High rate performance of highly dispersed C60 on activated carbon capacitor

Fullerene-activated carbon composite electrodes were prepared and their charge/discharge characteristics were studied for use in a high power electric double-layer capacitor. The capacitance of the C₆₀-loaded activated carbon fiber (ACF) electrodes became greater than that of the unloaded ACF at charge/discharge current densities above 50 mA/cm². In order to obtain a highly dispersed C₆₀-loaded electrode, an ultrasonic treatment was performed. The size of the C₆₀ agglomerate decreased from 1-2 to 0.1 μm or less, and the capacitance of the C₆₀-loaded ACF electrodes increased with an increase in the ultrasonic treatment time. A higher capacitance of 172 F/g was obtained at 50 mA/cm² on a 1 wt% C₆₀-loaded electrode with ultrasonic treatment, and the C₆₀-loaded ACF electrode also showed a higher cycle performance.     

Evaluation of the pseudocapacitance in RuO2 with a RuO2/GC thin film electrode

The pseudocapacitance of nanocrystalline RuO₂ with BET surface area of 42 m² g⁻¹ was evaluated using a RuO₂ modified Glassy Carbon (RuO₂/GC) thin film electrode. The charge storage behavior of the RuO₂/GC thin film electrode was studied from fast to slow scan cyclic voltammetry between various potential windows. The utilization of the thin film electrode method for nanocrystalline RuO₂ with known specific surface area allowed a semi-quantitative understanding of the electric double-layer capacitance (C_dl), adsorption related charge (C_ad), and the irreversible redox related charge (C_irr) per unit mass and surface area of RuO₂. Comparison of the cyclic voltammograms between different voltage windows revealed that the contribution from C_irr is especially dominant below 0.4 V (versus RHE) at slow scan rates.     

Improvement in the capacitance of a carbon electrode prepared using water-soluble polymer binder for a capacitive deionization application

It is very important to increase the wetted surface area of a carbon electrode for high capacitive deionization performance. To increase the wettability of a carbon electrode, we fabricated carbon electrodes by using water-soluble polymer binder, polyvinyl alcohol (PVA). The electrochemical properties of the PVA-bonded carbon electrode were compared with another that was prepared using hydrophobic binder, polyvinylidene fluoride (PVdF). Electrochemical methods - cyclic voltammetry, chronoamperometry, and electrical impedance spectroscopy - were used to characterize the electrochemical properties of the electrodes. As might be expected, it was confirmed that the PVA-bonded electrode was more wettable than the PVdF-bonded one, based on contact angle measurements. From the cyclic voltammetric analysis, we found that the specific capacitance was 74.4-80.3 Fg⁻¹ for the PVdF-bonded electrode and 89.6-99.8 Fg⁻¹ for the PVA-bonded electrode, depending on the potential, indicating a 13.3-30.1% increase in specific capacitance. It was observed that the ac-signal penetrated micropores of the PVA-bonded carbon electrode more deeply than the PVdF-bonded one, resulting in a higher capacitance. This was attributed to the fact that the ac-signal was able to charge more inner surface sites because micropores in the PVA-bonded electrode could be wetted due to the PVA binder.     

Redox poly[Ni(saldMp)] modified activated carbon electrode in electrochemical supercapacitors

The complex (2,2-dimethyl-1,3-propanediaminebis(salicylideneaminato))-nickel(II), [Ni(saldMp)], was oxidatively electropolymerized on activated carbon (AC) electrode in acetonitrile solution. The poly[Ni(saldMp)] presented an incomplete coated film on the surface of carbon particles of AC electrode by field emission scanning electron microscopy. The electrochemical behaviors of poly[Ni(saldMp)] modified activated carbon (PAC) electrode were evaluated in different potential ranges by cyclic voltammetry. Counterions and solvent swelling mainly occurred up to 0.6 V for PAC electrode by the comparison of D^1/2C values calculated from chronoamperometry experiments. Both the Ohmic resistance and Faraday resistance of PAC electrode gradually approached to those of AC electrode when its potential was ranging from 1.2 V to 0.0 V. Galvanostatic charge/discharge experiments indicated that both the specific capacitance and energy density were effectively improved by the reversible redox reaction of poly[Ni(saldMp)] film under the high current density up to 10 mA cm⁻² for AC electrode. The specific capacitance of PAC electrode decreased during the first 50 cycles but thereafter it remained constant for the next 200 cycles. This study showed the redox polymer may be an attractive material in supercapacitors.     

Poly-o-phenylenediamine as redox mediator for laccase

Electrocatalytic activity towards oxygen reduction of fungal laccase entrapped in poly-o-phenylenediamine (POPDA) matrix on glassy carbon electrodes was studied. Cyclic voltammetry and amperometric responses to dissolved oxygen were investigated in pH range from 2 to 6. POPDA reveals a unique ability to serve as a redox mediator for laccase and immobilizing matrix at the same time. The entrapped enzyme efficiently catalyzes reduction of molecular oxygen without any additional mediators. The electrocatalytic current reaches 0.1 mA/cm⁻² per 1 μg of immobilized enzyme on cyclic voltammograms recorded at 1 mV/s in a not stirred electrolyte. Current density values are comparable with those revealed by dissolved laccase (60 μg/ml) mediated by hydroquinone and greatly higher than by the mediator less laccase/glassy carbon system. The potential of oxygen reduction is determined by the polymer redox couple. Consequently, the onset of the oxygen reduction shifts from −0.15 V versus Ag/AgCl in pH 6 to +0.05 V versus Ag/AgCl in pH 2. The laccase-POPDA layers immersed in the deaerated solution show fast amperometric responses to addition of the oxygen containing solution. The observed current values depend linearly on the oxygen concentration. Factors affecting the electrocatalytic activity of the laccase-POPDA system, including the layer thickness and the pH value, are studied. The electrodeposited laccase-POPDA films are characterized by infrared spectra. The results prove that the enzyme secondary structure remains unchanged during the entrapment procedure. POPDA matrix structure consists of the phenazine-type polymer according to infrared spectra.     

Theory of linear sweep/cyclic voltammetry for the electrochemical reaction mechanism involving a redox catalyst couple attached to a spherical electrode

The catalytic mechanism O_ad + ne⁻ ? R_ad, , involving a redox couple (O_ad, R_ad) attached to the electrode, and soluble species (C_sol, D_sol), is a precursor for many contemporary electrocatalytic reaction models. The theory of cyclic voltammetry for this mechanism was presented long ago for planar electrodes. Analogous rigorous theory for spherical electrodes has not been available thus far, despite the fact that the use of spherical microelectrodes for kinetic studies is often advantageous. By adopting the integral equation formalism, combined with the recently developed adaptive Huber method for integral equations, we obtain such a rigorous theory. The theory is applicable for any value of the electrode radius r₀, from planar electrodes (r₀ → ∞), to ultramicroelectrodes (r₀ → 0). With the decreasing electrode radii the current functions increase, gradually approaching steady-state sigmoidal waves. Equations for the dependences of the forward peak potentials on dimensionless model parameters, and equations for steady-state voltammograms, obtained in this work, can be used for model verification and parameter estimation.     

Monte Carlo study of the electrode|solvent primitive model electrolyte interface

Results of a Monte Carlo simulation of the electrode|electrolyte interface with and without solvent molecules are reported. The solvent molecules are modelled by neutral hard spheres immersed in a homogeneous dielectric medium. Calculations have been performed for 1:1 and 1:2 electrolytes at c = 1 M, with packing fraction η = 0.3 when the solvent molecules were present, and at a wide range of electrode charge. Insertion of the solvent molecules induces a layering of ion and solvent molecules in the vicinity of the electrode surface. The presence of the solvent molecules reduces the thickness of the electric double layer, lowers the value of the mean electrostatic potential and raises capacitance. The differential capacitance results are compared with the MPB theory predictions.     

Electrochemical characterization of screen-printed and conventional carbon paste electrodes

This work compares the electroactivity of a conventional carbon paste electrode and non-pretreated commercially available screen-printed carbon electrodes (from Alderon Biosciences, University of Florence and DropSens) towards some benchmark redox couples like hexaammineruthenium (III), ferricyanide, p-aminophenol and hydroquinone. While cyclic voltammograms of Ru³⁺ did not show significative electron transfer reactivity differences between the electrodes tested, the other redox systems exhibited higher reversible behaviours on DropSens electrodes. Scanning electron microscopy and roughness analysis with a profilometer were applied to detect the surface morphology of the working electrodes. The roughness evaluated of the screen-printed carbon working electrodes increased in this order Alderon < University of Florence < DropSens. Finally, the most electrochemically active and rough unpretreated electrode (DropSens commercial screen-printed electrode) was used to study the electrochemical-chemical reaction mechanism of indigo carmine oxidation in 0.1 M sulphuric acid. This study showed that the adsorption of the oxidation product of indigo carmine is stabilized when it is adsorbed on the surface of the electrode.     

Electropolymerization of phenol, o-nitrophenol and o-methoxyphenol on gold and carbon steel materials and their corrosion protection effects

This paper reports the results of a comparative study of the electropolymerization of phenol, o-methoxyphenol and o-nitrophenol by cyclic voltammetry on gold and carbon steel electrodes. The aim of this work is to synthesize homogeneous and adherent polyphenols film to protect carbon steel material against corrosion. Gold electrodes were used to optimize the experimental parameters such as the initial concentration of the monomer, the pH, the potential scan rate and the anodic potential limit value. Results showed that poly-o-metoxyphenol synthesized on carbon steel using optimized parameters obtained from gold electrode leads to more effective protection. This is probably due to the electron-donating mesomeric effet (+M) of the methoxy group which stabilized the phenoxy radicals obtained during the monoelectronic discharge of o-methoxyphenol. The best electropolymerization conditions involved an aqueous solution of 0.04 M o-methoxyphenol at pH 10.7, 5 mV s⁻¹ potential scan rate and an anodic potential limit (1.64 V/SCE) avoiding the degradation of the polymer film. The application of these conditions on steel electrodes leads to the formation of a stable, adherent and inhomogeneous film of polymer. A polymerization mechanism was proposed with consideration of results from literature.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

Poly(o-aminophenol) film prepared in the presence of sodium dodecyl sulfate: Application for nickel ion dispersion and the electrocatalytic oxidation of methanol and ethylene glycol

Poly(o-aminophenol) (POAP) was formed by successive cyclic voltammetry in monomer solution in the presence of sodium dodecyl sulfate (SDS) on the surface of a carbon paste electrode. The electrochemical behavior of the SDS-POAP carbon paste electrode has been investigated by cyclic voltammetry in 0.5 M HClO₄ and 5 mM K₄[Fe(CN)₆]/0.1 M KCl solutions as the supporting electrolyte and model system, respectively. Ni(II) ions were incorporated into the electrode by immersion of the polymeric modified electrode having amine groups in 0.1 M Ni(II) ion solution. Cyclic voltammetric and chronoamperometric experiments were used for the electrochemical study of this modified electrode. A good redox behavior of the Ni(III)/Ni(II) couple at the surface of electrode can be observed. The electrocatalytic oxidations of methanol and ethylene glycol (EG) at the surface of the Ni/SDS-POAP electrode were studied in a 0.1 M NaOH solution. Compared to bare carbon paste and POAP-modified carbon paste electrodes, the SDS-POAP electrode significantly enhanced the catalytic efficiency of Ni ions for methanol oxidation. Finally, using a chronoamperometric method, the catalytic rate constants (k) for methanol and ethylene glycol were found to be 2.04 × 10⁵ and 1.05 × 10⁷ cm³ mol⁻¹ s⁻¹, respectively.     

Electrochemical evaluation of avidin-biotin interaction on self-assembled gold electrodes

The avidin-biotin interaction on 11-mercaptoundecanoic acid self-assembled gold electrodes was investigated by means of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The interfacial properties of the modified electrodes were evaluated in the presence of the Fe(CN)₆^3−/4− couple redox as a probe. A simple equivalent circuit model with a constant phase element was used to interpret the obtained impedance spectra. The results of cyclic voltammetry showed that the voltammetric behavior of the redox probe was influenced by the electrode surface modification. It is evident that the accumulation of treated substances and the binding of biotin to avidin on the electrode surface resulted in the increasing electron-transfer resistance and the decreasing capacitance. The changes in the electron-transfer resistance on the avidin-modified electrodes were more sensitive than that in the capacitance while detecting biotin over the 2-10 μg/mL concentration. The detection amount can be as low as 20 ng/mL based on the electron-transfer resistance that presented the change of 4.3 kΩ without the use of labels. The development of a rapid, facile, and sensitive method for the quantitation of nanogram quantities of biomolecules utilizing EIS may be achieved.     

Preparation and electrochemistry of cadmium pentacyanonitrosylferrate film modified glassy carbon electrode

A glassy carbon (GC) electrode surface was modified with a cadmium pentacyanonitrosylferrate (CdPCNF) film as a novel electrode material. The modification procedure of the GC surface includes two consecutive procedures: (i) the electrodeposition of metallic cadmium on the GC electrode surface from a CdCl₂ solution and (ii) the chemical transformation of the deposited cadmium to the CdPCNF films in 0.05 M Na₂[Fe(CN)₅NO] + 0.5 M KNO₃ solution. The modified GC electrode showed a well-defined redox couple due to [Cd^IIFe^III/II(CN)₅NO]^0/−1 system. The effects of supporting electrolytes and solution pH were studied on the electrochemical behavior of the modified electrode. The diffusion coefficients of alkali-metal cations in the film (D), the transfer coefficient (α) and the charge transfer rate constant at the modifying film | electrode interface (k_s), were calculated in the presence of various alkali-metal cations. The stability of the modified electrode was investigated under various experimental conditions.     

Investigation on the electrode process of the Mn(II)/Mn(III) couple in redox flow battery

The Mn(II)/Mn(III) couple has been recognized as a potential anode for redox flow batteries to take the place of the V(IV)/V(V) in all-vanadium redox battery (VRB) and the Br₂/Br⁻ in sodium polysulfide/bromine (PSB) because it has higher standard electrode potential. In this study, the electrochemical behavior of the Mn(II)/Mn(III) couple on carbon felt and spectral pure graphite were investigated by cyclic voltammetry, steady polarization curve, electrochemical impedance spectroscopy, transient potential-step experiment, X-ray diffraction and charge-discharge experiments. Results show that the Mn(III) disproportionation reaction phenomena is obvious on the carbon felt electrode while it is weak on the graphite electrode owing to its fewer active sites. The reaction mechanism on carbon felt was discussed in detail. The reversibility of Mn(II)/Mn(III) is best when the sulfuric acid concentration is 5 M on the graphite electrode. Performance of a RFB employing Mn(II)/Mn(III) couple as anolyte active species and V(III)/V(II) as catholyte ones was evaluated with constant-current charge-discharge tests. The average columbic efficiency is 69.4% and the voltage efficiency is 90.4% at a current density of 20 mA cm⁻². The whole energy efficiency is 62.7% close to that of the all-vanadium battery and the average discharge voltage is about 14% higher than that of an all-vanadium battery. The preliminary exploration shows that the Mn(II)/Mn(III) couple is electrochemically promising for redox flow battery.     

Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: Application to chlorate, bromate and iodate detection

In this study, multi-wall carbon nanotubes (MWCTs) is evaluated as a transducer, stabilizer and immobilization matrix for the construction of amperometric sensor based on iron-porphyrin. 5,10,15,20-Tetraphenyl-21H,23H-porphine iron(III) chloride (Fe(III)P) adsorbed on MWCNTs immobilized on the surface of glassy carbon electrode. Cyclic voltammograms of the Fe(III)P-incorporated-MWCNTs indicate a pair of well-defined and nearly reversible redox couple with surface confined characteristics at wide pH range (2-12). The surface coverage (Γ) and charge transfer rate constant (k_s) of Fe(III)P immobilized on MWCNTs were 7.68 × 10⁻⁹ mol cm⁻² and 1.8 s⁻¹, respectively, indicating high loading ability of MWCNTs for Fe(III)P and great facilitation of the electron transfer between Fe(III)P and carbon nanotubes immobilized on the electrode surface. Modified electrodes exhibit excellent electrocatalytic activity toward reduction of ClO₃⁻, IO₃⁻ and BrO₃⁻ in acidic solutions. The catalytic rate constants for catalytic reduction of bromate, chlorate and iodate were 6.8 × 10³, 7.4 × 10³ and 4.8 × 10² M⁻¹ s⁻¹, respectively. The hydrodynamic amperometry of rotating-modified electrode at constant potential versus reference electrode was used for detection of bromate, chlorate and iodate. The detection limit, linear calibration range and sensitivity for chlorate, bromate and iodate detections were 0.5 μM, 2 μM to 1 mM, 8.4 nA/μM, 0.6 μM, 2 μM to 0.15 mM, 11 nA/μM, and 2.5 μM, 10 μM to 4 mM and 1.5 nA/μM, respectively. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantages of this sensor. The obtained results show promising practical application of the Fe(III)P-MWCNTs-modified electrode as an amperometric sensor for chlorate, iodate and bromate detections.     

Adsorption of ochratoxin A (OTA) anodic oxidation product on glassy carbon electrodes in highly acidic reaction media: Its thermodynamic and kinetics characterization

We study the thermodynamics and kinetics of the adsorption of a redox couple having quinone nature on glassy carbon electrodes. This couple is produced by the anodic oxidation of mycotoxin ochratoxin A in 10% acetonitrile + 90% 1 M HClO₄ aqueous solution. The quasi-reversible redox couple was studied by both cyclic (CV) and square wave (SWV) voltammetric techniques. The Frumkin adsorption isotherm best described the specific interaction of the redox couple with carbon electrodes. By fitting the experimental data, we obtained values of −28.4 kJ mol⁻¹ and 0.70 ± 0.02 for the Gibbs free energy of adsorption and the interaction parameter, respectively. SWV fully characterized the thermodynamics and kinetics of the adsorbed redox couple, using a combination of the “quasi-reversible maximum” and the “splitting of SW peaks” methods. Average values of 0.609 ± 0.003 V and 0.45 ± 0.06 were obtained for the formal potential and the anodic transfer coefficient, respectively. Moreover, a formal rate constant of 10.7 s⁻¹ was obtained. SWV was also employed to generate calibration curves. The lowest concentration of mycotoxin was 1.24 × 10⁻⁸ M (5 ppb), measured indirectly with a signal to noise ratio of 3:1.     

The electrochemical reduction of VO2 in acidic solution at high overpotentials

An investigation has been carried out to attempt to understand the unusually low apparent symmetry factor observed during the reduction of V(5) at higher overpotentials at carbon electrodes (typically <0.13, or >460 mV decade⁻¹). This reaction is of interest because it occurs in vanadium redox-flow batteries (VRBs) during discharge. Polarisation curves were measured using a rotating disk electrode (RDE). The reaction was not solution mass transport controlled, was pH independent (ca from 0 to 1), and the observed Tafel slope was unaffected by V(5) concentration over a range from 0.031 to 280 mM. Electrode double layer capacitance measurements were also carried out in sulphuric acid with and without vanadium. These tests showed that the presence of V(5) caused a suppression of the normal carbon surface quinone pseudocapacitance, as well as the appearance of two new pseudocapacitance peaks, one around 0.175-0.2 V and the other around 0.675-0.725 V versus SCE. The observed results do not appear consistent with a precipitated film causing diffusion limitations or causing IR drop. A model is developed to try to explain the data, which involves electron transfer through an adsorbed layer of vanadium.     

Highly hydroxylated carbon fibres as electrode materials of all-vanadium redox flow battery

A highly effective hydroxylated-functionalization of carbon fibres for use as electrodes of all-vanadium redox flow battery (VRFB) was developed. Carbon paper made of carbon fibres was hydroxylated ultrasonically with mixed acids (H₂SO₄/HNO₃, V_H2SO4/V_HNO3 = 3/1) in a Teflon-lined stainless steel autoclave for different time at 80 °C. The structure, composition, and electrochemical properties of the treated samples for positive and negative electrodes of VRFB were characterized with Fourier transformation infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectrometry, scanning electron microscopy, X-ray diffraction, cyclic voltammetry, electrochemical impedance spectroscopy, and cell charge and discharge tests. The content of hydroxyl group changes from 3.8% for the untreated sample to 14.3% for the carbon paper treated in mixed acids for 10 h. The highly hydroxylated sample shows its high activity toward the redox reactions of V(II)/V(III) and V(IV)/V(V). The VRFB using the carbon paper treated for 8 h as the electrodes exhibits excellent performance under a current density of 10 mA cm⁻². The average voltage efficiency reaches 91.3%, and the average energy efficiency reaches 75.1%. The mechanisms for the high hydroxylation of the carbon fibres with the mixed acids and the high activity of the treated sample toward the vanadium redoxs are discussed.     

Preparation and electrochemical investigation of the polyaniline/activated carbon nanocomposite for supercapacitor applications

The polyaniline (PANI)/activated carbon (AC) nanocomposite electrodes were prepared by electropolymerization of aniline monomers on the surface of AC/polyvinyl alcohol (PVA) electrodes for supercapacitor studies. Fourier transforms infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses were performed to characterize the structure and morphology of the nanocomposite electrodes. The electrochemical properties of the prepared nanocomposite electrodes and the supercapacitive behavior of the PANI, AC, and AC/PANI/PVA electrodes were investigated using cyclic voltammetry (CV) and galvanostatic charge/discharge measurements, respectively. Morphological studies showed that a thin film of PANI has been uniformly deposited on the porous surface of AC electrode, and an ordered arrangement of nanostructures with interlinked porous network has been made. Electrochemical measurements showed that AC particles prevent the degradation of PANI chains during charge/discharge cycles. The specific capacitance of the AC/PANI/PVA nanocomposite electrode was 338.15 F/g which is higher than that of the pristine AC electrode (0.08 F/g). This is due to the contribution of PANI chains by their pseudocapacitance (redox reaction) properties. Although the specific capacitance of PANI electrode (378.57 F/g) was greater than that of the nanocomposite electrode, the cyclic stability of the PANI electrode was lower than that of the AC/PANI/PVA nanocomposite electrode.     

Fabrication of nickel oxide-embedded titania nanotube array for redox capacitance application

Titania nanotube array with an enlarged tube diameter of 110 nm and length of 700 nm was grown on titanium metal by a potentiostatic anodization in hydrofluoric acid-phosphoric acid-ethenyl glycol electrolyte. Nickel hydroxide was introduced into this titania nanotubes by either an electrodeposition-oxidation or hydrothermal process. Nickel oxide-titania composite was finally formed by heating treatment at 300 °C. Such a well-defined nanocomposite supported on titanium substrate was designed as a functional nanotube array electrode for the redox capacitance application. The morphology, microstructure and electrochemical properties of the nanocomposites were investigated by field emission scanning electron microscope, X-ray diffraction, energy dispersive X-ray diffraction and cyclic voltammetry measurements. It was found that nickel oxide could be embedded in titania nanotubes and extend from inner wall to top layer with an open pore mouth. The entire tube lengths were approx. 770 nm and 710 nm, meanwhile nickel-to-titanium atom ratios were determined as 9.6 at% and 36.4 at% for nickel oxide-embedded titania by an electrochemical and hydrothermal synthesis, respectively. The corresponding specific redox capacitance was also increased from 26 mF cm⁻² to 85 mF cm⁻² with highly reversible charge-discharge stability. Such an improvement was mostly ascribed to more accessible reaction interface of electroactive nickel oxide through its higher loading and a uniform dispersion on titania nanotubes. The capacitance was further increased up to 128 mF cm⁻² for 36.4 at% nickel-containing nickel oxide-titania/titanium electrode when a porous graphite carbon instead of a platinum sheet was used as a cathode.