Processing and Properties of TiB2 with MoSi2 Sinter-additive: A First Report

The densification of non-oxide ceramics like titanium boride (TiB₂) has always been a major challenge. The use of metallic binders to obtain a high density in liquid phase-sintered borides is investigated and reported. However, a non-metallic sintering additive needs to be used to obtain dense borides for high-temperature applications. This contribution, for the first time, reports the sintering, microstructure, and properties of TiB₂ materials densified using a MoSi₂ sinter-additive. The densification experiments were carried out using a hot-pressing and pressureless sintering route. The binderless densification of monolithic TiB₂ to 98% theoretical density with 2–5 μm grain size was achieved by hot pressing at 1800°C for 1 h in vacuum. The addition of 10–20 wt% MoSi₂ enables us to achieve 97%–99%ρ_th in the composites at 1700°C under similar hot-pressing conditions. The densification mechanism is dominated by liquid-phase sintering in the presence of TiSi₂. In the pressureless sintering route, a maximum of 90%ρ_th is achieved after sintering at 1900°C for 2 h in an (Ar+H₂) atmosphere. The hot-pressed TiB₂–10 wt% MoSi₂ composites exhibit high Vickers hardness (∼26–27 GPa) and modest indentation toughness (∼4–5 MPa·m^1/2).     

Pressureless Sintering of ZrB2–SiC Ceramics

A pressureless sintering process was developed for the densification of zirconium diboride ceramics containing 10–30 vol% silicon carbide particles. Initially, boron carbide was evaluated as a sintering aid. However, the formation of a borosilicate glass led to significant coarsening, which inhibited densification. Based on thermodynamic calculations, a combination of carbon and boron carbide was added, which enabled densification (relative density >98%) by solid-state sintering at temperatures as low as 1950°C. Varying the size of the starting silicon carbide particles allowed the final silicon carbide particle morphology to be controlled from equiaxed to whisker-like. The mechanical properties of sintered ceramics were comparable with hot-pressed materials with Vickers hardness of 22 GPa, elastic modulus of 460 GPa, and fracture toughness of ∼4 MPa·m^1/2. Flexure strength was ∼460 MPa, which is at the low end of the range reported for similar materials, due to the relatively large size (∼13 μm long) of the silicon carbide inclusions.     

Low-Temperature Processing of Dense Hydroxyapatite–Zirconia Composites

Hydroxyapatite (HA)–YTZP (2, 5, 7.5, and 10 wt% ZrO₂) composite powders prepared from inorganic precursors were characterized by FTIR, DSC/TG, XRD, and TEM. The calcined powders had HA and t / c -ZrO₂, which undergo structural changes between 650°C and 1050°C. TEM of calcined powder showed larger HA particles (100 nm) and smaller ZrO₂ particles (≤50 nm). HA and HA–2 wt% ZrO₂-sintered samples had 98% density and it was (90–95%) for HA–5, 7.5, and 10 wt% ZrO₂. The bending strength of HA–2wt% ZrO₂ composites was 72 MPa. The grain sizes of HA showed a refinement with ZrO₂ addition.     

Deposition of Silicon Carbide/Titanium Carbide Laminar Ceramics by Electrophoresis and Densification by Spark Plasma Sintering

SiC/TiC laminar ceramic composites were fabricated using electrophoretic deposition (EPD) from acetone-based suspensions. The growth rate of the SiC was almost twice that of the TiC at the same deposition voltage and solids loading. Pressureless sintering and spark plasma sintering (SPS) of the composites were investigated. SiC in the composites without sintering additives could not be densified using pressureless sintering, even at 2000°C. SPS, however, could densify the SiC/TiC composites at 1800°C and 35 MPa. The relative density of the SPS sample was 98.9%.     

Field-Assisted Sintering of Nanocrystalline Titanium Nitride

Nanosized TiN powder was densified via field-assisted sintering at temperatures of 1150°–1350°C and a pressure of 66 MPa under vacuum. A maximum relative density of ∼97% and a maximum mean grain size of 150–200 nm were obtained. Densification and microstructural evolution have been discussed, in terms of superplasticity and electric-field effects.     

Densification, Sintering Reactions, and Properties of Titanium Diboride With Titanium Disilicide as a Sintering Aid

In the present investigation, we explore the feasibility of using TiSi₂ as a sintering aid to densify titanium diboride (TiB₂) at a lower sintering temperature (<1700°C). The hot-pressing experiments were conducted in the temperature range of 1400°–1650°C for 1 h in an argon atmosphere and TiSi₂ addition to TiB₂ was restricted up to 10 wt%, with an overall objective to densify the materials with a fine microstructure as well as to assess the feasibility of enhancing the mechanical and electrical properties. When all the materials were hot pressed at 1650°C, the hot-pressed TiB₂– X % TiSi₂ ( X =0, 2.5, 5, 10 wt%) composites were found to be densified to more than 98%ρ_th (theoretical density), except monolithic TiB₂ (∼94%ρ_th). An interesting observation is the formation of a Ti₅Si₃ phase and this phase formation is described by thermodynamically feasible sintering reactions. Our experimental results suggest that the optimal TiB₂–5 wt% TiSi₂ composite can exhibit an excellent combination of properties, including a high hardness of 25 GPa, an elastic modulus of 518 GPa, an indentation toughness of ∼6 MPa·m^1/2, a four-point flexural strength of more than 400 MPa, and an electrical resistivity of 10 μΩ·cm.     

Sintering of in-Situ Synthesized Sic–TiB2 Composites with Improved Fracture Toughness

TiB₂-particle reinforcement is one of the most successful methods for improving the fracture toughness of SiC ceramics.^1–3 Commercially available TiB₂ powders, however, have a large particle size and/or are highly reactive so that they are not favorable as a starting powder. In the present work, TiB₂ particles are formed by an in situ reaction between TiC and boron. The reaction takes place during sintering between 1000° and 1600°C and is accompanied by a large volume expansion. Under optimum conditions, dense composites (> 98% of theoretical) can be obtained by pressureless sintering using B and C as sintering additives. The in situ reaction method enables, for the first time, a complete densification of SiC-particulate composites by pressureless sintering. The fracture toughness of the composites was approximately 30% higher than that of the monolithic SiC ceramic.     

Development of WC–ZrO2 Nanocomposites by Spark Plasma Sintering

In the present work, we report the processing of ultrahard tungsten carbide (WC) nanocomposites with 6 wt% zirconia additions. The densification is conducted by the spark plasma sintering (SPS) technique in a vacuum. Fully dense materials are obtained after SPS at 1300°C for 5 min. The sinterability and mechanical properties of the WC–6 wt% ZrO₂ materials are compared with the conventional WC–6 wt% Co materials. Because of the high heating rate, lower sintering temperature, and short holding time involved in SPS, extremely fine zirconia particles (∼100 nm) and submicrometer WC grains are retained in the WC–ZrO₂ nanostructured composites. Independent of the processing route (SPS or pressureless sintering in a vacuum), superior hardness (21–24 GPa) is obtained with the newly developed WC–ZrO₂ materials compared with that of the WC–Co materials (15–17 GPa). This extremely high hardness of the novel WC–ZrO₂ composites is expected to lead to significantly higher abrasive-wear resistance.     

Tetragonal Zirconia Polycrystals Reinforced with SiC Whiskers

The microstructure and the mechanical properties of hot-pressed tetragonal ZrO₂ polycrystals (TZP) reinforced with up to 30 vol% SiC whiskers were studied. The SiC whisker-TZP composites were stable under the hot-pressing conditions at 1450°C. Annealing in an oxidizing atmosphere at ∼1000°C resulted in glass formation and microcracking caused by whisker oxidation and transformation of the ZrO₂ grains near the whiskers to monoclinic symmetry. The fracture toughness was markedly improved by the dispersed whiskers (∼12 Mpa·m^1/2 at 30 vol% SiC) compared to the values measured for the matrix (∼6 Mpa·m^1/2). The flexural strength of the hot-pressed TZP-30 vol% SiC whisker composite at 1000°C (∼400 MPa) was twice that of the TZP matrix.     

Reaction Synthesis of Aluminum Nitride–Boron Nitride Composites Based on the Nitridation of Aluminum Boride

Aluminum nitride–boron nitride (AlN–BN) composites were prepared based on the nitridation of aluminum boride (AlB₂). AlN powder was added to change the BN volume fraction in the obtained composites. Thermogravimetry–differential thermal analysis (TG-DTA), X-ray diffractometry, and the nitridation ratio were used to investigate the nitridation process of AlB₂. At ∼1000°C, a sharp exothermic peak occurred in the DTA curve, corresponding to the rapid nitridation of aluminum in AlB₂. On the other hand, the nitridation of the transient phase, Al_1.67B₂₂, was very slow when the temperature was <1400°C. However, the nitridation speed obviously accelerated at temperatures >1600°C. The pressure of the nitrogen atmosphere was also an important factor; high nitrogen pressure remarkably promoted nitridation. Treatment at 2000°C was disadvantageous for nitridation, because of the rapid formation of a dense surface layer that inhibited nitrogen diffusion into the specimen interior. Three specimens, with 5 wt% Y₂O₃ additive and different BN contents, were prepared by pressureless reactive sintering, according to the determined sintering schedule. Electron microscopy (scanning and transmission) observations revealed that the in-situ -formed BN flakes were homogeneously and isotropically distributed in the AlN matrix. A schematic mechanism for microstructural formation was developed, based on the results of nitridation and the microstructural features of the obtained composites. The obtained composites, with a low BN content, exhibited a high bending strength, comparable to that of reported hot-pressed AlN–BN composites.     

Combustion Synthesis of Silicon Nitride-Silicon Carbide Composites

The feasibility of synthesizing silicon nitride-silicon carbide composites by self-propagating high-temperature reactions is demonstrated. Various mixtures of silicon, silicon nitride, and carbon powders were ignited under a nitrogen pressure of 30 atm (∼ 3 MPa), to produce a wide composition range of Si₃N₄-SiC powder products. Products containing up to 17 vol% of SiC, after being attrition milled, could be hot-pressed to full density under 1700°C, 3000 psi (∼ 21 MPa) with 4 wt% of Y₂O₃. The microhardness and fracture toughness of these composites were superior to those of the pure β-Si₃N₄ matrix material and compared very well with the properties of "traditionally" prepared composites.     

New Uniformly Porous CaZrO3/MgO Composites with Three-Dimensional Network Structure from Natural Dolomite

Porous CaZrO₃/MgO composites with a uniform three-dimensional (3-D) network structure have been successfully synthesized using reactive sintering of highly pure mixtures of natural dolomite (CaMg(CO₃)₂) and synthesized zirconia powders with LiF additive. Equimolar dolomite and zirconia powders doped with 0.5 wt% LiF were cold isostatically pressed at 200 MPa and sintered at 1100–1400°C for 2 h in air. Through the liquid formation via LiF doping, strong necks were formed between constituent particles before completion of the pyrolysis of dolomite, resulting in the formation of a 3-D network structure. During and after the formation of the network structure, CO₂ was given off to form a homogeneous open-pore structure. The pore-size distribution was very narrow (with pore size ∼ 1 μm), and the porosity was controllable (e.g., ∼30%–50%) by changing the sintering temperature. The porous composites can be applied as filter materials with good structural stability at high temperatures.     

Sintering and Characterization of Nanophase Zinc Oxide

Nanocrystalline, single-phase undoped ZnO was sintered to 95%–98% of theoretical density at 650°–700°C, using pressureless isothermal sintering. The density increased very rapidly at 500°–600°C, remained constant with sintering temperature until ∼900°C, and then decreased slightly. The estimated activation energy for densification at 600°–700°C (275 kJ/mol) was comparable to grain-growth activation energies previously reported for microcrystalline ZnO but much greater than the grain-growth activation energy measured in the present work. A bimodal microstructure, consisting of nanocrystalline grains within larger ensembles ("supergrains"), was observed, and both modes grew as the sintering temperature increased. The grain-growth activation energy for the nanocrystalline grains was extremely low, ∼20 kJ/mol. The activation energy for the growth of the supergrains depended strongly on temperature but was ∼54 kJ/mol at >500°C. The important mechanisms probably are rearrangement of the nanoparticle grains, with simultaneous surface and boundary diffusion, and vapor transport above 900°C.     

In Situ Synthesis of Ultrafine ZrB2–SiC Composite Powders and the Pressureless Sintering Behaviors

Ultrafine ZrB₂–SiC composite powders have been synthesized in situ using carbothermal reduction reactions via the sol–gel method at 1500°C for 1 h. The powders synthesized had a relatively smaller average crystallite size (<200 nm), a larger specific surface area (∼20 m²/g), and a lower oxygen content (∼1.0 wt %). Composites of ZrB₂+20 wt% SiC were pressureless sintered to ∼96.6% theoretical density at 2250°C for 2 h under an argon atmosphere using B₄C and Mo as sintering aids. Vickers hardness and flexural strength of the sintered ceramic composites were 13.9±0.3 GPa and 294±14 MPa, respectively. The microstructure of the composites revealed that elongated SiC grain dispersed uniformly in the ZrB₂ matrix. Oxidation from 1100° to 1600°C for 30 min showed no decrease in strength below 1400°C but considerable decrease in strength with a rapid weight increment was observed above 1500°C. The formation of a protective borosilicate glassy coating appeared at 1400°C and was gradually destroyed in the form of bubble at higher temperatures.     

Fabrication of Stainless-Steel-Fiber-Reinforced Cordierite-Matrix Composites of Tubular Shape Using Electrophoretic Deposition

Stainless-steel (316L) fiber mats shaped into tubular geometry were used to reinforce cordierite. The cordierite-matrix composites were manufactured using electrophoretic deposition and pressureless sintering. The sintered composites, which had an internal and external deposit thickness of ∼1 mm, were free of surface cracks when a deposition time of 2.5 min was used. Metal-fiber-reinforced cordierite composites such as those developed here may constitute a promising alternative for manufacturing damage-tolerant tubular components for applications at temperatures up to ∼900°C.     

Differential Sintering by Improper Selection of Sintering Parameters during Pulse Electric Current Sintering

Recently, we reported on the retention of fine-grained micro-structure in Al₂O₃/3 vol% 3Y-ZrO₂ composites using the pulse electric current sintering (PECS) technique. It was demonstrated that a high heating rate is beneficial for the retention of fine grains and homogeneous microstructure. As there are few reports on microstructural inhomogeneity and excessive grain growth in compacts densified by the PECS technique, we carried out a series of experiments on monolithic alumina by varying the sintering parameters and discussed the characteristic results. All specimens that were densified under selective sintering conditions attained high density (∼99% of the theoretical density) at 1250°3C in > 5 min. The average fracture strength of monolithic alumina was observed to be 741 ± 25 MPa and the fracture toughness was 2.2 MPa.m <^1/2, and these were reasoned out to small grains. However, compacts sintered under very low compaction pressure attained ∼92%-93% of the theoretical density, and these specimens had undesirable microstructural inhomogeneity owing to differential sintering. Hence, in the present study, we address the problem of differential sintering.     

Effect of Hot Isostatic Pressing on Reaction-Bonded Silicon Nitride

Reaction-bonded silicon nitride was isostatically hot-pressed under 138 MPa for 2 h at 1850°, 1950°, or 2050°C. Nearly theoretically dense specimens resulted. The room-temperature flexural strength more than doubled, but the 1200°C flexural strength increased significantly only after pressing at 2050°C.f. ∼35% improvement). An amorphous phase introduced by hot isostatic pressing accounts in part for these results.     

The Study on Carbon Nanofiber (CNF)-Dispersed B4C Composites

Carbon nanofiber (CNF)-dispersed B₄C composites have been synthesized and consolidated directly from mixtures of elemental raw powders by pulsed electric current pressure sintering (1800°C/10 min/30 MPa). A 15 vol% CNF/B₄C composite with ∼99% of dense homogeneous microstructures (∼0.40 μm grains) revealed excellent mechanical properties at room temperature and high temperatures: a high bending strength (σ_b) of ∼710 MPa, a Vickers hardness ( H _v) of ∼36 GPa, a fracture toughness ( K _{I C} ) of ∼7.9 MPa m^1/2, and high-temperature σ_b of 590 MPa at 1600°C in N₂. Interfaces between the CNF and the B₄C matrix were investigated using high-resolution transmission electron microscopy, EDS, and electron energy-loss spectroscopy.     

Fine-Grained Silicon Carbide Ceramics with Oxynitride Glass

By using an oxynitride glass composition from the Y-Mg-Si-Al-O-N system as a sintering additive, the effect of atmosphere on densification was investigated during the liquid-phase sintering of SiC, and the resulting microstructure and mechanical properties of the sintered and subsequently annealed materials were investigated. SiC ceramics that were densified with 10 wt% oxynitride glass showed higher sinterability in a nitrogen atmosphere. Oxynitride glass enlarged the stability region of β-SiC and suppressed β→ alpha phase transformation, which resulted in an equiaxed microstructure. Grain growth of fine-grained SiC in some extent (up to ∼300 nm) was beneficial in improving both room-temperature strength and toughness. The best results were obtained when the ceramics were hot-pressed at 1800°C for 1 h in a nitrogen atmosphere and subsequently annealed at 1900°C for 3 h in an argon atmosphere. The room-temperature flexural strength and fracture toughness of the material were 847 MPa and 3.5 MPa·m^1/2, respectively.     

Densification and Phase Transformation of β-SiAlON–Cubic Boron Nitride Composites Prepared by Spark Plasma Sintering

β-SiAlON–cubic boron nitride (cBN) composites were prepared from β-SiAlON and cBN powders at 1600°–1900°C under a pressure of 100 MPa by spark plasma sintering. The effects of cBN content and sintering temperature on densification and phase transformation of the β-SiAlON–cBN composites were studied. When 10–30 vol% cBN was added to β-SiAlON, the shrinkage rate of the compacts increased. The compacts of β-SiAlON–BN composites originally containing 10–30 vol% cBN ceased to shrink at a temperature lower than that of β-SiAlON and the density of the composites increased. The densification of β-SiAlON–BN composites originally containing >40 vol% cBN was suppressed. The phase transformation of cBN to hexagonal BN in the β-SiAlON–BN composite was inhibited to a greater degree than that in the cBN body.