrected Tafel plots for the 20 wt.% Pt-Co/C materials with lower Co contents are close that of the standard 20 wt.% Pt/C catalyst.     

Kinetics and electrocatalytic activity of nanostructured Ir-V/C for oxygen reduction reaction

Active, carbon-supported Ir-V nanoparticle catalysts have been synthesized by an ethylene glycol reduction method under controlled conditions at pH 10-13 and 120 °C, then further reduced at elevated temperature from 150 to 500 °C using IrCl₃ and NH₄VO₃ as the Ir and V precursors. The nanostructured catalysts have been characterized by X-ray diffraction (XRD) and high-resolution transmission electron microscopy (TEM). Ir nanoparticles, after modification with V, show a narrow particle size distribution in the range 0.5-4.5 nm, centered at 1.8 nm, and are uniformly dispersed on Vulcan XC-72. No particle agglomeration was observed, not even at high V loadings (V:Ir = 4:1 in atomic ratio). Investigation of the catalytic activity of the Ir-V/C by means of cyclic voltammetry (CV) and linear sweep voltammetry (LSV) employing a rotating disk electrode (RDE) has revealed that the presence of V may suppress the electrochemical oxidation of Ir and stabilize the Ir active centers. About six times higher kinetic current density was obtained for Ir-V/C compared to that of the pure Ir/C catalyst at 0.8 V versus RHE for the oxygen reduction reaction (ORR). The ORR in acid solution proceeds by an approximately four-electron pathway, through which molecular oxygen is directly reduced to water. The performance of a membrane electrode assembly (MEA) prepared with the most active 40% Ir-10% V/C as the cathode catalyst in a single proton-exchange membrane fuel cell (PEMFC) generated a maximum power density of 517 mW cm⁻² at 0.431 V and 70 °C, and 100 h of stable cell operation due to no loss of catalyst sites on the cathode.     

The improved methanol tolerance using Pt/C in cathode of direct methanol fuel cell

Membrane electrode assemblies (MEA) were prepared using PtRu black and 60 wt.% carbon-supported platinum (Pt/C) as their anode and cathode catalysts, respectively. The cathode catalyst layers were fabricated using various amounts of Pt (0.5 mg cm⁻², 1.0 mg cm⁻², 2.0 mg cm⁻², and 3.0 mg cm⁻²). To study the effect of carbon support on performance, a MEA in which Pt black was used as the cathode catalyst was fabricated. In addition, the effect of methanol crossover on the Pt/C on the cathode side of a direct methanol fuel cell (DMFC) was investigated. The performance of the single cell that used Pt/C as the cathode catalyst was higher than single cell that used Pt black and this result was pronounced when highly concentrated methanol (above 2.0 M) was used as the fuel.     

Porous-microelectrode study on Pt/C catalysts for methanol electrooxidation

We have developed a porous-microelectrode (PME) to investigate the electroactivity of catalyst particles for proton exchange membrane fuel cells. The cavity at the tip of the PME was filled with Pt/C catalysts prepared by impregnation method. Cyclic voltammograms (CVs) recorded in 1 N H₂SO₄ aqueous solution revealed that the active area of the stacked catalysts exist not only at the surface but also inside of the stack. For methanol electrooxidation, 30 wt.% Pt/C exhibited the highest electroactivity, whereas the 50 wt.% Pt/C showed extremely small current. The small current is considered as a result of a small active-surface area. Methanol oxidation peak potential shifted toward cathodic direction as Pt-loading decreased, which agrees well with the Pt-oxide formation potential. The activation energy for methanol oxidation was assessed to be 44±3 kJ mol⁻¹ for all Pt/C catalysts and Pt-disc electrode.