共查询到20条相似文献,搜索用时 62 毫秒
1.
1事故情况
某电厂在运行时,石灰石系统发生故障,石灰石粉仓停止向炉膛输送石灰石粉,但石灰石粉车仍继续向粉仓输送石灰石粉,致使粉仓坍塌。此时,石灰石粉仓体自重约59t,石灰石粉重约130t。 相似文献
2.
3.
循环流化床机组的石灰石粉制备站,由于占地面积较大,通常布置在远离锅炉房的区域,从而导致石灰石粉输送系统运行能耗较大.本文结合国内某300 MW循环流化床(circulating fluidized bed,CFB)锅炉电厂石灰石粉系统改造项目,介绍一种紧凑型石灰石粉制备站的设计和应用,实现了制备站抵近锅炉房布置设计,为今后工程石灰石粉系统的优化设计提供了一种新思路. 相似文献
4.
循环流化床机组石灰石粉输送系统浅析 总被引:1,自引:0,他引:1
简要介绍了循环流化床机组通常采用的石灰石粉输送系统,通过对两种石灰石粉输送系统的比较,对CFB锅炉的石灰石粉输送系统设计提出建议. 相似文献
5.
外高桥电厂1、2号机组湿式烟气脱硫装置,是目前上海火力发电厂中的第一台大型脱硫装置。介绍了该脱硫装置的主要设备和运行系统构成,特别是详细介绍了该装置采用的新型螺旋式喷嘴、石灰石干式磨机和石灰石粉的气力输送、石膏浆液的长距离输送等技术。 相似文献
6.
CFB锅炉石灰石粉制备系统研究 总被引:1,自引:0,他引:1
循环流化床(CFB)锅炉石灰石粉制备系统的产品粒度分布特性直接影响着炉内脱硫效果及石灰石粉的利用率,细碎和分选是石灰石粉粒度控制的关键环节.为有效控制石灰石粉粒度和降低生产成本,越来越多拥有CFB锅炉的电厂放弃外购成品石灰石粉,选择在厂内配置石灰石粉制备系统.结合工程实例,简单介绍石灰石的细碎和分选设备,重点对“AUBEMA破碎机+振动筛”、“柱磨机+瀑流式选粉机”和FAM公司细碎机等3种石灰石粉制备系统的技术经济性进行了对比和分析.研究结果表明,柱磨机配套瀑流式选粉机的制备系统具有经济性好、单机出力大、对石灰石粉含水率不敏感、维护工作量小等优点,是大型CFB锅炉石灰石粉制备系统较为合理的选择. 相似文献
7.
内江高坝发电厂 410t/h循环流化床锅炉 (CFB)是引进芬兰奥斯龙公司的PYROFLOWCFB锅炉。其石灰石系统如图 1所示。石灰石经一级锤击式破碎机破碎后 ,由皮带输送机送至炉前石灰石仓 ,然后 ,通过刮板输送机送入二级破碎机 ,成品由仓泵提升输送至炉前缓冲仓 ,再由 2套气力输送装置 ,经 4根循环灰管与循环灰、给煤一起送入炉膛。该系统自 1996年 4月11日机组并网发电以来 ,一直不能正常运行 ,主要问题是二级破碎机漏粉严重、系统堵塞、缓冲仓锥斗漏粉。图 1 石灰石系统1 二级破碎机漏粉二级破碎机是美国宾夕法尼亚破碎机公司B… 相似文献
8.
9.
海外某核电站联合泵房,设计使用年限为60 a,输送介质为海水.由于当地资源限制,施工用混凝土的矿物掺合料无法使用粉煤灰,只能采用石灰石粉.基于核电站联合泵房工作环境及其混凝土设计情况,分析石灰石粉应用问题及对策,通过试验论证,解决石灰石粉矿物掺合料在适用性、掺量、氯离子扩散系数等方面存在的问题,并首次将石灰石粉混凝土应... 相似文献
10.
11.
12.
13.
Yuan Chen Westergard L. Mojarradi M.M. Johnson T.W. Cozy R.S. Billman C. Burke G.R. Kolawa E.A. 《Device and Materials Reliability, IEEE Transactions on》2006,6(2):146-153
A design for reliability methodology has been developed for electronics for low-temperature applications. A hot carrier aging (HCA) lifetime projection model is proposed to take into account the HCA impact on technology, analysis of parametric degradation versus critical circuit path degradation, transistor bias profile, transistor substrate current profile, and operating temperature profile. The most applicable transistor size can be determined in order to meet the reliability requirements of the electronics operating under low temperatures. This methodology and approach can also be applied to other transistor-level failure and/or degradation mechanisms for applications with varying temperature ranges. 相似文献
14.
15.
《Power Delivery, IEEE Transactions on》1998,13(1):73-77
IEEE Standard 1344, Synchrophasors for Power Systems, was completed in 1995. It sets parameters required to ensure that phasor measurement will be made and communicated in a consistent manner. It specifies requirements for the timing signal used for phasor synchronization and the time code needed for input to a measurement unit. GPS is the recommended time source and IRIG-B is the basic format used for time communication. The standard requires correlating phasors computed from unsynchronized and synchronized sampling to a common basis. Timetagging accurately and consistently is essential for wide area comparison of phase. The standard specifies information exchange and control message formats. These include data output, configuration, and command messages. It includes 7 annexes that discuss the concepts covered in the body of the standard 相似文献
16.
17.
18.
19.
20.
分析了GIS断路器故障原因,介绍了检验过程与充气检查、监督情况,并提供一些可借鉴的成功经验。 相似文献