Functionalized three-dimensional graphene networks for high performance supercapacitors

Three-dimensional (3D) thermal reduced graphene network (TRGN) deposition on Ni foam without any conductive agents and polymer binders was successfully synthesized by dipping Ni foam into graphene oxide (GO) suspension and subsequent thermal reduction process. The direct and close contact between thermal reduced graphene and Ni foam is beneficial to the enhanced conductivity of the electrode, as well as the improvement of ion diffusion/transport into the electrode. Additionally, low-temperature reduction of GO possesses a large amount of stable oxygen-containing groups that can provide high pseudocapacitance. As a result, the TRGN electrode delivers a high specific capacitance of 442.8 F g⁻¹ at 2 mV s⁻¹ in 6 mol L⁻¹ KOH. Moreover, symmetric supercapacitor based on TRGN exhibits a maximum energy density of 30.4 Wh kg⁻¹ based on the total mass of the two electrodes in 1 mol L⁻¹ Na₂SO₄ electrolyte, as well as excellent cycling stability with 118% of its initial capacitance after 5000 cycles.     

A novel method for direct growth of a few-layer graphene on Al2O3 film

Direct growth of graphene on Al₂O₃ film is successfully achieved assisted with NiAl₂O₄ film on a SiO₂ substrate by chemical vapor deposition at 800 °C. The Ni particles are first uniformly separated out on the substrate, and play an important role in capturing carbon atoms and accelerating the nucleation to grow high quality graphene rooting on insulating Al₂O₃ film. The thickness of graphene films can be tuned from two layers to few layers (<10) by changing growth time. The continuous graphene films exhibit extremely excellent electrical transport properties with a sheet resistance of down to 18.5 Ω sq⁻¹. The graphene/Ni/Al₂O₃/SiO₂ is used as the counter electrode of dye sensitized solar cell which achieves a photovoltaic efficiency of 7.62%.     

Densification of SiO2–cBN composites by using Ni nanoparticle and SiO2 nanolayer coated cBN powder

Cubic boron nitride (cBN) powder was coated with Ni nanoparticle and SiO₂ nanolayer (abbreviated as cBN/Ni and cBN/SiO₂, respectively) by rotary chemical vapor deposition (RCVD), and compacted with SiO₂ powder by spark plasma sintering at 1473–1973 K for 0.6 ks. The effects of Ni and SiO₂ coatings on the densification, phase transformation of cBN and hardness of SiO₂–cBN composites were compared. The phase transformation of cBN to hBN was identified at 1973 K in SiO₂–cBN/SiO₂ composites, 300 K higher than that in SiO₂–cBN/Ni composites, indicating that SiO₂ retarded the transformation of cBN. The relative density of SiO₂–cBN/SiO₂ with 50 vol% cBN sintered at 1873 K was 99% with a hardness of 14.5 GPa.     

Electrochemically synthesized graphene/polypyrrole composites and their use in supercapacitor

Composite films consisting of polypyrrole (PPy) and graphene oxide (GO) were electrochemically synthesized by electrooxidation of 0.1 M pyrrole in aqueous solution containing appropriate amounts of GO. Simultaneous chronoamperometric growth profiles and frequency changes on a quartz crystal microbalance showed that the anionic GO was incorporated in the growing GO/PPy composite to maintain its electrical neutrality. Subsequently, the GO was reduced electrochemically to form a reduced GO/PPy (RGO/PPy) composite by cyclic voltammetry. Specific capacitances estimated from galvanostatic discharge curves in 1 M H₂SO₄ at a current density of 1 A g^?1 indicated that values for the RGO/PPy composite were larger than those of a pristine PPy film and the GO/PPy composite. In the case of 6 mg mL^?1 GO for the preparation of GO/PPy, a high specific capacitance of 424 F g^?1 obtained at the electrochemically prepared RGO/PPy composite indicated its potential for use as an electrode material for supercapacitors.     

The size and dispersion effect of modified graphene oxide sheets on the photocatalytic H2 generation activity of TiO2 nanorods

Nano graphene oxide (NGO) was produced by further refluxing graphene oxide (GO) sheets in HNO₃, and carboxylic acid functionalized graphene oxide (GO–COOH) was obtained by a simple etherification reaction between GO and chloroacetic acid. The GO, GO–COOH and NGO sheets are combined with TiO₂ nanorods by a two-phase assembling method, and confirmed by transmission electronic microscopy. The GO–TiO₂, GO–COOH–TiO₂ and NGO–TiO₂ composites are used in a comparative study of photocatalytic H₂ generation activity under UV light irradiation. The H₂ generation rate of TiO₂ nanorods was slightly increased from 15 to 30 mL h⁻¹ g⁻¹ by replacing oleic acid ligands with hydrophilic dopamine, and significantly increased to 105 mL h⁻¹ g⁻¹ after combining with GO sheets. The further comparative study shows that GO–COOH–TiO₂ composite has higher H₂ generation rate of 180 mL h⁻¹ g⁻¹ than that of GO–TiO₂ and NGO–TiO₂ composites.     

Tubular graphene nanoribbons with attached manganese oxide nanoparticles for use as electrodes in high-performance supercapacitors

Graphene nanoribbons (GNRs) with tubular shaped thin graphene layers were prepared by partially longitudinal unzipping of vapor-grown carbon nanofibers (VGCFs) using a simple solution-based oxidative process. The GNR sample has a similar layered structure to graphene oxide (GO), which could be readily dispersed in isopropyl alcohol to facilitate electrophoretic deposition (EPD). GO could be converted to graphene after heat treatment at 300 °C. The multilayer GNR electrode pillared with open-ended graphene tubes showed a higher capacitance than graphene flake and pristine VGCF electrodes, primarily due to the significantly increased surface area accessible to electrolyte ions. A GNR electrode with attached MnO₂ nanoparticles was prepared by EPD method in the presence of hydrated manganese nitrate. The specific capacitance of GNR electrode with attached MnO₂ could reach 266 F g⁻¹, much higher than that of GNR electrode (88 F g⁻¹) at a discharge current of 1 A g⁻¹. The hydrophilic MnO₂ nanoparticles attached to GNRs could act as a redox center and nanospacer to allow the storage of extra capacitance.     

Rapid and non-destructive identification of graphene oxide thickness using white light contrast spectroscopy

By white light contrast spectroscopy, we have successfully identified number of graphene oxide (GO) layers (⩽10 layers) and obtained a new refractive index of GO sheets (⩽10 layers) of n_GO = 1.2–0.24i. For few layers (⩽10 layers) GO sheets, both the contrast at ∼580 nm wavelength and the Raman intensity of G band linearly increase with the increase of the layer numbers. However, due to the laser induced heating effects and the requirement of a reference Raman spectrum in Raman spectroscopy measurements, contrast spectroscopy is non-destructive and more efficient. Simulations based on the Fresnel’s equations agree well with evolution of the contrast and G band intensity as a function of number of layers. The precise refractive index of GO obtained in this work can be widely used in further study of GO. Therefore, our experimental contrast values can be directly used as a standard to identify the thickness of GO on Si substrate with 300 nm SiO₂ capping layer, which paves a novelty way towards future fundamental research and applications of graphene-based materials.     

Simultaneous reduction,exfoliation, and nitrogen doping of graphene oxide via a hydrothermal reaction for energy storage electrode materials

Nitrogen (N)-doped graphene (NG) sheets were prepared using (NH₄)₂CO₃ and an aqueous dispersion of graphene oxide (GO) by an eco-friendly hydrothermal reaction. The in situ produced ammonia played an important role in the simultaneous nitrogen doping, the reduction and exfoliation of GO. The (NH₄)₂CO₃/GO mass ratio and reaction temperature were varied to investigate the effects on the N doping level. The elemental analysis determined from the X-ray photoelectron spectroscopy showed that the nitrogen content of the NG was about 10.1 at.% and the oxygen content decreased significantly due to the hydrothermal reduction of GO. The electrochemical performances of the NG sheets increased with increasing doped N content. The highest specific capacitance of 295 F g⁻¹ at a current density of 5 A g⁻¹ and the highest specific surface area of 412 m² g⁻¹ were observed with the sample processed at 130 °C. The retention of the specific capacitance was maintained at ∼89.8% after 5000 charge–discharge cycles. These results imply that NG sheets obtained by this simple eco-friendly approach are suitable for use in high performance energy storage electrode materials.     

Low-cost preparation of a conductive and catalytic graphene film from chemical reduction with AlI3

AlI₃ synthesized by I₂ and Al in ethanol was used as reductive agent to directly obtain flexible reductive graphene oxide (RGO) films with high conductivity of 5320 S/m from graphene oxide (GO) films at a low temperature of 80 °C. This reductive method has provided a low-cost and effective route for large-scale production of graphene with high catalytic activity. Structural evolution during the reduction of GO was studied by Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy. The RGO films served as counter electrode exhibited high electrochemical activity.     

Preparation and ferroelectric properties of (Na0.5Bi0.5)0.94Ba0.06TiO3 thin films deposited on Pt electrodes using LaNiO3 as buffer layer

(Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ thin films were deposited on Pt/Ti/SiO₂/Si (1 1 1) and LaNiO₃/Pt/Ti/SiO₂/Si (1 1 1) substrates by a sol–gel process. The phase structure and ferroelectric properties were investigated. The X-ray diffraction pattern indicated that the (Na_0.5Bi_0.5)_0.94Ba_0.06TiO₃ thin film deposited on Pt/Ti/SiO₂/Si (1 1 1) substrates is polycrystalline structure without any preferred orientation. But the thin film deposited on LaNiO₃/Pt/Ti/SiO₂/Si substrates shows highly (1 0 0) orientation (f ≥ 81%). The leakage current density for the two thin films is about 6 × 10^?3 A/cm² at 250 kV/cm, and thin film deposited on LaNiO₃/Pt/Ti/SiO₂/Si substrates possessed a much lower leakage current under high electric field. The hysteresis loops at an applied electric field of 300 kV/cm and 10 kHz were acquired for the thin films. The thin films deposited on LaNiO₃/Pt/Ti/SiO₂/Si substrates showed improved ferroelectricity.     

Effect of UV irradiation on magnetic behavior of reduced graphene oxide decorated with nickel nanostructure

Reduced graphene oxide (RGO) decorated with nickel has been synthesized via an in-situ reduction of graphene oxide (GO) and nickel nitrate using NaOH and hydrazine. The starting materials Ni (NO₃)₂ and GO were taken in two different ratios and the products formed were designated as RGNi₂ and RGNi₁. The formation of the composite was confirmed by the appearance of X-ray diffraction peaks at 44.5°, 51.9°, 76.5° corresponding to Ni and at 24.8°and 43.2° for RGO. The RGNi₂ was irradiated with UV light (λ=254 nm) for different durations (2, 6, 12, 24 and 48 h). Intensity ratio of d and g-bands (I_d/I_g) of Raman spectra increases from 1.18 to 1.47 over the duration of irradiation period (2–48 h). The magnetization measurements using the vibrating sample magnetometer (VSM) of these samples reveal their ferromagnetic behavior. The calculated saturation magnetization (M_S) value of Ni, RGNi₁and RGNi₂ is 47.86, 30.56 and 8.25 emu/g respectively and the corresponding coercivity (H_C) value is found to be 181, 227 and 296 Oe. The M_S of RGNi₂ is found to increase to 10.65 emu/g after 48 h of irradiation. This enhancement in the M_S(~23%) with irradiation may be due to defect formation by the UV light.     

Hollow graphene spheres self-assembled from graphene oxide sheets by a one-step hydrothermal process

We developed a one-step hydrothermal method to assemble graphene oxide (GO) sheets into hollow graphene spheres (HGSs), using only a GO/H₂SO₄ aqueous suspension as the starting material. Scanning electron microscope, focused ion beam scanning electron microscope and transmission electron microscope images show that the as-prepared HGSs vary from 1 to 3 μm in diameter and have a hollow interior structure. The as-prepared HGSs show a high capacitance of 207 F g⁻¹, as well as good rate capability and cycling stability when used as electrode materials for supercapacitors.     

An efficient method of producing stable graphene suspensions with less toxicity using dimethyl ketoxime

A highly stable graphene suspension has been prepared using dimethyl ketoxime (DMKO) as reductant. Nitrogen was doped into the graphene plane at the same time as the graphene oxide (GO) sheets were reduced. X-ray photoelectron spectroscopy indicated that the C/O ratio of graphene was significantly increased after GO was treated with DMKO and the quantity of nitrogen incorporated into the graphene lattice was 3.67 at.%. The electrical conductivity of the graphene paper was found to be ～10² S m^?1, which was 5 orders of magnitude better than that of GO, and this demonstrated the effective chemical reduction of GO. The mechanism of the chemical reaction of GO with DMKO was also discussed. The as-produced graphene material showed good capacitive behavior and long cycle life with a specific capacitance of ～140 F g^?1.     

Catalytic gasification of lignin with Ni/Al2O3–SiO2 in sub/supercritical water

Lignin has been gasified with a Ni/Al₂O₃–SiO₂ catalyst in sub/supercritical water (SCW) to produce gaseous fuels. XRD pattern at 6θ angle shows characteristic peaks of crystalline NiO, NiSi, and AlNi₃, suggesting that Al₂O₃–SiO₂ not only offers high surface area (122 m² g) for Ni, but also changes the crystal morphology of the metal. 9 mmol/g of H₂ and 3.5 mmol/g of CH₄ were produced at the conditions that 5.0 wt% alkaline lignin plus 1 g/g Ni/Al₂O₃–SiO₂ operating for 30 min at 550 °C. A kinetic model was also developed, and the activation energies of gas and char formation were calculated to be 36.68 ± 0.22 and 9.0 ± 2.4 kJ/mol, respectively. Although the loss of activity surface area during reuse caused slight activity reduction in Ni/Al₂O₃–SiO₂, the catalyst system still possessed high catalytic activity in generating H₂ and CH₄. It is noted that sulfur linkage could be hydrolyzed to hydrogen sulfide in the gasification process of alkaline lignin. The stable chemical states of Ni/Al₂O₃–SiO₂ grants its insensitivity to sulfur, suggesting that Ni/Al₂O₃–SiO₂ should be economically promising for sub/supercritical water gasification of biomass in the presence of sulfur.     

Synthesis of bimetallic PtPd nanocubes on graphene with N,N-dimethylformamide and their direct use for methanol electrocatalytic oxidation

Bimetallic PtPd nanocubes supported on graphene nanosheets (PtPdNCs/GNs) were prepared by a rapid, one-pot and surfactant-free method, in which N,N-dimethylformamide (DMF) was used as a bi-functional solvent for the reduction of both metal precursors and graphene oxide (GO) and for the surface confining growth of PtPdNCs. The morphology, structure and composition of the thus-prepared PtPdNCs/GNs were characterized by transmission electron microscopy (TEM), high resolution TEM, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. Because no surfactant or halide ions were involved in the proposed synthesis, the prepared PtPdNCs/GNs were directly modified onto a glassy carbon electrode and showed high electrocatalytic activity for methanol oxidation in cyclic voltammetry without any pretreatments. Moreover, with the synergetic effects of Pt and Pd and the enhanced electron transfer by graphene, the PtPdNCs/GNs composites exhibited higher electrocatalytic activity (j_p = 0.48 A mg⁻¹) and better tolerance to carbon monoxide poisoning (I_f/I_b = 1.27) compared with PtPd nanoparticles supported on carbon black (PtPdNPs/C) (j_p = 0.28 A mg⁻¹; I_f/I_b = 1.01) and PtNPs/GNs (j_p = 0.33 A mg⁻¹; I_f/I_b = 0.95). This approach demonstrates that the use of DMF as a solvent with heating is really useful for reducing GO and metal precursors concurrently for preparing clean metal–graphene composites.     

Non-metal catalytic synthesis of graphene from a polythiophene monolayer on silicon dioxide

Direct synthesis of graphene without metal catalysts on a dielectric substrate is a major goal in graphene-based electronics and is an increasingly popular nanotechnology alternative to metal oxide semiconductor technology. However, current methods for the synthesis of these graphenes have many limitations, including the use of metal catalyst. Herein, we report a facile approach to the direct synthesis of graphene sheets based on the self-assembled monolayers (SAMs) technique. The new method for metal catalyst-free direct synthesis of a graphene sheet is through a solution-processable, inexpensive, easy, and reproducible cross-linked polythiophene self-assembled monolayer (SAM) that is formed via the [4 + 2] π cycloaddition reaction of π-electron conjugated thiophene layer self-assembled on the dielectric silicon dioxide substrate. The bifunctional molecules were carefully designed to create an SAM via silanization of alkoxy silane groups on the SiO₂ substrate, and at the other end, a thin cross-linked polythiophene layer via a [4 + 2] π-electron cycloaddition reaction of π-electron conjugated thiophene SAM. By heating the cross-linked polythiophene SAM up to 1000 °C under a high vacuum, single-layered or few-layered graphene sheets were successfully prepared on the dielectric silicon oxide substrate.     

Grafting of epoxy chains onto graphene oxide for epoxy composites with improved mechanical and thermal properties

Epoxy composites filled with both graphene oxide (GO) and diglycidyl ether of bisphenol-A functionalized GO (DGEBA–f–GO) sheets were prepared at different filler loading levels. The correlations between surface modification, morphology, dispersion/exfoliation and interfacial interaction of sheets and the corresponding mechanical and thermal properties of the composites were systematically investigated. The surface functionalization of DGEBA layer was found to effectively improve the compatibility and dispersion of GO sheets in epoxy matrix. The tensile test indicated that the DGEBA–f–GO/epoxy composites showed higher tensile modulus and strength than either the neat epoxy or the GO/epoxy composites. For epoxy composite with 0.25 wt% DGEBA–f–GO, the tensile modulus and strength increased from 3.15 ± 0.11 to 3.56 ± 0.08 GPa (∼13%) and 52.98 ± 5.82 to 92.94 ± 5.03 MPa (∼75%), respectively, compared to the neat epoxy resin. Furthermore, enhanced quasi-static fracture toughness (K_IC) was measured in case of the surface functionalization. The GO and DGEBA–f–GO at 0.25 wt% loading produced ∼26% and ∼41% improvements in K_IC values of epoxy composites, respectively. Fracture surface analysis revealed improved interfacial interaction between DGEBA–f–GO and matrix. Moreover, increased glass transition temperature and thermal stability of the DGEBA–f–GO/epoxy composites were also observed in the dynamic mechanical properties and thermo-gravimetric analysis compared to those of the GO/epoxy composites.     

Direct multipulse laser processing of titanium oxide–graphene oxide nanocomposite thin films

Nanocomposite thin films consisting of titanium oxide (TiO₂) nanoparticles (NPs) and graphene oxide (GO) platelets were deposited by a spin-coating technique. The obtained films were submitted to direct laser irradiation using a frequency quadrupled Nd:YAG (λ=266 nm, τ_FWHM≅3 ns, ν=10 Hz) laser source. The effect of the laser processing conditions, as laser fluence value and number of subsequent laser pulses incident onto the same target location, on the surface morphology, crystalline structure, and chemical composition of the TiO₂/GO nanocomposite thin films was systematically investigated. The laser fluence values were maintained below the vaporization threshold of the irradiated composite material. With the increase of the laser fluence and number of incident laser pulses melting and coalescence of the TiO₂ NPs into inter-connected aggregates as well as rippling of the GO platelets take place. The gradual reduction of GO platelets and the onset of anatase to rutile phase transition were observed at high laser fluence values.     

Effect of graphene addition on the mechanical and electrical properties of Al2O3-SiCw ceramics

This paper presents a study on graphene-reinforced Al₂O₃-SiCw ceramic composites and the relationship between graphene oxide (GO) loading and the resulting mechanical and electrical properties. Well-dispersed ceramic-GO powders were fabricated using a colloidal processing route. Dense composites were obtained via spark plasma sintering, a technique that has the ability to reduce GO to graphene in situ during the sintering process. The mechanical properties of the sintered composites were investigated. The composite with only a small amount of graphene (0.5 vol.%) showed the highest flexural strength (904 ± 56 MPa), fracture toughness (10.6 ± 0.3 MPa·m^1/2) and hardness (22 ± 0.8 GPa) with an extremely good dispersion of graphene within the ceramic matrix. In addition to these exceptional mechanical properties, the sintered composites also showed high electrical conductivity, which allows the compacts to be machined using electrical discharge machining and thus facilitates the fabrication of ceramic components with sophisticated shapes while reducing machining costs.     

EELS study of the epitaxial graphene/Ni(1 1 1) and graphene/Au/Ni(1 1 1) systems

We have performed electron energy-loss spectroscopy (EELS) studies of Ni(1 1 1), graphene/Ni(1 1 1), and the graphene/Au/Ni(1 1 1) intercalation-like system at different primary electron energies. A reduced parabolic dispersion of the π plasmon excitation for the graphene/Ni(1 1 1) system is observed compared to that for bulk pristine and intercalated graphite and to linear for free graphene, reflecting the strong changes in the electronic structure of graphene on Ni(1 1 1) relative to free-standing graphene. We have also found that intercalation of gold underneath a graphene layer on Ni(1 1 1) leads to the disappearance of the EELS spectral features which are characteristic of the graphene/Ni(1 1 1) interface. At the same time the shift of the π plasmon to the lower loss-energies is observed, indicating the transition of initial system of strongly bonded graphene on Ni(1 1 1) to a quasi free-standing-like graphene state.