Corrosion fatigue crack growth behavior of oil-grade nickel-base alloy 718. Part 1: Effect of corrosive environment

The effect of corrosive environment on corrosion fatigue crack growth (CFCG) behavior of oil-grade nickel-base alloy 718 is studied. The results demonstrate that there is no obvious effect of 3.5 wt.% NaCl solution at RT, 50 °C and 80 °C on CGCG rates while 21 wt.% NaCl solution at 80 °C produces a deleterious effect on CFCG rates compared to the ones tested in air. Potentiodynamic polarization results show that alloy 718 exhibits passive behavior in 3.5 wt.% NaCl solution, while pitting corrosion resistance decreases with increasing solution temperature. Nevertheless, alloy 718 shows active corrosion behavior in 21 wt.% NaCl solution at 80 °C.     

Study of the correlation between pitting corrosion and the component ratio of the dual phase in duplex stainless steel welds

Three duplex stainless steel weldments were produced by changing the chromium element to study the correlation between the pitting corrosion characteristics and the component ratio of the dual phase. The pit morphologies showed that metastable pits were generated at a lower pitting resistance equivalent number (PREN) phase. The secondary austenite phases seemed to serve as a path for the corrosive environment regardless of the ferrite number (FN). There is some discrepancy between the measured values (pitting potential (E_p) through polarization test) and expected values (sequence ranked by PREN of weaker phase) in 1 mol l⁻¹ NaCl solution at 60 °C.     

Corrosion behavior of Cu–Al–Be shape memory alloys with different compositions and microstructures

The corrosion behavior of Cu–Al–Be shape memory alloys with different microstructures and Be content in a 3.5% NaCl solution was studied by weight loss, cyclic anodic polarization and chronoamperometric measurements. The beryllium has a beneficial effect in β alloys. A pitting potential of −100 mV/SCE was found by anodic polarization tests for all the studied alloys, corresponding to the formation of pits produced by severe dealuminization. Samples with precipitates were more susceptible to pit formation. The corrosion behavior is strongly affected by the alloy microstructural conditions, and the β samples present higher pitting resistance and repassivation ability.     

Atmospheric corrosion of field-exposed AZ31 magnesium in a tropical marine environment

Corrosion behavior of AZ31 magnesium in tropical marine atmosphere was investigated. Chloride ions deposition rate played an important role in the corrosion process, which resulted in an obvious fluctuation of the corrosion rate. The corrosion was initiated from pitting corrosion and then evolved into general corrosion as the exposure time extended. Mg₅(CO₃)₄(OH)₂·xH₂O was the dominate products during the whole exposure periods. The products on the specimens weathered for 1, 6 and 12 months slightly suppressed the corrosion process, while that generated after 24 months of exposure exhibited good protective ability against further corrosion attacks.     

Corrosion inhibition by anionic surfactants of AA2198 Li-containing aluminium alloy in chloride solutions

This paper evaluates the inhibiting action of some anionic surfactants towards AA2198 corrosion in NaCl solutions; the effect of surfactant concentration in relation to chloride amount was determined.On separate electrodes, polarization curves were recorded after 1, 24 and 168 h immersion in the aggressive media, while EIS technique continuously monitored the alloy corrosion process.In general, these substances stifled both the cathodic and anodic processes and noticeably shifted the pitting potential (breakdown potential, E_BR) in the positive direction. The most efficient compounds were N-lauroylsarcosine sodium salt and sodium dodecyl-benzenesulfonate, able to withstand the effects of 0.1 M Cl⁻.     

Electrochemical behavior of a lead-free Sn–Cu solder alloy in NaCl solution

Electrochemical impedance spectroscopy (EIS), potentiodynamic polarization techniques and an equivalent circuit analysis are used to evaluate the electrochemical corrosion behavior of Sn–Cu alloy samples in a naturally aerated 0.5 M NaCl solution at 25 °C. It has been found that a better electrochemical corrosion resistance is provided by a coarser cellular microstructure array. It has also been found that the corrosion current density (i_corr) is of about a quarter when compared with that of the finest microstructure examined. Such behavior is attributed to both localized strains between the Sn-rich phase and intermetallic (IMC) particles and the cathode/anode area ratios. The effect of copper alloying on i_corr is also discussed.     

Application of automated electrical resistance sensors for measurement of corrosion rate of copper,bronze and iron in model indoor atmospheres containing short-chain volatile carboxylic acids

The corrosion rate of copper and bronze Cu-8 wt.%Sn increased rapidly when the concentration of formic or acetic acid in air reached about 300 ppb at 80% relative humidity (RH) and a temperature of 20 °C. It decreased slowly during the several days after pollutant removal due to the slow rate of pollutant desorption from the metal surfaces. Corrosion of these metals was barely affected by the acids at RH up to 60%. For iron, the critical concentration of formic acid in air which led to surface activation at 80% RH was between 1000 and 1590 ppb.     

A method for investigation of hot corrosion by gaseous Na2SO4

A novel in situ exposure method for investigating hot corrosion of aluminde coatings in the absence of an alkali sulphate melt is presented. The samples are exposed to Na₂SO₄(g) at a temperature above the dew point of the gas. Results from 100 and 500 h exposures at 900 °C of Ni-based In792 covered with SIF232 aluminide coating are presented. Already after 100 h of testing, attack characteristic for Type I hot corrosion is observed. The reactions taking place during the testing are discussed and the results are compared with those from the well-known ex situ salt hot corrosion test.     

Electrochemical study of the corrosion of different alloys exposed to deaerated 80 °C geothermal brines containing CO2

Corrosion of metallic engineering materials accounts for problems during geothermal operation in the Upper Rhine Graben (URG). Herein, we study the electrochemical behaviour of various metal alloys in an 80 °C simulated geothermal environment by using potentiodynamic polarisation and open-circuit potential measurements. Two different natural geothermal waters from URG geothermal sites were used for the experiments. The measurements reveal spontaneous passivation to be a key process for all alloys. This ennoblement protects more noble alloys from significant corrosion (e.g. titanium gr. 2, alloy 625) and brings less noble alloys to failure, mostly due to pitting corrosion (e.g. 316L).     

Corrosion of ultra-high-purity Mg in 3.5% NaCl solution saturated with Mg(OH)2

Corrosion was evaluated for ultra-high-purity magnesium (Mg) immersed in 3.5% NaCl solution saturated with Mg(OH)₂. The intrinsic corrosion rate measured with weight loss, P_W = 0.25 ± 0.07 mm y⁻¹, was slightly smaller than that for high-purity Mg. Some specimens had somewhat higher corrosion rates attributed to localised corrosion. The average corrosion rate measured from hydrogen evolution, P_AH, was lower than that measured with weight loss, P_W, attributed to dissolution of some hydrogen in the Mg specimen. The amount of dissolution under electrochemical control was a small amount of the total dissolution. A new hydride dissolution mechanism is suggested.     

Passivity of Sanicro28 (UNS N-08028) stainless steel in polluted phosphoric acid at different temperatures studied by electrochemical impedance spectroscopy and Mott–Schottky analysis

Corrosion resistance of a highly alloyed austenitic stainless steel (Sanicro28) in 50 wt.% H₃PO₄ industrial medium containing impurities at temperatures from 20 °C to 80 °C was evaluated after different immersion times. Electrochemical measurements (polarization curves, OCP, EIS and Mott–Schottky) demonstrated that Sanicro28 passivates spontaneously. From impedance results, film thicknesses of about 1.6–4.5 nm were obtained. At low temperature, the resistance to corrosion increases with immersion time due to the formation of iron phosphate and/or chromium phosphate. At higher temperature, phosphate formed a porous polyphosphate film identified by μ-Raman. No pits are initiated on surface whatever the temperature.     

Design and synthesis of a novel class of inhibitors for mild steel corrosion in acidic and carbon dioxide-saturated saline media

p-(9-(2-Methylisoxazolidin-5-yl)nonyloxy)benzaldehyde I, prepared using a cycloaddition protocol, was elaborated into its cinnamaldehyde derivative II which upon quarternization with propargyl chloride afforded III bearing an interesting blend of structural traits suitable for imparting inhibition of mild steel corrosion. Novel compounds I–III showed efficient inhibition against mild steel corrosion in CO₂–0.5 M NaCl (40 °C, 1 atm; 120 °C, 10 bar), 1, 4, 7.7 M HCl, and 0.5 M H₂SO₄ at 60 °C as determined by gravimetry and electrochemical methods. The presence of carbonaceous surface and nitrogen, as revealed by XPS study, indicated the formation of a film covering the metal surface, which imparted corrosion inhibition.     

Effect of alloyed molybdenum on corrosion behavior of plasma immersion nitrogen ion implanted austenitic stainless steel

Plasma immersion ion implantation (PIII) of nitrogen has been performed on two austenitic stainless steels (with and without Mo addition) at three different temperatures namely, 250, 380 and 500 °C for 3 h. Grazing angle X-ray diffraction (GXRD) was carried out on the surface of the steels (both PIII treated and untreated). GXRD results suggest that PIII is more effective in Mo containing stainless steel (SS). The electrochemical corrosion studies examined through both by DC polarization and EIS technique in 3.5 wt.% NaCl reveals that, 3 h N-implantation at 250 and 380 °C improves the corrosion and pitting resistance of both the austenitic stainless steels under investigation. The effect N implantation on pitting resistance is seen more in the presence of Mo, than when it is not present in the SS. It is further emphasized that the pitting resistance of the alloys significantly deteriorates, when they are implanted at 500 °C.     

Effect of N and C on stress corrosion cracking susceptibility of austenitic Fe18Cr10Mn-based stainless steels

Stress corrosion cracking (SCC) susceptibility of austenitic Fe18Cr10Mn alloys with 0.3N, 0.6N and 0.3N0.3C was investigated in aqueous chloride environment using a slow strain rate test method. The SCC susceptibility of Fe18Cr10Mn alloys in 2 M NaCl solution at 50 °C under constant anodic potential condition decreased with increase in N content from 0.3 to 0.6 wt%, and with addition of 0.3 wt% C to the Fe18Cr10Mn0.3N alloys. The present study strongly suggested that the beneficial effects of N and C on the SCC behavior of Fe18Cr10Mn alloys would be associated with the resistance to pitting corrosion initiation and the repassivation kinetics.     

Ultrafine-grained copper produced by machining and its unusual electrochemical corrosion resistance in acidic chloride pickling solutions

Ultrafine-grained (UFG) copper was prepared by facile machining procedure. High resolution transmission electron microscopy images revealed that, in UFG Cu, minimum grain size of 80 nm could be formed when a small machining rake angle was applied. The electrochemical corrosion behavior of UFG Cu in 0.5 M HCl was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy. Comparing with coarse-grained Cu, UFG Cu exhibited notably declined corrosion current density. Particularly, when the size of Cu grains were reduced from 500 μm to 80 nm, the charge transfer resistance of anodic dissolution step dramatically increased from 200 to 621 Ω cm².     

Role of chlorides on pitting and hydrogen embrittlement of Mg–Mn wrought alloy

The role of chlorides on stress corrosion cracking behavior of Mg–Mn hot rolled alloy was studied in Mg(OH)₂ saturated, 0.01 M and 0.1 M NaCl solutions. The alloy was found to fail by hydrogen embrittlement mechanism both in presence and absence of chlorides. However, the role of chloride has been found to be to damage the passive film, cause pitting and increasing hydrogen embrittlement tendency of the alloy. Crack initiation occurred through pitting and grew in a transgranular manner involving hydrogen.     

Corrosion of the Heat-Affected Zones (HAZs) of API-X100 pipeline steel in dilute bicarbonate solutions at 90 °C – An electrochemical evaluation

This research explores for key correlations between the microstructures of API-X100 steel HAZs, simulated by Gleeble© thermal cycles, and their electrochemical corrosion behavior in dilute bicarbonate solutions at 90 °C. The potentiodynamic polarization revealed the role of ferrite of a HAZ cooled at 10 °C/s with the lowest passive currents, and those of acicular ferrite and martensite of the 30 and 60 °C/s HAZs with unstable, thin passivation. The 0.5 V vs. SCE potentiostatic currents suggested also a slow passivation growth, of repetitive breakdowns and repassivations, for the 30 and 60 °C/s HAZs. EIS equivalent circuits and time-dependent interfaces were proposed for each of the HAZ microstructures.     

High temperature oxidation of AlCrFe complex metallic alloys

Isothermal oxidation of Al₆₅Cr₂₇Fe₈ and Al₈₀Cr₁₅Fe₅ was studied in the 600–1080 °C range. Formation of transient alumina layers is obtained up to 900 °C. On Al₆₅Cr₂₇Fe₈ transient to α-phase transformations occur when performing oxidation at 1000 °C, together with the possible appearance of (Al_0.9Cr_0.1)₂O₃. At 1080 °C, direct formation of α-alumina is obtained. On Al₈₀Cr₁₅Fe₅, spallation of the oxide layer during the cooling stage is observed following oxidation at 800 and 900 °C, revealing thermal etching of the underneath alloy surface. At 1050 °C the α-Al₂O₃ scale is directly formed but plastic deformation and recrystallization of the underneath alloy into several intermetallic phases is observed.     

Adsorption and corrosion inhibition of phytic acid calcium on the copper surface in 3 wt% NaCl solution

The adsorption and corrosion protection effect of phytic acid calcium (PAC) film on the copper surface in 3 wt% NaCl solution was investigated using potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Raman spectroscopy. Polarization curves indicate that PAC is a mixed inhibitor, affecting both cathodic and anodic corrosion currents. The inhibition efficiency of PAC film reached 92.53% at an optimized condition. Adsorption of PAC molecules on the surface followed Langmuir adsorption isotherm and the standard Gibbs energy of −37.32 kJ mol⁻¹ indicated a chemisorptive way. Raman studies suggested that PAC molecule chemically anchored at the surface via PO groups.