Synthesis of sawtooth-like Li4Ti5O12 nanosheets as anode materials for Li-ion batteries

Hierarchical layered hydrous lithium titanate and Li₄Ti₅O₁₂ microspheres assembled by nanosheets have been successfully synthesized via a hydrothermal process and subsequent thermal treatment. The electrochemical properties of the two samples have been investigated by galvanostatic methods. The former, with the obvious layered structure and a large surface area, delivers a reversible capacity of 180 mA h g⁻¹ after 200 cycles at 200 mA g⁻¹. As for Li₄Ti₅O₁₂, with the intriguing and unique sawtooth-like morphology, it presents exceptional high rate performance and excellent cycling stability. Up to 132 mA h g⁻¹ is obtained after 200 cycles at 10,000 mA g⁻¹ (57 C), proving itself promising for high-rate applications.     

Effect of particle dispersion on high rate performance of nano-sized Li4Ti5O12 anode

Nano-sized Li₄Ti₅O₁₂ powders with high dispersivity were fabricated by a sol-gel process using P123 as surfactant, which exhibited much better high rate performance towards Li⁺ insertion/extraction as compared to the densely aggregated Li₄Ti₅O₁₂ particles although the primary grain sizes of both samples were almost the same. The Li₄Ti₅O₁₂ electrode prepared from the well-dispersed nanopowders can preserve 88.6% of the capacity at 0.1 A g⁻¹ when being cycled at 1 A g⁻¹, which is obviously higher than that of the densely aggregated sample, in which only 30% capacity can be retained. By improving the dispersivity, the specific surface area of the Li₄Ti₅O₁₂ nanoparticles, hence the electrode-electrolyte contact area was increased; meanwhile, more homogeneous mixing of the active materials with carbon black was achieved. All these factors might have resulted in the better high rate performance.     

The preparation and characterization of Li4Ti5O12/carbon nano-tubes for lithium ion battery

Li₄Ti₅O₁₂/carbon nano-tubes (CNTs) composite was prepared by sol-gel method while Ti(OC₄H₉)₄, LiCH₃COO·2H₂O and the n-heptane containing CNTs were used as raw materials. The characters of Li₄Ti₅O₁₂/CNTs composite were determined by XRD, SEM, and TG methods. Its electrochemical properties were measured by charge-discharge cycling and impedance tests. It was found that the prepared Li₄Ti₅O₁₂/CNTs presented an excellent rate capability and capacity retention. At the charge-discharge rate of 5C and 10C, its discharge capacities were 145 and 135 mAh g⁻¹, respectively. After 500 cycles at 5C, the discharge capacity retained as 142 mAh g⁻¹. It even could be cycled at the rate of 20C. The excellent electrochemical performance of Li₄Ti₅O₁₂/CNTs electrode could be attributed to the improvement of electronic conductivity by adding conducting CNTs and the nano-size of Li₄Ti₅O₁₂ particles in the Li₄Ti₅O₁₂/CNTs composite.     

Influence of composite LiCl-KCl molten salt on microstructure and electrochemical performance of spinel Li4Ti5O12

A series of spinel Li₄Ti₅O₁₂ samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li₄Ti₅O₁₂. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li₄Ti₅O₁₂ with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li₄Ti₅O₁₂ with L = 1.5 has an initial discharge capacity of 169 mAh g⁻¹ and an initial charge-discharge efficiency of 94% at 0.2 C rate, and achieves good rate performances from 0.2 C to 5 C.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Improving the electrochemical performance of Li4Ti5O12/Ag composite by an electroless deposition method

Nano-sized silver particle (<20 nm) was highly dispersed on the surface of Li₄Ti₅O₁₂ particles by an electroless deposition method. The Ag additive played a positive role in improving the electrical contact between Li₄Ti₅O₁₂ particles and the current collector and therefore improved the high rate capacity of Li₄Ti₅O₁₂, but it did not take part in the electrochemical reactions with Li⁺ in Li₄Ti₅O₁₂/Ag composite during the cycling. The experimental results showed that the smaller the silver particles and the more homogeneous dispersion of silver particles in the Li₄Ti₅O₁₂ matrix, the better the cycling performance we obtained.     

Microstructure effect on the electrochemical property of Li4Ti5O12 as an anode material for lithium-ion batteries

Porous (P-) and dense (D-) lithium titanate (Li₄Ti₅O₁₂) powders as an anode material for lithium-ion batteries have been synthesized by spray drying followed by solid-state calcination. Electrochemical testing results showed that the discharge capacities of P-Li₄Ti₅O₁₂ are 144 mAh/g, 128 mAh/g and 73 mAh/g at the discharging rate of 2C, 5C and 20C, respectively (cut-off voltages: 0.5-2.5 V). The corresponding values for D-Li₄Ti₅O₁₂ are 108 mAh/g, 25 mAh/g and 17 mAh/g. The higher capacity of the P-Li₄Ti₅O₁₂ at high charge/discharge rates was attributed to the shorter transport path of Li ions and higher electronic conductivity in the P-Li₄Ti₅O₁₂ as a result of its smaller primary particle size and higher surface area compared with those of the D-Li₄Ti₅O₁₂.     

Preparation and electrochemical performance of Li4Ti5O12/carbon/carbon nano-tubes for lithium ion battery

A Li₄Ti₅O₁₂/carbon/carbon nano-tubes (Li₄Ti₅O₁₂/C/CNTs) composite was synthesized by using a solid-state method. For comparison, a Li₄Ti₅O₁₂/carbon (Li₄Ti₅O₁₂/C) composite and a pristine Li₄Ti₅O₁₂ were also synthesized in the present study. The microstructure and morphology of the prepared samples are characterized by XRD and SEM. Electrochemical properties of the samples are evaluated by using galvanostatic discharge/charge tests and AC impedance spectroscopy. The results reveal that the Li₄Ti₅O₁₂/C/CNTs composite exhibits the best rate capability and cycling stability among the samples of Li₄Ti₅O₁₂, Li₄Ti₅O₁₂/C and Li₄Ti₅O₁₂/C/CNTs. At the charge-discharge rate of 0.5 C, 5.0 C and 10.0 C, its discharge capacities were 163 mAh/g, 148 mAh/g and 143 mAh/g, respectively. After 100 cycles at 5.0 C, it remained at 146 mAh/g.     

Structural and electrochemical characteristics of Li4−xAlxTi5O12 as anode material for lithium-ion batteries

Al-doped Li₄Ti₅O₁₂ in the form of Li_4−xAl_xTi₅O₁₂ (x = 0, 0.05, 0.1 and 0.2) was synthesized via solid state reaction in an Ar-flowing atmosphere. Al-doping does not change the phase composition and particle morphology, but easily results in the lattice distortion and thus the poor crystallinity of Li₄Ti₅O₁₂. Al-doping decreases the specific capacity of Li₄Ti₅O₁₂, while improves remarkably its cycling stability at high charge/discharge rate. The substitution of Al for Li site can enhance the electronic conductivity of Li₄Ti₅O₁₂ via the generation of mixing Ti⁴⁺/Ti³⁺, whereas impede the Li-ion diffusion in the lattice. Excessive Al causes large electrode polarization due to the lower Li-ion conductivity, and thus leads to low specific capacity at high current densities. Li_3.9Al_0.1Ti₅O₁₂ exhibits a relatively high specific capacity and an excellent cycling stability.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.     

High-rate characteristics of novel anode Li4Ti5O12/polyacene materials for Li-ion secondary batteries

In recent years, spinel lithium titanate (Li₄Ti₅O₁₂) as a superior anode material for energy storage battery has attracted a great deal of attention because of the excellent Li-ion insertion and extraction reversibility. However, the high-rate characteristics of this material should be improved if it is used as an active material in large batteries. One effective way to achieve this is to prepare electrode materials coated with carbon. A Li₄Ti₅O₁₂/polyacene (PAS) composite were first prepared via an in situ carbonization of phenol-formaldehyde (PF) resin route to form carbon-based composite. The SEM showed that the Li₄Ti₅O₁₂ particles in the composite were more rounded and smaller than the pristine one. The PAS was uniformly dispersed between the Li₄Ti₅O₁₂ particles, which improved the electrical contact between the corresponding Li₄Ti₅O₁₂ particles, and hence the electronic conductivity of composite material. The electronic conductivity of Li₄Ti₅O₁₂/PAS composite is 10⁻¹ S cm⁻¹, which is much higher than 10⁻⁹ S cm⁻¹ of the pristine Li₄Ti₅O₁₂. High specific capacity, especially better high-rate performance was achieved with this Li₄Ti₅O₁₂/PAS electrode material. The initial specific capacity of the sample is 144 mAh/g at 3 C, and it is still 126.2 mAh/g after 200 cycles. By increasing the current density, the sample still maintains excellent cycle performance.     

All solid-state lithium polymer secondary batteries using spinel Li4/3Ti5/3O4 as an active material

Present paper describes electrochemical performance of the all solid-state lithium polymer battery (LBP) using spinel-type Li_4/3Ti_5/3O₄ which has been known as the potential candidate of anode materials.The assembled LPB with Li|solid polymer electrolyte(SPE)|Li_4/3Ti_5/3O₄ construction showed stable charge-discharge cycles more than 300 times at 1 C condition. On the other hand, strong charge-discharge rate dependence for the specific capacity and initial capacity loss was indicated. Such a poor rate performance stemmed from low diffusivity of Li⁺ ion in the by-products produced by the decomposition of SPE components at the SPE|Li_4/3Ti_5/3O₄ interface.     

Hydrothermal synthesis of Li4Ti5O12 microsphere with high capacity as anode material for lithium ion batteries

Lithium titanate (Li₄Ti₅O₁₂) microsphere has been successfully synthesized by a hydrothermal method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology of the prepared Li₄Ti₅O₁₂ crystallites. The results show that the as-synthesized powders exhibit outstanding rate capacities and excellent cycling performance. The first discharge capacity at 0.1 C is 172.5 mAh g⁻¹, which is close to the theoretical capacity of 175 mAh/g. After 50 cycles, the efficiency of the synthesized Li₄Ti₅O₁₂ still retains up to 92.8% at 0.1 C and 95.2% at 0.5 C of its initial value, which present a promising applications as anode materials for lithium ion batteries in hybrid and plug-in hybrid electric vehicles.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

High rate capability and long-term cyclability of Li4Ti4.9V0.1O12 as anode material in lithium ion battery

Li₄Ti_4.9V_0.1O₁₂ nanometric powders were synthesized via a facile solid-state reaction method under inert atmosphere. XRD analyses demonstrated that the V-ions successfully entered the structure of cubic spinel-type Li₄Ti₅O₁₂ (LTO), reduced the lattice parameter and no impurities appeared. Compared with the pristine LTO, the electronic conductivity of Li₄Ti_4.9V_0.1O₁₂ powders is as high as 2.9 × 10⁻¹ S cm⁻¹, which should be attributed to the transformation of some Ti³⁺ from Ti⁴⁺ induced by the efficient V-ions doping and the deficient oxygen condition. Meanwhile, the results of XPS and EDS further proved the coexistence of V⁵⁺ and Ti³⁺ ions. This mixed Ti⁴⁺/Ti³⁺ ions can remarkably improve its cycle stability at high discharge–charge rates because of the enhancement of the electronic conductivity. The images of SEM showed that Li₄Ti_4.9V_0.1O₁₂ powders have smaller particles and narrower particle size distribution under 330 nm. And EIS indicates that Li₄Ti_4.9V_0.1O₁₂ has a faster lithium-ion diffusivity than LTO. Between 1.0 and 2.5 V, the electrochemical performance, especially at high rates, is excellent. The discharge capacities are as high as 166 mAh g⁻¹ at 0.5C and 117.3 mAh g⁻¹ at 5C. At the rate of 2C, it exhibits a long-term cyclability, retaining over 97.9% of its initial discharge capacity beyond 1713 cycles. These outstanding electrochemical performances should be ascribed to its nanometric particle size and high conductivity (both electron and lithium ion). Therefore, the as-prepared material is promising for such extensive applications as plug-in hybrid electric vehicles and electric vehicles.     

Effects of carbon source and carbon content on electrochemical performances of Li4Ti5O12/C prepared by one-step solid-state reaction

Li₄Ti₅O₁₂/C composites were synthesized by one-step solid-state reaction method using four commonly used organic compounds or organic polymers as carbon source, i.e., polyacrylate acid (PAA), citric acid (CA), maleic acid (MA) and polyvinyl alcohol (PVA). The physical characteristics of Li₄Ti₅O₁₂/C composites were investigated by X-ray diffraction, electron microscopy, Raman spectroscopy, particle size distribution and thermogravimetry-derivative thermogravimetry techniques. Their electrochemical properties were characterized by cyclic voltammograms, electrochemical impedance spectra, constant current charge–discharge and rate charge–discharge. These analyses indicated that the carbon source and carbon content have a great effect on the physical and electrochemical performances of Li₄Ti₅O₁₂/C composites. An ideal carbon source and appropriate carbon content effectively improved the electrical contact between the Li₄Ti₅O₁₂ particles, which enhanced the discharge capacity and rate capability of Li₄Ti₅O₁₂/C composites. PAA was the best carbon source for the synthesis of Li₄Ti₅O₁₂/C composites. When the carbon content was 3.49 wt.% (LiOH·H₂O/PAA molar ratio of 1), as-prepared Li₄Ti₅O₁₂/C showed the maximum discharge capacity. At 0.2 C, initial capacity of the optimized sample was 168.6 mAh g⁻¹ with capacity loss of 2.8% after 50 cycles. At 8 and 10 C, it showed discharge capacities of 143.5 and 132.7 mAh g⁻¹, with capacity loss of 8.7 and 9.9% after 50 cycles, respectively.     

Effects of the starting materials and mechanochemical activation on the properties of solid-state reacted Li4Ti5O12 for lithium ion batteries

Li₄Ti₅O₁₂ was synthesized by a solid-state reaction between Li₂CO₃ and TiO₂ for applications in lithium ion batteries. The effects of the TiO₂ phase and mechanochemical activation on the Li₄Ti₅O₁₂ particles as well as the corresponding electrochemical properties were investigated. Rutile TiO₂ was more desirable in acquiring high purity Li₄Ti₅O₁₂ than anatase due to the anatase to rutile phase transformation, which was found to be more rigid in the solid-state reaction than the intact rutile phase. Mechanochemical activation of the starting materials was effective in decreasing the reaction temperature and particle size as well as increasing the Li₄Ti₅O₁₂ content. The specific capacity depended significantly on the Li₄Ti₅O₁₂ content, whereas the rate capability improved with decreasing particle size due to the enhanced contact area and reduced diffusion path. Overall, a 200 nm-sized Li₄Ti₅O₁₂ powder with a specific capacity of 165 mAh/g could be synthesized by optimizing the milling method and starting materials.     

Electrochemical performance of Li4Mn5O12 nano-crystallites prepared by spray-drying-assisted solid state reactions

Nanosized Li₄Mn₅O₁₂ has been synthesized by a spray-drying-assisted solid state method. The effect of spray drying and drying temperature on the microstructure and electrochemical performance of the final products has been investigated. The microstructure of the products has been characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The electrochemical performance of the products has been studied by galvanostatic cycling, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). It has been found that the products prepared with a spray-drying pretreatment of the precursor exhibit a smaller grain size and a narrower size distribution than that prepared without the pretreatment. Among the three samples with a precursor pretreatment, that pretreated at 250 °C shows the best electrochemical performance due to the smallest grain size of below 50 nm and the narrowest size distribution.     

Preparation and characterization of ramsdellite Li2Ti3O7 as an anode material for asymmetric supercapacitors

Ramsdellite Li₂Ti₃O₇ was first synthesized via sol-gel process with good crystallity of an average particle size of 0.175 μm. The product was thoroughly investigated as a lithium intercalation compound, and as an active anode material in asymmetric supercapacitors coupling with activated carbon as cathode. Lithium intercalation reactions were found occurring at 1.32 and 1.62 V versus Li/Li⁺, respectively. A reversible specific capacity of 150 mA h g⁻¹ at 1C was obtained on Li₂Ti₃O₇ electrode in a nonaqueous electrolyte. The charge current was found to strongly influence the anodic discharge capacity in the asymmetric cell. The capacity retention at 10C charge-discharge rate was found to be 75.9% in comparison with that at 1C.     

Aging characteristics of high-power lithium-ion cells with LiNi0.8Co0.15Al0.05O2 and Li4/3Ti5/3O4 electrodes

The impedance rise that results from the accelerated aging of high-power lithium-ion cells containing LiNi_0.8Co_0.15Al_0.05O₂-based positive and graphite-based negative electrodes is dominated by contributions from the positive electrode. Data from various diagnostic experiments have indicated that a general degradation of the ionic pathway, apparently caused by surface film formation on the oxide particles, produces the positive electrode interface rise. One mechanistic hypothesis postulates that these surface films are components of the negative electrode solid electrolyte interphase (SEI) layer that migrate through the electrolyte and separator and subsequently coat the positive electrode. This hypothesis is examined in this article by subjecting cells with LiNi_0.8Co_0.15Al_0.05O₂-based positive and Li_4/3Ti_5/3O₄-based negative electrodes to accelerated aging. The impedance rise in these cells was observed to be almost entirely from the positive electrode. Because reduction products are not expected on the 1.55 V Li_4/3Ti_5/3O₄ electrode, the positive electrode impedance cannot be attributed to the migration of SEI-type fragments from the negative electrode. It follows then that the impedance rise results from mechanisms that are “intrinsic” to the positive electrode.