Photocatalytic activities of AgSbO3 under visible light irradiation

A novel visible light sensitive photocatalyst, AgSbO₃ was prepared by a conventional solid-state reaction method. This oxide belonging to a cubic-pyrochlore structure can absorb visible light with wavelength up to about 480 nm. From the band structure calculation, we found that the top of the valence band consists of the hybridized Ag 4d and O 2p orbitals and the bottom of the conduction band mainly consists of the Ag 5s and the Sb 5s orbitals. Photocatalytic activities were evaluated using O₂ evolution from an aqueous silver nitrate solution and decomposition of gaseous 2-propanol under visible light irradiation. We found that AgSbO₃ shows a higher O₂ evolution activity than WO₃ and 2-propanol can be mineralized by the AgSbO₃ photocatalysis under visible light irradiation.     

Photocatalytic reduction of water by TaON under visible light irradiation

Some noble metals have been studied as H₂ evolution promoters for TaON, a visible light driven oxynitride photocatalyst. H₂ evolution on TaON photocatalyst under visible light irradiation (420 nm≤λ≤500 nm) in an aqueous methanol solution was found to be remarkably enhanced by adding Ru as a noble metal co-catalyst.     

Preparation of polyaniline-modified TiO2 nanoparticles and their photocatalytic activity under visible light illumination

Titanium dioxide nanoparticles were modified by polyaniline (PANI) using ‘in situ’ chemical oxidative polymerization method in hydrochloric acid solutions. Powder X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infrared spectra (FT-IR), X-ray photoelectron spectroscopy spectrum (XPS) and UV–vis spectra were carried out to characterize the composites with different PANI contents. The photocatalytic degradation of phenol was chosen as a model reaction to evaluate the photocatalytic activities of the modified catalysts. Results show that TiO₂ nanoparticles are deposited by PANI to mitigate TiO₂ particles agglomeration. The modification does not alter the crystalline structure of the TiO₂ nanoparticles according to the X-ray diffraction patterns. UV–vis spectra reveal that PANI-modified TiO₂ composites show stronger absorption than neat TiO₂ under the whole range of visible light. The resulting PANI-modified TiO₂ composites exhibit significantly higher photocatalytic activity than that of neat TiO₂ on degradation of phenol aqueous solution under visible light irradiation (λ ≥ 400 nm). An optimum of the synergetic effect is found for an initial molar ratio of aniline to TiO₂ equal to 1/100.     

Photocatalytic activation of TiO2 under visible light using Acid Red 44

The activation of TiO₂ photocatalyst for photocatalysis under the visible light using Acid Red 44 (C₁₀H₇N=NC₁₀H₃(SO₃Na)₂OH) is described. Adjustment of the pH enhanced the photocatalytic activation of TiO₂ in the presence of visible light. This confirms that the adsorption of a dye on TiO₂ surface is an important factor in dye-photosensitization. The differences in the photocatalytic activation mechanism under visible irradiated conditions with that of UV irradiated condition are proposed. The dye-sensitized photocatalysis under visible light was applied to the decomposition of phenol, is a toxic chemical used in industry and frequently discharged into water.     

Photocatalytic oxidation of cyanide under visible light by Pt doped AgInS2 nanoparticles

AgInS₂ nanoparticles were prepared by a microwave method, while Pt was doped on the surface of AgInS₂ via photoassisted deposition method. The catalytic performances of the AgInS₂ and Pt/AgInS₂ samples were carried out for photocatalytic oxidation of cyanide under visible light. The UV–vis analysis proved a red shift was detected after the loading of Pt into the AgInS₂. The maximum oxidation efficiency achieved was 100% at 1.5 wt% Pt/AgInS₂ photocatalyst after 35 min reaction time. The catalyst could be reused without any loss in activity during the first five cycles.     

Degradation of phenol in industrial wastewater over the F–Fe/TiO_2 photocatalysts under visible light illumination

F–Fe/TiO_2 composite photocatalyst was synthesized by a facile one-step hydrothermal method and then characterized by XRD, XPS and UV–Vis DRS. The catalyst of F–Fe/TiO_2 exhibited the highest photodegradation rate for phenol as compared with pure TiO_2, F/TiO_2, Fe/TiO_2, F0.38–Fe0.13–TiO_2 and Fe(III)/F-TiO_2 under visible light irradiation. The simulated conditions of industrial phenolic wastewater including initial phenol concentration,visible light intensity, p H and different anions were investigated in the presence of F–Fe/TiO_2 photocatalyst. In addition, as expected, the F–Fe/TiO_2 photocatalyst displayed excellent stability, showing a potential industrial application for the treatment of phenolic wastewater.     

Preparation of carbon-coated W18O49 and its photoactivity under visible light

Carbon-coated W₁₈O₄₉ powders were prepared from the mixture of para-ammonium tungstate with poly(vinyl alcohol) by heat treatment in inert atmosphere at a temperature between 750 and 900 °C for 1 h. The synthesized W₁₈O₄₉ crystals had prismatic morphology in small size, less than 0.5 μm in diameter and about 1 μm in length. Carbon-coated W₁₈O₄₉ was shown to have photoactivity under visible light irradiation by comparing the concentration changes of methylene blue, phenol and dimethylsulfoxide with time under the irradiation of visible light to that in the dark. Photoactivity of W₁₈O₄₉ was supposed to be due to the formation of OH radicals on the basis of the degradation of dimethylsulfoxide, its quantitative transformation to methanesulfonic acid. Carbon coating seemed to have various roles: to reduce WO₃ to W₁₈O₄₉, to inhibit the sintering and crystal growth of W₁₈O₄₉ to keep them small size, and also to concentrate pollutants around W₁₈O₄₉ crystal by adsorption.     

Sulfanilic acid-modified P25 TiO2 nanoparticles with improved photocatalytic degradation on Congo red under visible light

Visible-light-induced titania/sulfanilic acid nano-composite photocatalysts were prepared and characterized by FTIR, XPS, UV-vis, XRD, and SEM. The results indicate that the formation of Ti-O-S bonds after the modification of P25 TiO₂ nanoparticles with sulfanilic acid ligands extends the photoresponse of the photocatalyst from the UV to the visible range. The photocatalytic activity of the nano-composite photocatalyst was examined by degrading Congo red under visible light, in which its effecting factors such as irradiation time, catalyst dosage, solution pH and the addition of H₂O₂, were investigated in detail. The possible mechanism of photocatalytic degradation under visible irradiation has been also presented.     

Photocatalytic oxidation of methylene blue dye under visible light by Ni doped Ag2S nanoparticles

Ag₂S nanoparticles were prepared using a hydrothermal method, and Ni was doped via a photo-assisted deposition method. The samples produced were characterized using different tools. Furthermore, the catalytic performance of the Ag₂S and Ni/Ag₂S samples was examined in the degradation of methylene blue dye under visible light. The UV–vis spectral analysis detected a red shift after loading of Ni. The maximum degradation efficiency achieved was 100% with 3 wt% Ni/Ag₂S as the photocatalyst after a 40-min reaction time. The catalyst could be reused without any loss in activity for the first five cycles.     

Photocatalytic inactivation of bacteria by photocatalyst Bi2WO6 under visible light

The photocatalytic inactivation of Escherichia coli under visible light irradiation (λ > 420 nm) was performed with Bi₂WO₆ to investigate the photocatalytic bactericidal capability. Our work shows that the single phase oxide photocatalyst Bi₂WO₆ is effective in photocatalytic inactivation on E. coli. And the results revealed that the photocatalytic inactivation rate of E. coli with Bi₂WO₆ followed pseudo-first-order kinetics. The bactericidal action was directly observed by TEM and further proved by the measurement of K⁺ leakage from the inactive E. coli through the ICP-OES analysis. The results demonstrated that the photocatalysis could cause drastic damage in E. coli cells.     

Photocatalytic degradation of organic compounds diluted in water using visible light-responsive metal ion-implanted TiO2 catalysts: Fe ion-implanted TiO2

The application of metal ion-implantation method has been made to improve the electronic properties of the TiO₂ photocatalyst to realize the utilization of visible light. The photocatalytic properties of these unique TiO₂ photocatalysts for the purification of water have been investigated. By the metal ion-implantation method, metal ions (Fe⁺, Mn⁺, V⁺, etc.) are accelerated enough to have the high kinetic energy (150 keV) and can be implanted into the bulk of TiO₂. TiO₂ photocatalysts which can absorb visible light and work as a photocatalyst efficiently under visible light irradiation were successfully prepared using this advanced technique. The UV-Vis absorption spectra of these metal ion-implanted TiO₂ photocatalysts were found to shift toward visible light regions depending on the amount and the kind of metal ions implanted. They were found to exhibit an effective photocatalytic reactivity for the liquid-phase degradation of 2-propanol diluted in water at 295 K under visible light (λ>450 nm) irradiation. The investigation using XAFS analysis suggested that the substitution of Ti ions in TiO₂ lattice with implanted metal ions is important to modify TiO₂ to be able to adsorb visible light.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

TiO2 photoactivity in vis and UV light: The influence of calcination temperature and surface properties

A series of TiO₂ photocatalysts were obtained using several calcination temperatures ranging from 350 to 750 °C. The photocatalysts’ characteristics by X-ray diffraction, UV–vis and FTIR diffuse reflectance spectroscopies, X-ray photoelectron spectroscopy, BET and BJH methods showed that sample active in vis region had anatase structure, about 200 m²/g specific surface area, absorbed light for λ > 400 nm and contained 10.1 at.% of C–C species. The photocatalytic activity of the catalysts was estimated by measuring the decomposition rate of phenol in 0.21 mM aqueous solution in visible and ultraviolet light. The experimental data clearly indicate correlation between the absorption intensity of irradiation by obtained powders and their photocatalytic performance in phenol degradation. An increase in absorbance over the entire vis region and the highest photocatalytic activity for phenol degradation in visible light (λ > 400 nm) occurred for photocatalyst calcinated at 350 °C. Photocatalyst processed at 450 °C had the best activity in UV light (250 < λ < 400 nm).     

Photo-induced charging effect and electron transfer to the redox species on nitrogen-doped TiO2 under visible light irradiation

Energy levels for sub-band structures of the nitrogen-doped TiO₂ (N-TiO₂) and photo-excitation mechanism for the visible light response were investigated by photo-electrochemical and spectroscopic measurements. It was demonstrated that the photo-excitation from the N-doping level of N-TiO₂ causes the accumulation of electrons into the sub-band level at the potential energy of ca. +0.35 V vs. NHE (pH 2.5) under visible light irradiation. Subsequently, electron transfer does not take place from the photo-charged N-TiO₂ under visible light irradiation into such redox species as methyl viologen (MV²⁺), H⁺, Cu²⁺ ions, but into O₂ molecules, Pt⁴⁺, Ag⁺ and Au³⁺ ions by way of the sub-band level. These findings shed light on a mechanism for the photocatalytic reactions on the N-TiO₂ under visible light irradiation.     

C_3N_4-BiVO_4复合光催化剂可见光催化降解甲基橙

采用水热合成法制备C_3N_4-BiVO_4复合光催化剂,以甲基橙为目标污染物,研究催化剂用量、甲基橙溶液初始浓度和pH值、NaCl用量对甲基橙脱色率的影响,并通过C_3N_4-BiVO_4复合光催化剂的循环使用实验,考察其重复使用性能。结果表明,在甲基橙初始浓度20 mg·L~(-1)、复合光催化剂用量3.0 g·L~(-1)及弱酸性条件下,光照反应6 h,目标污染物甲基橙脱色率达98.81%,溶液中的NaCl对催化剂降解甲基橙有抑制作用。催化剂重复使用5次后,溶液脱色率约80%,表明催化剂性能较稳定,可重复使用。     

The Z-scheme heterojunction between TiO2 nanotubes and Cu2O nanoparticles mediated by Ag nanoparticles for enhanced photocatalytic stability and activity under visible light

The photocatalytic reduction method was used to introduce Ag nanoparticles (Ag NPs) into the Cu₂O-TiO₂ nanotubes (Cu₂O-TNT) prepared by electrodeposition. The Z-scheme heterojunction Cu₂O-Ag-TNT (CAT-4–60) catalysts were prepared. The mechanism of the transition from the traditional P-N heterojunction enhanced by noble metal to the Z-scheme heterojunction was studied. In addition, the Z-scheme heterojunction CAT-4–60 showed the highest light absorption and the highest photoelectrochemical activity under visible light, and the photoluminescence intensity was significantly reduced. Compared with the traditional P-N heterojunction CAT-2–60, not only the photocatalytic activity of the dual Z-scheme CAT-4–60 catalyst was improved, and the removal rate of MB was 98.58% higher than TNT (45.81%), CT-60 (69.49%), AT-2 (75.1%) and CAT-2–60 (91.2%),but also the stability of Cu₂O in CAT-4–60 was significantly enhanced. This work reveals the potential application of noble metal nanoparticles to enhance the Z-scheme heterojunction under visible light-driven photocatalysis, and provides new insights to the transition from traditional P-N heterojunctions to Z-scheme heterojunctions.     

Enhanced performance of g-C3N4/TiO2 photocatalysts for degradation of organic pollutants under visible light☆

Photocatalytic degradation is one of the most promising remediation technologies in terms of advanced oxida-tion processes (AOPs) for water treatment. In this study, novel graphitic carbon nitride/titanium dioxide (g-C3N4/TiO2) composites were synthesized by a facile sonication method. The physicochemical properties of the photocatalyst with different mass ratios of g-C3N4 to TiO2 were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), N2 sorption, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and UV–vis DRS. The photocatalytic performances were evaluated by degradation of methylene blue. It was found that g-C3N4/TiO2 with a mass ratio of 1.5:1 exhib-ited the best degradation performance. Under UV, the degradation rate of g-C3N4/TiO2 was 6.92 and 2.65 times higher than g-C3N4 and TiO2, respectively. While under visible light, the enhancement factors became 9.27 (to g-C3N4) and 7.03 (to TiO2). The improved photocatalytic activity was ascribed to the interfacial charge transfer between g-C3N4 and TiO2. This work suggests that hybridization can produce promising solar materials for envi-ronmental remediation.     

Enhanced visible light photocurrent generation at surface-modified TiO2 nanotubes

Photoelectrodes consisting of TiO₂ nanotube layers with different thicknesses (0.5 μm, 1.7 μm, 3 μm, 6 μm, 9 μm, and 18 μm) were prepared by anodization of titanium substrates and subsequent surface modification by a heat treatment at 400 °C in the presence of urea pyrolysis products. In contrast to unmodified TiO₂ nanotubes, the modified photoelectrodes exhibit photocurrents under visible light irradiation down to 750 nm. Photocurrent transients indicate enhanced recombination unless a suitable hole-scavenger, like iodide, is present since the photogenerated holes do not oxidize water efficiently. In the visible light the photoconversion efficiency increases significantly with nanotube length. The maximum incident photon-to-current efficiency (IPCE) was observed for tubes with the length of 6-9 μm (IPCE ∼4.5% and 1.4% at 450 nm and 550 nm, respectively) and the photocurrent enhancement with increasing tube length is found to be stronger at longer irradiations wavelengths.