Application of raman spectroscopy to monitor and quantify ethyl esters in soybean oil transesterification

Biodiesel (FA esters) has become very attractive as an alternative diesel fuel owing to its environmental benefits. Transesterification is the most usual and important method to make biodiesel from vegetable oils. This article investigates the potential for using Raman spectroscopy to monitor and quantify the transesterification of soybean oil to yield ethyl esters. The differences observed in the Raman spectra of soybean oil after transesterification were a peak at 2932 cm⁻¹ ( ), the displacement of the v _C=O band from 1748 to 1739 cm⁻¹, and the bands at 861 (v _R-C=O and v _C-C) and 372 cm⁻¹ (δ _CO-O-C). Uni- and multivariate analysis methods were used to build several analytical curves and then applied in known samples, treated as unknowns, to test their ability to predict concentrations. The best results were achieved by Raman/PLS calibration models (where PLS=partial least squares regression) using an internal normalization standard (v _=C-H band). The correlation coefficient (R ²) values so obtained were 0.9985 for calibration and 0.9977 for validation. Univariate regression analysis between biodiesel concentration and the increasing intensity of band or v _C=O displacement showed R ² values of 0.9983 and 0.9742, respectively. Although spectroscopic methods are less sensitive than chromatographic ones, the data obtained by spectroscopy can be correlated with other techniques, allowing biodiesel yield and quality to be quickly assessed.     

Electrochemical properties of cathode materials LiNi1−y Co y O2 synthesized using various starting materials

LiNi_1−y Co _y O₂ samples were synthesized at 800 °C and 850 °C, by the solid-state reaction method, using the starting materials LiOH·H₂O, Li₂CO₃, NiO, NiCO₃, Co₃O₄ and CoCO₃. The LiNi_1−y Co _y O₂ synthesized using Li₂CO₃, NiO and Co₃O₄ exhibited the α-NaFeO₂ structure of the rhombohedral system (space group ). As the Co content increased, the lattice parameters a and c decreased. The reason is that the radius of the Co ion is smaller than that of the Ni ion. The increase in c/a shows that a two-dimensional structure develops better as the Co content increases. The LiNi_0.7Co_0.3O₂ synthesized at 800 °C using LiOH · H₂O, NiO and Co₃O₄ exhibited a larger first discharge capacity of 162 mAh g⁻¹ than the other samples. The cycling performances of the samples with the first discharge capacity larger than 150 mAh g⁻¹ were investigated. LiNi_0.9Co_0.1O₂ synthesized at 850 °C using Li₂CO₃, NiO and Co₃O₄ showed excellent cycling performance. Samples with larger first discharge capacity will have a greater tendency for lattice destruction due to expansion and contraction during intercalation and deintercalation, than samples with smaller first discharge capacity. As the first discharge capacity increases, the capacity fading rate thus increases.     

Effects of rice cultivars on methane fluxes in a paddy soil

CH₄ emission and its relevant processes involved (i.e. CH₄ production, rhizospheric CH₄ oxidation and plant-mediated CH₄ transport) were studied simultaneously to comprehensively understand how rice cultivars (Yanxuan, 72031, and 9516) at growth stages (early and late tillering, panicle initiation, ripening, and harvest stage) affect CH₄ emission in a paddy soil. Over the entire rice-growing season, Yanxuan had the highest CH₄ emission flux with 5.98 g CH₄ m^–2 h^–1 followed by 72031 (4.48 g CH₄ m^–2 h^–1) and 9516 (3.41 g CH₄ m^–2 h^–1). The highest CH₄ production rate of paddy soils planted to Yanxuan was observed with 18.0 g CH₄ kg_{{ (d.w.soil)}} h^–1 followed by the soil planted to 9516 (17.5 g CH₄ kg_{{ (d.w.soil)}} h^–1). For each cultivar, both rhizospheric CH₄ oxidation ability and plant-mediated CH₄ transport efficiency varied widely with a range of 9.81–76.8% and 15.5–80.5% over the duration of crop growth, respectively. Multiple regression analyses showed that CH₄ emission flux was positively related with CH₄ production rate and rice plant-mediated CH₄ transport efficiency, but negatively with rhizospheric CH₄ oxidation (R ²=0.425 for Yanxuan, P<0.01; R ²=0.426 for 72031, P<0.01; R ²=0.564 for 9516, P<0.01). The contribution of rice plants to CH₄ production seems to be more important than to rhizospheric CH₄ oxidation and plant-mediated transport in impact of rice plants on CH₄ emission.     

Bleaching kinetics of sunflowerseed oil

The bleaching process for sunflowerseed oil follows a rate formula, log (A/A ₀)=−κ , according to absorbance measurements. The dark color of crude oil converts to a light color as the absorbance value decreases. The activation energy E _a was calculated from the Arrhenius equation as 3 kJ, and other activation thermodynamic parameters were determined as ΔS ^⊄=−4.4 J K⁻¹, ΔH ^⊄=−31.2 J mol⁻¹, and ΔG ^⊄=1.6 kJ mol⁻¹. The study showed that the bleaching process was exothermic, presented a decrease of entropy, and was a nonspontaneous process during activation.     

Variation of LiNiO<Subscript>2</Subscript> cathode properties with substitution of Ga,In and Tl by the combustion method

LiNi_1-y M_yO₂ (M = Ga, In and Tl, y = 0.010, 0.025 and 0.050) with small y were synthesized by the combustion method by calcining in an O₂ stream at 750 °C for 36 h. XRD analyses, SEM observation and measurement of the variation of discharge capacity with the number of cycles were carried out. All the samples had the Rm structure and LiNi_1-y In _y O₂ contained LiInO₂ phase as an impurity. Among LiNi_1-y Ga _y O₂ the sample with y = 0.025 had a relatively large first discharge capacity (172.2 mAh g⁻¹) and relatively good cycling performance (discharge capacity 140.3 mAh g⁻¹ at n = 20). For LiNi_0.975M_0.025O₂ (M = Ga, In and Tl), the first discharge capacity decreased in the order of the substituted element Ga, In and Tl. The variations of cation mixing and hexagonal ordering with the substituted element (decrease in I₀₀₃/I₁₀₄ and increase in R-factor from M = Ga through M = Tl) are considered to lead to the behavior of the first discharge capacity with the substituted element. LiNi_0.975Tl_0.025O₂ had the smallest degradation rate of the discharge capacity.     

Synthesis and characterization of LiNi1/3Mn1/3Co1/3O2 by wet-chemical method

A series of LiNi_1/3Mn_1/3Co_1/3O₂ samples with α-NaFeO₂ structure belonging to the D_3d⁵ space group were synthesized using tartaric acid as a chelating agent by wet-chemical method. Different acid to metal-ion ratios R have been used to investigate the effect of this parameter on the physical and electrochemical properties. We have characterized the reaction mechanism, the structure, and morphology of the powders by TGA, XRD, SEM and TEM imaging, completed by magnetic measurements, Raman scattering spectroscopy, and complex impedance experiments. We find that the LiNi_1/3Mn_1/3Co_1/3O₂ sintered at 900 °C for 15 h with an acid to metal-ion ratio R = 2 was the optimum condition for this synthesis. For this optimized sample, only 1.3% of nickel-ions occupied the 3b Wyckoff site of the lithium-ions sublattice. The electrochemical performance has been investigated using a coin-type cell containing Li metal as the anode. The electronic performance is correlated to the concentration of the Ni(3b) defects that increase the charge transfer resistance and reduce the lithium diffusion coefficient. The optimized cell delivered an initial discharge capacity of 172 mAh g⁻¹ in the cut-off voltage of 2.8-4.4 V, with a coulombic efficiency of 93.4%.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Factors influencing the structure of electrochemically prepared α-MnO2 and γ-MnO2 phases

The α- and γ-phases of MnO₂ prepared by electrolysis of MnSO₄ and M_xSO₄ (where M = Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺ or Mg²⁺) in aqueous solutions at various pH and voltage E_v values under ambient conditions have been systematically studied. The structures of powdery MnO₂ produced are found to depend on the radius of the M^z+ counter cation in addition to the pH and E_v conditions. In order to achieve the α-phase for MnO₂ formation under neutral pH condition, the radius of counter cation must be equal to or greater than 1.41 Å, the size of the K⁺ cation. The relative concentration ratio of [MnO₄⁻]_transient/[Mn²⁺], which is related to the pH-E_v conditions, also affects the structure of MnO₂ produced with counter ions smaller than K⁺. For samples prepared in acidified solution with the counter ions of Li⁺, Na⁺ or Mg²⁺ at 2.2 V, the electrolysis products display the γ-MnO₂ phase while those prepared at 2.8 V electrolysis produce a mixture of γ-MnO₂ and α-MnO₂ phases. Single phase of α-MnO₂ is identified in the 5 V electrolysis products. Furthermore, the valence state of manganese was found to decrease as the applied voltage was reduced from 5.0 to 2.2 V. This implies that the lower [MnO₄⁻]_transient/[Mn²⁺] ratio or the less oxidative condition is responsible for the non-stoichiometric MnO₂ structure with oxygen deficiency.     

Oxygen isotope equilibration and exchange as probes for differing dioxygen interactions with pure and rhodia-promoted CeO2 and Al2O3

Comparisons are made between the catalytic activities of CeO₂, Al₂O₃ and Rh₂O₃ when pure, or in the case of CeO₂ and Al₂O₃ when promoted by rhodia dispersed thereon, in respect of: (a) activity at 290 K for homomolecular oxygen isotope equilibration of an equimolar (¹⁸O₂ + ¹⁶O₂) probe gas, the so-called R₀ process, (b) activity under T-ramp for heterophase oxygen isotope exchange between surface lattice and O₂ highly enriched in ¹⁸O, which is shown to occur predominantly by single-stay exchange of both oxygen atoms of dioxygen (the so-called R₂ process). This revised version was published online in June 2006 with corrections to the Cover Date.     

Effect of pulse reversal on the properties of pulse plated CdSe x Te1−x thin films

CdSe _x Te_1–x thin films with 0 < x < 1 were deposited on titanium and conducting glass substrates by pulse electrodeposition using microprocessor control. Formation of the solid solution takes place for values of x(0 < x < 1). The films were characterized by X-ray diffraction. While the as-deposited films are cubic in nature, those annealed at 475 °C in air indicate hexagonal structure and the lattice parameters increase with increasing value of x. From the optical absorption measurements the band gap of the material was calculated. The value of the band gap varies from 1.42 to 1.70 eV as x varies from 0 to 1. The photoelectrochemical (PEC) characteristics were obtained for all compositions of CdSe _x Te_1–x (x = 0–1). The output parameters for CdSe_0.66Te_0.34 with 9% duty cycle at an intensity of 80 mW cm^–2 using 1 M polysulphide as the redox electrolyte, are V _OC of 398 mV, J _SC of 5.59 mA cm^–2, ff of 0.45, of 4.73%, R _s of 13 , R _sh of 1.50 k. The output parameters were found to increase with 60 ms pulse reversal. After photoetching for 40 s, a V _OC of 481 mV, J _SC of 16.00 mA cm^–2, ff of 0.57, of 5.46%, R _s of 6 , R _sh of 2.16 k were obtained.     

Li-ion diffusion kinetics in LiMn2O4 thin films prepared by pulsed laser deposition

LiMn₂O₄ thin films were deposited on Au substrates by pulsed laser deposition (PLD). The Li-ion chemical diffusion coefficients of the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), potentiostatic intermittent titration technique (PITT), and electrochemical impedance spectroscopy (EIS). It was found that the values by CV and PITT were in the order of 10⁻¹³ cm² s⁻¹, and those by EIS and GITT were in the range of 10⁻¹³ to 10⁻¹¹ and 10⁻¹⁴ to 10⁻¹¹ cm² s⁻¹, respectively. These data were compared with the previously reported values.     

Selective transfer of cations between two electrolytes using the intercalation properties of Chevrel phases

A device based on an electrochemical transfer junction (constituted by M_xMo₆S₈ or M_xMo₆Se₈) placed between two tanks allows the transfer of cations by application of current density controlled between electrodes placed in tanks. The transfer protocol was tested on different mixed electrolytes containing cations directly engaged in the batteries industry (M²⁺ = Co²⁺, Ni²⁺, Cd²⁺, Zn²⁺, Mn²⁺, Cu²⁺). Good performances of the process are provided until 1.6 mA cm⁻². The electrolysis through an electrochemical transfer junction made of Chevrel phases represents a suitable method for the selective extraction of cations with appreciable selectivity rates with an appropriate choice of the host lattice (sulfide or selenide). Remarkable separations between Co/Ni, Zn/Mn with Mo₆S₈ and Cd/Zn, Cd/Ni, Cd/Co and Zn/Ni, with Mo₆Se₈ were observed.     

Particle size effect of Li[Ni0.5Mn0.5]O2 prepared by co-precipitation

Spherical (Ni_0.5Mn_0.5)(OH)₂ with different secondary particle size (3 μm, 10 μm in diameter) was synthesized by co-precipitation method. Mixture of the prepared hydroxide and lithium hydroxide was calcined at 950 °C for 20 h in air. X-ray diffraction patterns revealed that the prepared material had a typical layered structure with space group. Spherical morphologies with mono-dispersed powders were observed by scanning electron microscopy. It was found that the layered Li[Ni_0.5Mn_0.5]O₂ delivered an initial discharge capacity of 148 mAh g⁻¹ (3.0-4.3 V) though the particle sizes were different. Li[Ni_0.5Mn_0.5]O₂ having smaller particle size (3 μm) showed improved area specific impedance due to the reduced Li⁺ diffusion path, compared with that of Li[Ni_0.5Mn_0.5]O₂ possessing larger particle size (10 μm). Although the Li[Ni_0.5Mn_0.5]O₂ (3 μm) was electrochemically delithiated to Li_0.39[Ni_0.5Mn_0.5]O₂, the resulting exothermic onset temperature was around 295 °C, of which the value is significantly higher than that of highly delithiated Li_1−δCoO₂ (∼180 °C).     

Molecular weight averages as criteria for quality assessment of heated oils and fats

A simple method for quality assessment of heated oils and fats is described. The proposed method involves precise determination of molecular weight averages (MWA)viz., the weight average molecular weight ( ), the number average molecular weight ( ) and the Z-average molecular weight ( ) by high performance size exclusion chromatography (HPSEC) and their quantitative correlation to percent polar material obtained by column chromatography (CC). Change in MWA on heat treatment of fourteen different edible oils and fats at 180° ± 2°C for eight 8-hr days is studied. Relative standard deviations and regression coefficients of correlation between MWA and their ratios ( , { }, { }, { }, { } and { )vs percent polar material have been reported. Probable discard time was predicted for all the oils based on the above-mentioned correlations and also from the percent of high molecular weight (H. Mwt) species formed. It was observed that the oils which are generally recommended for coronary patients deteriorated faster. A possibility of extending this methodology to the frying oils is suggested. Part of the work was presented at “40th Pittsburgh Conference on Analytical Chemistry and Applied Spectroscopy” at Georgia World Congress Centre, USA, 1989. IICT Communication No. 2630.     

Study of the Supported K2MoO4 Catalyst for Methanethiol Synthesis by One Step from High H2S-Containing Syngas

ESR and XPS are used to study the Mo-based catalysts MoO₃/K₂CO₃/SiO₂ and K₂MoO₄/SiO₂ prepared with two kinds of precursors, (NH₄)₆Mo₇O₂₄4H₂O and K₂MoO₄. The catalytic properties of the catalysts for methanethiol synthesis from high H₂S-containing syngas are explored. The activity assay shows that the two catalysts have much the same activity for the reaction. By the ESR characterization of both functioning catalysts, the resonant signals of oxo-Mo(V) (g=1.93), thio-Mo(V) (g=1.98) and S (g=2.01 or 2.04) can be detected. In the catalyst MoO₃/SiO₂ modified with K₂CO₃, as increasing amounts of K₂CO₃ are added, the content of oxo-Mo(V) increases, but thio-Mo(V) decreases. The XPS characterization indicates that Mo has mixed valence states of Mo⁴⁺, Mo⁵⁺ and Mo⁶⁺, and that S includes three kinds of species: S^2– (161.5 eV), [S–S]^2– (162.5 eV) and S⁶⁺ (168.5 eV). Adding K₂CO₃ promoter to the catalysts, the Mo species of high valence state is easily sulphided and reduced to Mo₂S and oxo-M(V), and the derivation of [S–S]^2– and S^2– species from S is promoted simultaneously. The methanethiol synthesis is favored if the mole ratio of (Mo⁶⁺ + Mo⁵⁺)/Mo⁴⁺ 0.8 and S^2–/[S–S]^2– is kept at a value of about 1.     

Evaluation of electrical energy per order (EEO) with kinetic modeling on the removal of Malachite Green by US/UV/H2O2 process

The kinetics of decolorization of Malachite Green (MG) as a model cationic dye from textile industry, by US/UV/H₂O₂ process, was investigated with nonlinear regression analysis. The experimental results indicated that the decolorization kinetics of MG in this process fit well by pseudo-first order kinetics. With nonlinear regression analysis a model was developed for pseudo-first order constant (k_ap) as a function of operational parameters such as initial concentrations of H₂O₂ (25-600 mg l^− 1) and MG (1.82-9.87 mg l^− 1), temperature (294-307 K) and power density (0.049-0.16 W ml^− 1) as following:

     

Reduction of NO by CO on PdO-MoO3/γ-Al2O3 of low molybdena loading

The catalytic activity for the reduction of NO by CO of five PdO-MoO₃/-Al₂O₃ catalysts is compared in the presence of varying amounts of oxygen at reaction temperatures from 25 to 550 °C. The samples were prepared by different methods and contain about 2% of Mo and 2% Pd. Results are compared with the activities and selectivities of PdO/ -A1₂O₃ and PdO-MoO₃/-Al₂O₃ containing 2% Pd and 2% Pd + 20% Mo, respectively. All catalysts showed appreciable activity at temperatures between 300 and 550 °C and at stoichiometric ratios,R, of the oxidizing to reducing gases of 0.1 <R < 1.1. The activity of three PdO-MoO₃/ -A1₂O₃ catalysts with low concentrations of Mo and Pd was found to be significantly higher than the activity of PdO/-Al₂O₃ at 1.1 <R < 1.3 and at temperatures between 300 and 500 °C. The improved activity is ascribed to the interaction of the active metals.     

Graft Copolymerization onto Starch–I. Synthesis and Optimization of Starch Grafted with N-tert-Butylacrylamide Copolymer and its Hydrogels

Grafting of N-tert-butylacrylamide (BAM) onto starch in aqueous medium initiated by ceric ammonium nitrate ion has been studied under N₂ atmosphere. The optimum conditions with respect to monomer concentration, initiator concentration, polymerization temperature, polymerization time and material to liquor ratio were studied in terms of percent of grafting efficiency (%GE) and percent of grafting yield (%GY). The optimum conditions obtained for the grafting of BAM on 1.0 g starch were: [BAM]=0.020 mol/L, [CAN]=0.91×10^–3 mol/L, Temperature=30C, and Time=240 min. Starch-g-BAM copolymer was characterized by FTIR, TGA for thermal stability, X-ray diffraction (XRD) for the crystallinity and scanning electron microscope (SEM) for surface morphology of the copolymer. Acid hydrolysis and viscosity average molecular weight (M _v) of copolymer were evaluated for the copolymer. Hydrogels prepared by grafting of BAM onto gelatinized starch showed maximum water uptake and moisture retain of 162% and 63% respectively.