Total hip arthroplasty performed without cement in patients with femoral head osteonecrosis who are less than 50 years old

Seventy-two cementless total hip arthroplasties were performed by a single surgeon in 58 patients with the diagnosis of femoral head osteonecrosis. All patients were less than 50 years old (mean, 37 years). The mean follow-up was 84 months with a minimum of 48 months. Good-to-excellent results were maintained at final follow-up in 94% of the hips. Revision rate was 1.5% each for the cups and the stems. Mechanical failure rate was 7.6% for the cups, and 6% for the stems. If the results were analyzed excluding the data from the group of patients who received the Mittelmeier prostheses, the mechanical failure rates for the cups was 0% and for the stems was 4.2%. The probability of survival for the entire series using revision as the endpoint was 96.9% at 11 years. Survival probability decreased to 88.5% if radiographic failures were included. Excluding the Mittelmeier prostheses, survival probability was estimated to be 100% for the cups using both revision and radiographic failures as endpoints; for the stems, the survival probability was 98.0% using revision as the endpoint and 95.8% including radiographic failures. Femoral osteolysis was observed in 1.5% of the hips. No hip had acetabular osteolysis. No measurements of polyethylene wear were attempted in this study. These results appeared superior to total hip arthroplasties done with early cementing techniques in this population of young patients with femoral head osteonecrosis.     

Conjugation of 5-fluoro-2''-deoxyuridine with lactosaminated poly-l-lysine to reduce extrahepatic toxicity in the treatment of hepatocarcinomas

Numerous clinical results reported in the literature prove that ceramic femoral heads reduce wear, osteolysis, and revision rates in total hip replacements (THRs). Femoral heads and cups made out of alumina ceramics were introduced about 25 years ago, and femoral heads made out of zirconia were introduced about 10 years ago. Today, the wear couples of alumina-on-polyethylene or zirconia-on-polyethylene have become the standard in THR. The wear couple offering the lowest wear rate is alumina-on-alumina. This article discusses the state of the art and lists advantages as well as problems with the various materials used for prostheses in THR.     

Comparison of human, primate, and canine femora: implications for biomaterials testing in total hip replacement

The canine model remains an animal of choice for determining the efficacy and safety of various materials and designs used in human total hip replacement (THR). The primate also is used in orthopedic-related research for studying limb anatomy, gait, and age-related bone loss. In order to better understand the appropriateness of these animal models for human THR, external morphologies of thirty-three adult Caucasian human, sixteen adult chimpanzee, and forty-two adult greyhound femora were compared using osteometric methods. Measured parameters included anteversion angle, cervico-diaphyseal angle, femoral head offset in the frontal plane, and anterior bow profiles along the femoral diaphysis. Although some of the measured parameters were approximately similar between species (e.g., mean cervico-diaphyseal angle of humans and chimpanzees), the majority demonstrated morphologic differences that may be biomechanically significant for interpreting stress transfer across the hip (e.g., mean anteversion angle and mean normalized femoral head offset between species). Additionally, age-related changes in proximal femoral morphology and gait pattern, as well as species-related differences in local muscle and inertial forces, may result in notably different loading conditions across the hip joint of each species. Therefore, discretion must be exercised when evaluating canine or primate THR materials and designs for potential use in the human hip.     

Total hip arthroplasty with use of second-generation cementing techniques. An eighteen-year-average follow-up study

In this report, we present the results of a further follow-up of a series of 140 consecutive patients (161 hips) who had had a primary total hip arthroplasty with insertion of a bead-blasted monoblock femoral component with use of so-called second-generation cementing techniques. The average age of the patients at the time of the arthroplasty was sixty-one years (range, twenty-one to eighty-five years). Sixty-seven patients (seventy-seven hips) died less than seventeen years after the index operation. The remaining seventy-three patients (eighty-four hips) were followed for an average of eighteen years (range, seventeen to twenty years). No patient was lost to follow-up. In the entire group of 161 hips, over the twenty-year span of the study, eight femoral components (5 percent) and twenty-eight acetabular components (17 percent) had been revised because of aseptic loosening. Of the seventy-seven hips in the sixty-seven patients who died, four had been revised because of aseptic loosening of the acetabular component only; one, because of aseptic loosening of the femoral component only; and one, because of aseptic loosening of both components. Of the eighty-four hips in the seventy-three patients who were alive at least seventeen years after the index arthroplasty, twenty-four hips (29 percent) in twenty-one patients had had revision of one or both components for any reason. Twenty-three acetabular components (27 percent) and six femoral components (7 percent) had been revised because of aseptic loosening. An additional two hips (2 percent) in two patients were loose according to radiographic criteria but had not been revised. Of the sixty-five all-polyethylene acetabular components that had been inserted with cement and were in patients who were alive at least seventeen years postoperatively, fifteen (23 percent) had been revised because of aseptic loosening. An additional seventeen cups (26 percent) were loose according to radiographic criteria. Thus, a total of thirty-two cups (49 percent) had been revised because of loosening or were loose but had not been revised at the time of the latest follow-up. The femoral components that had been inserted with use of second-generation cementing techniques fared better than did the acetabular components that had been inserted with these techniques during the same time-period. We found that assessment of all postoperative radiographs rather than only those that had been made immediately postoperatively increased the accuracy of the grading of the cement around the femoral component. Subsequent radiographs frequently had been made at different projections, which revealed new findings, consisting primarily of previously undetected voids, areas of thin cement, and defects in the cement mantle. Thus, we now use all available radiographs to determine the grade of the cement.     

Survivorship analysis of cemented total hip arthroplasty acetabular components implanted with second-generation techniques

The clinical and radiographic results of primary cemented total hip arthroplasty performed by a single surgeon, with particular emphasis on the performance of acetabular components implanted with so-called second-generation cement techniques, were studied. Seventy hips with 48 metal-backed and 22 polyethylene acetabular components were followed for a mean of 9 years (range, 5-11.5 years). The clinical results were evaluated using a recognized hip score. The fixation status of the cemented acetabular component was evaluated using two methods of measuring radiolucent lines at 5 years and at the last evaluation. Acetabular component loosening was defined as a circumferential radiolucent line, component migration, or revision for loosening. This study was unable to confirm the findings of others that demonstrated higher failure rates with cemented metal-backed components when compared with all-polyethylene components. The survival of cemented acetabular components with 28-mm head femoral prostheses was worse than the survival of cemented acetabular components with 22-mm femoral heads in other published reports, despite advances in cement techniques. Because of the high rate of loosening of cemented 28-mm-inner-diameter acetabular components at 5 and 10 years, the authors no longer use these cemented components for acetabular reconstruction.     

Acetabular and femoral fixation 15 years after cemented total hip surgery

Total hip arthroplasty in patients younger than 51 years of age remains controversial. The authors report results in 47 hips in 40 patients at an average followup of 15 years. Second generation femoral cementing techniques were used. Special attention was given to studying the differences between the outcome of acetabular versus femoral fixation. The patient group included 11 in whom custom components were used and 13 who had structural autografts for severe acetabular dysplasia. One femoral component and 10 acetabular components were revised for aseptic loosening. After 15 years, improved cementing techniques produced a marked reduction in the rate of femoral aseptic loosening. Loss of fixation of cemented acetabular components was common.     

Effect of nitric oxide, prostacyclin, and thromboxane on the vasospastic action of hydrogen peroxide on human umbilical artery

During the years 1991-1994, the Norwegian Arthroplasty Register recorded 1,324 primary hip arthroplasties implanted with the Boneloc cement. We have compared the survival until revision due to aseptic loosening for charnley (n 955) and Exeter (n 172) prostheses. The Boneloc cemented hips were also compared with high viscosity cemented hips implanted during the same period. In the Boneloc cemented group, the estimated probability of survival at 4.5 years of a Charnley femoral component was 74% and for an Exeter femoral component 97% (p < 0.0001). Using a Cox regression model with adjustment for age, gender, type of cement, systemic antibiotic and stratified for diagnosis, an 8 times higher risk of revision was found in Boneloc cemented Charnley femoral components than in Exeter femoral components (p < 0.0001). For the acetabular components, the difference between the Charnley and Exeter components with Boneloc cement was not statistically significant. In both the Charnley and the Exeter prostheses, the high viscosity cemented components had significantly better survival than the Boneloc cemented components. The Cox regression model showed that a Boneloc cemented Charnley femoral component had a 14 times higher risk of revision than a high viscosity cemented component (p < 0.0001), and for Exeter femoral components a 7 times higher revision risk was found in the Boneloc cemented components (p = 0.003). Our results confirm the previously reported inferior results of Charnley prostheses implanted with Boneloc cement and inferior results of Boneloc cemented Exeter prostheses as well, but less pronounced than for Charnley prostheses.     

Development of bioactive bone cement and its clinical applications

This paper is a summary of already published papers on the bioactive bone cement (BA cement) which consists of CaO-SiO2-P2O5-MgO-CaF2 (AW glass-ceramic) powder and bisphenol-a-glycidyl methacrylate (Bis-GMA) resin. Two types of BA cement, dough and injection type, were prepared by changing their chemical compositions slightly. They harden in a few minutes exhibiting much lower curing temperature than PMMA cement. They have significantly higher compressive, bending, and tensile strengths than PMMA cement and have a character of bonding directly with bone in 4-8 weeks in vivo. Intercalary prosthetic replacement of the femur and total prosthetic replacement of the hip were performed in dogs using either PMMA cement or BA cement. Mechanical tests demonstrated that fixation strengths of these prostheses with BA cement increased with time and were significantly greater than those with PMMA cement tested at any time. Results of histological examinations showed direct bonding between BA cement and bone, and that the bone trabeculae around BA cement mantle grew with time, while with PMMA cement an intervening soft tissue layer was always observed at the cement-bone interface. BA cement was used in a few aged patients to install a hip prosthesis either in cases of revision or femoral neck fracture. The longest follow-up period of the patient is 4 yrs. The patients have been doing well with no adverse effect of the cement to date.     

Effect of improved cementing techniques on the longevity of fixation in revision cemented femoral arthroplasties. Average 8.8-year follow-up period

Forty-six revision cemented femoral arthroplasties in which second-generation cementing techniques were used have been reviewed. After an average follow-up period of 8.8 years, 91% of the femoral components remained in place and 87% remained well fixed. Only 7% were rerevised for aseptic loosening. These results demonstrate a marked improvement over those of first-generation cementing techniques.     

Factors influencing pressurization of the femoral canal during cemented total hip arthroplasty

Successful cement pressurization with total hip arthroplasty depends on the capacity of the cement gun and its ability to pressurize the canal and the integrity of the intramedullary plug and the proximal seal used to contain the cement bolus during pressurization. In the laboratory, the authors measured the volume of cement delivered by two cement guns (from Zimmer, Warsaw, IN, and Howmedica, Rutherford, NJ) in comparison with typical values for the volume of the medullary canal following standard surgical preparation. The two cement guns studied delivered 93 and 138 mL cement, respectively. In comparison, the volume of the intramedullary canal ranged from 35 to 70 mL using a standard femoral prosthesis (Precision Hip System, Howmedica). Peak pressures developed during cement injection using the cement guns were 73.6 +/- 27.1 psi for the Zimmer system and 47.3 +/- 16.9 psi for the Howmedica system. Both devices were able to sustain a minimum pressure of at least 6.5 psi through cementing when used in conjunction with a flexible pressurizing seal. The mechanical performance of five designs of intramedullary plugs was assessed by monitoring plug displacement during cement pressurization in reamed cortical specimens. The performance of each device was judged by its ability to withstand cement pressures of 50 psi without displacement within the medullary canal. On the basis of this test, the probability that these plugs would exceed this criterion when used with the femur was estimated to range from 24 to 94%. Few of the commercially available plugs were able to withstand cement pressures routinely generated using standard cement delivery systems.     

炼铅炉渣用于矿山充填胶凝剂的试验研究

在分析炼铅炉渣理化特性的基础上,通过外界条件激发铅渣潜在活性,将其作为胶凝材料应用于矿山充填替代部分或全部水泥,进行全尾砂膏体试验。试验采用全面试验法,试验结果表明,选用合适的激发剂及铅渣胶凝材料配方,铅渣胶凝材料替代部分水泥用于矿山井下充填可以满足矿山生产的强度要求。     

Proximal and distal femoral centralizers in modern cemented hip arthroplasty

Third generation cementing techniques using intramedullary restrictors, low porosity cement with pressurization, lavage, and cement-stem bond enhancement do not prevent implant malalignment and inadequate cement mantle thickness. This has led to the development of modular proximal and distal centralizers to control the alignment of the femoral component and maintain an adequate thickness of the cement, thereby theoretically decreasing the rate of aseptic loosening. A retrospective analysis was performed of 100 primary cemented centralized femoral components. At an average followup of 5.7 years (range, 4-8 years), the average Harris Hip Score was 90. There were no cases of aseptic loosening, osteolysis, or impending failure. Ninety-one percent of femoral stems were implanted with satisfactory alignment with an optimal cement thickness. However, six distal centralizers and one proximal centralizer fractured at the time of insertion and voids frequently were seen in and around the distal centralizer. Although centralizers improve prosthesis alignment and cement mantle thickness, the long term effects of centralizer fracture and distal cement voids need to be observed to determine if centralizers improve previous implant survival.     

Ceramic endoprosthesis in total hip arthroplasty

Aluminia-on-aluminia hip prosthesis with titanium alloy stem was used in 255 cases, for 143 patients with cemented acetabular cup and 112 with an uncemented screw cup. The average age of the patients was 62 years. Of the patients, 35 were treated bilaterally. The indication for surgery was osteoarthritis in 186 cases, fractures and nonunions of the hip joint in 34 cases, and congenital dislocations of the hip joint in 16 cases. Previous surgery of the hip joint was recorded for 43 cases. All procedures were primary arthroplasties. Only personal clinical examinations together with radiographic studies were accepted as clinical data. Three patients failed to show up for routine follow-up evaluation and these were excluded from the series. Revision operation was classified as failure. The indications for revision were aseptic loosening, late infection, and fracture of the acrylic cement resulting in loosening of the acetabular or femoral component. The acetabular component was cemented in 143 patients and the mean follow-up period for these patients was 6.7 years (range, 1-12 years). In this series, a revision operation was undertaken for 16 patients (11%). In 12 cases, broken acrylic cement resulted in acetabular aseptic loosening. In the series of 112 patients with uncemented titanium screw cup, the mean follow-up period was 3.6 years (range, 1-7 years) and a revision operation was undertaken in seven cases (7%). In two, the indication was late infection; in one, technical failure; and in two, progression of Pigmented villonodular synovitis. Acetabular aseptic loosening resulted in revision in only two cases. With cementless acetabular component bone transplantation is indicated.(ABSTRACT TRUNCATED AT 250 WORDS)     

Autocrine regulation of keratinocytes: the emerging role of heparin-binding, epidermal growth factor-related growth factors

Two hundred and ninety-seven consecutive Charnley total hip replacements that had been followed for at least twenty years or until revision or death were analyzed to determine the effect of early debonding of the smooth-surfaced femoral component on its subsequent survival. Radiographically evident debonding was not found to have a significant effect, with the numbers available, on the long-term survival of the femoral component when the maximum thickness of the radiolucent line between the superolateral border of the prosthesis and the cement had been less than 2.0 millimeters during the first one to five years after the operation. The radiographic finding of debonding also was not found to be associated with pain in the hip. These data show that most components with early debonding functioned well during a long period of follow-up and suggest that debonding of a smooth femoral component of a Charnley total hip replacement should not be considered to be analogous to loosening. In contrast, when the maximum thickness of the radiolucent line between the superolateral border of the prosthesis and the cement was 2.0 millimeters or more, an early appearance of debonding was associated with a significantly poorer (p < 0.0001) probability of survival of the Charnley femoral component without revision because of aseptic loosening. Thus, pronounced early subsidence of the component within the cement mantle had a strong negative impact on the long-term performance of the implant. The results of the present study should not be extrapolated to prostheses with substantially different design characteristics, as it appears that different types of femoral components behave differently when debonding occurs.     

Spatial differences in gap junction gating in the lens are a consequence of connexin cleavage

Thirty patients had 32 cementless total hip arthroplasty revisions and were evaluated postoperatively for clinical function (Harris Hip Score) and radiographic evidence of implant stability. Of the 26 femoral components revised, 16 were revised with anatomic long-stem femoral prostheses, and 10 were revised with straight mid-stem-length components. All components were collared and had circumferential proximal fiber-mesh porous coating. Seven of 16 patients had radiographic subsidence after revision with long-stem components (2 to 30 mm); 6 of 10 patients had subsidence after revision with mid-stem femoral components (2 to 25 mm). Of the 13 patients with femoral subsidence, 8 had calcar reconstruction with allograft bone; of the 13 patients without radiographic subsidence, 8 did not require calcar reconstruction. One of 27 fiber-mesh, porous-coated acetabular components migrated (30 mm). No components have been removed or revised. Even with circumferential proximal porous coating, femoral implant stability remains unpredictable in total hip arthroplasty revision.     

Cement-mantle thickness affects cement strains in total hip replacement

Bone cement is commonly used to affix femoral implants to the bone during total hip reconstruction. Previous studies suggest that the expected life of a cemented femoral implant may depend on the thickness of the cement mantle surrounding the implant and the implant geometry. The purpose of this study was to determine whether different cement-mantle thicknesses and femoral stem sizes affected strain patterns in the bone cement around cemented femoral stems. Two different sizes of cobalt-chromium stems were cemented into composite femora with varying cement-mantle thickness. Strain gages were embedded in the cement mantle and the implanted stems were loaded axially and under conditions simulating walking and standing. An increase in stem size with the same cement-mantle thickness (approximately 2.2 mm) caused a 65% decrease in proximal medial cement strains. Increasing cement mantle thickness from 2.4 to 3.7 mm caused substantial strain reductions in the distal cement (40-49%). We conclude that increased cement-mantle thickness around femoral stems may increase the fatigue life of a bone-implant system by reducing peak strains within the cement.     

Importance of a thin cement mantle. Autopsy studies of eight hips

The question whether thin cement mantles around cemented femoral components led to an increased frequency of cracks in the cement was asked. Microscopically, multiple cross sections of eight femurs retrieved at autopsy from clinically successful total hip replacements after prolonged in vivo service containing well fixed Harris Design 2 cemented femoral components were studied. None of the components were loose by radiographic criteria. All were fixed solidly when loaded in vitro in simulated stair climbing and gait, as assessed by high resolution micromotion sensors. The specimens were sectioned transversely at 5-mm increments. The cross sections were examined under a dissecting microscope at x 100. A thin mantle arbitrarily was defined as a mantle of less than 1 mm in thickness. The analysis of the contact radiographs showed that the routine anteroposterior and lateral radiographs underestimated the prevalence of thin cement mantles and mantle defects. Although overall on all the cross sections 9% of the aggregated cement mantles was classified as having thin cement, 92 of the 101 cement cracks occurred in areas of the mantles that were less than 1 mm thick.     

The value of preoperative planning for total hip arthroplasty

To analyse the value and accuracy of preoperative planning for total hip replacement (THR) we digitised electronically and compared the hand-sketched preoperative plans with the pre- and postoperative radiographs of 100 consecutive primary THRs. The correct type of prosthesis was planned in 98%; the agreement between planned and actually used components was 92% on the femoral side and 90% on the acetabular side. The mean (+/- SD) absolute difference between the planned and actual position of the centre of rotation of the hip was 2.5 +/- 1.1 mm vertically and 4.4 +/- 2.1 mm horizontally. On average, the inclination of the acetabular component differed by 7 +/- 2 degrees and anteversion by 9 +/- 3 degrees from the preoperative plans. The mean postoperative leg-length difference was 0.3 +/- 0.1 cm clinically and 0.2 +/- 0.1 cm radiologically. More than 80% of intraoperative difficulties were anticipated. Preoperative planning is of significant value for the successful performance of THR.     

Total hip replacements using the ceramic Mittelmeier prosthesis

One hundred twelve consecutive primary total hip replacements were performed for osteoarthritis or osteonecrosis by a single surgeon using the Mittelmeier ceramic prosthesis without cement between January 1983 and July 1984. Ninety-three of these hips were followed prospectively to a minimum of 60 months and a median of 108 months. Five (5.4%) hips have been revised for loosening. Of the remaining hips, 77 (87.5%) were rated clinically satisfactory. Cumulative survival probability using revision as endpoint was estimated to be 92.7% at 5 years and 87.9% at 10 years. However, overall mechanical failure rates were 21.5% for the cup and 22.6% for the stem. There was no case of either femoral or acetabular osteolysis observed.     

Purification and characterization of a cysteine protease produced by pathogenic luminous Vibrio harveyi

A histologic and biochemical comparison of interface membranes around femoral components of bipolar endoprostheses (n = 17) and total hip prostheses (n = 17) inserted without cement was conducted. The patients' profiles were similar in both groups with respect to age, sex, primary diagnosis, weight, and the interval between primary and revision arthroplasty. Macroscopically, marked circumferential abrasion of the polyethylene insert in the retrieved bipolar cups was noted. Histologic analysis revealed significantly larger amounts of polyethylene debris in the bipolar group. The membranes from the bipolar group also produced significantly greater amounts of prostaglandin E2 (P < .05). The inflammatory membranes associated with large amounts of polyethylene debris may have contributed to aseptic loosening and osteolysis in patients with a bipolar hip prosthesis.