[1,3,4]-噁二唑衍生物的固相合成及其线性、非线性光谱性质

用固相法合成了2个噁二唑衍生物类有机化合物:5-(4-叔丁基苯基)-[1,3,4]噁二唑-2-苯乙烯基-4-苯基-二苯胺 (化合物1)与9-乙基-3,6-双{5-(4-叔丁基苯基)-[1,3,4] 噁二唑-2-苯乙烯基}-咔唑 (化合物2),并测定了它们的吸收光谱、单光子荧光光谱和双光子荧光光谱.化合物1和2在二氯甲烷溶液中单光子荧光发射峰分别位于519和476nm.在锁模Nd∶YAG激光器800nm激光照射下,化合物1和2发射出很强的双光子上转换荧光,其最大波长分别在520和485nm.     

侧链含噻吩基团的改性乙烯基咔唑聚合物的合成与表征

利用Suzuki反应,合成了侧链含噻吩基团的改性乙烯基咔唑单体,采用阴离子聚合方法制备了一种新型改性聚乙烯基咔唑。通过1H核磁共振谱、红外光谱(FT-IR)、差示扫描量热法(DSC)、凝胶渗透色谱、质谱(EI)、UV-vis紫外-可见吸收光谱、荧光发射光谱等方法对单体及聚合物进行了表征,结果发现改性聚乙烯基咔唑的数均分子量-Mn=2486,多分散系数PDI=1.10。紫外-可见光谱结果表明,含噻吩基团的改性乙烯基咔唑聚合物相对于乙烯基咔唑所对应的吸收峰有红移,且吸收强度增大。荧光发射光谱结果表明,聚合物较单体原料的最大发射波长红移了100nm,可作为太阳能电池给体材料应用。     

两种新型咔唑类双光子光聚合引发剂的合成与光学性质

报道了两种新型的咔唑类双光子光聚合引发剂,3,6-双[2-（4-吡啶基）乙烯基]-9-苯基咔唑（1） 和 3,6-双[2-（2-吡啶基）乙烯基]-9-苯基咔唑（2）,它们是通过钯催化的Heck偶连反应合成得到,并用元素分析,红外光谱,核磁共振氢谱和电喷雾电离质谱等对它们进行了全面的表征.这两个A-π-D-π-A结构的咔唑衍生物具有很好的单光子和双光子荧光行为,我们也详细研究了它们的溶剂效应和作为双光子引发剂用于微结构的制备,并讨论了它们的引发聚合的机理.     

新型双光子聚合引发剂的合成和非线性光学性质的研究

合成了两种新的双光子聚合引发剂反式-二苯基-{{4-[2-(4-吡咯基-1-苯基)-乙烯基]-苯基}胺(简称DPVPA)和反式-9-{4-[2-(4-吡咯基-1-苯基)-乙烯基]-苯基]-9-氢咔唑(简称PPVPA).用1H NMR谱和元素分析进行了表征.测试了紫外吸收光谱、单光子荧光光谱、单光子荧光寿命和双光子荧光光谱.在760 nm的飞秒脉冲激光激发下,DPVPA和PPVPA均发出较强的上转换荧光,荧光峰分别位于468和452 nm.以DPVPA做引发剂,加入丙烯酸酯型齐聚物(CN120C80),用DATACHROOM-5000纳秒激光器辐射出600nm的激光做光源,实现了双光子聚合反应,并定性地解释了其聚合机理.     

2-甲基-8-（9，9-二丁基芴）-3，5，7-三炔-2-辛醇的合成和性质研究

合成了一种新颖的乙炔衍生物，2-甲基-8-（9，9-二丁基芴）-3，5，7-三炔-2-辛醇（6a），并利用红外光谱（IR），紫外光谱（Uv），核磁（NMR），质谱（MS）等对其结构进行了表征。利用红外光谱（IR）和紫外光谱（Uv）对其拓扑固相聚合性质进行了研究。实验结果表明，这些化合物在加热和紫外光照射条件下都能够发生固相聚合，但得到的是结构复杂的聚合物。     

一种新型含卟啉的环金属化有机配体的设计、合成与性质

采用Aldol、Adler缩合、Michael加成、Vils-meier和Knoevenagel等反应合成一种新型的D-π-A型的含C∧N∧N结构的环金属化有机配体：反式-4-[2-（5,10,15,20-四苯基卟啉基）乙烯基]-N-{4-[（2-苯基-6-吡啶基）吡啶]苯甲基}吡啶溴盐（简写为TPPB）。用核磁共振氢谱、碳谱和电喷雾质谱等手段对其结构进行了表征,初步研究了该化合物的紫外-可见光谱、荧光光谱、电化学和热稳定性。结果表明目标化合物有较好的溶解性和荧光性质,为寻找新的发光材料进行了有益的探索。     

新型对称含咔唑类发光材料的合成及性能研究

由4,4′-磺酰基二苯酚与9-(4-溴丁基)-9H-咔唑等含有链状烷基的咔唑取代产物经威廉姆逊合成法制得一系列对称含有咔唑类化合物。通过红外光谱和核磁氢谱确定其结构,通过紫外光谱、荧光光谱热重分析和循环伏安等手段对目标化合物的性能进行表征。结果表明:其最大吸收波长在290~295nm之间,溶液中荧光发射波长处于378~423nm之间,固态时荧光发射波长处于375~390nm之间,荧光量子产率在0.38~0.44之间。在热稳定性方面,热分解温度(T_d)均大于350℃,熔点(T_m)为185℃,且玻璃态转化温度(T_g)在50~120℃之间,具有良好的热稳定性。有望成为优良的有机电致发光材料。     

一种超支化共轭聚合物的合成与2,4-二硝基甲苯的荧光猝灭

以2,4,6-三甲基均三嗪和甲酰基咔唑、二甲酰基咔唑为原料,通过羟醛缩合反应合成了化合物I及超支化荧光共轭聚合物II,其中I可以视为II的组成单体。聚合物II在常见有机溶剂中有较好的溶解度,其X射线衍射谱图中2θ=24.2°的位置有1个较宽的峰;其吸收和荧光光谱与I的相比仅有轻微红移(3nm),这些结果都说明聚合物II分子间没有紧密的π-π堆积作用。聚合物II的荧光强度是化合物I的2倍。2,4-二硝基甲苯对其荧光猝灭研究结果表明,超支化聚合物II具有比化合物I更大的荧光猝灭常数(Ksv=95.52L/mol),表现出了一定的分子导线效应。     

脉冲偏压对等离子体沉积DLC膜化学结构的影响

以乙炔为气源，用等离子体基脉冲偏压沉积（plasma based pulsd bias deposition缩写PBPBD）技术进行了不同负脉冲偏压条件下制备DLC膜的试验，通过X射线光电子谱（XPS）、激光喇曼光谱[Raman]以及电阻分析方法考察了负脉冲偏压幅值对DLC膜化学结构的影响，结果表明由-50kV到-10kV随负脉冲偏压降低，DLC膜中SP^3键分数单调增加，但当脉冲偏压为0时形成高电阻的类聚合物膜，说明荷能离子的轰击作用形成DLC化学结构的必要条件，键角混乱度和SP^2簇团尺寸与脉冲偏压之间不具有单调关系，在中等幅值负脉冲偏压条件下，键用混乱度较大且SP^2簇团尺寸细小。     

含咔唑基氨基硫脲类汞离子探针的合成及其性能研究

以3-甲酰基-N-丁基咔唑和4-苯基-3-硫代氨基脲为反应原料,合成了一种基于咔唑的席夫碱衍生物L(3-甲酰基-N-丁基咔唑缩4-苯基-3-硫代氨基脲席夫碱),用IR、1 H NMR及元素分析对其结构进行了表征。通过紫外-可见光谱、荧光光谱及1 H NMR谱研究了L对Hg2+的选择性识别性能。实验结果表明,L与Hg2+能够以2∶1的化学计量比形成配合物,结合常数为7.6×104 L/mol,且L对Hg2+有很好的选择性,受常见离子的干扰较小。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from