滑条式静磁微执行器的pull-in现象分析

从滑条式静磁微执行器的模型出发,应用静磁微执行器的pull—in方程,分析了滑条式静磁微执行器的pull-in现象,用磁动势控制模型和力学平衡两种方式得出了执行器的吸合位置及吸合时的磁动势.对于特定的滑条式磁微执行器结构,pull-in位置为初始气隙宽度的1／3处．算例计算结果表明,该静磁微执行器的pull-in磁动势仅为3．84A．     

软夹芯夹层梁最大弯曲正应力的计算

最大弯曲正应力是衡量夹层梁弯曲性能的重要参数之一,本文推导出了将软夹芯夹层梁等效成等截面均质单层梁计算最大弯曲正应力的方法,并在此基础上进行三点弯曲试验的算例研究。结果表明:修正单层梁理论与层合梁理论计算的结果是一致的。当破坏载荷与夹层梁横截面的尺寸一定时,随着芯层与总厚度比的增加,修正单层梁理论计算的最大正应力值逐渐增加,而单层梁理论计算的结果为一恒定值。最大弯曲正应力修正公式的建立为夹层梁的工程应用提供理论基础。     

一种新型MEMS开关微驱动器研究与仿真

介绍了一种基于光致形变聚合物材料的MEMS开关微驱动器。光致形变聚合物材料在光驱动型微执行器上的应用具有体积小、结构简单、易实现遥控等特点。根据MEMS的尺寸及性能要求建立开关及微驱动器模型,并得到所需最大驱动力。通过计算得出具有一定尺寸光致形变薄膜的等效弯曲行为,并将其应用到MEMS开关微驱动器上。运用ANSYS对微驱动器及闭锁机构仿真分析,根据仿真结果对结构进行改进,确定了采用多层薄板结构的方案,以满足最大驱动力要求。     

基于ANSYS的静电微执行器吸合现象分析

本文基于静电场和弹性薄板理论,对MEMS静电结构的吸合现象进行了理论分析并给出公式化结果。然后借助于有限元分析软件ANSYS,对微开关中的静电驱动微悬臂梁进行分析,得到其吸合现象对应参数的标准数值,最后实现理论数值和标准数值的比较,以期对MEMS微执行器设计提供一定的理论支撑。     

腹腔镜手术剪的设计与研究

腹腔镜手术工具是否具备弯曲功能影响了手术工具的工作范围和易用性。本文对两种腹腔镜手术剪工作部建立了结构模型、力学模型及运动’力学模型,并建立其与工具控制部受力、行程的关系,同时用调查得到的合理的人机尺寸进行约束。其次,对腹腔镜手术剪弯转部进行了内含万向轴的多套层结构设计,使得主杆部实现固定角度弯曲的同时,还可实现前端变角度（0—80度）弯曲以及剪动工作部可随套层做轴向旋转,使手术工具整体能够完成S型弯曲和L型弯曲,扩大了腹腔镜手术工具的操作范围及灵活度,提高了手术工作效率。     

基于修正单层梁理论的夹层梁最大弯曲正应力计算

目的计算夹层梁横截面的最大弯曲正应力。方法将夹层梁等效成等截面均质单层梁,进而推导出了理论计算公式,并在此基础上进行了三点弯曲试验的算例研究。结果当破坏载荷与夹层梁横截面的尺寸一定时,随着芯层与总厚度比的增加,修正单层梁理论计算的最大正应力值逐渐增加,而单层梁理论计算的结果为恒定值。对于同样结构的夹层梁,随着芯层弹性模量与表层模量比的增加,修正单层梁理论计算的最大正应力与单层梁理论的差异值越来越小。结论修正单层梁理论与层合梁理论计算的结果是一致的,该方法可有效进行最大弯曲正应力的预测与计算。     

高精密厂房中高精密平台控制仿真模拟

为进一步提高高精密厂房中平台的隔振效果,在平台控制中考虑超磁致伸缩作动器的非线性特性对多自由度平台混合控制系统产生一定的制约作用,因此将四个超磁致伸缩作动器模型植入混合控制系统进行设计。首先建立一个以空气弹簧和超磁致伸缩作动器为基本元件的多自由度微振动混合控制系统,然后利用Jiles-Atherton模型的概念建立超磁致伸缩作动器的非线性及其逆补偿模型,并将所建立的作动器模型与多自由度微振动控制系统结合。最后对基于作动器模型的混合控制系统与被动控制系统下的高精密平台响应进行对比分析,取得较好的控制效果,为其在实际工程应用中提供可靠的理论依据。     

高阶剪切变形板理论下FG-GRC板的屈曲和弯曲分析

基于三阶剪切变形板理论(TSDPT)和正弦剪切变形板理论(SSDPT),研究了功能梯度石墨烯增强复合材料(FG-GRC)板的屈曲和弯曲行为,并通过与一阶剪切变形板理论(FSDPT)计算结果的比较,分析了TSDPT、SSDPT与FSDPT在FG-GRC板屈曲和弯曲力学行为研究过程中的差异。材料的有效杨氏模量通过修正的Halpin-Tsai微观力学模型估算,有效泊松比通过混合律确定。利用最小势能原理推导出了包含五个未知量的控制方程,并获得了简支FG-GRC矩形板弯曲挠度和临界屈曲载荷Navier形式的解析解。数值结果表明：与TSDPT和SSDPT相比,FSDPT明显高估了FG-X型FG-GRC板的临界屈曲载荷而明显低估了其弯曲挠度,且略微低估了FG-O型FG-GRC板的临界屈曲载荷而略微高估了其弯曲挠度,而UD型和FG-A型FG-GRC板在三种理论下的计算结果几乎完全一致;TSDPT和SSDPT在计算FG-GRC板的弯曲挠度和临界屈曲载荷时结果十分相近;当板的总层数NL小于10层～15层时,弯曲载荷比率和临界屈曲载荷比率的变化非常显著,当总层数NL超过10层～15层时,弯曲载荷比率和临界屈...     

扶手椅型单壁碳纳米管的扭转和弯曲变形

实验提出了一种针对单壁碳纳米管的原子尺度有限元模型.利用该模型对(5,5)型扶手椅型单壁碳纳米管的扭转和弯曲变形过程进行了模拟,发现其屈曲的临界扭转和纯弯曲角度分别约为40°和20°,与扭转屈曲相比,该碳管更容易发生弯曲屈曲.当弯扭复合变形时发生屈曲后,卸载时壁面褶皱的回复比较缓慢.在某些情况下,碳管的局部势能的变化与经典连续介质力学理论不一致,对此本文结合原子势理论给出了模拟结果的原子尺度的解释.     

基于能量法的变截面层合管整体稳定承载力计算方法

为计算变截面层合管杆件整体稳定承载力,提出一种基于能量法的理论计算模型。采用基于三维梁理论的层合管等效抗弯刚度计算方法,计算了等截面段、变截面段的等效工程弹性系数。在考虑剪切变形的影响以及杆件变截面对轴压挠曲线函数影响的基础上,基于能量法推导了变截面杆整体稳定承载力解析公式。以NASA复合材料变截面杆为算例,进行了理论计算和有限元数值模拟,结果显示:同时考虑上述两因素的理论计算结果与有限元结果最为接近,剪切变形对临界承载力的修正可达10%以上,轴压挠曲线函数的变化对承载力的修正约为1%,可忽略。以锥长和锥角为参数,对变截面杆的承载力、体积和承载效率进行双参数分析,发现变截面对弯曲变形能的影响远大于对剪切变形性能的影响,采用变截面形式能够提高层合管承载效率,且一定锥长下存在承载效率最高对应的最优锥角。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...