基于放热率分析的乙醇柴油燃烧特性的研究

对高速轻型车用柴油机燃用乙醇柴油燃料的放热率和燃烧特性进行了研究,并对多种比例乙醇柴油的排放特性进行了考察。研究表明:在乙醇柴油的十六烷值恢复到原柴油的条件下,乙醇柴油的预混燃烧延长,扩散燃烧缩短,总的燃烧持续期缩短;高负荷下的着火延迟接近柴油,但在中低负荷仍然与柴油有较大的差距;乙醇柴油的最大瞬时放热率低于柴油。在排放方面,乙醇柴油能够同时降低烟度和NOx排放,但在中低负荷下的CO和HC略有上升。     

柴油机燃用柴油醇的性能与排放特性的研究

研究了两种15％柴油醇在柴油机上的性能与排放特性。在ZS1100柴油机上，使用两种15％的柴油醇(加与不加十六烷值改进剂)，在保持发动机动力性不变的条件下，测试了发动机在主要工况下的油耗、排气温度、烟度和一氧化碳(CO)、氮氧化物(NOx)、总碳氢(THC)等有害气体排放物，且与原机进行了比较。分析结果发现：在柴油中加入一定比例的乙醇，发动机的比油耗增加，但有效热效率可以提高1％～2％；发动机的烟度在各种工况下都能够显著降低；CO在低负荷下增加，在高负荷下减少；而NOx在低负荷下降低，却在大负荷下增加；THC在各种工况下都增加。在柴油醇中加入十六烷值改进剂后，发动机的经济性和热效率没有明显变化，但是CO和NOx在各种工况下都低于不加十六烷值的混合燃料，THC却进一步升高。     

着火改进剂对乙醇--柴油燃料排放特性的影响

随着乙醇含量的增加，乙醇柴油混合燃料的含氧量增大，但热值、十六烷值和粘度下降。助溶剂可以提高混合燃料的稳定性，着火改进剂能提高它的十六烷值。在发动机上的研究结果表明：柴油机的排放与负荷、掺醇量、助溶剂及着火改进剂有关。大负荷时，随着混合燃料中乙醇含量的增加，烟度明显改善，NOx排放有所降低，但使用乙醇柴油混合燃料时，未燃乙醇和乙醛排放增加，而且CO和总碳氢(THC)排放高于柴油，但助溶剂与着火改进剂能降低CO和THC排放，THC排放甚至低于柴油。     

柴油机TR燃烧系统实现低温预混合燃烧的研究

为了验证TR燃烧系统降低发动机排放、实现低温预混合燃烧的能力,在一台经过改造的单缸135柴油机上进行了降低压缩比、燃用柴油-乙醇混合燃料和推迟供油的试验研究.结果表明,压缩比ε降低后,着火推迟,最大放热率增加,缸内最高压力和最高温度降低,NOx排放也降低.但是中高负荷时燃烧速率降低,有效油耗率增加.当燃用乙醇体积含量20%的乙醇-柴油混合燃料时,与燃用柴油燃料相比,着火延迟期延长,烟度大幅度降低.小负荷时缸内最高压力、最高温度、最大放热率和燃烧速率都降低,NOx降低较多;中高负荷时最大放热率高于后者,燃烧速率提高,NOx降低得较少.当供油定时从15°CA BT-DC推迟到13°CA BTDC后,烟度基本不变.     

不同海拔下VGT对含氧燃料柴油机性能的影响

利用大气压力模拟装置,试验研究了可变几何截面涡轮增压器(VGT)对高压共轨柴油机分别燃用纯柴油和生物柴油-乙醇-柴油(BED)含氧燃料的经济性、排放特性及燃烧特性的影响。结果表明:随着海拔的升高,柴油机经济性恶化,氮氧化物(NO_x)排放降低,而一氧化碳(CO)和碳氢化合物(HC)排放及烟度升高。燃用纯柴油与含氧燃料,随着VGT喷嘴环开度的增大,柴油机的经济性均有不同程度的恶化,而CO、HC排放及排气烟度也都有不同程度的升高。在高海拔地区,燃用纯柴油的经济性优于含氧燃料,但使用含氧燃料有助于改善柴油机的CO、HC排放及烟度。在中等负荷工况下,NO_x排放随着VGT喷嘴环开度的增大呈现先减小后增大的趋势;在高负荷工况下,放热率峰值和最高气缸压力均随着VGT喷嘴环开度的增大而降低,从而降低了NO_x排放。     

燃料设计策略对低温燃烧负荷拓展和热效率改善北大核心CSCD

在一台高压共轨直喷式柴油机上进行了低温燃烧的研究,并采用燃料设计的理念研究了不同燃料特性对低温燃烧的负荷范围和热效率的影响规律。研究表明:生物柴油为含氧燃料可降低局部当量比,促进和改善缸内燃烧过程,烟度大幅下降,从而拓展了低温燃烧负荷范围。乙醇柴油混合燃料具有较低的十六烷值和较高的含氧量,雾化效果较好,这些特性都有利于降低烟度,拓展低温燃烧的负荷范围。由于低十六烷值燃料较长的滞燃期,允许采用较早的喷射时刻,从而提高了低温燃烧的热效率,尤其是含20%乙醇的混合燃料。低十六烷值含氧燃料(乙醇柴油)在低温燃烧方面具有较大的潜力。     

柴油机燃用生物柴油-乙醇-水微乳化燃料性能研究

为研究生物柴油-乙醇-水微乳化燃料在柴油机上的应用,在单缸直喷式柴油机上,对生物柴油和生物柴油-乙醇-水微乳化燃料的燃烧特性、经济性和排放进行试验研究。研究结果表明:与生物柴油相比,生物柴油-乙醇-水微乳化燃料的压力、压力升高率及放热率曲线明显后移;峰值燃烧压力和峰值瞬时燃烧放热率增加,燃烧更加完全、放热更加集中;瞬时燃烧放热率第二峰值明显降低,瞬时燃烧放热率曲线型心转角在中高负荷更加靠近上止点,循环等容度和有效效率明显提高;燃料消耗率增加而比能耗略有降低;NOx和烟度排放明显降低。研究结果表明:生物柴油-乙醇-水微乳化燃料是节能、环保的柴油机代用燃料。     

一种新型含氧燃料燃烧与排放性能研究

开展了柴油机燃用柴油／乙二醇单丁醚混合燃料的燃烧与排放性能研究。试验结果表明：在柴油机中加入一定比例的乙二醇单丁醚（NBE）,柴油机热效率得到明显提高,着火略有延迟,燃烧速度加快,燃烧持续期缩短。烟度和CO排放大幅度降低。加入159／5～25％NBE时,烟度下降43．9％～759／5,CO排放在高负荷下降46．5％～56％,HC排放也不同程度降低,NOx排放稍有下降。试验结果显示了柴油机燃用乙二醇单丁醚在降低排放方面的优越性。     

自然吸气直喷压燃式发动机燃用柴油醇的性能和排放

应用助溶剂解决了乙醇和柴油相溶性较差的问题并配制柴油醇燃料,分析了柴油醇的主要理化特性,结果表明,柴油醇的黏度、热值和十六烷值有所下降,但汽化潜热却明显增加。自然吸气直喷压燃式发动机不作任何调整,燃用E10柴油醇,动力性和经济性基本不变,燃用E20柴油醇,动力性下降,小负荷经济性恶化。燃用柴油醇,在中小负荷工况,CO和HC浓度排放增加,NOx浓度排放减少;在大负荷工况,CO浓度排放减少,HC浓度排放变化较小,NOx浓度排放增加,排气烟度降低明显。柴油醇中乙醇含量越多,排放性能变化越大。适当推迟供油提前角对压燃式发动机燃用柴油醇的性能有利。     

柴油机燃用不同比例菜籽油生物柴油和乙醇柴油的对比试验研究

在一台S195直喷柴油机上进行燃料燃烧对比试验,试验结果表明,燃用生物柴油和乙醇柴油会使柴油机的动力性有所下降,其中菜籽油生物柴油的动力性接近纯柴油燃料的动力性,乙醇柴油的动力性相对较差。生物柴油和乙醇柴油的油耗率都比纯柴油要高,生物柴油的油耗率要高于乙醇柴油。但随负荷的增大,这种差距呈下降趋势。生物柴油和乙醇柴油在较大工况范围都可以保持比纯柴油燃料较低的CO排放量。低负荷状态下改善不明显,甚至会增大;高负荷工况下,混合燃料的CO排放比纯柴油降低较多。绝大部分工况下,生物柴油和乙醇柴油燃料的HC排放都比纯柴油高。绝大部分工况下,生物柴油和乙醇柴油的NOx排放和碳烟排放都比纯柴油低,其中生物柴油的表现优于乙醇柴油。     

小型锅炉烟尘测试时锅炉出力的计算

锅炉烟尘测试时,必须对锅炉出力进行测试。但监测中,许多小型锅炉往往不具备相关的计量装置和仪表,为解决这一问题,文章提出了用烟气量和空气过剩系数来计算锅炉的出力的公式,在实际使用中,该方法简单易行,其结果和实测值具有很好的一致怀。     

Unerroric of control of mutual compliance of the efficiency of hydrogen engines of unmanned vehicles in the conditions of mass production

The issues related to the reliability of hydrogen engines of unmanned vehicles and increasing the efficiency of using hydrogen as fuel when using the method of its production during the decomposition of hydrogen-containing molecules of liquid-phase organic compounds in a plasma discharge under the action of intense ultrasonic exposure are considered. Experiments have shown that as a result of decomposition in the acoustoplasma discharge of liquid hydrocarbons, solid-phase carbon-containing products are formed, chemical transformations occur in the liquid phase and hydrogen-containing combustible gas is formed. Hydrogen-containing gas can be used as fuel immediately after synthesis, i.e. it does not require separation, since in addition to hydrogen it contains only impurities of CO₂ and water vapor. The purpose of the study is to formalize the basic conditions for tightening the control of mutual compliance with the efficiency of hydrogen engines of the same series in the conditions of their mass production. Methods of mathematical statistics and hardware-software modeling were used in the study. The term “unerroric of quality mutual compliance control” is introduced to describe a set of hardware and software tools for such control. The principle of in-depth testing of the technical condition of such engines of one series is described in a multidimensional formulation of the quality control problem for three of their operating parameters at once. The conditions for increasing the mutual correspondence of the measured values of such parameters in the conditions of serial production of hydrogen engines are formalized.     

中国煤炭地下气化技术的发展

本文综述了煤炭地下汽化技术的国内外发展现状,对我国“长通道、大断面”煤炭地下气化新工艺给予了技术经济评述,并提出了发展煤炭地下汽化技术的政策建议。     

Review of theory of distortion and disintegration of liquid streams

Linear and nonlinear analyses of the instabilities and distortion of liquid streams injected into a gaseous media are discussed. The various fundamental mechanisms and the predictive capabilities for the distortions are emphasized. Round jets, planar sheets, annular sheets, and conical sheets are discussed in detail. The balance between capillary and inertial forces is primarily examined. The method for simplifying the analyses in the case of thin liquid sheets is discussed. The capabilities for representing the droplet size distribution that follows the stream disintegration are outlined.     

MgO膨胀剂细度对MgO水化和水泥浆体膨胀的影响

基于《水工混凝土掺用氧化镁技术规范》中的Ⅰ型氧化镁（MgO）,研究了该型MgO膨胀剂（MEA）细度对掺粉煤灰水泥浆体膨胀性能的影响。即采用X射线衍射分析(XRD)及同步热分析（TG DSC）分析了掺MEA水泥浆体中MgO的水化性。结果表明,养护温度相同时,MEA的细度对水泥浆体内MEA中MgO的水化和水泥浆体的膨胀无显著影响,产生的膨胀均能补偿水泥浆体的收缩;MEA的细度可从试验设计采用的45 μm筛筛余15%左右增加到30%左右,这将有利于MEA生产企业的节能降耗。     

机车车轮多轴疲劳强度安全评定的研究

使用ANSYS8.0软件对高速列车车轮进行了三维有限元分析,计算出车轮在直线、曲线和道岔条件下牵引、制动共6种工况时孔边薄弱部位的应力,分别通过Mises等效平均应力方法、Sines平均主应力方法和应力分量中考虑平均应力方法计算出应力在极值位置时的等效应力幅、等效平均应力,从而进一步算出车轮的安全系数,对其疲劳强度进行评定,并对3种方法进行了比较研究。     

Constructal optimization of the geometry of an array of micro-channels

This paper documents the geometric optimization of an array of circular and non-circular ducts. The optimization was carried out numerically using finite volume method. As optimal dimensions were independent of the array configuration, the numerical simulation was performed on a unit cell. Numerical optimization for circular, square and isosceles right triangle cross-sections of channels was performed. Based on the results of this investigation, some correlations were proposed to predict the optimal hydraulic diameter and dimensionless heat transfer per unit volume. In addition to examining the effect of pressure drop on these parameters, it was showed that among the different geometries of this study, square cross-section has the most efficiency for a given volume. The numerical results of the present study were compared with approximate results reported in the literature which a good agreement was observed.     

固体热辐射Yong性能分析

本文对漫灰均温物体在常物性条件下对外辐射传热的Ｙｏｎｇ值计算建立了数学模型。通过与物体内能Ｙｏｎｇ公式的数值计算比较,得出了辐射能量的Ｙｏｎｇ值不大于内能Ｙｏｎｇ值的结论。从初步的热射Ｙｏｎｇ值计算公式发现。Ｙｏｎｇ与物体表面辐射率有关。     

Measurements of concentration distribution of hydrogen jet using deflection of center of the laser spot

The main purpose of this work is to propose a new method to evaluate the concentration distribution of the hydrogen jet by using a He–Ne laser through the jet. This research attempts to apply the expression of concentration Gaussian distribution, the refraction formula of inhomogeneous refractive index medium, and the concentration inversion function to disclose the displacement of the center of the laser spot at different heights in the gas jet. The spot images of the laser beam passing through the gas jet at three vertical heights z = 10d, 20d, 30d, and different radial positions are obtained. The radial spatial asymmetry of the gas jet is also found in the experiment. Finally, the calculated concentration distribution curve and the fluent simulation curve, it is found that the two results are very similar. Our findings show that the error between the concentration distribution of this method and the simulated concentration distribution reaches 2.43%.     

Heat of vaporization of mixtures

General expressions for the heat of vaporization of mixtures at constant pressure; at constant temperature; and at constant pressure, temperature, and composition are proposed. The last one is related to the liquid-vapor interface where steady vaporization or condensation is taking place. Numerical examples by the proposed expressions are shown for binary mixtures of HCFC22(R22) and (HCFC123(R123) © 1997 Scripta Technica, Inc. Heat Trans Jpn Res, 25(1): 12–24, 1996