基于钙基吸收剂吸收CO2的研究进展

综述了钙基吸收剂煅烧/碳酸化循环吸收CO2的国内外研究状况.从反应条件对碳酸化反应的影响、改善钙基吸收剂吸收CO2的性能、钙基吸收剂循环热稳定性的方法以及碳酸化反应动力学特性这4个方面进行分析,认为碳酸化反应主要分为化学反应控制和产物层扩散2个阶段,指出CO2分压和吸收剂的颗粒粒径决定着碳酸化反应温度和CO2的脱除效率...     

钙基吸收剂吸收CO_2的动力学分析

利用热天平在非等温条件下研究了在N2/CO2气氛下,升温速率、样品粒径及CO2浓度等因素对钙基吸收剂与CO2反应特性的影响,并利用活化能和频率因子进行表征。结果表明:在5种不同前体制备的吸收剂中,草酸钙和乙酸钙制备的钙基吸收剂的活化能最低,更容易与CO2发生反应;在其他条件相同的情况下,分析纯CaCO3制备的钙基吸收剂的活化能,随循环次数增加而逐渐变大,并且在第5次循环到第10次循环之间,活化能增加幅度较大;随着分析纯CaCO3颗粒粒径的增大,其活化能也随之增大;随着升温速率的增大和反应气氛中CO2质量分数的增大,分析纯CaCO3制备的钙基吸收剂的活化能逐渐减小,而频率因子逐渐增大;掺杂有MgO的碳酸钙制备的钙基吸收剂的活化能小于分析纯CaCO3,且MgO掺杂比例为0.05的钙基吸收剂的活化能小于MgO掺杂比例为0.1的钙基吸收剂。     

三元复合钙基材料CaO-Ca3Al2O6-MgO的合成及其CO2吸附性能

采用Al₂O₃和MgO同时掺杂改性的方法制备了CaO-Ca₃Al₂O₆-MgO复合钙基高温吸附CO₂材料。复合钙基材料孔隙发达,活性物相为CaO,惰性骨架物相为Ca₃Al₂O₆和MgO。Ca₃Al₂O₆/MgO质量比偏小的材料,表面微粒粒径较小。在10%（体积分数,下同）CO₂和90% N₂的混合气气氛下,采用热重分析仪测量了复合钙基材料吸附CO₂容量、碳化反应速率以及循环碳化（670℃）/煅烧（900℃）过程的稳定性。结果发现,复合钙基材料CaO-Ca₃Al₂O₆-MgO具有较好的吸附CO₂性能,提高Ca₃Al₂O₆/MgO质量比,合成材料的循环稳定性较好;降低Ca₃Al₂O₆/MgO质量比,合成材料的碳化反应速率加快,CaO转化率提高。最后,通过对不同循环次数下复合钙材料的比表面积、孔径分布、微观形貌、表面元素分布,晶相、晶粒大小进行研究分析,对合成材料的失活以及掺杂物质对烧结的抑制机理进行了讨论。     

基于钙基吸收剂循环煅烧/碳酸化反应捕集CO2的试验

利用钙基吸收剂循环煅烧/碳酸化反应(CCCR)吸收CO2是一种新型、廉价、有效的CO2捕集方法.采用热重分析仪研究了吸收剂的矿物组成、颗粒粒径、煅烧温度和碳酸化温度对CCCR快速反应阶段吸收剂循环碳酸化率(XN)的影响.结果表明:吸收剂的碳酸化反应由快速化学反应控制阶段、过渡阶段和缓慢产物层扩散控制阶段组成;白云石具有良好的抗烧结能力,白云石的XN高于石灰石;随着颗粒粒径的增大,吸收剂的XN逐渐降低;当煅烧温度超过950℃时,随着循环反应次数的增加,吸收剂的XN严重降低;吸收剂在725℃碳酸化温度时的XN最高.     

电石水解制备复合钙基吸附剂及其循环吸附CO2的特性

利用电石水解制乙炔工艺制备新型电石渣CaO/Ca12Al14O33复合钙基吸附剂,考察了Ca12Al14O33含量、碳酸化和煅烧再生温度对CaO转化率和多循环吸附CO2的影响,并与分析纯CaCO3和传统电石渣进行了比较,对其表面形貌、比表面积和孔结构进行了分析. 结果表明,新型复合钙基吸附剂在多循环煅烧/碳酸化过程中具有较好的多循环吸附CO2的性能. Ca12Al14O33有效减缓了吸附剂烧结现象. 20次循环后,自制电石渣吸附剂的CaO转化率仍保持在48%以上.     

钙基CO_2吸收剂循环活性衰减原因初探

对钙基CO2吸收剂的循环活性衰减进行了实验研究,考察了随着循环次数的增加,吸收剂的表面形态、吸收剂分子孔径及比表面积等微观结构的变化,分析了钙基CO2吸收剂循环活性衰减的原因。结果表明,随着循环次数的增加,吸收剂晶粒中的片状结构已经完全消失,取而代之的是正方体状的大晶粒,晶粒生长严重,大量空隙被封闭。而由此引起的吸收剂的比表面积的不断减小和孔容积的降低以及孔分布的改变,导致了吸收剂循环活性的衰减,吸收剂的循环转化率降低。     

钙基CO_2吸收剂改性研究进展

介绍了钙基CO2吸收剂的循环吸收特性,分析了钙基CO2吸收剂吸收能力下降的原因,并从水合作用、预热处理、掺杂添加剂及采用不同的钙前驱体等方面总结了近年来钙基CO2吸收剂改性研究现状,同时对所存在的问题及其改进方法进行了探讨。     

钙基吸收剂脱除HCl的研究进展

对钙基吸收剂脱除HCl技术的国内外研究进展进行了综述,介绍了不同类型钙基吸收剂的脱氯特性和提高钙基吸收剂脱除HCl性能的各种方法,讨论了Ca/Cl摩尔比、反应温度、粒径、反应气氛等因素对吸收剂脱氯性能的影响规律。提出重点应加强钙基吸收剂脱氯反应机理研究,解决脱氯效率较低等关键问题。并论述了生物质气化重整制氢与钙基吸收剂捕集CO2耦合技术中HCl脱除的必要性,提出HCl对钙基吸收剂循环捕集CO2性能可能存在影响。指出需研究HCl和CO2与钙基吸收剂的竞争反应规律和相互作用机理并提出协同调控方法,这对于生物质气化重整制氢技术协同捕集CO2和HCl意义重大。     

钙基CO2吸收剂的循环特性

对钙基CO₂吸收剂的循环特性进行了实验研究,考察了煅烧温度和碳酸化（吸收）温度对吸收剂最大转化率的影响,比较了常压煅烧-碳酸化（CC）过程和煅烧-水合-碳酸化（CHC）过程中吸收剂的最大吸收能力,并就添加剂对吸收剂循环性能的影响进行了实验研究.结果表明,随着循环次数的增加,吸收剂的吸收能力明显下降,未经处理的吸收剂,循环10次后,其吸收能力基本都下降到20％左右;温和的煅烧温度和较高的吸收温度下,吸收剂的最大转化率比较高;CC过程中吸收剂的最大转化率明显低于CHC过程;添加了氯化钠和碳酸钠的吸收剂的吸收能力急剧下降,但循环性能稳定;多次循环后对吸收剂进行再活化,可使其活性恢复到初始的95％.     

溶液燃烧合成法制备自活化钙铜复合CO2吸收剂的性能

首次采用溶液燃烧合成法制备了钙铜复合吸收剂用于实现低成本CO₂捕捉。在热重分析仪上研究制备参数（燃烧背景温度、煅烧时间）对吸收剂循环载氧和CO₂捕捉性能的影响,并借助SEM和氮吸附分析其微观结构。结果表明,在燃烧背景温度800℃、煅烧时间为0.5h时制得的钙铜比例为1∶1的复合CO₂吸收剂15次循环之后,钙基吸收剂转化率为51.2%,比纯的CaO提高了44.9%;采用该方法制备的吸收剂具备自活化特性,15次循环内碳酸化性能随循环次数的增加不降反升,且载氧性能非常稳定,氧化率始终高于90%。微观结构表征表明,随着循环次数的增加,复合吸收剂未发生严重烧结并且BET比表面积没有下降。实验结果为溶液燃烧合成法制备高性能钙铜复合CO₂吸收剂的进一步研究提供了基础数据。     

CaO/FA吸收剂高温吸收CO2及穿透特性

利用完全煅烧后的CaO和粉煤灰（Fly Ash）为材料制备了CaO/FA吸收剂。在350~650℃温度范围内对其碳酸化反应特性进行了研究。考察了不同质量比的CaO/FA吸收剂吸收CO2的性能。利用XRD、N2吸附等表征手段对吸收剂反应前后产物进行了表征。结果表明：通过水合反应过程,吸收剂比表面积增大,孔径在5~40nm范围内属于中孔,有利于减小CO2向颗粒内部的扩散阻力。CaO/FA吸收剂CO2吸收量随温度的升高而增加。当CaO与粉煤灰的质量比为3:1时制备的吸收剂具有最好的CO2吸收能力,在650℃时其最大CO2吸收量达到了227.13mg/g。通过多次循环试验后,吸附剂仍保持较高的CO2吸收量与稳定吸收性能。失活模型可以很好地预测CaO/FA吸收剂吸收CO2的过程,并得到了理想的吸收速率常数和失活速率常数。     

Stabilized Performance of Al‐Decorated and Al/Mg Co‐Decorated Spray‐Dried CaO‐Based CO2 Sorbents

The sharp loss‐in‐capacity in CO₂ capture as a result of sintering is a major drawback for CaO‐based sorbents used in the calcium looping process. The decoration of inert supports effectively stabilizes the cyclic CO₂ capture performance of CaO‐based sorbents via sintering mitigation. A range of Al‐decorated and Al/Mg co‐decorated CaO‐based sorbents were synthesized via an easily scaled‐up spray‐drying route. The decoration of Al‐based and Al/Mg‐based supports efficiently enhanced the cyclic CO₂ capture capability of CaO‐based sorbents under severe testing conditions. The CO₂ capture capacity losses of Al‐decorated and Al/Mg co‐decorated CaO‐based sorbents were alleviated, representing more stable CO₂ capture performance. The stabilized CO₂ capture performance is mainly attributed to the formation of Ca₁₂Al₁₄O₃₃, MgAl₂O₄, and MgO that act as the skeleton structures to mitigate the sintering of CaCO₃ during carbonation/calcination cycles.     

Effect of different organic compounds on the preparation of CaO-based CO2 sorbents derived from wet mixing combustion synthesis

CaO based sorbents have great potential for commercial use to capture CO_2 of power plants. In the demand of producing sorbents with better cyclic performance, CaO-based sorbents derived from different kinds of calcium precursors, containing calcium carbonate(CC-CaO), calcium gluconate monohydrate(CG-CaO), calcium citrate(CCi-CaO) and calcium acetate monohydrate(CA-CaO), were tested cyclically and compared using simultaneous thermal analyzer(STA). And further study was conducted on the sorbents modified with citric acid monohydrate and 50% gluconic acid solution by wet mixing combustion synthesis. The modified sorbents showed better performance and higher pore parameters as well as porous microstructure with more organic acid added. After 20 cycles of carbonation and calcination, the C2CCi8(CaO: citric acid = 2:8 by mass ratio) and C2G8(CaO: gluconic acid = 2:8 by mass ratio) sorbent possess CO_2 capture capacity of 0.45 g·g~(-1)(g CO_2 per g sorbents) and 0.52 g·g~(-1) respectively. The citric acid was more effective for modification than gluconic acid for extended 50 cycles. Furthermore, good linear relationship between CaO conversion and specific surface area as well as pore volume were determined, of which the specific surface area showed closer correlation with CaO conversion.     

高温下钙基吸附剂吸附CO2的研究

CaO基吸附剂是一种理想的CO2高温吸附剂。利用热重分析仪研究了由不同前体制备的CaO高温下对CO2的吸附性能。利用吸附仪测定了各吸附剂的比表面积等参数。实验发现CaO的最佳吸附温度范围为700—750℃;由CaC2O4.H2O制得的CaC2O4-CaO具有良好的吸附性能,在实验条件下,其吸附量为理论吸附量的89.1%;在较宽的CO2体积分数范围内,CaC2O4-CaO始终保持很高的吸附性能;吸收速率的大小受吸附剂比表面积、孔体积、孔结构等参数的共同影响。高温下,CaO基吸附剂吸附CO2的微观机理有待进一步研究。     

NO removal performance of CO in carbonation stage of calcium looping for CO2 capture

Calcium looping realizes CO2 capture via the cyclic calcination/carbonation of CaO.The combustion of fuel supplies energy for the calciner.It is unavoidable that some unburned char in the calciner flows into the carbonator,generating CO due to the hypoxic atmosphere in the carbonator.CO can reduce NO in the flue gases from coal-fired power plants.In this work,NO removal performance of CO in the carbonation stage of calcium looping for CO2 capture was investigated in a bubbling fluidized bed reactor.The effects of carbonation temperature,CO concentration,CO2 capture,type of CaO,number of CO2 capture cycles and presence of char on NO removal by CO in carbonation stage of calcium looping were discussed.CaO possesses an efficient catalytic effect on NO removal by CO.High temperature and high CO concen-tration lead to high NO removal efficiency of CO in the presence of CaO.Taking account of better NO removal and CO2 capture,the optimal carbonation temperature is 650 ℃.The carbonation of CaO reduces the catalytic activity of CaO for NO removal by CO due to the formation of CaCO3.Besides,the catalytic performance of CaO on NO removal by CO gradually decreases with the number of CO2 capture cycles.This is because the sintering of CaO leads to the fusion of CaO grains and blockage of pores in CaO,hin-dering the diffusion of NO and CO.The high CaO content and porous structure of calcium-based sorbents are beneficial for NO removal by CO.The presence of char promotes NO removal by CO in the carbonator.CO2/NO removal efficiencies can reach above 90％.The efficient simultaneous NO and CO2 removal by CO and CaO in the carbonation step of the calcium looping seems promising.     

掺杂Ce、Zr对CO2钙基吸附剂循环特性的影响

利用湿法混合-煅烧法将元素Ce、Zr掺杂到CO₂钙基吸附剂中,利用热重分析仪(TGA)研究了24种改性钙基吸附剂吸附CO₂的循环特性。研究发现:CeO₂散布在CaO晶粒之间可抑制晶粒融合,对吸附剂烧结有一定的阻碍作用;CeO₂可明显提高吸附剂在扩散控制阶段对CO₂的吸附速率,原因在于CeO₂中丰富的氧空位可促进CO₂以离子迁移的方式穿过表面产物层到达内部与CaO反应;吸附剂中CeO₂含量越高,稳定性越强;ZrO₂与CaO高温化合成具有高塔曼温度的CaZrO₃,均匀分散在CaO晶粒间,构成稳固的支撑骨架,有效抑制了吸附剂烧结。     

Modification of CaO-based sorbents prepared from calcium acetate for CO2 capture at high temperature

CaO-based sorbent is considered to be a promising candidate for capturing CO_2 at high temperature. However,the adsorption capacity of CaO decreases sharply with the increase of the carbonation/calcination cycles. In this study, CaO was derived from calcium acetate(CaAc_2), which was doped with different elements(Mg, Al,Ce, Zr and La) to improve the cyclic stability. The carbonation conversion and cyclic stability of sorbents were tested by thermogravimetric analyzer(TGA). The sorbents were characterized by N_2 isothermal adsorption measurements, scanning electron microscopy(SEM) and X-ray diffraction(XRD). The results showed that the cyclic stabilities of all modified sorbents were improved by doping elements, while the carbonation conversions of sorbents in the 1st cycle were not increased by doping different elements. After 22 cycles, the cyclic stabilities of CaO–Al, CaO–Ce and CaO–La were above 96.2%. After 110 cycles, the cyclic stability of CaO–Al was still as high as 87.1%. Furthermore, the carbonation conversion was closely related to the critical time and specific surface area.     

Efficient MgO-doped CaO sorbent pellets for high temperature CO2 capture

Novel MgO-doped CaO sorbent pellets were prepared by gel-casting and wet impregnation. The effect of Na⁺ and MgO on the structure and CO₂ adsorption performance of CaO sorbent pellets was elucidated. MgO-doped CaO sorbent pellets with the diameter range of 0.5-1.5 mm exhibited an excellent capacity for CO₂ adsorption and adsorption rate due to the homogeneous dispersion of MgO in the sorbent pellets and its effects on the physical structure of sorbents. The results show that MgO can effectively inhibit the sintering of CaO and retain the adsorption capacity of sorbents during multiple adsorption-desorption cycles. The presence of mesopores and macropores resulted in appreciable change of volume from CaO (16.7 cm³∙mol⁻¹) to CaCO₃ (36.9 cm³∙mol⁻¹) over repeated operation cycles. Ca2Mg1 sorbent pellets exhibited favorable CO₂ capture capacity (9.49 mmol∙g⁻¹), average adsorption rate (0.32 mmol∙g⁻¹∙min⁻¹) and conversion rate of CaO (74.83%) after 30 cycles.     

Acidification Optimization and Granulation of a Steel‐Slag‐Derived Sorbent for CO2 Capture

Steel slag was used as a low‐cost feedstock to prepare CaO‐based sorbents for CO₂ capture by acidification treatment, and the acidification process was optimized. Four main acidification parameters (i.e., extraction time, extraction temperature, acetic acid concentration, and solid/liquid ratio) were investigated. The solid/liquid ratio and extraction time are the most important factors that affect the CO₂ capture capacity and stability of the sorbents. The CO₂ sorption performance of optimal steel‐slag‐derived sorbent is more stable than that of naturally occurring limestone, due to the low Si/Ca ratio and the presence of MgO with high anti‐sintering ability. CaO‐based pellets with high resistance to attrition and compression were produced by extrusion of the steel‐slag‐derived sorbent powders.     

镁负载CaO基吸附剂捕集CO2性能及抗烧结机理

复合钙基吸附剂制备成本过高是限制其工业化应用的主要瓶颈问题。本文以不可溶的CaCO₃和Ca(OH)₂作为钙源,通过燃烧合成法制备钙镁复合吸附剂,在双固定床反应器上研究了其循环捕集CO₂性能。结果显示：制备得到的钙镁复合吸附剂具有更发达的孔隙结构,吸附剂表面Ca和Mg分散均匀,MgO均匀分布于CaO晶粒之间,有效提高了钙镁复合吸附剂的抗烧结特性,因此钙镁复合吸附剂循环反应过程中具有高捕集CO₂活性。以Ca(OH)₂作为钙源时,燃烧合成过程中Ca和Mg均匀同时析出,分散更加均匀,有效避免了CaCO₃作为钙源时Mg的团聚问题,因此得到的钙镁复合吸附剂循环捕集CO₂性能最优。最佳的Ca/Mg摩尔比为(8∶2)~(7.5∶2.5)。本研究以不可溶钙源制备得到高活性钙镁复合吸附剂,有效控制了吸附剂成本,具有更好的工程应用前景。