Investigation of atomic vapour deposited TiN/HfO2/SiO2 gate stacks for MOSFET devices

HfO₂ films were grown by atomic vapour deposition (AVD) on SiO₂/Si (1 0 0) substrates. The positive shift of the flat band voltage of the HfO₂ based metal-oxide-silicon (MOS) devices indicates the presence of negative fixed charges with a density of 5 × 10¹² cm⁻². The interface trap charge density of HfO₂/SiO₂ stacks can be reduced to 3 × 10¹¹ eV⁻¹ cm⁻² near mid gap, by forming gas annealing. The extracted work function of 4.7 eV preferred the use of TiN as metal gate for PMOS transistors. TiN/HfO₂/SiO₂ gate stacks were integrated into gate-last-formed MOSFET structures. The extracted maximum effective mobility of HfO₂ based PMOS transistors is 56 cm²/Vs.     

A low gate leakage current and small equivalent oxide thickness MOSFET with Ti/HfO2 high-k gate dielectric

Annealing effects on electrical characteristics and reliability of MOS device with HfO₂ or Ti/HfO₂ high-k dielectric are studied in this work. For the sample with Ti/HfO₂ higher-k dielectric after a post-metallization annealing (PMA) at 600 °C, its equivalent oxide thickness value is 7.6 Å and the leakage density is about 4.5 × 10⁻² A/cm². As the PMA is above 700 °C, the electrical characteristics of MOS device would be severely degraded.     

Influence of the metal electrode on the characteristics of thermal Ta2O5 capacitors

The effect of various electrodes (Al, W, TiN) deposited by evaporation (Al) and sputtering (W, TiN) on the electrical characteristics of thermal thin film (15-35 nm) Ta₂O₅ capacitors has been investigated. The absolute level of leakage currents, breakdown fields, mechanism of conductivity, dielectric constant values are discussed in the terms of possible reactions between Ta₂O₅ and electrode material as well as electrode deposition process-induced defects acting as electrically active centers. The dielectric constant values are in the range 12-26 in dependence on both Ta₂O₅ thickness and gate material. The results show that during deposition of TiN and Al a reaction that worsens the properties of Ta₂O₅ occurs while there is not an indication for detectable reduction of Ta₂O₅ when top electrode is W, and the leakage current is 5-7 orders of magnitude lower as compared to Al and TiN-electroded capacitors. The high level of leakage current for TiN and Al gate capacitors are related to the radiation defects generated in Ta₂O₅ during sputtering of TiN, and damaged interface at the electrode due to a reaction between Al and Ta₂O₅, respectively. It is demonstrated that the quality of the top electrode affects the electrical characteristics of the capacitors and the sputtered W is found to be the best. The sputtered W gate provides Ta₂O₅ capacitors with a good quality: the current density <7 × 10⁻¹⁰ A/cm² at 1 V (0.7 MV/cm, 15 nm thick Ta₂O₅). W deposition is not accompanied by an introduction of a detectable damage leading to a change of the properties of the initial as-grown Ta₂O₅ as in the case of TiN electrode. Damage introduced during TiN sputtering is responsible for current deterioration (high leakage current) and poor breakdown characteristics. It is concluded that the sputtered W top electrode is a good candidate as a top electrode of storage capacitors in dynamic random access memories giving a stable contact with Ta₂O₅, but sputtering technique is less suitable (favorable) for deposition of TiN as a metal electrode due to the introduction of radiation defects causing both deterioration of leakage current and poor breakdown characteristics.     

Structural and electrical characteristics of RF-sputtered HfO2 high-k based MOS capacitors

The HfO₂ high-k thin films have been deposited on p-type (1 0 0) silicon wafer using RF magnetron sputtering technique. The XRD, AFM and Ellipsometric characterizations have been performed for crystal structure, surface morphology and thickness measurements respectively. The monoclinic structured, smooth surface HfO₂ thin films with 9.45 nm thickness have been used for Al/HfO₂/p-Si metal-oxide-semiconductor (MOS) structures fabrication. The fabricated Al/HfO2/Si structure have been used for extracting electrical properties viz dielectric constant, EOT, barrier height, doping concentration and interface trap density through capacitance voltage and current-voltage measurements. The dielectric constant, EOT, barrier height, effective charge carriers, interface trap density and leakage current density are determined are 22.47, 1.64 nm, 1.28 eV, 0.93 × 10¹⁰, 9.25 × 10¹¹ cm⁻² eV⁻¹ and 9.12 × 10⁻⁶ A/cm² respectively for annealed HfO₂ thin films.     

Improvement on low-temperature deposited HfO2 film and interfacial layer by high-pressure oxygen treatment

In this study, high-pressure oxygen (O₂ and O₂ + UV light) technologies were employed to effectively improve the properties of low-temperature-deposited metal oxide dielectric films and interfacial layer. In this work, 13 nm HfO₂ thin films were deposited by sputtering method at room temperature. Then, the oxygen treatments with a high-pressure of 1500 psi at 150 °C were performed to replace the conventional high temperature annealing. According to the XPS analyses, integration area of the absorption peaks of O-Hf and O-Hf-Si bonding energies apparently raise and the quantity of oxygen in deposited thin films also increases from XPS measurement. In addition, the leakage current density of standard HfO₂ film after O₂ and O₂ + UV light treatments can be improved from 3.12 × 10⁻⁶ A/cm² to 6.27 × 10⁻⁷ and 1.3 × 10⁻⁸ A/cm² at |Vg| = 3 V. The proposed low-temperature and high pressure O₂ or O₂ + UV light treatment for improving high-k dielectric films is applicable for the future flexible electronics.     

The effect of oxygen in Ru gate electrode on effective work function of Ru/HfO2 stack structure

Effective work function (φ_m,eff) values of Ru gate electrode on SiO₂ and HfO₂ MOS capacitors were carefully examined and discussed from the viewpoint of an effect of oxygen incorporation in Ru gate electrode on φ_m,eff. Annealing at 400 °C in the reduction (3%H₂) and the oxidation (1%O₂) ambient resulted in similar changes in the φ_m,eff of Ru/HfO₂/SiO₂ and Ru/SiO₂ MOS capacitors. Furthermore, the Ru gate MOS capacitor after annealing in the oxidation condition have shown almost the same φ_m,eff value to that of RuO₂ gate MOS capacitors. The oxygen concentration in the Ru/HfO₂ interface after annealing in oxidizing atmosphere is approximately one order of magnitude higher than that after annealing in reducing atmosphere as confirmed by secondary ion mass spectroscopy analysis. Furthermore, the higher oxygen concentration at the Ru/dielectric interface leads to the higher φ_m,eff value, regardless of SiO₂ or HfO₂ dielectrics. This indicates that φ_m,eff of Ru gate MOS capacitor is dominantly determined by the oxygen concentration at the Ru/dielectric layer interface rather than the dipoles originated from the oxygen vacancy in HfO₂.     

Impact of the TiN electrode deposition on the HfO2 band gap for advanced MOSFET gate stacks

The impact of the deposition of a TiN electrode on the high-k oxide HfO₂ has been investigated, focussing on the dielectric band gap. After the gate elaboration, a non-destructive approach combining Spectroscopic Ellipsometry (SE), Reflection Electron Energy Loss Spectroscopy (REELS) and X-ray Photoelectron Spectroscopy (XPS) was developed to probe the buried metal/high-k interface. The overall optical band gap is 5.9 ± 0.1 eV with no change after the metal gate deposition. A local reduction of 1 eV is measured near the TiN layer, due to N diffusion at the interface creating N 2p states at the top of the HfO₂ valence band. Increased disorder and defects are identified in the high-k after gate elaboration by XPS, REELS and SE.     

Damascene TiN-Gd2O3-gate stacks: Gentle fabrication and electrical properties

In this work, we present MOS capacitors and field effect transistors with a crystalline gadolinium oxide (Gd₂O₃) gate dielectric and metal gate electrode (titanium nitride) fabricated in a gentle damascene gate last process. Details of the gate last process and initial results on MOS devices with equivalent oxide thicknesses (EOT) of 3.0 nm and 1.5 nm, respectively, are shown.     

Characteristics of metal-ferroelectric-insulator-semiconductor structure using Sr0.8Bi2.2Ta2O9 and Sr0.8Bi2.2Ta2O9-BaZrO3 for ferroelectric gates

Characteristics of BaZrO₃ (BZO) modified Sr_0.8Bi_2.2Ta₂O₉ (SBT) thin films fabricated by sol-gel method on HfO₂ coated Si substrates have been investigated in a metal-ferroelectric-insulator-semiconductor (MFIS) structure for potential use in a ferroelectric field effect transistor (FeFET) type memory. MFIS structures consisting of pure SBT and doped with 5 and 7 mol% BZO exhibited memory windows of 0.81, 0.82 and 0.95 V with gate voltage sweeps between −5 and +5 V, respectively. Leakage current density levels of 10⁻⁸ A/cm² for BZO doped SBT gate materials were observed and attributed to the metallic Bi on the surface as well as intrinsic defects and a porous film microstructure. The higher than expected leakage current is attributed to electron trapping/de-trapping, which reduces the data retention time and memory window. Further process improvements are expected to enhance the electronic properties of doped SBT for FeFET.     

MOS devices with tetragonal ZrO2 as gate dielectric formed by annealing ZrO2/Ge/ZrO2 laminate

A Ge-stabilized tetragonal ZrO₂ (t-ZrO₂) film with permittivity (κ) of 36.2 was formed by depositing a ZrO₂/Ge/ZrO₂ laminate and a subsequent annealing at 600 °C, which is a more reliable approach to control the incorporated amount of Ge in ZrO₂. On Si substrates, with thin SiON as an interfacial layer, the SiON/t-ZrO₂ gate stack with equivalent oxide thickness (EOT) of 1.75 nm shows tiny amount of hysteresis and negligible frequency dispersion in capacitance-voltage (C-V) characteristics. By passivating leaky channels derived from grain boundaries with NH₃ plasma, good leakage current of 4.8 × 10⁻⁸ A/cm² at V_g = V_fb − 1 V is achieved and desirable reliability confirmed by positive bias temperature instability (PBTI) test is also obtained.     

Thermal annealing effect on electrical properties of metal nitride gate electrodes with hafnium oxide gate dielectrics in nano-metric MOS devices

Electrical properties of hafnium oxide (HfO₂) gate dielectric with various metal nitride gate electrodes, i.e., tantalum nitride (TaN), molybdenum nitride (MoN), and tungsten nitride (WN), were studied over a range of HfO₂ thicknesses, e.g., 2.5-10 nm, and post-metal annealing (PMA) temperatures, e.g., 600 °C to 800 °C. The work function of the nitride gate electrode was dependent on the material and the post-metal annealing (PMA) temperature. The scanning transmission electron microscopy technique is used to observe the effect of PMA on the interfacial gate dielectric thickness. After high-temperature annealing, the metal nitride gates were suitable for NMOS. At the same PMA temperature, the oxide-trapped charges increased and the interface state densities decreased with the increase of the HfO₂ thickness for TaN and WN gate electrodes. However, for MoN gate electrode the interface state density is almost independent of film thickness. Therefore, dielectric properties of the HfO₂ high-k film depend not only on the metal nitride gate electrode material but also the post-metal annealing condition as well as the film thickness. During constant voltage stress of the MOS capacitors, an increase in the time-dependent gate leakage current is also observed.     

Investigation of Ta2O5/SiO2/4H-SiC MIS capacitors

Tantalum pentoxide (Ta₂O₅) deposited by pulsed DC magnetron sputtering technique as the gate dielectric for 4H-SiC based metal-insulator-semiconductor (MIS) structure has been investigated. A rectifying current-voltage characteristic was observed, with the injection of current occurred when a positive DC bias was applied to the gate electrode with respect to the n type 4H-SiC substrate. This undesirable behavior is attributed to the relatively small band gap of Ta₂O₅ of around 4.3 eV, resulting in a small band offset between the 4H-SiC and Ta₂O₅. To overcome this problem, a thin thermal silicon oxide layer was introduced between Ta₂O₅ and 4H-SiC. This has substantially reduced the leakage current through the MIS structure. Further improvement was obtained by annealing the Ta₂O₅ at 900 °C in oxygen. The annealing has also reduced the effective charge in the dielectric film, as deduced from high frequency C-V measurements of the Ta₂O₅/SiO₂/4H-SiC capacitors.     

Physical and electrical characterization of polysilicon vs. TiN gate electrodes for HfO2 transistors

The effects of pre-deposition substrate treatments and gate electrode materials on the properties and performance of high-k gate dielectric transistors were investigated. The performance of O₃ vs. HF-last/NH₃ pre-deposition treatments followed by either polysilicon (poly-Si) or TiN gate electrodes was systematically studied in devices consisting of HfO₂ gate dielectric produced by atomic layer deposition (ALD). High-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) using X-ray spectra and Electron Energy Loss Spectra (EELS) were used to produce elemental profiles of nitrogen, oxygen, silicon, titanium, and hafnium to provide interfacial chemical information and to convey their changes in concentration across these high-k transistor gate-stacks of 1.0–1.8 nm equivalent oxide thickness (EOT). For the TiN electrode case, EELS spectra illustrate interfacial elemental overlap on a scale comparable to the HfO₂ microroughness. For the poly-Si electrode, an amorphous reaction region exists at the HfO₂/poly-Si interface. Using fast transient single pulse (SP) electrical measurements, electron trapping was found to be greater with poly-Si electrode devices, as compared to TiN. This may be rationalized as a result of a higher density of trap centers induced by the high-k/poly-Si material interactions and may be related to increased physical thickness of the dielectric film, as illustrated by HAADF-STEM images, and may also derive from the approximately 0.5 nm larger EOT associated with polysilicon electrodes on otherwise identical gate stacks.     

Charge trapping and interface characteristics in normally-off Al2O3/GaN-MOSFETs

Normally-off GaN-MOSFETs with Al₂O₃ gate dielectric have been fabricated and characterized. The Al₂O₃ layer is deposited by ALD and annealed under various temperatures. The saturation drain current of 330 mA/mm and the maximum transconductance of 32 mS/mm in the saturation region are not significantly modified after annealing. The subthreshold slope and the low-field mobility value are improved from 642 to 347 mV/dec and from 50 to 55 cm² V⁻¹ s⁻¹, respectively. The I_D-V_G curve shows hysteresis due to oxide trapped charge in the Al₂O₃ before annealing. The amount of hysteresis reduces with the increase of annealing temperature up to 750 °C. The Al₂O₃ layer starts to crystallize at a temperature of 850 °C and its insulating property deteriorates.     

Electrical properties of vacuum annealed La2O3 thin films grown by E-beam evaporation

In this article, the conduction mechanisms of metal-oxide-semiconductor with vacuum annealed Lanthana (La₂O₃) oxide film are investigated. Lanthana films with thicknesses of 3.5, 4.7, and 11 nm were deposited by E-beam evaporation on n-Si (100), and annealed at various temperatures (300-500 °C) in ultra-high vacuum (10⁻¹⁰-10⁻⁹ Torr) for 90 min. From the measurement of spectroscopic ellipsometry, it is found that film thickness is increased with annealing temperature, which would be cause of flat-band voltage shift (ΔV_FB) due to the growth of interfacial layer. From the capacitance measurement, it is found that ΔV_FB of the film is reduced by post-deposition anneal (PDA) compared to that of as-deposited film, but increase again at high temperature annealing, especially in the case of thin film (3.5 nm). From the applied voltage and temperature dependence of the leakage current of the film, with different gate electrode materials (Ag, Al, and Pt), it is shown that the leakage currents are associated with ohmic and Poole-Frenkel (P-F) conductions when flat-band voltage (V_FB) is less than zero, and ohmic and Space-Charge-Limited Current (SCLC) conductions when V_FB is greater than zero. The dielectric constants obtained from P-F conduction for Al gate electrode case is found to be 11.6, which is consistent with the C-V result 11.9. Barrier height of trap potential well is found to be 0.24 eV from P-F conduction. Based on SCLC theory, leakage currents of 3.5 and 11 nm films with different PDA temperatures are explained in terms of oxide trap density.     

Pentacene thin-film transistors with sol-gel derived amorphous Ba0.6Sr0.4TiO3 gate dielectric

An amorphous Ba_0.6Sr_0.4TiO₃ (BST) film with the thickness of 200 nm was deposited on indium-tin-oxide (ITO)-coated glass substrate through sol-gel route and post-annealing at 500 °C. The dielectric constant of the BST film was determined to be 20.6 at 100 kHz by measuring the Ag/BST/ITO parallel plate capacitor, and no dielectric tunability was observed with the bias voltage varying from −5 to 5 V. The BST film shows a dense and uniform microstructure as well as a smooth surface with the root-mean-square (RMS) roughness of about 1.4 nm. The leakage current density was found to be 3.5 × 10⁻⁸ A/cm² at an applied voltage of −5 V. The transmittance of the BST/ITO/glass structure is more than 70% in the visible region. Pentacene based transistor using the as-prepared BST film as gate insulator exhibits a low threshold voltage of −1.3 V, the saturation field-effect mobility of 0.68 cm²/Vs, and the current on/off ratio of 3.6 × 10⁵. The results indicate that the sol-gel derived BST film is a promising high-k gate dielectric for large-area transparent organic transistor arrays on glass substrate.     

Characterization of ultra-thin SiO2 by capacitance-voltage and charge pumping measurements

In this paper, we present results on electrical measurements of ultra thin SiO₂ layers (from 3.5 nm down to 1.7 nm), used as gate dielectric in metal-oxide-semiconductors (MOS) devices. Capacitance-voltage (C-V) measurements and simulations on MOS capacitors have been used for extracting the electrical oxide thickness. The SiO₂/Si interface and oxide quality have been analyzed by charge pumping (CP) measurements. The mean interface traps density is measured by 2-level CP, and the energy distribution within the semiconductor bandgap of these traps are investigated by 3-level charge pumping measurements. A comparison of the energy distribution of the SiO₂/Si interface traps is made using classical and quantum simulations to extract the surface potential as a function of the gate signal. When the gate oxide thickness <3.5 nm, we prove that it is mandatory to take into account the quantum effects to obtain a more accurate energy distribution of the SiO₂/Si interface traps. We also explain the increase of the apparent interface traps density measured by 2-levels CP with the increase of the oxide thickness, for transistors made from the same technological process.     

High-k HfO2-Ta2O5 mixed layers: Electrical characteristics and mechanisms of conductivity

Electrical properties of mixed HfO₂-Ta₂O₅ films (10;15 nm) deposited by rf sputtering on Si have been studied from the view point of their applications as high-k layers, by standard capacitance-voltage and temperature dependent current-voltage characteristics. The effect of HfO₂ addition to the Ta₂O₅ is thickness dependent and the thicker layers exhibit advantages over the pure Ta₂O₅ (higher dielectric constant, enhanced charge storage density and improved interface quality). The process of HfO₂ and Ta₂O₅ mixing introduces negative oxide charge, tends to creates shallow bulk traps and modifies the dominant conduction mechanisms in the stack capacitors as compared to the Ta₂O₅-based one (a contribution of tunneling processes through traps located below the conduction band of mixed layers to the leakage current in the HfO₂-Ta₂O₅ stacks is observed). The traps involved in both Poole-Frenkel and tunneling processes are identified.     

Fabrication and electrical characteristics of ultrathin (HfO2)x(SiO2)1−x films by surface sol-gel method and reaction-anneal treatment

Hafnium oxide (HfO₂) films were deposited on Si substrates with a pre-grown oxide layer using hafnium chloride (HfCl₄) source by surface sol-gel process, then ultrathin (HfO₂)_x(SiO₂)_1−x films were fabricated due to the reaction of SiO₂ layer with HfO₂ under the appropriate reaction-anneal treatment. The observation of high-resolution transmission electron microscopy indicates that the ultrathin films show amorphous nature. X-ray photoelectron spectroscopy analyses reveal that surface sol-gel derived ultrathin films are Hf-Si-O alloy instead of HfO₂ and pre-grown SiO₂ layer, and the composition was Hf_0.52Si_0.48O₂ under 500 °C reaction-anneal. The lowest equivalent oxide thickness (EOT) value of 0.9 nm of film annealed at 500 °C has been obtained with small flatband voltage of −0.31 V. The experimental results indicate that a simple and feasible solution route to fabricate (HfO₂)_x(SiO₂)_1−x composite films has been developed by means of combination of surface sol-gel and reaction-anneal treatment.     

Drain current enhancement and negligible current collapse in GaN MOSFETs with atomic-layer-deposited HfO2 as a gate dielectric

Accumulation-type GaN metal-oxide-semiconductor field-effect-transistors (MOSFET’s) with atomic-layer-deposited HfO₂ gate dielectrics have been fabricated; a 4 μm gate-length device with a gate dielectric of 14.8 nm in thickness (an equivalent SiO₂ thickness of 3.8 nm) gave a drain current of 230 mA/mm and a broad maximum transconductance of 31 mS/mm. Owing to a low interfacial density of states (D_it) at the HfO₂/GaN interface, more than two third of the drain currents come from accumulation, in contrast to those of Schottky-gate GaN devices. The device also showed negligible current collapse in a wide range of bias voltages, again due to the low D_it, which effectively passivate the surface states located in the gate-drain access region. Moreover, the device demonstrated a larger forward gate bias of +6 V with a much lower gate leakage current.