Crystallization of Ultrafine Amorphous Si3N4 During Sintering

Ultrafine amorphous Si₃N₄ powders were synthesized from laser-heated gases and cold-pressed into pellets for sintering experiments. At temperatures >1300°C, the powders crystallized with a concurrent, linearly proportional decrease in surface area. These powders densified on a local scale without additives or pressure.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.     

Solubility of Si3N4 in Liquid SiO2

The nitrogen solubility in the SiO₂-rich liquid in the metastable binary SiO₂-Si₃N₄ system has been determined by analytical TEM to be 1%–4% of N/(O + N) at 1973–2223 K. Analysis of the near edge structure of the electron energy loss peak indicates that nitrogen is incorporated into the silicate network rather than being present as molecular N₂. A regular solution model with a positive enthalpy of mixing for the liquid was used to match the data for the metastable solubility of N in the presence of crystalline Si₃N₄ and to adjust the computed phase diagram. The solubility of Si₃N₄ in fused SiO₂ is far less than reported in liquid silicates also containing Al, Mg, and/or Y. Apparently, these cations act as modifiers that break anion bridges in the silicate network and, thereby, allow further incorporation of Si₃N₄ without prohibitive amounts of network cross-linking. Finally, indications emerged regarding the diffuse nature of the Si₃N₄-SiO₂ interface that leads to amorphous regions of higher N content.     

Comparison of Tribological Behavior Between α-Sialon/Si3N4 and Si3N4/Si3N4 Sliding Pairs in Water Lubrication

We report here the study on tribological behavior of α-Sialon in aqueous medium. The results derived from a wide range of test conditions are briefly discussed. A reduction in friction coefficient from 0.7 to 0.03 and a decrease in wear rate by two orders of magnitude were achieved under low load (9.8 N) and high speed (>0.54 m/s) conditions. The tribological behavior of α-Sialon/Si₃N₄ ceramics was then compared with Si₃N₄/Si₃N₄ tribopairs.     

Sintering of Si3N4 with the Addition of Rare-Earth Oxides

The effect of rare-earth oxide additives on the densification of silicon nitride by pressureless sintering at 1600° to 1700°C and by gas pressure sintering under 10 MPa of N₂ at 1800° to 2000°C was studied. When a single-component oxide, such as CeO₂, Nd₂O₃, La₂O₃, Sm₂O₃, or Y₂O₃, was used as an additive, the sintering temperature required to reach approximate theoretical density became higher as the melting temperature of the oxide increased. When a mixed oxide additive, such as Y₂O₃–Ln₂O₃ (Ln=Ce, Nd, La, Sm), was used, higher densification was achieved below 2000°C because of a lower liquid formation temperature. The sinterability of silicon nitride ceramics with the addition of rare-earth oxides is discussed in relation to the additive compositions.     

Preparation of High-Density Si3N4 by a Gas-Pressure Sintering Process

Si₃N₄ compacts, containing ≅7 wt% of both BeSiN₂ and SiO₂ as densification aids, can be reproducibly sintered to relative densities >99% by a gas-pressure sintering process. Nearly all densification takes place via liquid-phase sintering of transformed β-Si₃N₄ grains at T =1800° to 2000°C. Compacts with high density are produced by first sintering to the closed-pore stage (≅92% relative density) in 2.1 MPa (20 atm) of N₂ pressure at 2000°C and then increasing the N₂ pressure to 7.1 MPa (70 atm) where rapid densification proceeds at T = 1800° to 2000°C. The experimental density results are interpreted in terms of theoretical arguments concerning the growth (coalescence) of gas-filled pores and gas solubility effects. Complex chemical reactions apparently occur at high temperatures and are probably responsible for incomplete understanding of some of the experimental data.     

Volatilization Associated with the Sintering of Polyphase Si3N4 Materials

Weight loss which occurs while sintering composited Si₃N₄ powders requires the loss of one or more of the end-member constituents through a volatilization reaction. By plotting the direction of the compositional change on the appropriate equivalence phase diagram, the principal volatilization reaction can be determined. For a particular composition in the system Si-Y-N-O sintered at 1750°C, the principal volatilization reaction was Si₃N₄(s) +3SiO₂(s)→6SiO(g) +2N₂(g).     

Hot-Pressing Behavior of Si3N4

The densification behavior of Si₃N₄ containing MgO was studied in detail. It was concluded that MgO forms a liquid phase (most likely a magnesium silicate). This liquid wets and allows atomic transfer of Si₃N₄. Evidence of a second-phase material between the Si₃N₄ grains was obtained through etching studies. Transformation of α- to β-Si₃N₄ during hot-pressing is not necessary for densification.     

Properties of Si3N4 Produced by Nitriding Slip-Cast Si Containing Si3N4 Grog Additions

The properties of Si₃N₄ compositions produced by nitriding slip-cast Si bodies containing up to 16% Si₃N₄ grog were determined. The introduction of grog consistently lowered the densities, the room- and high-temperature strengths, and the resistance to oxidation. The open structure of the grog-containing mixes favored low-temperature gas-phase reactions leading to α-Si₃N₄ formation. In higher-density compositions containing predominantly Si, gas-liquid-solid reactions at higher temperatures produced a relatively greater content of the β phase.     

Pressureless Sintering of Si3N4 Ceramic Using AlN and Rare-Earth Oxides

Using intermediate, liquid-forming compositions in the (Y,La)₂O₃-AlN system as additives, fully dense Si₃N₄ ceramics with high strength at high temperature have been obtained by pressureless sintering. The ceramics contain rod-shaped β-Si₃N₄ with M' or K' solid solutions as grain-boundary phases. The strength of these ceramics is 1150 MPa at 1200°C, and the room-temperature toughness is maintained at }7 MPa·m^1/2. Phase relations that are pertinent to the new additive compositions are delineated to rationalize their beneficial effects on sinterability and mechanical properties.     

Oxidation of Si3N4 Alloys: Relation to Phase Equilibria in the System Si3N4-SiO2-MgO

The oxidation resistance at 1400°C of silicon nitride alloys hot-pressed with magnesia was investigated as a function of the phase content of the alloys. The extent of oxidation, the products of oxidation, their stratification, and the continuity of the oxide scale are all dependent on the initial composition. Also, the compositions of the alloys themselves change during oxidation. The findings can be interpreted on the basis of compositional paths in the equivalence phase diagram. Reasons for the outward diffusion of Mg and impurities are given and the effect of the secondary phase on oxidation kinetics is discussed.     

Oxidation and Strength Retention of Monolithic Si3N4 and Nanocomposite Si3N4-SiC with Yb2O3 as a Sintering Aid

The oxidation behaviors of monolithic Si₃N₄ and nanocomposite Si₃N₄-SiC with Yb₂O₃ as a sintering aid were investigated. The specimens were exposed to air at temperatures between 1200° and 1500°C for up to 200 h. Parabolic weight gains with respect to exposure time were observed for both specimens. The oxidation products formed on the surface also were similar, i.e., a mixture of crystalline Yb₂Si₂O₇ and SiO₂ (cristobalite). However, strength retention after oxidation was much higher for the nanocomposite Si₃N₄-SiC compared to the monolithic Si₃N₄. The SiC particles of the nanocomposite at the grain boundary were effective in suppressing the migration of Yb³⁺ ions from the bulk grain-boundary region to the surface during the oxidation process. As a result, depletion of yttribium ions, which led to the formation of a damaged zone beneath the oxide layer, was prevented.