Graft copolymerization of thiophene onto polystyrene synthesized via nitroxide‐mediated polymerization and its polymer − clay nanocomposite

A new strategy for graft copolymerization of thiophene onto a polystyrene (PSt) backbone by a multi‐step process is suggested and the effects of an organoclay on the final properties of the graft copolymer sample are described. For this purpose, first poly(styrene‐co‐4‐chloromethyl styrene) [P(St‐co‐CMSt)] was synthesized via nitroxide‐mediated polymerization. Afterwards, the chlorine groups of P(St‐co‐CMSt) were converted to thiophene groups using the Kumada cross‐coupling reaction and thiophene‐functionalized PSt multicenter macromonomer (ThPStM) was synthesized. The graft copolymerization of thiophene monomers onto PSt was initiated by oxidized thiophene groups in the PSt chains after addition of ferric chloride (FeCl₃), an oxidative catalyst for polythiophene synthesis, and FeCl₃‐doped polythiophene was chemically grafted onto PSt chains via oxidation polymerization. The graft copolymer obtained was characterized by ¹H NMR and Fourier transform infrared spectroscopy, and its electroactivity behavior was verified under cyclic voltammetric conditions. Finally, PSt‐g‐PTh/montmorillonite nanocomposite was prepared by a solution intercalation method. The level of dispersion of organoclay and the microstructure of the resulting nanocomposite were probed by means of XRD and transmission electron microscopy. It was found that the addition of only a small amount of organoclay (5 wt%) was enough to improve the thermal stabilities of the nanocomposite.© 2013 Society of Chemical Industry     

Properties of n‐butyl methacrylate copolymer latex films derived from crosslinked latex particles

Films obtained from copolymer latexes of n‐butyl methacrylate (BMA) with a series of crosslinking monomers [i.e., a macromonomer crosslinker (Mac), ethylene glycol dimethacrylate (EGDMA), and aliphatic urethane acrylate] exhibited differences in their tensile properties and swelling behaviors. For P(BMA‐co‐EGDMA) copolymer, a dependence on the initiator type was obtained. It is postulated that the network microstructures for the various copolymers evolved as the result of the copolymerization reactions between the monomer pairs during the synthesis in the miniemulsion free‐radical copolymerization. These network microstructures are, therefore, hypothesized to influence the mechanical properties of the resultant films. Copolymers prepared with Mac were tough in comparison with copolymers made with EGDMA. The presence of longer linear or lightly crosslinked poly(n‐butyl methacrylate) (PBMA) chains and the looseness of the crosslinked network structures in the PBMA‐co‐Mac copolymers appear to be the factors responsible for the differences. All of the copolymer films disintegrated into swollen individual microgels when they were immersed in tetrahydrofuran. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 42–49, 2003     

Synthesis and characterization of block comb‐like copolymers P(A‐MPEO)‐block‐PSt

Amphiphilic block comb‐shaped copolymers, poly[poly(ethylene oxide) methyl ether acrylate]‐block‐polystyrene [P(A‐MPEO)‐block‐PSt] with PSt as a handle, were successfully synthesized via a macromonomer technique. The reaction of MPEO with acryloyl chloride yielded a macromonomer, A‐MPEO. The macroinitiator PSt capped with the dithiobenzoate group (PSt‐SC(S)Ph) was prepared by reversible addition–fragmentation transfer (RAFT) polymerization of styrene in the presence of benzyl dithiobenzoate, and used as macroinitiator in the controlled radical block copolymerization of A‐MPEO at room temperature under ⁶⁰Co irradiation. After the unreacted macromonomer A‐MPEO had been removed by washing with hot saturated saline water, block comb‐shaped copolymers were obtained. Their structure was characterized by ¹H NMR spectroscopy and gel permeation chromatography. The phase transition and self‐assembling behaviour were investigated by atomic force microscope and differential scanning calorimetry. Copyright © 2004 Society of Chemical Industry     

Preparation and morphology of transparent poly(methyl methacrylate)–poly(dimethylsiloxane) hybrid materials using multifunctional silicone macromonomer

In this study, transparent poly(methylmethacrylate) (PMMA)‐silicone hybrid materials, P(MMA‐co‐SigUMAx), were prepared with methylmethacrylate (MMA) and multifunctional silicone macromonomer introduced methacryl groups. The transmittance of hybrid materials improved with increase of methacryl groups of silicone macromonomer and reached around 90% T. Atomic force microscopic analysis, scanning electron microscope examinations, and copolymerization kinetics estimation by proton nuclear magnetic resonance revealed that the silicone macromonomer randomly incorporated in the copolymer with MMA by the increase of methacryl groups and suppresses the aggregation of the silicone segment. The hybrid materials introduced over 10 wt % of silicone component had water‐shedding surface and the water contact angle was elevated from 65 to 95°. Though the mechanical properties of hybrid materials were lowered by introduction of flexible silicone component, thermal property such as 5 wt % weight loss temperature were improved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Interpenetrating polymer networks based on poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) and SiO2

Copolymer such as poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) p (St‐BA‐HEMA) was prepared via free radical emulsion polymerization method. The resulting copolymer was converted to silicone secondary crosslinked interpenetrating polymer network (IPN) by condensation reaction with tetraethyl orthosilicate (TEOS). The obtained copolymers were characterized by using Fourier transform infrared spectroscopy (FTIR). Thermal properties of the copolymers were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Optical microscopy (OM) is used for studying the morphology, and then the effects of silicone concentrations, the reflux time, and composition on the phase morphology of P (St‐BA‐HEMA)‐SiO₂ IPNs were discussed. The broadening of the transition region was observed with the prolongation of the reflux time, and the tendency for aggregation of silicone on the surface was observed with Teflon as substrate plate. However, an optically transparent film was easily achieved at higher temperature due to the chemical crosslink and physical entanglement between the two phases of P (St‐BA‐HEMA)‐SiO₂. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of macromonomer from radical polymerization of styrene with a polymerizable photoiniferter

α‐(Methacrylyoxylethyloxycarbonylmethyl)‐ω‐(N,N‐diethyldithiocarbamyl)polystyrene macromonomers with different molecular weights were prepared by radical polymerization of styrene (St) using β‐methacryloxylethyl 2‐N,N‐diethyldithiocarbamylacetate (MAEDCA) as a polymerizable photoiniferter in toluene under ultraviolet light. The polymerization of St with MAEDCA carried out by a “living” process; that is, both the yield and the molecular weight of the resultant polymers increased with increasing of reaction time, and the resultant polymer was a macromonomer, for example, α‐(methacrylyoxylethyloxycarbonylmethyl)‐ω‐(N,N‐diethyldithiocarbamyl)polystyrene, designated as PSt‐macromonomer. The molecular weight of the PSt‐macromonomer depended on the concentrations of the polymerizable photoiniferter and St, as well as the conversion of St. The PSt‐macromonomer can copolymerize with MMA initiated by AIBN at 65°C to form a graft copolymer (PMMA‐graft‐PSt) with PSt branches randomly distributed along the PMMA backbone. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1350–1356, 2000     

The effects of acrylate monomers and polystyrene addition on the morphology of DOP‐plasticized styrene–acrylate polymer particles prepared by SPG emulsification and suspension polymerization

Fairly uniform copolymer particles of methyl acrylate (MA), butyl acrylate (BA), or butyl methacrylate (BMA) were synthesized via Shirasu porous glass (SPG) membrane and followed by suspension polymerization. After a single‐step SPG emulsification, the emulsion composed mainly of the monomers. Hydrophobic additives of dioctyl phthalate (DOP), polystyrene molecules, and an oil‐soluble initiator, suspended in an aqueous phase containing poly(vinyl alcohol) (PVA) stabilizer and sodium nitrite inhibitor (NaNO₂), were subsequently subjected to suspension polymerization. Two‐phase copolymers with a soft phase and a hard phase were obtained. The composite particles of poly(St‐co‐MA)/PSt were prepared by varying the St/PSt ratios or the DOP amount. The addition of PSt induced a high viscosity at the dispersion phase. The molecular weight slightly increased with increasing St/PSt concentration. The multiple‐phase separation of the St‐rich phase and PMA domains, observed by transmission electron microscopy, was caused by composition drift because the MA reactivity ratio is greater than that of St. The addition of DOP revealed the greater compatibility between the hard‐St and soft‐MA moieties than that without DOP. The phase morphologies of poly(St‐co‐MA), poly(St‐co‐BMA), and their composites with PSt were revealed under the influence of DOP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1195–1206, 2006     

Synthesis and characterization of a novel silicone containing vinylic macromonomer and its uses in the preparation of poly (silicone‐co‐styrene‐co‐butylacrylate) with montmorillonite nanocomposite emulsion

A new silicone containing macromonomer, 4‐(methacrylamido) phenoxy polymethylhydrosiloxane (4‐MPMHS) with a vinyl group, was successfully synthesized. Then poly (silicone‐co‐styrene‐co‐butylacrylate) with montmorillonite, P (Si‐co‐St‐co‐BA) with MMT nanocomposite emulsion was prepared by in situ intercalative emulsion polymerization of styrene (St), butyl acrylate (BA), and 4‐MPMHS, in the presence of organic modified montmorillonite (OMMT) with different OMMT contents (0, 0.5, 1.0, 1.5, and 2 wt %). Potassium persulphate (KPS) was used as an initiator and sodium lauryl sulfoacetate (SLSA) and nonyl phenol ethylene oxide—40 U (NP‐40) were used as anionic and nonionic emulsifiers, respectively. The resulting macromonomer was characterized by elemental analysis, Fourier transformer infrared (FT‐IR), proton (¹H NMR), and carbon (¹³C NMR) nuclear magnetic resonance spectroscopes. The OMMT was characterized by FT‐IR and X‐ray diffraction (XRD). The nanocomposite emulsions were characterized by using Fourier Transform infrared spectroscopy (FT‐IR), laser light scattering, and surface tension method. Thermal properties of the copolymers were studied using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) and then the effects of OMMT percent on the water absorption ratio and drying speed were examined. Results showed that OMMT could improve the properties of emulsion. In other words, the properties of nanocomposite emulsions were better when compared with those of the silicone‐acrylate emulsion. The property of nanocomposite emulsion containing 1 wt % OMMT was the best one, and the following advantages were obtained: smaller particle size, faster drying speed, smaller surface tension, and improved water resistance by the incorporation of OMMT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,characterization, and properties of amphiphilic block copolymer of acrylamide‐styrene by self‐emulsifying microemulsion method

The copolymerization system of acrylamide (AM) and styrene (St) was acquired by using amphiphilic block copolymer PAM‐b‐PSt with lower molecular weight as polymeric surfactant, and then the microemulsion phase diagram was drawn. The appropriate copolymerization systems were chosen in the phase diagram, and higher molecular weight amphiphilic block copolymers PAM‐b‐PSt were prepared by self‐emulsifying microemulsion method. The chemical composition and structure of the products were analyzed by FTIR, ¹H‐NMR, ¹³C‐NMR, GPC, and UV; the block structure of products was characterized by DSC, and the hydrophobic association property of the products was studied by the fluorescence probe and rotating viscosity measurement. The results showed that O/W microemulsion was also acquired by using the polymeric surfactant; 3 g polymeric surfactant was only used to disperse 0.25 g St into aqueous solution, which showed higher emulsifying efficiency. At the same time, the use of self‐emulsifying microemulsion copolymerizing system can avoid back treatment of small molecular surfactant and the purified block polymer was prepared in one step; the prepared copolymers have good hydrophobic association properties and their aqueous solution showed evident viscosity increment. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) with 2,4‐toluene diisocyanate and m‐xylene diisocyanate. I. Compatibility and impact strength of copolymers

In this study, slightly crosslinked poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) (PDMS urethane‐co‐PMMA) graft copolymers based on two diisocyanates, 2,4‐toluene diisocyanate (2,4‐TDI) and m‐xylene diisocyanate (m‐XDI), were successfully synthesized. Glass‐transition behaviors of the copolymers were investigated. Results confirm that PDMS–urethane and PMMA are miscible in the 2,4‐TDI system, but are only partially miscible in the m‐XDI system. The methylene groups adjoining the isocyanate in the m‐XDI system show increased phase‐separation behavior over the 2,4‐TDI system, in which the benzene ring adjoins the isocyanate. The functional group of PDMS–urethane improves the impact strength of the copolymers. The toughness depends on the compatibility of PDMS–urethane and PMMA segments in the copolymers. In the m‐XDI system, the impact strength of the copolymer containing 3.75 phr macromonomer achieves a maximum value (from 13.02 to 22.21 J/m). The fracture behavior and impact strength of the copolymers in the 2,4‐TDI system are similar to that of PMMA homopolymer, although they are independent of the macromonomer content in the copolymer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1875–1885, 2002     

Synthesis of α,ω‐isocyanate telechelic polymethacrylate soft segments with activated ester side functionalities and their use for polyurethane synthesis

The synthetic route for the preparation of α,ω‐isocyanate‐telechelic poly(methyl methacrylate‐co‐acryloxysuccinimide) and α,ω‐ isocyanate‐telechelic poly(methyl methacrylate‐co‐acrylamidohexanoic succinimide) soft segments is presented. The strategy includes reversible addition fragmentation chain transfer (RAFT) copolymerization and two post polymerization modification steps. The RAFT polymerizations result in copolymers with an activated ester proportion within the polymer chains of 8% N‐acryloxysuccinimide and 5% 6‐acrylamidohexanoic succinimide. The reactivity ratios of the monomer pairs were determined. In a first post polymerization reaction carboxylic acid homo telechelic polymers were prepared by reacting the ω‐dithiobenzoate end‐group with an excess of azobis(cyanovaleric acid). In a second modification step the α‐ and ω‐carboxylic acid end‐groups were reacted with hexamethylene diisocyanate and 100% isocyanate telechelic copolymers were obtained. Finally segmented polyurethanes were prepared by coupling hexamethylene diisocyanate (HDI) end capped soft segments with hard segments composed of 1,4‐butanediol and HDI. © 2013 Society of Chemical Industry     

Synthesis of poly[(decanoic acid)‐block‐styrene] diblock copolymers and their self‐assembly behavior in aqueous medium

Diblock copolymers, poly[(10‐hydroxydecanoic acid)‐block‐styrene] (PHDA‐b‐PSt), were synthesized by combining enzymatic condensation polymerization of HDA and atom transfer radical polymerization (ATRP) as of St PHDA was first obtained via enzymatic condensation polymerization catalyzed by Novozyme‐435. Subsequently, one terminus of the PHDA chains was modified by reaction with α‐bromopropionyl bromide and the other terminus was protected by chlorotrimethylsilane. The resulting monofunctional macroinitiator was used subsequently in ATRP of St using CuCl/2,2′‐bipyridine as the catalyst system to afford diblock copolymers including biodegradable PHDA blocks and well‐defined PSt blocks. Polymeric nanospheres were prepared by self‐assembly of the PHDA‐b‐PSt diblock copolymers in aqueous medium. Copyright © 2008 Society of Chemical Industry     

Polymer–metal composite particles: Metal particles on poly(St‐co‐MAA) microspheres

Poly(styrene‐co‐methacrylic acid) P(St‐co‐MAA) microspheres with a monodisperse size distribution were prepared by emulsifier‐free emulsion copolymerization of St and MAA. The effects of MAA content on the polymerization rate and the content of MAA in the copolymer were investigated by gravimetrical and IR methods, respectively. The results of XPS measurement indicated the presence of a carboxyl functional group. By chemical metal deposition, nickel or palladium particles were formed and deposited on the surface of P(St‐co‐MAA) microspheres to form P(St‐co‐MAA)Ni or P(St‐co‐MAA)Pd composite particles. XRD measurement and TEM observation confirmed that nickel and palladium metal particles in a small size (20–40 nm) were distributed on surface of the copolymer microspheres. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1693–1698, 2000     

Acrylonitrile copolymers containing guanidine oligomer: Synthesis and use for the preparation of nonleaching antimicrobial acrylic fibers

Nonleaching acrylic fibers with permanent antibacterial activity were prepared via a combination of copolymerization and a wet‐blend‐spinning method. Specifically, poly[acrylonitrile‐co‐modified poly(hexamethylene guanidine hydrochloride)] [poly(AN‐co‐M‐PHMG)] copolymers containing a covalently connected antibacterial guanidine oligomer were first synthesized via the precipitation copolymerization of acrylonitrile (AN) with a modified poly(hexamethylene guanidine hydrochloride) (M‐PHMG) macromonomer in water. Then, modified acrylic fibers were prepared from a mixture of the copolymer and commercial fiber‐grade AN terpolymer via a wet‐spinning process with dimethyl sulfoxide as the solvent. The influences of the reaction time, temperature, pH value of the medium, and amount of initiator on the copolymerization and the effect of the copolymer content on the mechanical properties and antibacterial activity of the modified acrylic fibers were investigated in detail. The results show that the M‐PHMG macromonomer exhibited a lower reactivity than AN. The poly(AN‐co‐M‐PHMG) copolymer with a PHMG content of 5.49% and an intrinsic viscosity of 11.2 dL/g could be synthesized under optimized conditions. With increasing copolymer content, the tensile strength of the modified acrylic fibers decreased slightly, and the antibacterial activity increased. The modified acrylic fibers with a copolymer content of 50% (i.e., a PHMG content of 2.75%) exhibited both good mechanical properties and excellent antibacterial activity. The additional antibacterial function would surely enlarge the applications of the fiber. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical properties of latex blends films from polystyrene particles with different sizes in a butyl acrylate‐co‐styrene copolymer matrix

Blends of polystyrene (PSt) hard particle latex with three different particle sizes (96, 72, and 61 nm) and a n‐butyl acrylate‐co‐styrene (BA‐co‐St) copolymer soft latex with a 204 nm particle size were synthesized by emulsion polymerization. Latexes were standardized at 25% solids and blended at different concentrations by wt% of PSt:BA‐co‐St for every hard particle size. Finally, films from each blend were obtained. Morphology of each film prepared was examined by transmission electron microscopy, and it was found that the hard particles are randomly distributed in the films inside the copolymer matrix. The effect on mechanical properties of different PSt concentrations and particle sizes was assessed by DMA as a function of temperature. The results indicate that rigidity of the blended latex increases as the particle size diminishes as determined by the reduction in damping in the tan δ peak. The storage modulus increases as the concentration of PSt increases in the blends and the values depend upon the size of PSt particles. Mechanical properties at tension indicate that decreasing the size of the PSt particles and increasing their concentration increase the Young's modulus and ultimate strength at tension because of an increase in the rigidity of the films. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Styrene/phosphonic acid copolymers: Synthesis and thermal,mechanical, and electrochemical characterization

In this study, a series of poly(styrene‐co‐vinyl phosphonic acid) [P(S‐co‐VPA)] copolymers were synthesized by the free‐radical copolymerization of styrene and vinyl dimethyl phosphonate followed by alkaline hydrolysis. The P(S‐co‐VPA) copolymers were characterized by size exclusion chromatography (gel permeation chromatography), Fourier transform infrared vibrational spectroscopy, proton nuclear magnetic resonance, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, and electrochemical impedance spectroscopy. Despite the difference between the copolymerization ratios of styrene and vinyl dimethyl phosphonate, the resulting copolymers presented single glass transitions at temperatures that depended on the acidic group amount. The glass transition shifted to a higher temperature and became broader as the amount of phosphonic acid increased. The storage modulus at temperatures higher than the glass transition also increased with increasing acidic groups because of intramolecular and intermolecular interactions. All of the acid copolymers were thermally stable to at least 300°C. A high oxidative stability was found for 3 : 1 P(S‐co‐VPA), which also presented conductivity values on the order of 10⁻⁶ Ω⁻¹ cm⁻¹ at room temperature. The 1 : 1 P(S‐co‐VPA) membrane presented Arrhenius‐type behavior at temperatures from 30 to 80°C and conductivity on the order of 10⁻⁵ Ω⁻¹ cm⁻¹. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Emulsion copolymerization of N-phenylmaleimide with styrene

Emulsion copolymerization of N-phenylmaleimide (PMI) with styrene (St) was conducted via semibatch and batch methods. The effect of monomer mixture composition and method of copolymerization on copolymer structure-property relationships was investigated. The semibatch copolymers have a homogeneous molecular structure, exhibiting a single T_g which increases linearly with increasing PMI content. The batch copolymers have a heterogeneous molecular structure, exhibiting two T_g's, assigned to the polystyrene (PSt) and poly(PMI-co-St) components. The composition drift in the batch-copolymerized product, at different conversion levels, was examined by DSC and FTIR techniques. In general, the inherent viscosity of the semibatch copolymers is lower than that of the corresponding batch ones. The Young's modulus increases for the semibatch copolymers, with increasing PMI content, while a clear trend for the batch copolymers is not found. The tensile strength tends to decrease for both types of copolymers when PMI content increases. The thermal stability increases with increasing PMI content in the copolymers. © 1996 John Wiley & Sons, Inc.     

Swelling behavior and diffusion studies of high‐water‐retaining acrylamide/potassium methacrylate hydrogels

Poly(acrylamide‐co‐potassium methacrylate) hydrogels were prepared by free‐radical simultaneous polymerization with aqueous solutions of acrylamide (AAm) and potassium methacrylate (KMA) with a redox initiator. The copolymerization was performed with eight different compositions of KMA at a fixed concentration of oil‐soluble crosslinkers, including 1,4‐butanediol diacrylate and ethylene glycol dimethacrylate (EGDMA). For every composition of AAm/KMA copolymer, the percentage swelling, swelling equilibrium, and diffusion characteristics were investigated. The copolymers were further studied for deswelling properties. The power law relationships of the hydrogels were evaluated for variation in terms of saline concentration. The AAm/KMA copolymers were confirmed by IR spectroscopy. Thermal studies of hydrogels were performed with differential scanning calorimetry and thermogravimetric analysis. EGDMA was found to be a better crosslinker for obtaining higher swelling and deswelling properties for the AAm/KMA hydrogels. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1153–1164, 2005     

Synthesis,characterization, and antitumor activity of poly(maleic anhydride‐co‐vinyl acetate‐co‐acrylic acid)

The ternary copolymerization of maleic anhydride (MA), vinyl acetate (VA), and acrylic acid (AA) [P(MA‐co‐VA‐co‐AA)], which is considered to be an acceptor–donor–acceptor system, was carried out in 1,4‐dioxane with benzoyl peroxide as an initiator at 70°C under a nitrogen atmosphere. Constants of complex formation for the monomer systems in the study were determined by UV–visible (hydrogen‐bonding complex) and ¹H‐NMR (charge transfer complex) methods, respectively. The results show that polymerization of the P(MA‐co‐VA‐co‐AA) system proceeds by an alternating terpolymerization mechanism. It is shown that the synthesized copolymers have typical polyelectrolyte behavior, ability for reversible hydrolysis–anhydrization reactions, and semicrystalline structures. In these cases, including radical polymerization, and formation of semicrystalline structures, the hydrogen‐bonding effect plays a significant role. The in vitro cytotoxicities of the synthesized terpolymer and alternating copolymer were evaluated using Raji cells (human Burkitt lymphoma cell line). The antitumor activities of prepared anion‐active copolymers were studied using methyl–thiazol–tetrazolium colorimetric assay and 50% of the cytotoxic dose of each copolymer and terpolymer were calculated. Hydrolyzed P(MA‐co‐VA‐co‐AA) and P(MA‐alt‐AA) copolymers have sufficiently high antitumor activity, which depends on the amount of hydrogen‐bonding carboxylic groups and their regular distribution in the side chain of functional macromolecules. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3425–3432, 2006     

Effect of methyl methacrylate on the properties of transparent flame retardant unsaturated phosphate ester copolymer

The effect of methyl methacrylate (MMA) on the properties of transparent flame retardant unsaturated phosphate ester copolymer (poly[UPE‐co‐MMA]) prepared by bulk polymerization technique was investigated. Fourier transform infrared spectra, gel fraction (G) test, and dynamic mechanical analysis revealed the structure and crosslinking density of poly(UPE‐co‐MMA) copolymers. The thermal degradation and flame retardancy of copolymers were indicated by thermogravimetric analysis, limiting oxygen index (LOI), and microscale combustion calorimeter (MCC) test. Besides, the mechanical properties and transparency were tested with testing machines and solid ultraviolet absorption spectra. As the MMA content increased to 50%, the copolymer contained 50 wt% MMA showed the maximal G (88.93%) and transmittance was up to 91.72%. From the poly(UPE‐co‐MMA) copolymers, the tensile strength increased from 14.62 to 26.95 MPa, assigned to the increase of crosslinking density of copolymers. The char yield of poly(UPE‐co‐MMA) was up to 21.18 wt%, which was a result of decomposition of phosphate groups, producing a phosphorus‐rich layer that increased the thermal stability of the residues. LOI and MCC results confirm that the introduction of MMA can retain the flame retardancy of copolymer remarkably. POLYM. ENG. SCI., 59:2103–2109, 2019. © 2019 Society of Plastics Engineers