Nb2O5-supported WO3: a comparative study with WO3/Al2O3

WO₃/Nb₂O₅-supported samples prepared by impregnation are characterised by X-ray diffraction (XRD), Raman spectroscopy and X-ray absorption spectroscopy (XAS) at the W–L₃ absorption edge, as well as temperature programmed reduction (TPR) and FT-IR monitoring of pyridine adsorption. Results are compared with those obtained for WO₃/Al₂O₃ samples prepared in the same conditions, showing that niobia is able to disperse tungsta better than alumina does. Formation of a crystalline WO₃ needs larger tungsten contents on niobia than on alumina, since tungsten solution into niobia is easier than into alumina. Raman and XAS spectra recorded under ambient conditions suggest that similar WO_x species are formed on both supports at tungsten contents 0.5–1 theoretical monolayers; however, TPR results for the low tungsten loaded samples indicate that, when reduction starts (always at temperatures higher than 700 K under H₂/Ar flow) there is a larger concentration of tetrahedral [WO₄] species on alumina, than on niobia. Samples with low tungsten loading have been tested in isopropanol decomposition and ethylene oxidation, following both processes by FT-IR of adsorbed species up to 673 K. Results show that adsorption of ethylene on WO₃/Nb₂O₅ yields acetaldehyde and acetate at 473 K, while this adsorption is non-reactive either on the supports or on WO₃/Al₂O₃. Isopropanol adsorbs dissociatively on both supports, leading to acetone and propene formation on tungsta–niobia, but only propene on tungsta–alumina, probably due to the larger reducibility of the tungsten-containing phases.     

Oxidative dehydrogenation of n-butane and 1-butene on undoped and K-doped VOx/Al2O3 catalysts

The oxidative dehydrogenation (OXDH) of n-butane and 1-butene on undoped and K-doped alumina-supported vanadia catalysts has been studied. The low selectivity to OXDH products on alumina-supported vanadia catalysts is a consequence of the isomerization of olefins (low temperatures) and the formation of carbon oxides (high temperatures) on acid sites. The presence of potassium results in a decrease of the number of acid sites and a higher selectivity to OXDH products from both n-butane and 1-butene. Infrared spectroscopy data of 1-butene adsorbed on the catalysts suggest the presence of different adsorbed species: (i) O-containing species on the undoped catalyst, or (ii) adsorbed butadiene on K-doped catalyst. A reaction network including parallel and consecutive reactions is proposed.     

V2O5 catalysts supported on Al2O3–SiO2 mixed oxide: V, H MAS solid-state NMR, DRIFTS and methanol oxidation studies

Alumina–silica mixed oxide, synthesized by the sol–gel technique, was used as a support for dispersing and stabilizing the active vanadia phase. The catalysts were characterized employing ⁵¹V and ¹H solid-state MAS NMR, diffuse reflectance FT-IR, BET surface area measurements. The partial oxidation activities of the catalysts were tested using methanol oxidation as a model reaction. ⁵¹V solid-state NMR studies on the calcined catalysts showed the peaks corresponding to the presence of both tetrahedral and distorted octahedral vanadia species at low vanadia loadings and with an increase in V₂O₅ content, the ⁵¹V chemical shifts corresponding to amorphous V₂O₅ like phases were observed. DRIFTS studies of the catalysts indicated the vibrations corresponding tetrahedral vanadia species at low and medium loadings and at high V₂O₅ contents the vibrations corresponding V=O bonds of V₂O₅ agglomerates were observed. The V/Al–Si catalysts exhibited high selectivity for the dehydration product dimethyl ether in the methanol partial oxidation studies showing the predominance of the acidic nature of the alumina–silica support over the redox properties of the active vanadia phase.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Infrared studies of nitric oxide adsorption on reduced and sulfided P-Ni-Mo/Al2O3 catalysts

A series of P-Ni-Mo/Al₂O₃ catalysts with varying phosphorus content, prepared by co-impregnation, was studied by infrared spectroscopy of nitric oxide adsorption on their reduced and sulfided form. It was found that small concentrations of phosphorus (1 to 3 wt.-% P₂O₅) increased reducibility and sulfidability of nickel and molybdenum. A red shift of the band of nitric oxide adsorbed on molybdenum is observed for sulfided samples with low phosphorus content compared to phosphorus free. In the samples with high phosphorus contents (above 4 wt.-% P₂O₅) reducibility and sulfidability of nickel and molybdenum decreases. A blue shift of the band of nitric oxide adsorbed on molybdenum is observed and three types of nickel species are found with different degree of reduction/sulfidation in the sulfided form of these samples.     

Preparation and characterization of LaCrO3 and Cr2O3 methane combustion catalysts supported on LaAl11O18- and Al2O3-coated monoliths

A series of LaAl₁₁O₁₈- and Al₂O₃-supported LaCrO₃ and Cr₂O₃ combustion catalysts was prepared. Different active phase–support combinations were prepared and applied to cordierite monoliths. The washcoat materials were aged in flowing humid air at temperatures between 1100°C and 1400°C, after which they were characterized by BET, XRD, TPR, and EDS. The monolith catalysts were evaluated in methane combustion. The presence of an active phase retarded sintering of the Al₂O₃ support, whereas the active phase slightly decreased the thermal stability of LaAl₁₁O₁₈. X-ray measurements revealed extensive interaction between support and active phase in the washcoat materials. A substituted perovskite, LaCr_1−xAl_xO₃, is proposed to be formed in nearly all samples containing both lanthanum and chromium. The accessibility of chromium decreased rapidly after aging. The activities of the Al₂O₃-supported catalysts were higher than of those supported on LaAl₁₁O₁₈, which was related to the higher surface area of the former.     

Surface characterization of Al2O3–SiO2 supported NiMo catalysts: An effect of support composition

Al₂O₃–SiO₂ mixed oxide has been investigated as a support for hydrotreating catalyst with variation of its composition [Si/(Si + Al) = 0.06, 0.12, 0.31, 0.56, 0.78] and its interaction with the surface active metals (NiMo). The composition of support and surface species (NiMo) of catalysts were characterized by specific surface area, atomic absorption, SEM-EDX, XRD, temperature programmed reduction (TPR), Raman analysis, scanning electron microscopy (STEM) and transmission electron microscopy (TEM). Incorporation of SiO₂ in Al₂O₃ promotes a weak interaction between the active phases and particularly catalyst that predominated with SiO₂ content. The oxide and sulfided catalysts characterization indicated that the effect of support is responsible to form different catalytic sites. Crystallization of MoO₃ phases and a relatively longer crystal of MoS₂ in the sulfided catalyst were attributed to an increasing SiO₂ content in the support. The catalytic behavior of the NiMo supported catalysts is explained in terms of structural changes on the surface due to the support and active metal interactions. The activity of the different catalysts evaluated in the thiophene hydrodesulfurization reaction was higher for the catalyst having lower SiO₂ content in the support.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Reaction pathways of ethane oxidative and non-oxidative dehydrogenation on γ-Al2O3 studied by temperature-programmed reaction (TP-reaction)

In this work, the reactions of ethane and ethene in an oxidizing and non-oxidizing atmosphere over γ-alumina were investigated under temperature-programmed conditions, in an attempt to estimate the possible contribution and functionality of the support in the reaction pathway of ethane ODH over MoO₃/Al₂O₃ catalysts. The results indicate that alumina contributes to the primary deep oxidation and dehydrogenation routes of ethane to CO_x and coke respectively, which proceed effectively over the acidic OH groups and the Al³⁺–O²⁻ acidic centers. On the contrary, the formation of ethylene seems to be coupled to the presence of redox sites on the catalytic surface and requires the presence of the molybdena phase. Moreover, the redox sites of the MoO_x species were found to unselectively activate the further overoxidation of the olefin to carbon oxides. Therefore, Al₂O₃ catalyzes the unselective primary oxidation of ethane to carbon oxides, whereas the molybdena phase is involved in the selective oxidative dehydrogenation (ODH) of ethane to ethene and the secondary overoxidation of ethene to CO_x.     

Preparation and characterization of mesoporous γ-Ga2O3

Mesoporous γ-Ga₂O₃ was prepared by calcination (at 773 K) of a gallia gel obtained by adding ammonia to an ethanolic solution of gallium nitrate. The corresponding powder X-ray diffraction pattern was found to be similar to that of γ-alumina; all diffraction lines could be indexed by assuming a cubic spinel-type structure having a lattice parameter a₀=0.830 nm. Nitrogen adsorption–desorption at 77 K showed the material to have a BET surface area of 120 m² g⁻¹ and a most frequent pore radius of 2.1 nm. The surface chemistry was studied by FTIR spectroscopy of adsorbed carbon monoxide at liquid nitrogen temperature. Partially hydroxylated γ-Ga₂O₃ gave main O–H stretching bands at 3692 and 3637 cm⁻¹. These hydroxyl bands were significantly perturbed by adsorbed CO, thus showing a Brønsted acid character. Lewis acidity was monitored by analyzing the C–O stretching mode of carbon monoxide adsorbed on coordinatively unsaturated Ga³⁺ ions; main IR absorption bands of Ga³⁺CO adducts were found at 2220 and 2193 cm⁻¹.     

CoMo/MgO–Al2O3 supported catalysts: An alternative approach to prepare HDS catalysts

Three different supports were prepared with distinct magnesia–alumina ratio x = MgO/(MgO + Al₂O₃) = 0.01, 0.1 and 0.5. Synthesized supports were impregnated with Co and Mo salts by the incipient wetness method along with 1,2-cyclohexanediamine-N,N,N′,N′-tetraacetic acid (CyDTA) as chelating agent. Catalysts were characterized by BET surface area, Raman spectroscopy, SEM-EDX and HRTEM (STEM) spectroscopy techniques. The catalysts were evaluated for the thiophene hydrodesulfurization reaction and its activity results are discussed in terms of using chelating agent during the preparation of catalyst. A comparison of the activity between uncalcined and calcined catalysts was made and a higher activity was obtained with calcined MgO–Al₂O₃ supported catalysts. Two different MgO containing calcined catalysts were tested at micro-plant with industrial feedstocks of heavy Maya crude oil. The effect of support composition was observed for hydrodesulfurization (HDS), hydrodemetallization (HDM), hydrodeasphaltenization (HDAs) and hydrodenitrogenation (HDN) reactions, which were reported at temperature of 380 °C, pressure of 7 MPa and space-velocity of 1.0 h⁻¹ during 204 h of time-on-stream (TOS).     

Preparation of Co–Mo/B2O3/Al2O3 catalysts for hydrodesulfurization: Effect of citric acid addition

The effect of citric acid (CA) addition was studied on the HDS of thiophene over Co–Mo/(B)/Al₂O₃ catalysts. The catalysts were characterized by means of LRS, Mo K-edge EXAFS, NO adsorption capacity measurements, and UV–vis spectra. The catalysts were subjected to a chemical vapor deposition (CVD) technique using Co(CO)₃NO as a precursor of Co in order to get deeper insights into the effect of citric acid addition. It was shown that the HDS activity was enhanced by the citric acid addition up to the CA/Mo mole ratio of around 1 and leveled off with further addition. The amount of Co anchored by the CVD was increased by the addition of citric acid, suggesting an increase in the dispersion of MoS₂ particles on the catalyst by the simultaneous presence of Co, Mo and citric acid, in conformity with the increase in the NO adsorption capacity. In contrast to Co–Mo catalysts, the edge dispersion of MoS₂ particles in Mo/B/Al₂O₃ was not affected by the addition of citric acid. The LRS, UV–vis spectra and Mo K-edge EXAFS showed that Co–CA and Mo–CA surface complexes are formed by the addition of citric acid. The Co–CA surface complex is more preferentially formed on CoMo/Al than on CoMo/B/Al, in agreement with a greater promoting effect of citric acid at a lower CA/Mo mole ratio for CoMo/Al than for CoMo/B/Al.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Al_2O_3负载钯催化剂的制备及催化Suzuki偶联反应的研究

采用浸渍-还原法制备三氧化二铝负载钯催化剂（Pd/Al2O3）,通过ICP-AES、XRD、XPS等分析手段对催化剂的结构和组成进行了表征。考察了溶剂、溶剂与水的比例、碱的种类、反应温度以及反应时间等反应条件对上述制备的催化剂催化Suzuki偶联反应的影响,筛选出最适宜的反应条件。实验结果表明,在1mmol对溴苯乙酮,1.5mmol苯硼酸,2mmol碳酸钾,乙醇∶水=6∶6,反应温度为60℃,反应时间为60min,催化剂加入量为3.5×10-3mmol钯的反应条件下,Suzuki反应收率可达97%以上。     

The effects of La2O3 on the structural properties of La2O3–Al2O3 prepared by the sol–gel method and on the catalytic performance of Pt/La2O3–Al2O3 towards steam reforming and partial oxidation of methane

The effect of La₂O₃ content on the structural properties and catalytic behavior of Pt/xLa₂O₃–Al₂O₃ catalysts in steam reforming of methane and partial oxidation of methane was investigated. There was a decrease in the density of Pt sites with the increase of La₂O₃ loadings according to Fourier transform infrared spectroscopy of adsorbed CO and to dehydrogenation of cyclohexane results. However, transmission electron microscopy data indicates an opposite trend. This apparent disagreement could be due to the partial coverage of Pt sites by LaO_x species. CH₄ turnover rates and specific rates of steam reforming of methane increased for higher La₂O₃ loadings. The Pt/Al₂O₃ catalyst was strongly deactivated during partial oxidation of methane, while La₂O₃-containing catalysts exhibited higher stability. The increase of activity observed during the reactions was ascribed to the ability of the [LaPt_xO]Pt⁰-like species to promote the gasification of coke. This cleaning mechanism led to higher accessibility of the active sites to CH₄.     

Carbon black oxidation in the presence of Al2O3, CeO2, and Mn oxide catalysts: An EPR study

Carbon black oxidation in the presence of CeO₂, Al₂O₃ and manganese oxide catalysts has been studied in tight contact conditions. In the presence of manganese based catalysts, the temperature gain is about 275 °C compared to the non-catalysed carbon black oxidation. The contribution of the manganese species to enhance the reactivity of carbon black oxidation has been evaluated by EPR technique. For Mn/Ce + CB mixtures the Mn²⁺ content considerably increases consequently to tight milled treatment indicating the reduction of some manganese species with higher oxidation states into Mn²⁺ ions. This phenomenon can be considered as the first step in the carbon black oxidation mechanism in the presence of Mn/Ce catalysts.     

Preparation, characterization and reactivity of Pd/Nb2O5 catalysts in hexa-1,5-diene hydrogenation

Palladium/niobia catalysts are prepared by various methods involving either gas or liquid phase reduction. Although giving rise to average or low dispersion, the reduction of palladium precursors in a liquid medium (hydrazine or ethylene–glycol) appears to be a promising method since a low dispersion favors the activity in the hydrogenation of hexa-1,5-diene in liquid phase. The substitution of alumina by niobia improves the fractional selectivity and the yield of hex-1-ene in all cases. A very good global selectivity is also observed.