Simulation of the hydrodynamics and mass transfer in a falling film wavy microchannel

The flow in a liquid falling film is predominantly laminar, and the liquid-side mass transfer is limited by molecular diffusion. The effective way to enhance the mass transfer is to improve the liquid film flow behavior. The falling film behaviors of water, ethanol and ethylene glycol in nine different wavy microchannels were simulated by Computational Fluid Dynamics. The simulation results show that the falling film thickness exhibits a waveform distribution resulting in a resonance phenomenon along the wavy microchannel. The fluctuation of liquid film surface increases the gas–liquid interface area, and the internal eddy flow inside the liquid film also improves the turbulence of liquid film, the gas–liquid mass transfer in falling film microchannels is intensified. Compared with flat microchannel, the CO_2 absorption efficiency in water in the wavy microchannel is improved over 41%. Prediction models of liquid film amplitude and average liquid film thickness were established respectively.     

Mass transfer area in a multi-stage high-speed disperser with split packing

In this study, the mean droplet diameter in the cavity zone and the total mass transfer area of a multi-stage highspeed disperser(HSD) reactor with different packing combinations were measured and evaluated. The effects of rotational speed and packing radius, as well as the packing ring radius and numbers, on the mean droplet diameter and the total mass transfer area were evaluated. A model was established to calculate the mass transfer area in the cavity zone in the HSD reactor, and it was found that the packings contribute 61%–82% of the total mass transfer area. A correlation for predicting the mass transfer area in the packing zone was regressed by the dimensionless analysis method. An enhancement factor based on the mass transfer area in the packing zone was proposed to evaluate the effect of packing combination on mass transfer area. Two optimum packing combinations were proposed in consideration of the mean droplet diameter and the enhancement factor.     

IMPROVED HYDRODYNAMIC MODEL OF TWO-PHASE SLUG FLOW IN VERTICAL TUBES

Merits of the Fernandes model(Fernandes et al.1983)for two-phase slug flow in verticaltubes are reviewed in this paper.While predicting many macroscopic parameters of slug flow in verti-cal tubes,it fails to present correctly the trend that the average voidage in liquid slugs increases asthe rising velocity of Taylor bubbles is increased.It is also desirable to extend its application toelectrolyte systems, and to churn flow conditions.Based on the diagnostic analysis,the model equa-tion for gas entrainment by falling liquid film is reformulated and the influence of surface tension isalso accounted for.Development of the falling liquid film is recognized in the revised model in or-der to suit the case of short Taylor bubbles as well.The modified model predicts the variation of av-erage voidage in liquid slugs in good agreement with available experimental data.     

竖直流动皂膜中解吸导致的Marangoni对流观察

In gas-liquid mass transfer processes,Marangoni convection may occur due to the surface tension gradient produced by mass transfer near the interface.With a falling soap film tunnel and the Schlieren optical method,the Marangoni convection patterns along the film surface were observed directly in the desorption process of acetone from the falling soap film.The Schlieren images showed the regular roll convection in the thin falling soap film during the acetone desorption.The hydraulic characteristics were determined experimentally by measuring the variation of acetone concentration in the film and the surface tension of the soap liquid.The results show that the acetone concentration gradient vertical to the falling direction is very small because the thickness of the soap film is in the order of 10^-6 m.The variation of acetone concentration along the falling film is large,so there is a significant surface tension gradient,resulting in the Marangoni roll convection.The experimental results and a qualitative analysis may be helpful to understand the mechanism of Marangoni convection near the interface in the mass transfer.     

垂直管内气液两相弹状流含气率研究

In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical probes and an EKTAPRO 1000 high speed motion analyzer. It demonstrates that the radial profile of slug flow void fraction is parabolic. Influenced by the falling liquid film, the radial profile curve of liquid slug void fraction in the wake region is also parabolic. Since fully turbulent velocity distribution is built up in the developed region,the void fraction profile in this region is the saddle type. At given superficial liquid velocity, the liquid slug void fraction increases with gas velocity. The radial profiles of liquid slug void fraction at different axial locations are all saddle curves, but void fraction is obviously high around the centerline in the entrance region. The nearer the measuring station is from the entrance, the farther the peak location is away from the wall.     

一串上升气泡周围流体的湍动特性(英文)

The turbulence behavior of gas-liquid two-phase flow plays an important role in heat transfer and mass transfer in many chemical processes. In this work, a 2D particle image velocimetry (PIV) was used to investigate the turbulent characteristic of fluid induced by a chain of bubbles rising in Newtonian and non-Newtonian fluids. The instantaneous flow field, turbulent kinetic energy (TKE) and TKE dissipation rate were measured. The results demonstrated that the TKE profiles were almost symmetrical along the column center and showed higher values in the central region of the column. The TKE was enhanced with the increase of gas flow and decrease of liquid viscosity. The maximum TKE dissipation rate appeared on both sides of the bubble chain, and increased with the increase of gas flow rate or liquid viscosity. These results provide an understanding for gas-liquid mass transfer in non-Newtonian fluids.     

MASS TRANSFER IN DRIPPING PLATE COLUMN FOR NON-NEWTONIAN FLUIDS

In this paper, the mass transfer for non-Newtonian liquid has been studied in a dripping plate column fitted with perforated trays. The rate of evaporation of polymer solution in the column was measured and correlated. It was found that temperature, presure, mass flow rate and the non-Newtonian behavior of the solution are the significant factors having effects on mass transfer.     

考虑界面蒸发时的降液膜流动传热

The interfacial evaporative heat transfer was included in the semi-empirical study of the heat transfer for the falling liquid film flow. The investigations showed that, the inclusion of the interfacial evaporative heat transfer in the turbulent model would lower the predicted convective heat transfer coefficient. Predictions of the new model resulted in a prominent deviation from that predictions of the normal model in the case of large mass flow rate and low wall heat flux. This deviation will be decreased with increasing wall heat flux, such that it will be asymptotic zero at very high wall heat flux. Predictions of the new model agreed well with the current experimental measurements. This study has verified that the Reynolds number is not the sole crucial parameter for heat transferof falling liquid film flow, and wall heat flux will be another important independent parameter. This result is consistent with our previous studies.     

Prediction of mass transfer coefficients in an asymmetric rotating disk contactor using effective diffusivity

Mass transfer characteristics have been investigated in a 113 mm diameter asymmetric rotating disk contactor of the pilot plant scale for two different liquid–liquid systems. The effects of operating parameters including rotor speed and continuous and dispersed phase velocities on the volumetric overall mass transfer coefficients are investigated. The results show that the mass transfer performance is strongly dependent on agitation rate and interfacial tension, but only slightly dependent on phase flow rates. In this study, effective diffusivity is used instead of molecular diffusivity in the Gr?ber equation for estimation of dispersed phase overall mass transfer coefficient.The enhancement factor is determined experimentally and there from an empirical expression is derived for prediction of the enhancement factor as a function of Reynolds number. The predicted results compared to the experimental data show that the proposed correlation can efficiently predict the overall mass transfer coefficients in asymmetric rotating disk contactors.     

Microinterface intensification in hydrogenation and air oxidation processes

Hydrogenations and air oxidations usually have low apparent reaction rate,generally controlled by mass transfer rate,and widely exist in the modern chemical manufacturing process.The key to increase the mass transfer rate is the reduction of the liquid film resistance 1/k_La.In this work,the original concept of microinterface intensification for mass transfer and then for these reactions has been proposed.We derived the regulation model and set up the mathematical calculation method of...     

垂直管内弹状气泡上升中壁面传递的实验研究

垂直管内弹状流壁面传递是诸多工业应用中需研究的重要问题之一。今用极限扩散电流技术,对弹状气泡上升时瞬时壁面剪应力和传质系数进行了测定,结果显示:当基于表观气速的Froude数FrG < 0.74时,壁面剪应力随弹状气泡和液塞的到来呈现方向相反的交替变化,壁面传质系数亦相应变化;而当FrG > 0.74时,剪应力方向一直向下,说明液膜向下流动,且弹状气泡和液塞的到来对壁面传质系数的影响很小。这说明下落液膜射流穿透了液塞段,控制了整个壁面传递过程。研究还对下落液膜区、尾迹区及液塞段的不同传递特征及机理进行了分析, 并结合气泡塔熔融结晶器中弹状气泡上升时的传热,对结晶操作条件的合理选择进行了讨论。     

Hydrodynamics and local mass transfer characterization under gas–liquid–liquid slug flow in a rectangular microchannel

Gas–liquid–liquid three-phase slug flow was generated in a glass microreactor with rectangular microchannel, where aqueous slugs were distinguished by relative positions to air bubbles and organic droplets. Oxygen from bubbles reacted with resazurin in slugs, leading to prominent color changes, which was used to quantify mass transfer performance. The development of slug length indicated a film flow through the corner between bubbles and the channel wall, where the aqueous phase was saturated with oxygen transferred from bubble body. This film flow results in the highest equivalent oxygen concentration within the slug led by a bubble and followed by a droplet. The three-phase slug flow subregime with alternate bubble and droplet was found to benefit the overall mass transfer performance most. These results provide insights into a precise manipulation of gas–liquid–liquid slug flow in microreactors and the relevant mass transfer behavior thereof.     

Hydrodynamic studies of liquid–liquid slug flows in circular microchannels

The aim of the work presented was to clarify the existence of a wall film and its influence on the hydrodynamics of liquid–liquid slug flow capillary microreactor.The methodology of the laser induced fluorescence (LIF) was adopted for visualisation purposes. The measurement of the light intensity profiles revealed a fully developed wall film for a variety of aqueous–organic two-phase systems in glass and PTFE capillaries of 1 mm internal diameter. In addition an acid as a quenching agent enabled the observation of the internal circulation patterns within the liquid slugs, as the fluorescent dye was deactivated by the acid diffusing in from the dye-free phase. A well-defined internal circulation pattern was always present in the wetting phase, i.e. that forming the wall film, leading to uniform mixing in the slugs of this phase. Stagnant zones and local circulation vortices, indicated by variations in the concentrations of the quenched dye, were observed in the non-wetting dispersed phase. These more complex flow structures varied little with the slug velocity, but were strongly dependent on the physical properties of the liquid–liquid system. To predict slug shape and hydrodynamics within the liquid slugs, CFD simulations were carried out using the volume-of-fluid method (VOF) based on the incompressible Navier–Stokes equation with appropriate boundary conditions between the two phases. The slug generation process was studied in a T-junction with 1 mm internal diameter inlets. The implementation of the wetting contact angle, measured in the visualisation experiments for the various systems, led to realistic slug lengths and shapes. The velocity vector plot indicated a fully developed internal circulation pattern within the simulated slugs. Calculations for a single slug with a non-wetting condition gave rise to a wall film in the simulated system.The results obtained demonstrate the significance of the wall film in the hydrodynamics and mass transfer liquid–liquid slug flow and reveal the presence of hitherto unsuspected complex patterns in place of simple single Taylor vortex flow assumed in the past.     

微通道内气-液弹状流动及传质特性研究进展

气-液弹状流,又称Taylor流,是一种以长气泡和液弹交替形式流动的流动形态。微通道内气-液弹状流因其气泡与液弹尺寸分布均一、停留时间分布窄、径向混合强等优点,是一种适于强化气-液反应的理想流型。本文首先介绍了微通道内气泡的生成机理、气泡和液弹长度,以及气泡生成阶段的传质特征。其次系统综述了主通道中弹状流动及传质过程的研究进展,包括气泡形状与液膜厚度、液弹内循环和泄漏流特征、气-液传质系数的测量与预测,以及物理与化学吸收过程中的传质特性等方面内容。最后阐述了当前研究的不足并展望了气-液弹状流的研究方向。     

毛细管中泰勒流液侧传质特性及其强化机理的CFD模拟

采用计算流体力学（CFD）的方法,研究了圆管中泰勒流的液侧传质特性,分析了泰勒气泡上局部传质特性,并研究了气泡上升速度、液膜长度和液栓长度对液膜处和气泡半球帽处平均传质系数的影响。结果表明,泰勒气泡表面局部传质系数存在3个峰值,液膜处的平均传质系数随气泡上升速度增大显著增大,随液膜长度增大而减小,而半球帽处的平均传质系数随气泡速度和液膜长度的增大变化较小,即膜接触时间增加时,液膜处的传质系数降低,而半球帽处传质系数变化较小。另外,引入场协同原则对单元胞内速度场和浓度场进行分析,解释了局部传质特性及强化机理。最后,给出了分别预测短和长膜接触时间下泰勒流液侧体积传质系数的关联式,该式在较宽的管径尺度范围（0.25～3 mm）内的预测误差在±20%以内。     

Arduino-based slider setup for gas–liquid mass transfer investigations: Experiments and CFD simulations

The implementation of traditional sensors is a drawback when investigating mass transfer phenomena within microstructured devices, since they disturb the flow and reactor characteristics. An Arduino based slider setup is developed, which is equipped with a computer-vision system to track gas–liquid slug flow. This setup is combined with an optical analytical method allowing to compare experimental results against CFD simulations and investigate the entire lifetime of a single liquid slug with high spatial and temporal resolution. Volumetric mass transfer coefficients are measured and compared with data from literature and the mass transfer contribution of the liquid film is discussed.     

Predicting inter-phase mass transfer for idealized Taylor flow: A comparison of numerical frameworks

Four numerical frameworks were derived to investigate the impact of underlying assumptions and numerical complexity on the predicted mass transfer between a Taylor bubble and liquid slug in circular capillaries. The separate influences of bubble velocity and film length, slug length, and bubble film thickness on k_La were compared to empirical and CFD-based predictions from existing literature. Reasonable agreement was obtained using a Slug Film model, which accounted for diffusion-limited mass transfer between the slug film and circulating bulk without the need for an iterative numerical solution. Subsequent investigation of the relative contributions of film and cap mass transport for industrially relevant conditions suggests that both mechanisms need to be accounted for during the prediction of k_La.     

Design and operation of gas–liquid slug flow in miniaturized channels for rapid mass transfer

The influences of operating parameters such as channel size, flow rate, and void fraction on the mass transfer rate in the gas–liquid slug flow are investigated to establish a design method to determine the parameters for rapid mass transfer. From the experimental results, the turnover index, including the slug linear velocity, its length, and the channel size that represents the turnover frequency of the internal circulation flow, is proposed. For PTFE tube in which no liquid film exists in slug flow, a master curve is derived from the relationship between the mass transfer coefficient and the turnover index. For each channel material, the Sherwood number is also roughly correlated with the Peclet number. These correlations make it possible to arbitrarily determine a set of operating parameters to achieve the desired mass transfer rate. However, the turnover index and the Peclet number include the slug length, which cannot be controlled directly. The relationship between the slug length and the operating parameters is also investigated. The slug volume mainly depends on the inner diameter (i.d.) of a union tee. At a fixed union tee i.d., the slug length is controlled through the exit i.d. of the channel connected to the union tee and the void fraction. Thus, the final slug length depends on the union tee and exit channel inner diameters. At low flow rates, the gas and liquid collision angle is significant in determining the slug length.     

Aerobic oxidation of benzyl alcohol in a slug flow microreactor: Influence of liquid film wetting on mass transfer

Homogeneous Co/Mn/Br catalyzed aerobic oxidation of benzyl alcohol in acetic acid to benzaldehyde was performed in polytetrafluoroethylene microreactors operated under slug flow at temperatures up to 150°C and pressures up to 5 bar. Depending on the bubble velocity and length, a wetted or dewetted slug flow was observed, characterized typically by a complete or partially wetting liquid film around the bubble body. The latter flow suffered from a limited interfacial area for mass transfer. Experiments at temperatures up to ca. 90°C were under kinetic control given no product yield difference under wetted and dewetted slug flows and were used to establish a simplified kinetic expression (first order in benzyl alcohol and zero order in oxygen). This allows to develop a mass transfer model combined with an instantaneous reaction regime that well described the experimental results at higher temperatures where mass transfer was limiting in the dewetted slug flow.     

Experiment and calculation of filtration processes in an external-loop airlift ceramic membrane bioreactor

Air sparging is recognized as an effective way to increase permeate flux in membrane filtration processes. The application of air sparging with an external-loop airlift ceramic membrane bioreactor was studied at different gas flow rates, biomass concentrations and suction pressures. A 180% increase in permeate flux was obtained while filtering a 2 g/L activated sludge wastewater suspension with the airlift cross-flow operation for U_g=0.21 m/s. The mechanism of flux enhancement in the case of slug flow in tubular membrane was discussed. The region near the gas slug was divided into three different zones: falling film zone, wake zone and remaining liquid slug zone. Air sparging significantly lowered cake thickness and consequently cake resistances for the wake region and the falling film region. A novel model combining hydrodynamic of gas-liquid two-phase flow and cake resistance was developed to simulate the process. The model was validated with experimental data with an error of 8.3%.