Thermoelectric properties of WO<Subscript>3</Subscript>-based ceramics doped with Co<Subscript>2</Subscript>O<Subscript>3</Subscript>

Tungsten trioxide (WO₃) doped with cobalt sesquioxide (Co₂O₃) was prepared by a conventional mixed oxide processing route and the thermoelectric properties were studied from 300 up to 1,000 K. The addition of Co₂O₃ to WO₃ resulted in an increase in both the grain size and porosity, indicating that Co₂O₃ promotes the grain grown of WO₃. The magnitude of the electrical conductivity (σ) and the absolute value of the Seebeck coefficient (|S|) depended strongly on the Co₂O₃ content. As for the power factor (σS ² ), the 5.0 mol% sample has the maximum value of the power factor which is 0.12 μWm⁻¹K⁻² at 873 K.     

Elastic properties of Na<Subscript>2</Subscript>O-ZnO-ZnF<Subscript>2</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> oxyfluoride glasses

Elastic properties of Na₂O-ZnO-ZnF₂-B₂O₃ oxyfluoride glasses with different ZnF₂ concentrations have been investigated using ultrasonic velocity measurements at room temperature, at a frequency of 10 MHz. Glasses prepared by melt quenching method were suitably polished for the ultrasonic velocity measurements using pulse-echo superposition method. Various elastic moduli have been calculated and their compositional dependence has been examined. The compositional dependence of elastic moduli with the concentration of ZnF₂ shows decrease in the moduli initially, with further increase in ZnF₂ the moduli sharply increases and then again tend to decrease when ZnF₂ concentration is 20 mol%. The values of Poisson’s ratio lie in the range of 0·24–0·30, which is typical to covalent bonded network. The variation of θ _D with ZnF₂ indicates complex behaviour of the glass network. The results have been analysed in view of the modified borate glass network. Addition of ZnF₂ into the pure glass seems to influence the borate network by replacement of B-O-B linkages with B-O-Zn.     

Synthesis and structural studies of Na<Subscript>2</Subscript>O-ZnO-ZnF<Subscript>2</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> oxyfluoride glasses

This paper describes the synthesis and spectroscopic studies of the glass system, 20Na₂O-(20-x) ZnO-xZnF₂-60B₂O₃(x = 0, 5, 10, 15, 20), prepared by melt quenching method. The analyses of DSC and XRD did not show the crystallinity of the glass sample. ¹¹B MAS-NMR shows the presence of sharp peak around −14 ppm. From the IR studies, the broadening of the peak around 1200–1400 and 800–1100 cm⁻¹ shows the presence of mixed linkages like B-O-B, B-O-Zn in the network.     

Ceramics Based on Powder Mixtures Containing Calcium Hydrogen Phosphates and Sodium Salts (Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>, Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>, and NaPO<Subscript>3</Subscript>)

Ceramic materials in the Na₂O–CaO–P₂O₅ system have been produced using powder mixtures containing calcium hydrogen phosphates (monetite/brushite: CaHPO₄/CaHPO₄ ? 2H₂O) and sodium salts (Na₂CO₃ ? H₂O, Na₄P₂O₇ ? 10H,O, and NaPO₃). These salts were used as precursors to the following high-temperature phases: Сa₂P₂O₇, Na₂O, Na₄P₂O₇, and NaPO₃. The amount of the salts in the powder mixtures was such that the oxide composition of the ceramics corresponded to 10 mol % sodium oxide for each mixture in the Na₂O–CaO–P₂O₅ system. The powder mixtures were prepared using mechanical activation in acetone, which was accompanied by monetite rehydration to brushite. X-ray diffraction characterization showed that, after firing, the phase composition of the ceramics produced from the powder mixtures thus prepared lay in the Сa₂P₂O₇–NaCaPO₄–Na₂СaP₂O₇–Са(РО₃)₂ phase field. The resultant ceramic materials contain biocompatible and bioresorbable phases and can be recommended for bone implant fabrication.     

Temperature-stable and low loss Fe-containing dielectrics in BaO-Ln<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Polycrystalline samples of Ba₄Ln₂Fe₂Ta₈O₃₀ (Ln = La and Nd) were prepared by a high temperature solid-state reaction technique. The formation, structure, dielectric and ferroelectric properties of the compounds were studied. Both compounds are found to be paraelectrics with filled tetragonal tungsten bronze (TB) structure at room temperature. Dielectric measurements revealed that the present ceramics have exceptional temperature stability, a relatively small temperature coefficient of dielectric constant (τ _ε ) of −25 and −58 ppm/°C, with a high dielectric constant of 118 and 96 together with a low dielectric loss of 1.2 × 10⁻³ and 2.8 × 10⁻³ (at 1 MHz) for Ba₄La₂Fe₂Ta₈O₃₀ and Ba₄Nd₂Fe₂Ta₈O₃₀, respectively. The measured dielectric properties indicate that both materials are possible candidates for the fabrication of discrete multilayer capacitors in microelectronic technology.     

Thermal Analysis of the Ternary System Li<Subscript>2</Subscript>WO<Subscript>4</Subscript>-WO<Subscript>3</Subscript>-Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>

Thermal analysis results indicate that the liquidus surface of the Li₂WO₄-WO₃-Li₂B₄O₇ system consists of the primary phase fields of Li₂WO₄, Li₂B₄O₇, WO₃, Li₂WO₄ · WO₃ (congruent melting), 3Li₂WO₄ · 2Li₂B₄O₇ (congruent melting), and Li₂WO₄ · 3WO₃ (incongruent melting). Low-melting-point compositions are selected that are potentially attractive for the low-temperature synthesis of lithium tungsten bronze powders.     

Preparation and characterization of bioactive sol-gel-derived Na<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>9</Subscript>

In this study, pure Na₂Ca₂Si₃O₉ was synthesized by a sol-gel method, and Na₂Ca₂Si₃O₉ cuboids and disks were prepared by uniaxial pressing and calcining at 700 °C. The porosity and mechanical strength of the Na₂Ca₂Si₃O₉ cuboids were measured, and the results showed that the Na₂Ca₂Si₃O₉ cuboids were porous with an average porosity of 44%, and the 3-point bending strength of the cuboids was 6.08 MPa. The in vitro bioactivity of Na₂Ca₂Si₃O₉ was carried out by soaking Na₂Ca₂Si₃O₉ disks in simulated body fluid (SBF). The results showed that hydroxyapatite (HA) formed on the surface of Na₂Ca₂Si₃O₉ samples after soaking for 1 day, which indicated good bioactivity of Na₂Ca₂Si₃O₉.     

Subsolidus phase relations in the system Tm<Subscript>2</Subscript>O<Subscript>3</Subscript>-Rh<Subscript>2</Subscript>O<Subscript>3</Subscript>

The Tm₂O₃-Rh₂O₃ system has been studied by x-ray diffraction, thermal analysis, and chemical analysis of annealed and quenched samples. The results have been used to construct a schematic subsolidus phase diagram of the system. Only one double oxide, TmRhO₃, has been identified. Some of its physicochemical properties are reported.     

Characterization and electrical properties of semiconducting Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

Semiconducting glasses of the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system were prepared by the press-quenching method and their dc conductivity in the temperature range 223–393 K was measured. The glass transition temperature values (T_g) of the present glasses were larger than those of tellurite glasses. This indicates a higher thermal stability of the glass in the present system. The density for these glasses was consistent with the ionic size, atomic weight and amount of different elements in the glasses. Mössbauer results revealed that the relative fraction of Fe increases with increasing Fe₂O₃ content. Electrical conductivity showed a similar composition dependency as the fraction of Fe. The glasses had conductivities ranging from 10 to 10 Scm at temperatures from 223 to 393 K. Electrical conduction of the glasses was confirmed to be due to non-adiabatic small polaron hopping and the conduction was primarily determined by hopping carrier mobility.     

Glass formation in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-BaO system

The physicochemical properties of BaO-Bi₂O₃-B₂O₃ glasses have been studied. The effect of KBF₄ additions on the properties of the glasses has been examined. The transmission of the glasses has been correlated with their local structure and composition.     

Electrical conductivity of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-Tm<Subscript>2</Subscript>O<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> solid solutions

New solid solutions, Bi_2?x?y Tm _x Nb _y O_3+δ, with tetragonal and cubic structures have been synthesized in the Bi₂O₃-Tm₂O₃-Nb₂O₅ system, and their electrical conductivity has been measured at temperatures from 670 to 1020 K. The 1020-K conductivity of the tetragonal solid solution Bi_1.8Tm_0.15Nb_0.05O_3+δ is comparable to that of Bi_1.75Tm_0.25O₃, the best conductor in the Bi₂O₃-Tm₂O₃ system.     

Calcium bismuth borates in the CaO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The 600°C (subsolidus) section of the CaO-Bi₂O₃-B₂O₃ phase diagram has been studied by x-ray diffraction and differential thermal analysis. A new calcium bismuth borate of composition CaBi₂B₄O₁₀ has been identified, and the existence of CaBi₂B₂O₇ has been confirmed. According to T-x phase diagram data, these compounds form peritectically at 700±5 and 783±5°C, respectively.     

Effects of sodium oleate on synthesis and photocatalytic activity of Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript>/Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>@RGO

In this study, the effects of sodium oleate on synthesis of Bi₂WO₆/Bi₂O₃ loaded reduced graphene oxide photocatalyst was studied. The as-prepared composites were characterized by X-ray diffraction, Fourier transform infrared, X-ray photoelectron spectroscopy, UV–visible diffuse reflectance and photoluminescence spectroscopy. The results suggested that addition of sodium oleate not only promoted synthesis of Bi₂O₃, but also enhanced the reduction of GO to graphene. When the amount of sodium oleate was 4 mol (Bi:SO?=?1:1), Bi₂WO₆/Bi₂O₃@RGO to the best visible-light photocatalytic activity can be synthesized by a facile one-step solvothermal process without further reduction reaction. Hence, it indicated that sodium oleate could affect the synthesis of the as-prepared composites and the photocatalytic activity for degradation of RhB. This study did provide not only a facile method to synthesize Bi₂WO₆/Bi₂O₃@RGO, but also a method to reduce graphene oxide to graphene.     

Effect of Eu<Subscript>2</Subscript>O<Subscript>3</Subscript> doping on the crystallization behavior of BaO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

We gave studied the crystallization behavior of 30BaO · 25Bi₂O₃ · 45B₂O₃ glasses doped with Eu₂O₃ to different levels. At a Eu₂O₃ content of 7 mol % or higher, the glasses undergo volume crystallization. The only precipitating phase is a solid solution between europium and bismuth oxides. With increasing europium concentration in the glass, the structure of the crystallites changes from cubic to rhombohedral. We have investigated the morphology, physicochemical properties, and luminescence spectra of the glasses and glass-ceramics.     

Preparation of magnetic composites through SrO-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass crystallization

Glasses with nominal compositions 11SrO · 5.5Fe₂O₃ · 4.5Al₂O₃ · 4B₂O₃ (1) and 15SrO · 5.5Fe₂O₃ · 4.5Al₂O₃ · 4B₂O₃ (2) were prepared by rapidly quenching oxide melts between counterrotating steel rollers. The glasses were then heat-treated in the range 650–950°C to produce glass-ceramic samples. The samples were characterized by X-ray diffraction, electron microscopy, and magnetic measurements. The phase composition of the glass-ceramics was determined, and their microstructure and magnetic properties were studied. The annealing temperature was shown to have a strong effect on the coercivity of the materials, which reaches 650 and 570 kA/m for compositions 1 and 2, respectively.     

Dielectric relaxation and ionic conductivity studies of Na<Subscript>2</Subscript>ZnP<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Na₂ZnP₂O₇ compound was obtained by the conventional solid-state reaction. The sample was characterized by X-ray powder diffraction, infrared analysis and electrical impedance spectroscopy. The impedance plots show semicircle arcs at different temperatures and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance R _p and constant phase elements CPE. Dielectric data were analyzed using complex electrical modulus M* for the sample at various temperatures. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. The conductivity σ _d.c. follows the Arrhenius relation. The near value of activation energies obtained from the analysis of M″ and conductivity data confirms that the transport is through ion hopping mechanism, dominated by the motion of the Na⁺ ions in the structure of the investigated materials.     

Y<Subscript>2</Subscript>O<Subscript>3</Subscript> and Nd<Subscript>2</Subscript>O<Subscript>3</Subscript> co-stabilized ZrO<Subscript>2</Subscript>-WC composites

Y₂O₃ + Nd₂O₃ co-stabilized ZrO₂-based composites with 40 vol% WC were fully densified by pulsed electric current sintering (PECS) at 1350 °C and 1450 °C. The influence of the PECS temperature and Nd₂O₃ co-stabilizer content on the densification, hardness, fracture toughness and bending strength of the composites was investigated. The best combination of properties was obtained for a 1 mol% Y₂O₃ and 0.75 mol% Nd₂O₃ co-stabilized composite densified for 2 min at 1450 °C under a pressure of 62 MPa, resulting in a hardness of 15.5 ± 0.2 GPa, an excellent toughness of 9.6 ± 0.4 MPa.m^0.5 and an impressive 3-point bending strength of 2.04 ± 0.08 GPa. The hydrothermal stability of the 1 mol% Y₂O₃ + 1 mol% Nd₂O₃ co-stabilized ZrO₂-WC (60/40) composites was compared with that of the equivalent 2 mol% Y₂O₃ stabilized ceramic. The double stabilized composite did not degrade in 1.5 MPa steam at 200 °C after 4000 min, whereas the yttria stabilized composite degraded after less than 2000 min. Moreover, the (1Y,1Nd) ZrO₂-WC composites have a substantially higher toughness (~9 MPa.m^0.5) than their 2Y stabilized equivalents (~7 MPa.m^0.5).     

Electrical properties of perovskite-like compounds in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> system

The electrical properties of layered perovskite-like compounds with the general formula Bi _{m + 1}Fe _{m − 3}Ti₃O_{3m + 3} have been studied in relation to their physicochemical properties and structure.     

Structure of WO<Subscript>3</Subscript>-TeO<Subscript>2</Subscript> glasses

WO₃-TeO₂ glasses have been studied by quantum-chemical simulation and Raman spectroscopy. The results have been used to develop a model for the network of tungstate-tellurite glasses. The model allows one to correlate the structure and optical properties (in particular, the position and intensity of Raman bands) of the glasses with their composition. The network of the glasses is shown to be made up, for the most part, of three types of structural groups: TeO₄ trigonal dipyramids, O=TeO₂ pyramids, and O=WO₅ octahedra. Any other structural units, in particular, WO₄ tetrahedra, are unnecessary. The model for the network of WO₃-TeO₂ glasses can be used to analyze the vibrational spectra of tungstate-tellurite glasses in a broad composition range. In particular, using this model we assigned the Raman spectra of the tungstate-tellurite glasses in the range 550–950 cm^?1.     

Phase composition and microstructure of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> solid solutions prepared by self-propagating high-temperature synthesis

The combustion synthesis, microstructure, chemical composition, and phase composition of cast Al₂O₃-Cr₂O₃ materials are described. The synthesized solid solutions are based on corundum or chromia, depending on the Al₂O₃ and Cr₂O₃ contents. Using self-propagating high-temperature synthesis, a cast aluminum oxynitride is obtained for the first time.